Richland No 9 Coal

While pulling feeder to outside FM xc2 making the turn at xc1 slop[e bottom. The feeder slid to corner of rib causing the chain to break striking EE on forehead toward right eye. A laceration of about 1.5 inches was treated by MET and was transported to RMC.

A rock fall occurred on No. 1 unit on 5th East Main at spad No. 15 + 50 in No. 3 Entry Intersection. 18 ft wide, 22ft in length and 8 ft high. The area is dangered off and cribs installed and barricaded off. Additional cribs are also installed across face and all three entries & crosscuts 15 + 50.

A roof fall occurred on No. 1 unit on 5th East Main at spad No. 15 + 50 in No. 1 Entry last open intersection. 18 ft wide by 35 ft long by 8 ft high. the area is dangered off and cribs installed and barricaded off. No equipment involved.

Employee was "squaring up" pinner into No 3 right x-cut with the side control tram levers when pinner shocked him and lost power. Investigators discovered a grounded cable on the reel and ineffective insulated tram lever control covers due to age and wear contributed to employee receiving shock.

An inundation of water occurred on the No. 1 unit in the No. 2 entry at x-cut left of MMU-005-0 section at spad No. 11 + 09. The working section is presently under a 103-K order issued by MSHA on 5/14/14 at 0036 hour.

Employee stated he was struck across bridge of his nose by roof bolter's trailing cable, causing fracture to his nose requiring surgery to his nasal system on 9-16-13 --- Employee started missing work on 9-16-13.

EE stated he was building a concrete block ventilation stopping. Cut a steel band with hammer that was holding block onto a pallet. When the band was cut one end came up and struck EE's right hand causing a laceration requiring six stitches.

Employee stated he was loading 8 foot cable bolts onto the double boom roof bolter...struck his left forearm against an overhead roof bolt plate causing a laceration requiring 15 stitches...employee did not miss any work.

Employee stated he was operating opposite double boom roof bolter drilling a one inch into the roof, piece of draw rock fell from roof. Reposition drill steel when up pressure was applied the drill steel snapped in two striking employee over his right eye brow.

Employee stated while building a concrete stopping he was in the process of splitting a block when he struck his right forearm against a steel band...causing small laceration requiring nine stitches...no lost time

EE stated he was unwinding a spool of elec. cable. Reel was suspended from the roof cable became fouled causing reel to swing back towards EE's face he threw up his right arm to catch reel when his ring finger was caught by the chain holding the cable reel and severing the end of his ring finger back to the first joint.

Employee stated he was changing miner bits. Struck bit wrench with hammer, small chip of steel off hammer struck employee's right upper arm, penetrating the biceps muscle. Piece of steel was removed by Dr.

EE stated he was installing belt key hold hangers into mine roof. Pinner steel struck EE across left forehead above eye brow requiring 7 stitches EE RTW on same shift.

A roof fall occurred in the main west at xcut 39 spad 4 & 80 in the #2 return entry. Length 19' x Width 18' x Height 8'. Area developed 12/23/07.

A roof fall occurred on 6/2/11 at spad # 13 & 30 in the #2 return entry. Fall was 18'W. X 30' L. X 6' H. Did not affect flow of air and will not be cleaned up. No equipment involved.

EE stated he was operating battery scoop hauling mud-muck and loose rock that had been piled up in XC between supply road and belt entries. While backing the scoop a large piece of rock came in operators compartment struck the EE on his left shoulder causing contusion. EE started missing work on 5/27/11.

EE stated he was replacing conveyor chain on a joy 21sc shuttle car using a com-a-long. Chain broke on the com-a-long causing ee to fall backward, causing a possible strain to ee back and neck. EE started missing work on 4/14/11.

Employee stated he was changing insert on drill steel. Roof bolter operator moved the roof bolting machine forward. Right front wheel (tire) ran upon employee's right foot causing a sprain. Started missing work on 3/22/11.

Occurred during the week of 2/10/11 thru 2/17/11. Roof fall was found on the weekly examination by EE and MSHA inspector. High 12ft X Width 20ft X Long 45ft at spad No.4t80 in the main west No. 1 entry. Return air course.

A roof fall occurred in East sub main at spad No. 13+00 in the No.3 entry. 35' long x 20' wide x 6' high. Roof fall won't be rehabilitated. All available entrances to roof fall will be supported according to our roof control plan. No equipment involved. Did not impair ventilation, nor impede travelway.

Employee stated he stepped off roof bolting machine and felt pain in left knee. Started missing work on 4/29/10. Returned to work on 5/3/10.

Employee stated he was changing transmission in a Dapco three wheel rib runner. While lifting up on the transmission, employee stated he felt a sharp pain in his back. Started missing work on 12/16/09.

Employee stated he was working with a crew in the process of moving the mining equipment power cables up two crosscuts. His feet became entangled in a roof bolter machine cable loop causing the employee to fall causing pain to his right side. Employee started missing work on 11-6-09.

EE stated shuttle car anchor came loose that was attached to a bolt anchor to the mine roof. Cable struck EE on his right side which caused a contusion. EE started missing work on 11/05/09 RTW 11/09/09.

Employee stated he was using a belt knife. Knife slipped while cutting curtain causing laceration to right leg. Nine stitches - no lost work days.

EE stated cable broke that was holding up hood on a 10-person alpha mantrip. Struck EE on top of head (left side) (wearing hardhat), causing a possible concussion. EE started missing work on 10/2/09.

EE stated he was riding in Wallace 14 person man trip. Ran over pot hole in supply road. Causing pain to employee's back. Started missing work on 8/27/09. Scheduled to return to work on 8/31/09.

EE stated he was connecting a pull rope (wire rope) to cat.245 back hoe. Cut ring finger on right hand. Required 13 stitches. EE returned to work on 8/26/09, did not miss any scheduled work days.

