Laurel Hill Quarry Metal/Non-Metal

Employee was disconnecting a small water line. When kneeling down/bending over employee felt a sharp pain in lower back (left side)

While employee was loading material in the pit, the employee hit a toe in the pit floor causing the loader to jerk. This incident occurred on 5/23/2024, but the safety department was not notified until 8/6/2024. When the employee was stating they now needed care.

Shoveling material off of belt, when they tossed the stone with shovel in hand heard a "POP" in left shoulder.

Cutting rubber skirting to put on screen deck, was cutting away from belt and knife slipped and went across EE's left leg.

Chute got backed up, hit with sledge hammer four times and hurt right shoulder. Unspecified sprain of right shoulder joint.

Pre-existing medical condition.

While washing off bulldozer employee slipped off a step, hitting his left shin and causing a laceration requiring sutures.

While installing metal mesh guard hit left thumb with hammer resulting in fracture.

Reinstalling cooler door, caught rt. index finger between door and cooler frame, causing finger tip contusion.

Employee was working in the precipitator with the electrician to install shock bars. Employee was receiving the shock bar from the electrician. Employee said to stop pushing the shock bar and eletrician did not hear him due to noise. With electrician still pushing shock bar, employee's left hand got pinched between shock bar and frame of precipitator.

Employee was working in the precipitator assisting the plant electrician in removing tumbling hammers, when the employee cut his right thumb. The employee was holding a tumbling hammer in both hands, while the electrician attempted to cut the right side pin with a hand held grinder with a cutting wheel. The grinder jumped out and struck the employee's thumb.

The employee was walking down steps along side the shipping silos, when he hit some built-up material on one of the steps and turned his right ankle. The employee thought his ankle would be okay, but as the day progressed, it swelled up considerably. As a result, the employee started experiencing discomfort and asked to receive medical treatment.

The employee was working in belt 16 tunnel, installing a sump pump. It was discovered that the employee was working in ankle deep water, which was full of limestone dust. The employee's immediate supervisor asked him to put rubber boots on, but he advised the supervisor that he did not need them. Unfortunately, the employee incurred limestone burns on both of his feet.

Employee was welding a steel plate inside belt 18 head pulley chute. During the job, welding sparks caught the employee's right pant leg on fire, burning his right leg. Employee did nothing wrong. He was wearing the proper welding hood and arm sleeves at the time. Considering the confined space, welding sparks were a lot closer than if welding in an open area!

The employee was shoveling material off of the screen house landings when he felt a slight pain in his back.

The employee was cleaning along belt 16. As he attempted to raise the belt scraper from the belt, limestone dust from the immediate area blew into both his eyes, causing irritation and redness. He was able to flush out the material from his right eye, but not his left. As a result, he was transported by a supervisor to receive further medical treatment.

Laborer was shoveling shale debris which contained some lime dust and it burned parts of his body when he would sweat and a chemical reaction between the sweat and lime took place.

The employee was shoveling and using a pick axe an aggregate near dryer/kiln when he felt a twinge in his lower back. He was operating in the standard manner with no contribution to the accident and no failure to follow safety rules.

EE WAS WALKING ALONG BELT 30 CATWALK WHEN THE WIND PICKED UP, CAUSING A DUST CLOUD TO FORM IN HIS PATH OF TRAVEL. PARTICLES FROM THE DUST CLOUD ENTERED EE'S LEFT EYE. IRRITATION AND TEARING RESULTED IMMEDIATELY. PRESCRIPTION AND RESTRICTIONS ISSUED.

EE WAS SHOVELING MATERIAL ALONG BELT 4 TAIL PULLEY WHEN HE EXPERIENCED PAIN IN HIS LOWER BACK. EE MENTIONED HE MAY HAVE TWISTED HIS BACK WHILE SHOVELING MATERIAL IN FRONT OF HIM TO THE SIDE. PRESCRIPTION AND RESTRICTIONS ISSUED.

EE WAS ATTEMPTING TO START A CHAIN SAW WHEN HE ENCOUNTERED SHARP PAIN IN HIS UPPER LEFT SHOULDER AND BACK AREA. PRESCRIPTION AND RESTRICTIONS ISSUED.

