Scott Pit: 1 muerte registrada Metal/Non-Metal

employee walked down to service truck to get some magnets off back and when EE did EE dropped one and reached down to pick up when EE raised back up EE hit a piece of metal that was hanging from truck and it busted EE's head causing EE to have 2 staples to be in.

Employee was stripping with trac hoe and wall caved in on trac hoe, busting window out, employee's knee was busted along with chin and broken glass cut up employee's hand

Employee filled the water truck up and started back across the street to the hopper to blow it out, EE heard a noise sounding like a tire blew out and the truck started to tilt over to the right and then flipped 3 times, EE passed out for a minute and when EE came to, EE took EE's seat belt off and looked around to see if EE could tell anything leaking EE climb out

Cleaning build up at conveyor, wet muddy conditions. Stepped in soft material twisting, employee sought treatment for knee sprain.

Driving metal pin with sledge hammer. Metal shard broke free lacerating left leg behind knee, stitches required.

Failed to maintain 3 points of contact dismounting excavator on to uneven ground, twisting ankle resulting in minor soft tissue damage.

The miner as installing a belly pan on the D-6 dozier and inadvertently caught left hand in a pinch point. medical treatment stiches in left hand mid palm

On 2/2/2020 the miner reported to the safety supervisor that the miner had fallen while dismounting dump truck on 1/31/2020. Miner stated miner mis-stepped one of the steps causing miner to fall to the ground at a height of approximately 3ft.

A 745 CAT articulating truck tipped over in a curve road conditions were wet. No equipment damage. Employee received medical treatment for bump on head and knee.

Defective tire hammer handle. The damage could not be seen during the pre task inspection of the tool. The miner was breaking down tires with the hammer when the handle broke and the metal end of the hammer bounced off of the tire striking the miner in the right forehead. The miner received stitches for a 6" laceration.

Miner had right hand caught between a flight hub and the wall of the course material washer while performing maintenance on the washer flight hub assembly. The miner and an additional maintenance person was attempting to maneuver the flight hub assembly into place when the miner was injured.

Miner was injured while moving a conveyor. The tail pulley end raised off of the ground slightly picking the miner up and allowing ee to fall about 2 feet back to the ground spraining rt ankle and left knee. Restricted duty case, follow up in a week. Miner may return to restricted duty on 05/25/2017.

Operator upset equipment while dumping load. Operator failed to ensure truck was level before attempting to dump. Truck upset on passenger side. Operator was utilizing their seat belt at the time of the incident. Resulting injury were lumbar, lumbar radius strain. Miner refused medical treatment.

Miner was attempting to turn on water to plant one when stepped on a poisonous reptile. The miner abruptly jumped away, twisting awkwardly pulling or straining lower back.

Miner was conducting repair work on a piece of mobile equipment when employee ducked under the equipment, raised up too soon and struck head on the equipment. Due to the repair location the miner did not have on a hardhat. Miner received stitches for a minor laceration to the top of head.

Operator stated that while operating loader loading outside contract trucks EE pulled or strained back.

Employee was working on a shacker and twisted to get a tool from behind EE and employee stated they felt a pull in lower back.

A panel box door was not properly secured in the closed position allowing water to enter into the electrical panel. The EE opened the panel box to turn on the breaker & the panel face shocked the EE. The shock was minor but the EE was taken to a doc to be checked out. There were no obvious signs of injury. The EE stated EE had minor tingling in EE's left hand.

Miner stepped on compressed airline while attempting to cut off a water line he had used to clean the windows of his equipment. The compressed air line ruptured spraying debris into the miners face and eyes. Miner sustained minor facial lacerations and debris in his eyes.

Employee was attempting to assist a driver with closing his tailgate. Employee used his hands and attempted to pull out on the tailgate so the driver could release the latches and allow the gate to fully close. The gate closed and caught his right index finger between the tailgate and the bed of the truck causing a laceration to employees right index finger.

Miner was lifting a tail pulley and strained his back. It was sunny and dry out.

A mechanic was standing behind his pickup truck outside the office when another employee pulled up behind him in another vehicle. When the other employee shifted his vehicle into park, the vehicle rolled forward pinning the mechanic's leg between the two bumpers.

EMPLOYEE WAS LOADING RAILCARS WITH ROCKS TO BE RAILED TO FLORIDA. HE WAS TRYING TO MANUALLY MOVE A CAR FORWARD TO EVENLY DISTRIBUTE THE MATERIAL WITH A METAL BAR. THE BAR SLIPPED HE LOST HIS F OOTING & FELL BACKWARDS HITTING HIS BACK ON THE RAILCAR.

THE EMPLOYEE WAS SUPERVISING LOADING RAIL CARS VIA PLANT TRUCKS WITH ROCKS. HE STEPPED DOWN TO THE GROUND. THE IMPACT OF HIS LANDING RESULTED IN A PULLED LIGAMENT.

EMPLOYEE WAS CUTTING A BOLT WITH A WELDING TORCH LAID THE TORCH DOWN THEN BACKED INTO IT BURNING HIS LEFT LOWER LEG

EMPLOYEE WAS HELPING PUT HYDRAULIC OIL IN EXCAVATOR HIS FOOT SLIPPED HE FELL & LANDED ON HIS LEFT FOOT & TWISTED IT

WHILE WELDING WIND BLEW A PIECE OF HOT STEEL ON TO EYE OF EMPLOYEE. HOT METAL WAS ON BEAM ABOVE THE EMPLOYEE AND WHEN HE RAISED HIS WELDING HELMET THE METAL FELL INTO EYE.

I.NAME HOOKED SET OF COME-ALONGS IN BOLT HOLE WHICH WASNT LARGE ENOUGH TO HOLE HOOK.THEY SLIPPED OUT WHEN HE WAS PICKING UP ON THEM.CAUSING HIM TO HURT RIGHT ARM,HEAD,LEFT KNEE.

CLIMBING DOWN OUT OF TRUCK AND TWISTED FOOT