EE stated he was walking down slope. Slipped and fell, causing pain in lower back. Started missing work on 7/31/09

EE stated he was crossing a belt, hung his right foot on belt rope, causing him to fall off belt. Struck 3" water line, causing pain to his lower back. Started missing time on 7/28/09

Employee stated he was removing a belt "A" frame from mine roof. One end of belt "A" frame dropped down. Other end caught left hand ring finger between roof and "A" frame causing laceration to finger requiring 17 stitches.

Employee stated he was walking under a back-up ventilation curtain, struck his left knee against shuttle car bumper causing his left leg to hyper-extend causing pain to left leg.

A roof fall occurred at spad #4+80 in the no. 3 entry in the first main west supply road....width 20 ft x length 30 ft x high 12 ft.

Slope entry was slick causing mantrip to slide striking steel square set cauisng pain to back and right hip started missing work on 12/11/08.

Slope entry was slick causing mantrip to slide striking steel square set causing pain to back, arms and neck area started missing work on 12/11/08

Slope entry was slick causing mantrip to slide striking steel square set causing pain to back and neck area started missing work on 12/11/08.

Slope entry was slick causing mantrip to slide striking steel square set causing pain to right shoulder started missing work on 12/11/08

Employee was using electrical hand held drill, drilling hole into steel lid. Drill bit hung causing drill to rotate, caught employee's right thumb in cord requiring 12 stitches to laceration on thumb. Did not miss any work days.

A roof fall occurred in the Main West No. 6 entry (intake) at spad No. 5+40. Length 30 ft x 20 ft wide x 12 ft high. No equip or ventilation affected.

EE stated he was drilling roof bolt hole in mine roof, piece of draw rock fell from roof, struck EE on his left hand and caused contusion to left hand.

Employee stated he was involved in changing out a pot on a continuous miner, cleaning area where new pot would go. His left hand was caught between pot and frame of continuous miner, causing fracture to middle finger and laceration to ring finger on left hand.

EE stated he removed belt framing from belt trailer. He dropped a piece of belt framing on top of his right foot causing swelling and appearance of a contusion to employee's entire foot. Started missing work on 3/20/08, returned to work on 3/25/08.

Employee stated he stepped off the Cat. 910 forklift onto the diesel scoop. Footing slipped. Fell off top of diesel scoop, approximately 3 1/2 feet high. Dislocated right shoulder.

Employee stated he was operating a shuttle car, struck bump in haul road, felt pain in lower back. Started missing work on 11-5-07.

EE stated he was using a pry bar to change out belt rollers, prying down on belt and felt pain in his lower back, started missing work on 11/3/07.

Employee stated he was aligning the shuttle car cable into the cable reel. Cable jerked employee's right hand into cable reel causing a laceration and fracture to his right hand forefinger. Employee did not miss any time.

EE stated he was helping the mechanic change a hyd. hose on a double boom roof bolter. He raised the boom, struck the bit tray, tray fell, struck employee's left hand between tray and joy stick knob causing laceration to the left forefinger requiring 14 stitches. Did not miss any time.

Employee stated he was hanging the continuous miner cable. felt pain in his back started missing work on 9/8/07

Employee stated he was reaching for a roof bolt and felt pain in his leg leg and knee-He was working on his knee's intalling permanent roof support-missed three work days returned to work on 9/13/07 started missing work on 9/10/07.

Employee stated he was pulling continuous miner cable. Strap being used to pull cable pulled in two. Piece of strap came off cable & struck employee on right hand, near his right thumb causing a laceration requiring seven stitches. Employee returned to work on 8/24/07 - missed one day.

Employee stated he was riding in mantrip & a piece of small black slate fell from mine roof & struck him on his chin causing a small laceration requiring five stitches. Employee did not miss any work.

A roof fall occurred in the 7th south panel at spad No. 2 + 00. Approximately 750 feet long x 20 feet wide x 6 feet high. We moved the unit out of the 7th south panel to the new 6th south panel.

Employee stated he lifted the continuous miner cable & felt pain in his right groin. Operated (surgery) on 8-7-07. Started missing work on 8-7-07.

EE stated he was operating roof bolter machine. EE pushed up-down boom lift lever, boom came down and struck EE on his left leg and knee, causing pain. EE started missing work on 6/17/07, RTW on 7/2/07.

A roof fall occurred in the 1st West sub-panel at spad No. 7 + 00. 110 feet long X 19 feet wide X 5 feet high. Additional roof support: 12 foot cable bolts. Also changed from 5' grouted bolts to 6 foot 3/4" tension re-bar roof bolts.

EE stated a roof bolt broke while being installed into the roof, causing roof bolt plate to come off. Struck EE on his right lower chin, causing laceration requiring 16 stitches. Started missing time 5/31/07-ret'd 6/4/07.

Employee stated he was walking underground, struck his right shoulder against a roof bolt causing pain & numbness. Started missing work on 5-23-07.

Employee stated he was using a sledge hammer to remove a pin holding boom onto roof bolting machine. A piece of steel from pin struck him in upper left arm. He missed one shift. Returned to work on 5-16-07.

Employee stated he was plastering a concrete block stopping with minova plaster---some plaster splattered striking employee in his left eye causing irriation to his eye.

Roof fall occurred in the east sub panel at spad #8 & 50 in the #6 room....40' long & 19' wide x 5 ft high...no equipment or ventilation affected.

Employee stated while getting out of a 486 S&R scoop operator's compartment, he possibly sprained his right ankle and lower leg. Started missing work on 8/29/06.

Employee stated he was retrieving panel bolts for shuttle car panel lid. The shuttle car panel lid fell on employees right foot, causing a fracture to the employees big toe. EE started missing work on 8/15/06.

Employee stated he was bending six foot roof bolts. Felt pain in his right shoulder. Started missing work on 8-8-06.

Employee stated he was lifting 50# bags of rock dust when he felt pain in his back and left leg. Missed two days away from regular scheduled work.

Employee stated he was using a hammer to drive a nail into a curtain board, missed nail, struck left thumb with hammer. Mashed finger. Started missing work on 7-13-06.