EE WAS DESCENDING ON STAIRWAY LEADING FROM BELT 20 HEAD PULLEY TO LOWER LEVEL WHEN HE CAME OFF LAST STEP ONTO SURGE BIN PLATFORM. HE STEPPED ON A ROCK APPROX. 1" IN DIAMETER, TWISTING HIS LEFT ANKLE. SPLINT/BRACE PRESCRIBED; CRUTCHES ISSUED.

EE HAD LOWER BACK PAIN CONTINUING DOWN BELOW HIS LEFT KNEE. EE COULD NOT SAY WHEN, HOW OR WHERE HE HURT HIS BACK. COMPANY DOCTOR PLACED EE ON LIGHT DUTY; EE REFUSED & WENT TO PERSONAL PHYSICIAN. WORKERS' COMP. AWARD 5/3/05: TEMP. TOTAL DISAB. DUE TO WORK-RELATED ACCIDENTAL INJURY (SWINGING SLEDGE HAMMER, INSTALLING PINION GEAR FOR ROLL CRUSHER). SURGERY PENDING.

EE WAS ATTEMPTING TO CLIMB UP THE XPM SILO WHEN HE FELT PAIN IN HIS RIGHT ELBOW (POSSIBLY PULLED A MUSCLE OR STRAINED HIS ARM). PRESCRIPTION AND RESTRICTIONS ISSUED.

Ee was cleaning idlers along belt 4 tail pulley area when his hand was caught between the running belt and #2 & #3 idlers on the west side. He was advised in the past not to clean idlers when the belt was running. He failed to do so. He also admitted to his supervisor that he should not have been cleaning the idlers while the belt was in operation.

EE was walking through maintenance dept while maint ee's were hammering a pin. The pin flew out and struck ee in the left eye, cracking his safety glasses. EE got glass in his left eye as a result of his glasses cracking. EE was issued a prescription.

*REOCCURRENCE FROM LAST JULY, WHICH WAS NOT REPORTABLE AT THE TIME* EE WAS USING A LONG METAL ROD/BAR WITH AN END HOOK TO FREE CLINKER WHEN HIS RIGHT HAND AND ARM WERE JERKED FORWARD. EE EXPERIENCED A BURNING SENSATION IN HIS RIGHT SHOULDER. IT DID NOT GO AWAY AND IS ANNOYING. EE CLAIMS POOR LIGHTING WAS A FACTOR IN RECEIVING THE INJURY. LOST TIME STARTS ON 5/4/05.

EMPLOYEE EXPERIENCED INCREASING IRRITATION AND RASH ON LEGS AND ARMS. EMPLOYEE HAD A SIMILAR PROBLEM IN THE PAST THAT WAS RESOLVED WITH LOTIONS. HIGHER LIME CONTENT IN THE QUARRY STONE PLAYED A PART IN THE PAST AND, MOST LIKELY, HIGH LIME CONTENT IS THE REASON AGAIN. EMPLOYEE WAS ISSUED A PRESCRIPTION (PREDNISONE TAPER) TO RELIEVE THE RASH.

Employee was changing a light bulb in the coal tunnel and fell off his ladder hurting his lower back. Ladder slipped out from under him, causing him to fall.

EMPLOYEE WAS AT BELT 18 CONVEYOR HEAD PULLEY PREPARING TO CLEAN THE MAGNET THAT COLLECTS METAL COMING OFF BELT. EE DROPPED PLATE DOWN TO POSITION TRAY UNDER MAGNET. WHILE POSITIONING TRAY, PLA TE WENT TO DROP & EE REACTED BY GRABBING THE PLATE & DOING SO USED HIS HAND TO GRAB PLATE, HIS HAND STRUCK BELT ON HEAD PULLEY AND EDGE OF PLATE WHICH SLICED HIS RIGHT THUMB.

EE WAS BENDING DOWN IN KILN WHEN A PIECE OF COATING FROM INSIDE KILN FELL & STRUCK HIM IN THE LOWER BACK.

EE WAS SCRAPING & CLEANING GREASE OFF OF METAL SEAL AND BRASS BUSHING ON THE TERTIARY CRUSHER. WHILE CLEANING EE FINGER WAS LACERATED BY THE SHARP EDGE OF THE SEAL. THE RIGHT PINKY FINGER WAS LACERATED AND REQUIRED STITCHES.

