Mine No. 43: 1,284 citaciones de la MSHA Coal

Employee was walking along scoop and got stuck in the mud, lost balance and fell into the batteries of the scoop injuring ribs.

EE was walking to the power center from the feeder area, when EE caught EE's foot on a rock and fell twisting EE's lower back. EE has started missing work from this injury.

Employee was operating the continuous miner and after backing from a cut, EE reached down to move the cable, when EE was struck by a piece of rock from the roof & rib. EE suffered bruising to the back and abdomen area.

Employee is a Roof bolter operator on 2 Right Section, when they put a strap in place and rotated the bolt. The strap moved resulting in a cut to middle finger of right hand. The laceration was cleaned and closed with glue.

Employee is a scoop operator on the South Mains section. Employee was putting roof bolt plates on the bolter supply tray, as they turned, they heard a pop and felt pain in left knee.

Employee was cleaning the threads on a bolt with a wire wheel when one of the wires came off and struck EE in the left eye. The employee was wearing safety glasses and fellow employees in the area confirmed the use of glasses.

Employee was loading bolting supplies on a dual head bolting machine. As EE was loading supplies, EE struck left knee against the machine.

Employee was working on the 4 Right Section and EE was helping move the C/M and as EE was hanging the cable EE felt pain in lower back.

An unintentional roof fall occurred in the No. 8 entry on the North Mains section. The fall occurred as the Continuous Miner operator was backing the miner out of the last lift. Material fell from the lift just completed and extended into the entry, pulling bolts and catching the miner head. No Injuries were suffered from this event.

An unintentional roof fall occurred in the 3 Left cross- cut of the North Mains unit. The fall occurred in the cut and travelled into the intersection. Area was approximately 16 to 18 feet wide, 30 feet long and approximately 10 to 12 feet high at the highest point. Area involved was two crosscuts inby spad 2129.

Was informed by letter that employee has evidence of pneumoconiosis.

Employee was loading a piece top structure into a scoop bucket and strained their back.

Employee was moving a water hose for a C/M from mud, when the employee felt pain in lower back. The injury occurred in wet & muddy conditions. X-Rays were negative and employee was diagnosed with a strain.

Employee was hanging cable when rubber tire on mantrip hit foot.

A miner received injuries while they and two coworkers were repairing a belt splice on the 1A conveyor belt. The miner had positioned themselves on top of the conveyor belt when it started.

Employee was riding the section mantrip to the surface after shift had completed. Employee was on knees when employee's jacket caught a roof bolt and employee then turned over. Employee continued to work until 5/5/2019 when employee first received medical attention.

A non-injury event occurred on MMU 001/ MMU 003 Mains Section, when a continuous miner cutting in the #7 Entry struck a borehole and water discharged into the mine.

Employee was operating a shuttle car and as employee was attempting to move the C/M cable out of the roadway. Employee slipped in the wet muddy conditions and rolled ankle.

Unplanned roof fall occurred in the last open crosscut between the #1 and #2 entries inby spad 1548. The fall was approximately 16 feet wide and 30 feet long and about 6 foot high.

Employee was pulling pump cable through a stopping, when EE slipped on the cable and twisted EE's left knee. Employee went to the Dr on 7/23/2018

Employee was walking to check on water sprays when ee stepped on a rock twisting right Ankle.

Drill steel came out of the hole, struck the drill boom then glanced into the employees face, causing a laceration to lower lip. Wound required stitches to close.

During installation of a 10' fly board it slipped off the ATRS when glue was being placed in the hole.

A non-injury roof fall occurred in the #5 Heading while retreat mining was being conducted inby the 7th Crosscut of the 3 left Panel. Fall pulled roof bolts and caught the continuous miner in the 4th lift of the entry.

Contractor EE was operating a roof bolting machine, while installing a fly board to the mine roof, the fly board flexed and sprung upward, pinching the EE's finger.

The surface high wall having connecting underground mine portal entries, failed to remain competent in solid form, resulting in rock strata breaking away directly over top of the No.6 mine portal entry and damaging two rows of permanent roof support, having been installed in the underground mine roof(s) immediate portal opening.

The employee was tramming a continuous miner out of a pillar lift extraction, when the trailing cable caught left leg, resulting in the employee twisting knee.

Employee was carrying two cans of hydraulic oil, slipped and fell backwards.

While operating the roof bolter, the employee got his fingers caught between the roof bolter canopy and the mine roof.