A roof fall occurred on the no. 1 unit at spad no. 6+20 in the no. 6 entry, 50 ft long x 18 ft wide x 8 ft high. Rock fall will not be cleaned up. In process of being sealed.

Employee stated he was replacing a lid cover on junction box when his ring finger on left hand was caught between lid and frame of the continuous miner machine. Mashed finger. Started missing work on 7-8-06.

A roof fall occured in the 1st south main #5 entry at spad no. 4 + 90 third x-cut outby working face 60 feet long x 20 feet wide x 8 feet high.

Employee stated he was walking underground, slipped in a wet area and hyperextended his right leg. He felt pain in his right leg and knee. Started missing time on 5/25/06.

A roof fall occurred in the main east main at x-cut # 150 at spad station # 106 + 13 in the # 1 entry. 35 ft. long X 18 ft. wide X 6 ft. high. No equipment involved or ventilation affected.

A roof fall occurred in the 11th north panel in No. 5 entry (supply road) at spad # 3 + 70. 50 ft. long X 18 ft. wide X 6 ft. high. Did not fall on any equipment or affect ventilation. Working section moved on 5/11/2006.

A roof fall occurred in the main east main at x-cut 155 Spad station 109 + 63 in the # 4 belt entry. 55 ft. long X 29 ft. wide X 6 ft. high. No equipment involved, did not affect ventilation. Working section moved on 5-11-2006.

A roof fall occured on 4/25/06. At spad # 106 + 13 in the pillar line 18 feet wide x 25 feet long x 6 feet high outby working section won't be cleaned up. cribbed off

A roof fall occured in the No.3 entry intersection and extending approx. 20 feet into the cross cut between no. 3 & 4 entries...Height 10 feet x length 38 feet x width 18 feet... working section 005-0 mmu... at Spad No. 9753

EE stated he was pulling on continuous miner cable when he felt pain in his left knee, possibly twisted or sprained. Required surgery on 2/24/06, started missing work on 2/24/06.

Employee was disconnecting belt trailer from hitch - dropped trailer on his left foot causing a contusion. Started missing work on 12/3/05.

EMPLOYEE STATED BECAUSE HIS TASK AS A ROOF BOLTER OPERATOR IS BENDING 6'X 3/4" TENSION RE-BAR ROOF BOLTS, BOTH HIS WRISTS, HANDS & KNEES HURT. HE HAS BEEN A ROOF BOLTER OPERATOR SINCE APRIL OF 2005, HE STARTED MISSING WORK ON 11/14/05.

He was lifting roof bolts onto the roof bolting machine when he felt pain in his back. Started missing time on 11-4-05.

EE stated he was lifting and pulling continuou miner cable---felt a sharp pain in his lower left abdomen---a possible strain muscle or hernia---Employee started missing work on 9-29-05 be off work approx. two weeks.

EE stated he was installing roof support---drilling a one inch hole into mine roof with a one inch pinner steel---pinner steel bent---struck ee on his right wrist---a possible fracture to employees right wrist---started missing work on 8-7-05.

EMPLOYEE STATED WHILE REMOVING BELT CONVEYOR TAIL PIECE - HE SLIPPED IN A MUDDY AREA AROUND TAIL PIECE AND FELT PAIN IN HIS BACK AND RIGHT KNEE. HE STARTED MISSING WORK ON 8/2/05.

Employee was drilling a 1" hole into mine roof. Drill steel bent, striking employee's right thumb. Jammed thumb causing pain. Employee started missing work on 6/21/05.

EMPLOYEE STATED HE WAS MOVING BELT FRAMING & STEPPED ON A PIECE OF CONVEYOR BELT, FOOT SLIPPED CAUSING PAIN TO HIS BACK. EE STARTED MISSING WORK ON 6/10/05.

Employee stated he was changing bits on the continuous miner drum, when employee struck bit wrench with a hammer a small piece of steel off the bit wrench struck employee just above his knee, possibly lodging in his femur bone, started missing work on 7-15-05.

EE STATED WAS BUILDING A CONCRETE BLOCK STOPPING, PICKED UP A CONCRETE BLOCK, TURNED AND TWISTED RIGHT KNEE, POSSIBLE STRAINED KNEE. STARTED MISSING WORK ON 04-18-05

EE stated he bent down on his knees, struck his right knee cap on a lump of coal, causing a cracked knee cap. Started missing work on 4-16-05.

EE stated he was supporting the mine roof---installing roof bolts on his knees---reached for a roof bolt felt pain in his upper right leg---a possible pulled strain hamstring.

EE stated he was walking underground, struck his head against the mine roof causing pain to his head, neck and back. Started missing work 2-26-05.

Employee stated he was operating the continuous miner with the remote control, turned and twisted his right knee causing pain to knee. He started missing work 2-5-05.

Employee stated he was shoveling loose coal onto the belt line, as he turned to throw another shovel of coal onto the belt he twisted his left knee, causing pain to left knee. Started missing work on 1-21-05.

Employee stated he was walking underground & struck his head against a roof bolt, jamming his neck. This caused pain to his cervical area of the neck & back.

Employee stated he was walking underground, started to crossover shuttle car cable, tripped over shuttle car cable, causing employee to fall onto his left arm, causing fracture to lower left arm.

Employee stated he was using a belt knife to cut a piece of 42 inch conveyor belt---knife slipped of belt---struck employee's right thigh causing a laceration requiring five stitches.

Employee was dismounting 773 ir bobcat...slipped and fell on his right wrist causing fracture to wrist...fracture required surgical attention by placing three steel pins in ee's wrist

A HIGHWALL FAILURE OCCURRED IN THE UNDERGROUND PIT AREA ON THE WEST SIDE OF THE HIGHWALL. VERY LITTLE ROCK WAS DISLODGED FROM THE HIGHWALL. APPROX. 14 CRACKS APPEARED IN THE SERVICE ROAD NEAR THE TOP OF THE HIGHWALL, RANGING FROM 1" TO 21" WIDE, FOR A DISTANCE OF 381 FEET.