EMPLOYEE WAS CHANGING A HYDRAULIC HOSE ON A MICHIGAN LOADER. WHILE USING WRENCH ON HOSE FITTING, WRENCH SLIPPED OFF AND SMASHED TWO FINGERS ON RIGHT HAND.

EE STATES THAT HE WAS WORKING ON GROUND FLOOR WHEN SOMEONE DROPPED SOMETHING OVERHEAD CAUSING A CLOUD OF DUST TO COME DOWN - FLY ASH IN EYE.

INJURED REMEMBERED THAT AFTER REPLACING THE BREAKER, HE ONLY PUSHED THE BREAKER BACK ON THE STABS IN THE CABINET & DIDN'T SECURE IT. HE BORROWED A LONG SCREWDRIVER BECAUSE HIS INSULATED SCREWD RIVER WASN'T LONG ENOUGH. HE TIGHTENED THE UPPER RIGHT HOLDING SCREW & WENT TO TIGHTEN THE UPPER LEFT HOLDING SCREW & APPARENTLY TOUCHED THE SCREWDRIVER TO THE LEFT CONTACT & IT SHOCKED HIM.

EMPLOYEE, ELECTRICIAN A, WAS CLOSING DOOR TO BREAKER BOX. WHILE POSITIONING WIRES, HE CONTACTED THE WIRE ON THE METER ON THE DOOR. AND GOT SHOCKED. DUE TO SHOCK, IT CAUSED HIS RIGHT SHOULDER MUSCLE TO CONTRACT AND DUE TO BONE SPUR IN SHOULDER, CAUSED PAIN IN RIGHT SHOULDER.

EE & CO-WORKER WERE REMOVING OLD TRANSITE SIDINGOFF OF THE PRECIPITATOR BLDG. USING A MAN-LIFT. EE WAS HOLDING A 4'X 8'PIECE OF SIDING WHILE CO-WORKER WAS BACKING OUT LAST SCREW HOLDING THE SIDING. THE SIDING SLIPPED WHEN IT BECAME FREE FROM THE BLDG. & IT DROPPED ABRUPTLY. EE GRABBEDIT & HELD IT FOR AWHILE. HE FINALLY LET IT DROP WHEN HE FELT A SHARP PAIN IN STOMACH AREA.

EMPLOYEE WAS CUTTING WIRE OFF OF WIRING TO R35 HAUL TRUCK WITH PEN KNIFE. KNIFE CUT THROUGH WIRE TIE AND LACERATED HAND.

INJURED EMPLOYEE WAS RIDING IN R35 TRUCK FROM QUARRY TO PLANT FOR LUNCH. TRUCK OPERATOR PARKED TRUCK, SET PARKING BRAKE. INJURED EXITED CAB AND PROCEEDED ON CATWALK TO LADDER OF TRUCK. WHEN OP ERATOR TOOK FOOT OFF BRAKE, TRUCK LURCHED FORWARD, CAUSING INJURED TO LOSE BALANCE AND FALL APPROX. 7' TO GROUND. INJURED STATED HE SHOULD HAVE WAITED FOR TRUCK TO BE SAFELY STOPPED.

EMPLOYEE WAS ASSISTING REMOVAL OF 988 LOADER RADIATOR. EMPLOYEE USING PRY BAR TO HOLD RADIATOR WHILE REMOVING BOLTS. PRY BAR BROKE LOOSE FROM RADIATOR CAUSING EMPLOYEE TO LOSE BALANCE. HE FELL 5 FT APPROX TO CONCRETE PAD.

EE SHOVELING WALKWAY OF BELT 12 CONVEYOR. GLASSES GOT FOGGED DUE TO HUMIDITY. EE LAID GLASSES ON BELT TRAY. GLOVE GOT CLOSE TO PINCH POINT OF IDLER AND BELT. PULLED EE'S RIGHT ARM IN PINCH POI NT. BELT WAS MOVING SLOW, EE PULLED STOP CORD TOSTOP BELT AND PULLED OUT ARM.

CUTTING V-BELT OFF OF RAW SCREEN #1 MOTOR, EMPLOYEE LACERATED FINGER WITH KNIFE.

EE WAS CLEANING BELT 12 DISCHARGE CHUTE TO BELT 13 WITH A BAR. WHILE POKING THE CHUTE HE STRUCK HIS LEFT FOREARM ON THE HANDRAIL, CAUSING A CONTUSION.

EMPLOYEE WAS CHECKING ALONG BELT #23 CONVEYOR AT SOUTH ENTRANCE OF SCREENHOUSE. WHEN EMPLOYEE STEPPED ON THE CATWALK GRATING APPROX. 20 FEET FROM SCREENHOUSE, IT GAVE WAY AND EMPLOYEE FELL APP ROX. 6 FEET TO THE GROUND. IT APPEARS THAT THE SIDE RAIL HOLDING THE GRATING HAD BEEN BENT CAUSING GRATING TO SHIFT AND FALL.

EE WAS DESCENDING STAIRS FROM SHIPPING OFFICE, MISSED LAST STEP TWISTED LEFT ANKLE.

10-1-96- APPROX 7:00 PM, EE STRUCK BEAM TO DUST BIN WITH HAUL TRUCK. 10-2-96 - APPROX 7:40 AM, DUST BIN, DUST ELEVATOR, AND SUPPORTING STEEL STRUCTURES COLLAPSED CAUSING INJURED EE TO TRY TO E SCAPE AND EITHER FELL OR TRIPPED OFF OF PLATFORM AT DUST BIN. SHE FELL 8 TO 10 FT TO GROUND LEVEL.

A PICK UP TRUCK WAS POSITIONED NEXT TO 560 LOADER ENGINE TO ENABLE EE TO WORK FROM BED OF TRUCK AND STEP UP TO ENGINE COMPARTMENT. WHEN INJURED EE WENT TO STEP DOWN INTO BED OF PICKUP TRUCK, H E STEPPED ONTO A LARGE BOLT AND TWISTED HIS ANKLE.

EMPLOYEE DESCENDING DOWN CONCRETE STEPS IN BACK OF MAIN OFFICE. WHEN REACHING LAST STEP, MISJUDGED AND FELL, FALLING ON WRIST.

EE CHANGING IDLER ON BELT 22 CONVEYOR. WHILE USING RATCHET AND WRENCH TO REMOVE, BOLTS, WRENCH SLIPPED OFF NUT, CAUSING FINGER TO BE PINCHED BETWEEN FRAME AND WRENCH.

EMPLOYEE WAS STANDING ON SIDEOF ENGINE COMPARTMENT OFMICHIGAN FRONT END LOADER ATTEMPTIGN TO ADJUST TARP USED TO COVER ENGINE COMPARTMENT DUE TO COLD WEATHER. WHILE REACHING FOR TARP, LOST BA LANCE AND FELL OFF SIDE OF LOADER APPROX 8'.

EMPLOYEE WAS REMOVING AND STACKING STEEL HOLD DOWN BARS FOR WOBBLER CHAIN. ONE BAR SLIPPED AND LACERATED RIGHT HAND.

EMPLOYEE WAS OPERATING PORTABLE GRINDER ON CARRYALL PAN.WHEN CLIMBING OUT OF PAN HE LIFTED GRINDER BY HANDLE.HE ACCIDENTALLY HOT ON BUTTON,GRINDER WAS TOUCHING LEG,GRINDER ACTIVATED BRIEFLY,ST RIKING LEG.

EMPLOYEE WAS CLEANING FINISH DEPARTMENT SCREENS WITH JACKHAMMER. HE RECEIVED A BLISTER ON RIGHT HAND WHICH BECAME INFECTED AND CAUSED BLOOD POISON. HE RECEIVED A TETANUS SHOT AND MEDICINE ON 9 -21-91.

EMPLOYEE WAS TORCHING AND REMOVING OLD EQUIPMENT IN KILN AREA. WIND BLEW PIECE OF FOREIGN MATERIAL INTO LEFT EYE. DIDN'T BOTHER HIM UNTIL NEXT MORNING WHEN HEREPORTED. THIS INJURY OCCURRED 3/91 WITH NO LOST TIME, BUT IN 5/91 BECAME REPORTABLE DUE TO CATARACT SURGURY, BUT STILL DID NOT RESULT IN LOST TIME.