773 BOBCAT MACHINE ACCIDENTLY STRUCK 6" PLASTIC WATER LINE CAUSING 2" PIECE OF STEEL PIPE PARTIALLY DRIVEN INTO THE GROUND TO FALL OVER STRIKING EMPLOYEE IN MIDDLE OF FOREHEAD CAUSING AN OPEN LACERATION REQUIRING SEVEN STITCHES.

HIGHWALL FAILURE OCCURRED IN THE UNDERGROUND PIT AREA ON THE NORTHWEST SIDE OF THE HIGHWALL ~75' LONG X 25' HIGH TO 10' WIDE, CAUSING SEVERAL TONS OF ROCK TO ACCUMULATE IN THE PIT AREA.

EMPLOYEE STATED HE WAS WALKING DOWN THE #3 RETURN SLOPE ENTRY SLIPPED AND TWISTED LEFT KNEE CAUSING A POSSIBLE STRAIN TO HIS KNEE.

EE STATED HE WAS WALKING DOWN MINE SLOP, SLIPPED AND FELL, CAUSING PAIN TO RIGHT GROIN, POSSIBLE STRAIN.

EMPLOYEE STATED HE WAS CUTTING A BELT PIN WITH A PAIR OF SIDE CUTTERS. HAND SLIPPED OFF SIDE CUTTERS STRIKING SIDE OF BELT FRAMING AND ROLLER CAUSING LACERATION TO INDEX & MIDDLE FINGERS LEFT HAND, REQUIRING THREE STITCHES.

EMPLOYEE WAS ASSISTING IN RUNNING SITES ON THE #3 RETURN ENTRY.

A ROOF FALL OCCURRED ON THE NO.1 UNIT IN THE NO.1 ENTRY-AT SPAD NO. 2 & 75, LENGTH 60 FT X HEIGHT 5 FT X WIDTH 16 FT.

EMPLOYEE STATED THAT HE WAS INSTALLING ROOF BOLTINTO MINE ROOF. THE ROOF BOLT BENT AND CAUGHT EMPLOYEE'S INDEX FINGER ON LEFT HAND, BETWEEN ROOFBOLT AND CANOOPY, CAUSING A LACERATION TO END OF FINGER. INJURY REQUIRED SUTURES.

A ROOF FALL OCCURRED ON THE NO. 1 UNIT 001-0 17TH NORTH WEST PANEL AT SPAD NO. 2+75 IN THE NO. 5 ENTRY. 70' LONG X 6' HIGH X 18' WIDE. WILL NOT CLEAN UP.

A ROOF FALL OCCURRED ON THE #1 UNIT INTHE #4 ENTRY-INTERSECTION. LAST OPEN CROSSCUT-35'L X 18'W X 5'H. ROOF FALL WILL NOT BE CLEANED UP.

EE STATED HE BENT OVER TO SHOVEL COAL ONTO BELT. HE FELT PAIN IN HIS BACK.

A ROOF FALL OCCURRED IN THE #5 ENTRY INTAKE AT XCUT #52 IN THE 1ST MAIN EAST. LENGTH 20FTXHEIGHT 4 FTX WIDTH 18 FT ROOF FALL WILL BE CLEANED UP & RESUPPORTED.

A ROOF FALL OCCURRED ON THE NO. 1 UNIT IN THE NO4 ENTRY--2 XCUTS OUTBY FACE OF COAL. 70FT LONG, X 18FT WIDE, X 5FT HIGH. ROOF FALL OCCURRED IN THE 15TH NORTH PANEL--BETW EEN SPAD NUMBERS 3+55 AND 4+10

A ROOF FALL OCCURRED IN THE 15TH NORTH PANEL. BNO. 5 ENTRY AT SPAD #2+95. LENGTH 30' X WIDTH 18' X HEIGHT 6' AT THE FACE OF COAL.

A ROOF FALL OCCURRED ON THE 3RD EAST MAIN PARALLEL OFF 1 ST NORTH MAIN IN THE NO.1 RETURN ENTRY---WIDTH 18 FEET X HEIGHT 7 FEET X LENGTH 40 FEET--FALL WILL BE CLEANED-LIP & RESUPPORTED.

EMPLOYEE STATED HE WAS OPERATIN GROOF BOLTER MACHINE WALKING BACK TO OPERATOR'S COMPARTMENT, ROCK FELL FROM ROOF, STRUCK EMPLOYEE'S LEFT LEG AND ANKLE. CAUSING FRACTURE TO ELFT LEG & ANKLE.

A ROOF FALL OCCURRED AT XCUT 126 1ST PARALLEL MAIN EAST TWO XCUTS INBY SPAD NO 1689. WIDTH 26'LONG X HIEGHT 6' X WIDTH 19'WIDE IN RETURN AIR COURSE.

EE STATED HE WAS OPERATING A ROOF BOLTING MACHINE...DRILLING A HOLE IN MINE ROOF...A ONE FOOT PINNER WRENCH SLIPPED OUT OF DRILL CHUCK...STRUCK EE ON RIGHT HAND BETWEEN THUMB AND FOREFINGER CA USING SPRING TO RIGHT HAND.

EE WAS REMOVING A PIN FROM DUCT WORK ON A 12CM12 JOY CONTINUOUS MINER, DOOR COVERING DUCT WORK FELL ON EE'S MIDDLE AND INDEX FINGERS RIGHT HAND. CAUSING FRACTURE TO BOTH FINGERS, FIRST JOINTS ON BOTH FINGERS ONLY.

A ROOF FALL OCCURRED ON THE #NO. 1 UNIT 001-0--1 X-CUT OUTBY SPAD NO.3 + 70 IN THE NO.2 ENTRY. LENGTH 35 FT X HEIGHT 3 1/2 FT X WIDTH 18 FT. ON CATCHING HIS FINGER BETWEEN THE HOOK AND BATTERY TRAYS.