IT WAS SNOWING AND EMPLOYEE WAS TRAVELING ON HAUL ROAD DRIVING A R35 EUCLID HAUL TRUCK LOADED WITH A LOAD OF SLATE.HE WAS DRIVING TOO CLOSE TO RIGHT EDGE OF ROAD WHEN WHEELS HIT THE SOFT MATER IAL CAUSINF THE TRUCK TO SINK DOWN NOT ALLOWING THE TRUCK TO BE STEERED BACK ONTO ROADWAY.THE TRUCK LAID OVER ON ITS RIGHT SIDE AFTER DROPPING OFF OF ROADWAY APPROX 2 TO 3 FT.EMPLOYEES SEAT B

TWO EE WERE CLEANING OUT UNDER FINISH SCREEN DECK NO. 10 AND 8. AFTER CLEANING, ONE EE HAD TO LEAVE AND INJURED EE WAS TOLD TO REINSTALL ACCESS DOOR. WHILE INSTALLING DOOR, IT SLIPPED OFF OF F RAMEWORK EDGE AND FELL ONTO EE FINGERS.

A CHOKE UP OF MATERIAL OCCURRED IN CHUTE FROM BELT 21 TO BELT 25 IN FINISH DEPARTMENT. EMPLOYEE TOOK A ROD AND POKED AT MATERIAL TO DISLODGE CHOKE UP. A CHUNK OF MATERIAL BROKE LOOSE AND AS HE BEGAN TO REMOVE WITH HIS HAND, HE CUT HIS WRIST ON A JAGGED PIECE OF METAL ON ACCESS DOOR FRAMEWORK.

2 EES WERE PREP5RING TO INSTALL FLOOR DECK AT SCREENHOUSE BELT 18 AREA. THEY WERE REMOVING UPRIGHT & DIAGONAL BEAMS BY TORCHING BOLTS. WHILE REMOVING BOLTS DIAGONAL BEAM BROKE FREE OF UPRIGH T & FELL THRU F5OOR OPENING APPARENTLY HIT GORUND FLIPPED & STRUCK EE. EE WAS NOT DIRECTLY UNDER WORK AREA BUT WAS TO T HE SIDE.

EMPL CUTTING OU7 TREES IN FENCEROW.LIMB WAS TWISTED AND WHILE FINISHING CUT,IT BROKE AND FELL ONTO EMPL LEFT HAND MASHING AND LACERATING INDEX FINGER.

EMPLOYEE WAS CH9CKING WATER LINES ATBELT 16 HEAD PULLEY. WHILE PERFORMING CHECK, A HEAVY GUST OF WIND CAME UP AND BLEW DUSTY MATERIAL INTO EYE.

EMP WAS DISLODG3NG MATERIAL HUNG UP ON FRAMEWORK AT FINES PILE HE WAS STANDING ON LADDER STEADYING HIMSELF WITH ONE HAND AND USING 8 LB SLEDGE HAMMER WITH THE OTHER HAND HE STRUCK MATERIAL WHICH WAS HARD 8LEDGE GLANCED OFF MATERIAL AND STRUCK HIS RT WRIST

EMP WAS MOVING CONVEYOR TAIL PULLEY DOWN STEPS TO BELT CONVEYOR PULLEY SLID PINCHING EMPLOYEES FINGER AGAINST RAILING

EMPLOYEE WAS H AULING STEAMING STONE FROM TOP OF QUARRY RAMP TO QUARRY FLOOR FOR EXPLOSIVE VENDER. RAMP WAS SNOW COVERED BUT WAS SCRAPED WITH 966 FRONT END LOADER AFTER THREE STRIPS WITH STON E WITH MET TOO MUCH DIFFICULTY OF SLIPPING ON THE FOURTH TRIP, WHEELS WOULD NOT KEEP TRACTION LOADER TRAVELED DOWN RAMP, CAME TO A STEP IN DRAINAGE DITCH, THEN OVERTURNED.

EE WAS REPLACING METAL SKIRTING ON #2 RAW SILO FEEDOWEIGHT. AFTER REMOVING SKIRTING USING A CUTTING TORCH HE CUT OUT WORN METAL FOR REPLACING. WHILE CUTTING THE SKIRTING WHICH WAS POSITIONED ON T HE FEEDOWEIGHT FRAME THE PIECE OF SKIRTING FELL OFF THE FRAME FALLING APPROX 3\ HIT THE DEAD MAN CABLE SPRUNG UP & CAME DOWN END FIRST & STRUCK EES RIGHT FOOT BEHIND STEEL CAP ON SHOE.