A ROOF FALL OCCURED IN THE 14TH NORTH PANEL AT SPAD #2 + 20 IN THE NO 4 ENTRY AT THE FACE OUTBY INTO INTERSECTION LAST OPEN X-CUT. LENGTH 30 FEET, HEIGHT 4 FEET, WIDTH 18 FEET.

A ROOF FALL OCCURED IN THE 14TH NORTH PANEL IN THE NO.1 ENTRY INBY SPAD NO 2 + 75. LENGTH 50 FT X HEIGHT 4 FT X WIDTH 50 FT LONG

EE STATED HE WAS USING A HAND HELD TOOL (CHANNELLOCKS) TO PULL A PIECE OF CONVEYOR BELT BACK TOGETHER CHANNEL LOCKS SLIPPED OFF BELT STRUCK EE UNDER RIGHT EYE CAUSING A LACERATION REQUIRING 3 SUTURES/

A ROOF FALL OCCURED IN THE 14TH NORTH PANEL AT SPAD NO. 6+75 IN THE NO.5 ENTRY. LENGTH 120 FT X HEIGHT 5 FT X WIDTH 18 FT.

EE STATED HE WAS SHOVELING SPILLED COAL ONTO THE BELT LINE, WHEN HE LIFTED SHOVEL OF COAL, SOMETHING POPPED IN HIS BACK.

EE STATED HE WAS GETTING OFF 3 WHEELER--A PIECE OF GOB FELL FROM THE ROOF STRUCK EE ON HIS LOWERBACK CAUSING PAIN TO HIS LOWER BACK

EE STATED HE WAS OPENING A BUCKET OF TAR WITH A PAIR OF CHANNEL LOKS CHANEL LOKS SLIPPED OFF WHILE APPLYING DOWNARD PRESSURE CAUSING EE TO JAMMED HIS INDEX FINGER AGAINST SIDE OF BUCKET CAUSIN G FRACTURE TO INDEX FINGER RIGHT HAND.

A ROOF FALL OCCURRED IN THE #3 ENTRY ON THE NO.1UNIT LOCATED 7TH EAST MAIN PARALLEL, HEIGHT 5FT X 18 FT WIDTH X 40FT LENGTH

A ROOF FALL OCCURRED AT SPAD #1+50, 7TH EAST PARALLEL MAIN, LENGTH 75 FEET X HEIGHT 5 1/2 FEET X WIDTH 19 FEET.

A ROOF FALL OCCURRED ON THE NO. 1 UNIT, NO.1 ENTRY--IN THE 7TH PARALLEL EAST MAIN--LAST OPEN XCUT--HEIGHT 80"--LENGTH 40' LONG--WIDTH 18'.

A ROOF FALL OCCURRED AT X CUT 81 ON 4-B BELT LINE IN 2ND MAIN EAST. HEIGHT 7 FT X WIDE 20 FT X LENGTH 20 FT.

A ROOF FALL OCCURRED IN THE 6TH EAST MAIN PARALLEL AT SPAD NO 9+10 LENGHT 30 FEET X HEIGHT 1' TO 4 FEET X WIDTH 18 FEET.

EMPLOYEE STATED HE WAS USING A BELT KNIFE TO CUT A PIECE OF RUBBER BELT. KNIFE SLIPPED AND CUT EMPLOYEE'S LEFT FOREARM REQUIRING STITCHES.

EMPLOYEE STATED HE WAS USING A BELT KNIFE TO CUT A PIECE OF RUBBER BELT. KNIFE SLIPPED CUT EMPLOYEES RIGHT THUMB, REQUIRING SEVEN STITCHES.

EE WAS TRAMMING CONTINUOUS MINER WITH REMOTE CONTROL STATIONED ON BACK OF MINER MINER DIPPED DOWN IN A LOW PLACE CAUSING THE BACK OF MINER TO RISE UP, CAUGHT EE'S LEFT HAND BETWEEN REMOTE CONT ROL BOX AND MINE ROOF CAUSING SEVERAL STITCHES TO EE S LEFT HAND.

A ROCK FALL OCCURRED ON THE NO. 1 UNIT I.D. 001-0 AT SPAD 2 + 80. LENGTH 25' LONG X 4' HEIGHT X 18' WIDTH INTERSECTION.

A ROCK FALL OCCURRER ON THE NO.1 UNIT I.D. 001-0 IN THE NO.3 ENTRY AT SPAD NO.3 & 50 INTERSECTION LENGTH 20 FT X HEIGHT 5 FT X WIDTH 17 FT.

A ROOF FALL OCCURRED ON THE NO. 1 UNIT IN#4 ENTRY AT SPAD NO. 1 + 10 ... L 20, H 4', W 19'.

A ROOF FALL OCCURRED ON THE NO.1 UNIT IN THE NO.4 ENTRY LAST OPEN X CUT LENGTH 30 FT BY HEIGTH 7 FT BY WIDTH 40 FT.

ROOF FALL OCCURRED ON THE #1 UNIT 0001-0 IN THE #2 ENTRY 10' OUTBY FACE. 20'W, 6'H, 20'L. SPAD 35 + 25

A ROOF FALL OCCURRED IN THE 13TH NORTH PANEL IN THE NO. 4 ENTRY 25' OUTBY FACE OF COAL, ONE XCUT INBY SPAD NO. 1+55, LENGTH 70' X HIEGHT 6' X WIDTH 19'.

AN ACCIDENT OCCURRED WHEN THE DIESEL SCOOP ROLLED FORWARD CAGUHT ONE EE S LEFT LEG BETWEEN CONTINUOUS MINER SIDE RAIL AND SCOOP BUCKET CAUSING FRACTURE TO EE S LOWER LEFT LEG.

A ROOF FALL OCCURRED ON THE 001-0 UNIT AT SPAD #2735--70' LONG X 18' WIDE X 6' HIGH---NO INJURIES OR EQUIPMENT INVOLVED.

A ROOF FALL OCCURRED IN THE #4 ENTRY AT SPAD #21+30. LENGTH 20' X HEIGHT 6' X WIDTH 18'.

A ROOF FALL OCCURRED IN THE 5 ENTRY INTAKE AT SPAD 21&30. 25'LX5'HX11'W.

A ROOF FALL OCCURRED IN THE #5 ENTRY (INTAKE AIRCOURSE) AT SPAD #22 + 70---APPROX 5FT HIGH X 20 FT LONG X 20FT WIDE.

A ROCK FALL OCCURRED ON THE SUPPLY ROAD 4 ENTRY AT SPAD NO. 22 & 00 LENGTH 20 FT X HEIGHT 4 FT X WIDTH 23 FT.

EE STATED WHILE BOLTING A HIGH PLACE IN THE MINEROOF A PIECE OF ROCK FELL FROM THE ROOF, STRUCK EE RIGHT HAND CAUSING A CONTUSION TO RIGHT HAND AND MIDDLE & RING FINGERS.

A ROCK FALL OCCURRED ON THE NO. 12 BELT AT SPAD NO. 8 + 45 ... LENGTH 50 FEET X 5 FEET HIGH X 12 FEET WIDE.

APPROX 400' ROLL OF CONVEYOR BELT ROLLE DOFF SUPPLY CAR CAUGHT EMPLLOYEE'S RIGHT LEG BETWEEN TWO SUPPLY FLAT CARS CAUSIGN A CONTUSION TO UPPER RIGHT LEG.

A PALLET OF 6" CONCRETE BLOCKS SLIPPED OFF TOP OF ANOTHER PALLET CONCRETE BLOCK --- CAUGHT EE'S THUMB RIGHT HAND BETWEEN TWO PALETS CONCRETE BLOCK --- CAUSING FRACTURE TO RITGH THUMB.

EE STATED HE WAS SPLICING CONTINUOUS MINER CABLEWITH BELT KNIFE, KNIFE SLIPPED OFF CABLE, CUT EE'S LEFT LOWER LEG, REQUIRING 5 STITCHES.

EE STATED HE LIFTED A 110 VOLT SUMP PUMP, SUMP HOLE BANK GAVE AWAY AND EE FELL CAUSING PAIN IN HIS LOWER BACK.

A ROOF FALL OCCURRED IN THE LAST OPEN X CUT IN THE 4 ENTRY ON THE NO.1 UNIT 001-0 IN THE 2ND PARALLEL MAIN EAST LENGTH 30 FT X HEIGHT 10 FT X WIDTH 17 FT.

A ROOF FALL OCCURRD ON THE NO. 1 UNIT. NO. 2 ENTRY AT LAST OPEN X-CUT IN INTERSECTION. HEIGHT 5'X18'WX18'L.

A ROOF FALL OCCURRED ON THE NO. 1 UNIT--NO. 1 ENTRY IN LAST OPEN XCUT--IN INTERSECTION--HEIGHT, 5'--WIDTH, 18'--LENGTH, 18'.

EE STATED HE WAS BUILDING A CONVRETE BLOCK STOPPING TOP RUN OF BLOCK FELL APPROX. 5 FT STRIKING EE S LOWER LEFT BACK CAUSING A BRUISE.

EE STATED WHILE BUILDING A CONCRETE BLOCK STOPPING HE PICKED UP A CONCRETE BLOCK AND FELT PAIN IN HIS BACK.

A ROOF FALL OCCURRED IN THE 3 SUPPLY ENTRY AT SPAD 1693 IN THE 2ND PARALLEL MAIN EAST. HEIGHT 5 FT X 18 FT X 30 FT LONG.

EE STATED HE WAS HELPING THE MINER OPERATOR CHANGE MINER BITS WHILE THE MINER OPERATOR WAS STRIKING THE BIT WRENCH WITH A HAMMER A SMALL SLIVER OF STEEL CAME OFF HAMMER STRUCK EE RIGHT FOREARM HAD TO BE SURGICIALED REMOVED.

BLACK LUNG CLAIM.

EE STATED HE WAS SPLICING SHUTTLE CAR CABLE WITH A BELT KNIFE, KNIFE SLIPPED OFF CABLE, STRUCK EE LEFT HAND FOREFINGER CAUSING A LACERATION REQUIRNG 8 STITCHES.

A ROOF FALL OCCURRED IN THE NO. 2 ENTRY FACE TEST AREA 2ND EAST MAIN PARALLELS- HEIGHT 6' X LENGTH 50' X WIDTH 18'.

A ROOF FALL OCCURRED ON THE 1ST PARALLEL EAST MAIN AT X-CUT 117 SPAD NO. 1687. LENGTH 50' X HEIGHT 5' X WIDTH 18'.

AN OIL CIRCUIT BREAKER LOCATED ON THE SURFACE CAUSED AN EXPLOSION, CAUSING TRANSFORMER OIL TO PARTIALLY SPRAY EMPLOYEE CATCHIGN HIM ON FIRE CAUSING A 25 PER-CENT BURNS TO EMPLOYEE'S BODY.

EMPLOYEE STATED HE WAS STRIKING CHISEL WITH HAMMER, SMALL PIECE OF METAL CAME OFF PULLING HUB AND STRUCK EMPLOYEE'S LEFT HAND FOREFINGER 3RD JOINT CAUSING SMALL LACERATION REQUIRING TWO STITCH ED AND REMOVAL OF PIECE OF METAL LODGED IN FINGE

A ROOF FALL OCCURRED IN THE 2ND PARALLEL EAST MAIN TEST STATION HEADINGS AT THE NO. 1 STATION. HEIGHT 6 1/2' X 30' LONG X 19' WIDE.

EMPLOYEE STATED HE TURNED TO TRAM ROOF BOLTER MACHINE FORWARD, STEPPED ON LUMP OF COAL TWISTING LEFT KNEE CAUSING TORN CARTILAGE TO KNEE REQUIRING KNEE TO BE SCOPED.

EMPLOYEE STATED HE WAS USING A BIT WRENCH TO PRY A PIN OUT OF TAIL JACK, WRENCH SLIPPED OFF PIN CAUSING EMPLOYEE TO FALL AGAINST FRAME CAUSING LACERATION TO RIGHT EYEBROW REQUIRING 5 STITCHES.

EE STATED HE WAS ENTERING THE OPERATOR'S DECK ONA DOUBLE BOOM ROOK BOLTER. HIS LEFT FOOT SLIPPED, FELL AGAINST FRAME OF OPERATOR'S DECK CAUSING PAIN TO AREA OF RIGHT HIP. EE STARTED MISSING WO RK 11/14/95.

EMPLOYEE STATED HE WAS OPERATING A SCOOP INSIDE THE DECK, TURNED BODY TO LEFT, STRUCK HIS LEFT ELBOW AGAINST THE SCOOP CANOPY FRAME CAUSING SWELLING IN HIS ELBOW.

A ROOF FALL OCCURRED ON THE NO 1 UNIT ;ID#001-0 ON 08-25 -95 APPROXIMATE TIME BETWEEN 2:00PM & 9:00PM LENGTH 30FTXHEIGHT 6FTXWIDE18FT IN THE NO3 ROOM 1 50FT OUTBY FACE OF COAL

A ROOF FALL OCCURRED IN THE 10TH NORTH ANEL IN THE NO. 1 ENTRY AT SPAD NO. 1736. 30'LX19'WX6'H. ROOF WAS BOLTED WITH 5 & 6' FULLY GORUTED ROOF BOLTS.

A ROOF FALL OCCURRED ON THE 2ND EAST PARALLEL MAINS AT X-CUT #112 TWO X-CUTS OUT BY SPAD #1683. HEIGHT 5 FT X LENGTH 30 FT X WIDTH 18FT. IN THE SUPPLY ROAD. NEUTRAL ENTRY.

A ROOF FALL OCCURED IN THE 2ND PARALLEL EAST MAIN SUPPLY ROAD TWO CROSS CUTS OUTBY SPAD NO. 1723--HEIGHT 6 FT X WIDTH 20 FT X LENGTH 35 FT--FALLWAS FOUND BY PAUL COTTON AND MSHA INSPECTOR TERRY CULLEN.

A ROOF FALL OCCURED IN THE 2ND PARALLEL EAST MAIN HEADINGS NO. 3 ENTRY LAST OPEN CROSS CUT IN INTERSECTION--HEIGHT 6' X WIDTH 20 ' X LENGTH 20 FT. ROOF FALL WAS FOUND BY PAUL COTTON ON A MSHA INSPECTOR.

A ROOF FALL OCCURRED AT FACE OF #2 ENTRY IN THE 6TH SOUTH PANEL LENGTH 35 FT X HEIGHT 6 FT X WIDTH 20 FT NO ONE INJURED DID NOT BLOCK VENTILATION--30" CONVENTIONAL ROOF BOLTS WERE BEING INSTAL LED.

EMPLOYEE STATED WHILE ROCK DUSTING A PIECE OF ROCK ROLLED OFF COAL RIB CAUSING PAIN TO EMPLOYEE'S LEFT SHOULDER.

EMPLOYEE STATED HE SLIPPED, FELL AND STRUCK HIS RIGHT ELBOW ON A ROCK CAUSING PAIN TO HIS ELBOW.

EMPLOYEE WAS PICKING UP WATER LINE AND MINER CABLE, TO PULL IT OUT OF THE WAY OF HT EMIENR WHEN HE FELT A SHARP PAIN IN HIS RIGHT HAND AND ELBOW.

INJURED PARTY WAS WALKING THE 4 BELT WHEN A ROCK 2FTX2FTX3IN FELL FROM THE ROOF & STRUCK PARTY ON THE HEAD & KNOCKED HIM TO THE MINE FLOOR

THE SECTION FOREMAN WAS MAKING HIS ROUNDS ON THE #1 SECTION WHEN HE OBSERVED THE #2 INTERSECTION IN THE LAST OPEN XCUT WAS WORKING. HE DANGERED OFF & INFORMED ALL MEN ON THE SECTION OF THE SIT UATION. IT FELL AT 2300 IN THE LAST OPEN INTERSECTION OF THE #2 ENTYR. THE FALL WAS 25' WIDE, 8' HIGH. 42" FULLY GROUTED TENSION REBAR BOLTS WERE BEING INSTALLED IN THIS AREA. XBAR & PROPS SE

THE SECTION FOREMAN WAS MAKING HIS ROUNDS ON THE SECTION WHEN HE OBSERVED THE INTERSECTION IN THE #4 WORKING ENTRY STARTED WORKING. HE DANGERED OFF & INFORMED THE MEN ON THE SECTION OF THE SIT UATION. IT FELL AT 7:15 A.M. IN THE FACE INTERSECTION OF THE #4 ENTRY. THE FALL WAS 25' LONG, 5.5' HIGH AND 18' LONG. 42" FULLY GROUTED TENSION REBAR BOLTS WERE BEING INSTALLED IN THIS AREA.

INJURED PARTY WAS SCOOPING ON # SECTION WHEN HE CAME UPON A CABLE LYING ON THE GROUND. HE GOT OFF HIS EQUIPMENT AND PICKED UP CABLE TO HANG IT WHEN HE TWISTED HIS RIGHT KNEE.

EE WAS ASSISTING ANOTHE MECHANIC WHO WAS DRIVING A PIN IN A CONTINUOUS MINER, WHEN THE PIN SHATTERED STRIKING EE IN THE EYE.

THE 2ND SHIFT SECTION FOREMAN HAD A FALL IN THE #7 ENTRY IN THE LAST OPEN X-CUT. THE CONTINUOUS MINER MADE A 30' CUT IN THE FACE OF THE #7 ENTRY, BACKED THE MINER OUT AND WENT TO THE NEXT ENTR Y. BEFORE THE PINNER GOT IN IT TO PIN IT, IT HIT THE GROUND. THE FALL WAS 30' LONG, 3' HIGH AND 10' WIDE. WHEN 3RD SHIFT GOT THERE, ANOTHER 20' FELL UP TO THE PROPS THAT WERE SET. THE LAST 20

INJURED PARTY WAS GETTING OUT OF DIESEL MANTRIP WHEN HE TURNED HIS ANKLE.

INJURED PARTY WAS LIFTING UP MINE CABLE TO HANG IT OVER HIS HEAD WHEN HE FELT A PULL IN HIS LOWER BACK.

A ROOF FALL WAS DISCOVERED BY THE DAY SHIFT FIREBOSS ON THE 11-8-94 WHILE MAKING HIS ROUNDS. THE MAN WAS IN THE 7TH SOUTH PANEL THE PARALLEL EAST MAIN IN THE 1 SET OF INT ROOMS IN THE 5 ENTRY NO BLOCKAGE OF ANYTHING EVERYTHING OK.

INJURED PARTY WAS WALKING ALONG SIDE THE ROOF BOLTER LOOKING AT THE ROOF WHEN HE ACCIDENTLY STEPPED INTO A HOLE CAUSING HIM TO TWIST HIS LOWER BACK.

IN THE 9TH NORTH PANEL THE PARALLEL EAST MAIN INT HE 1 ENTRY WE HAD A FALL. THE FALL WAS 48 INCH HIGH 18 FT WIDE AND 30 FT LONG. THE FALL WAS ABOUT 140 DOWN IN THE PANEL. THE FALL OCCURRED ARO UND 10:30 A.M. IN THE FACE OF THE 1 PANEL ENTRY 42 INCH FULLY GROUTED GLUE BOLTS WERE BEING USED. SECTION WAS MOVED.

IN THE 9TH NORTH PANEL 0 THE PARELLEL EAST MAIN I THE #2 ENTRY WE HAD A FALL THE FALL WAS 48FT HIGH 20FT WIDE & 30FT LONG THE FALL WAS ABOUT 178FT DOWN IN THE PANEL ENTRY IN THE #2 ENTRY THE F ALL OCCURRED AROUND 9:45AM IN THE FACE OF THE #2PANEL ENTRY 42IN FULLY GROUTED GLUE BOLTS WERE BEING USED SECTION WAS MOVED

INJURED PARTY WAS STANDING BESIDE A SET OF SCOOP BATTERIES THAT WERE BEING SET DOWN ON THE GROUND. UPON CONTACT WITH THE GROUND SOME BATTERY ACID SLOSHED OT OF BATTERY TRAY AND GOT INTO HIS LEFT EYE.

INJURED PARTY WAS CARRYING A BOTTLE OF OXYGEN WHEN HE FELT A PULL IN HIS LOWER BACK

INJURED PARTY WAS RUNNING A PINNER WHEN HE GOT SOMETHING IN HIS LEFT EYE IT TURNED OUT TO BE A PIECE OF ROCK

A FALL OCCURRED ON THE #1 SECTIN AT 10:45 AM THE 9-7-94. THE FALL WAS INT HE #2 ENTRY 100' OUTBY THE FACE. THE FALL WAS 60' LONG, 3 1/2 HIGH AND 17' WIDE. A SLIP WAS DISCOVERED IN THE INTER SECTION. 42" FULLY GROUTED GLUE BOLTS HAD BEEN PUT UP IN THIS AREA.

INJURED PARTY STEPPED OUT OF A SCOOP BUCKET ONTO A PIECE OF COAL AND ROLLED HIS LEFT ANKLE.

A ROOF FALL WAS DISCOVERED BY 3RD SHIFT MINE FOREMAN EE. THE FALL WAS IN THE 5 ENTRY IN A INTERSECTION 210 FT OUTBY THE LAST OPEN X CUT. THE FALL WAS 35FT L 18 FT W AND 3 1/2 FT HIGH. A SLIP W AS PRESENT IN THIS INTERSECTION ALONG WITH A LITTLE WATER 42 INCH FULLY GROUTED CLUE BOLTS HAD BEEN PUT UP IN THIS AREA.

INJURED PARTY WAS WALKING ALONG CHECKING A WATER LINE LYING ON TOP OF THE GROUND OUTSIDE WHEN HE CAME UPON A SMALL DITCH, HE STEPPED ACROSS THE DITCH AND JAMMED OR HYPEREXTENED HIS RIGHT KNEE.

INJURED PARTY WAS RIDING UNIT MANTRIP TO OUTSIDE WHEN THEY PASSED THROUGH A SET OF VENTILATION DOORS. THE DOORS ACCIDENTLY SHUT AS THE MANTRIP PASSED THROUGH CATCHING THE MANTRIP AND COMMING INTO MANTRIP STRIKING HT EINJURED PARTY.

INJURED PARTY WAS STANDING IN A SCOOP BUCKE TIWTH IT NOT RUNNING PULLING BELT UPON A TRAILER IN TEH SCOOP BUCKET, WHEN HE SLIPPED ON THE SLICK SURFACE INTEH SCOOP BUCKET CAUSIG HIM TO SLIP FAL L TO THE GROUND AND TWISTIGN HIS RIGHT KNEE.

INJURED PARTY WAS RIDING UNTI MANTRIP TO UNIT AT START OF 2ND SHIFT. THE MANTRIP MADE A TURN, AT THAT TIME THE OPERATOR DISCOVERED THE BRAKES FAILED AND HE PUT THE MANTRIP IN REVERSE IMMEDIATE LY CAUSING IT TO GO IN REVERSE AND HIT THE COAL RIB BEHIND THEM.

A ROOF FALL WAS DISCOVERED BY THE 3RD SHIFT MINE FOREMAN ON THE 2-2294 AT ABOUT 0230. THE FALL WAS IN THE 1ST SET OF INT. ROOMS OFF THE 3RD WEST PANEL IN BETWEEN THE #5 AND THE #4 ROOM IN THE XCUT. THE FALL WAS 16' LONG, 5' HIGH & 18' WIDE.48" FULLY GROUTED GLUE BOLTS WERE BEING USED AND ADDITIONAL PROPS WERE SET ON EACH END OF FALL.