TXI-Port Costa Plant Metal/Non-Metal

WHILE CLEANING THE STEDMAN CRUSHER. EE ATTEMPTED TO TURN THE CAGES TO CLEAR BUILT UP MATERIAL. AS THE CAGE ROTATED HIS HAND WAS PINCHED BETWEEN THE CAGE AND PACKED MATERIAL.

EE WAS COMING DOWN WALKWAY FROM PELLET SILOS AND SLIPPED AND FELL INJURING HIS LOWER BACK.

EE WAS INSTALLING A TAIL PULLEY AND STRAINED HIS BACK. NO ONE TO HELP HIM REMOVE THE OLD TAIL PULLEY.

EMPLOYEE WAS PUSHING MATERIAL INTO THE SURGE PILE WITH A FRONT-END LOADER. A LARGE KLINKER WAS IN THE PILE OF MATERIAL. EMPLOYEE CLIBED OFF THE LOADER TO REMOVE IT AND WHEN HE BENT OVER HIS HA RD HAT FELL OFF. WHEN HE RAISED UP TO PUT HIS HAT ON, HE HIT HIS HEAD ON A SUPPORT BEAM.

EE WAS STANDING ON TOP OF THE LOADER'S BACK TIRE ATTEMPTING TPO HEAT UP A GREASE GUN BY PUTTING IT AGAINST THE EXHAUST PIPE. THE TIRE HAD MUD ON IT, HE LOST HIS FOOTING, SLIPPED AND FELL ON HI S BACK--ON THE TIRE--THEN FELL TO THE GROUND. THIS IS CLAIMANT'S DESCRIPTION OF ACCIDENT--NO WITNESS.

EE WAS CLEANING COMPACTED MATERIAL FROM A SILO WITH A PRY BAR. MATERIAL DISLODGED AND FELL, PUSHING THE PRY BAR INTO THE EE'S CHEST.

EE WAS CLEANING A CHUTE. HEAVY STEEL DOOR MUST BE REMOVED TO CLEAN. WHILE REINSTALLING THE DOOR, SHE LOST HER BALANCE AND FELL FORWARD, CRUSHING HER FINGER WITH THE DOOR.

EE WAS CLEANING COMPACTED MATERIAL FROM THE VACUUM CHAMBER OF THE EXTRUDER. HE WAS USING A PRY BAR AND A SHOVEL.

EE WAS WORKING IN THE QUARRY DIRECTING A TRAINEE ON THE SCRAPER. HE PICKED UP A BRANCH STICK TO USE TO DIRECT THE OPERATOR. LATER IN THE DAY HE DEVELOPED SWELLING AROUND THE FACE AND ITCHING. IT APPEARS HE WAS EXPOSED TO POISON OAK OR SOME POISONOUS PLANT OR SUBSTANCE.

EE WAS WORKING INSIDE THE KILN ASSISTING IN POURING CASTABLE AT THE 1 TIRE LOCATION. THE LIFHT WENT OUT AND EE STUMBLED IN THE DARK.

EE WAS WORKING ON A SCAFFOLD (KNEELING POSITION)REACHED OUT TO UNCAP DRAIN PLUG BENEATH THE BAGHOUSE SCREW CONVEYOR, LOST HIS BALANCE AND TUMBLED FORWARD, HEAD FIRST, FALLING 5 FT INTO A PILE OF DUST.

EE HAD BEEN USING AN AIR HAMMER WHILE CLEANING UP AN AREA IN THE RAW PLANT SILOS. HE CLAIMS REPETATIVE MOTION ALONG WITH AWKWARD MOVEMENTS CAUSED A STRAIN.

EE WAS CLEANING THE EXTRUDER. WHEN HE LIFTED THE CONE (IT WAS HEAVY WITH CLAY), HE FELT A PULL IN HIS LOWER STOMACH.

THE EMPLOYEE A MAINTENECE MECHANIC, WAS WORKING ON A REPAIR JOB IN THE LOADOUT AREA OF THE PLANT. THEY WERE MOVING AN I BEAM INTO PLACE WITH A BOOM TRUCK. TH EI BEAM BECAME HUNG-UP ON A CROSS BEAM. EMPLOYEE WAS ATTEMPTING TO FREE IT AND WHEN IT DISLODGED, IT FELL ABOUT SIX INCHES AND STRUCK HIS LEFT FOREARM.

EMPLOYEE WAS CLEANING HOT DUST FROM THE KILN BAGHOUSE SCREW CONVEYOR. HOT DUST FELL INTO HIS GLOVE.

EE STATED THAT HIS BACK WAS SORE THE DAY BEFORE. TODAY WHILE LIFTING A SAMPLE BUCKET HE FELT PAIN IN HIS BACK.

EE WAS LEAVING HER WORK AREA, SLIPPED ON PLASTIC FLOOR MAT AND FELL. EE WORKS IN THE ADMIN. OFFICES OF THE FACILITY.

THE OPERATOR WAS ATTEMPTING TO CLEAR HAR DRY MATERIAL FROM THE EXTRUDER BEHIND THE PUNCH PLATE. HE ADDED WATER TO THE MIXTURE IN THE CHAMBER, BUT THE WET CLAY COULD NOT PUSH THE DRY CLAY OUT O F THE EXTRUDER. THE WET CLAY RECIRCULATED THRU THE CHAMBER, BUILDING UP HEAT AND STEAM. WHEN THE OPERATOR ATTEMPTED TO REMOVE THE GATE TO CLEAN OUT THE MATERIAL, STEAM FORCED THE GATE OPEN.

KILN OPERATOR WAS ASSISTING EQUIPMENT OPERATOR IN CLEARING BACKED UP MATERIAL FROM THE EXTRUDER. OPERATOR OPENED GATE TO EXTRUDER, STEAM AND MATERIAL UNDER PRESSURE WAS FORCED OUT THROUGH GATE AND HIT HIM IN THE FACE.

EE ALLEGES COLLAPSED LUNG DUE TO WORKING IN DUSTY ENVIRONMENT. FIRST OCCURRENCE FROM 3-23-96 TO 4-14-96. SECOND OCCURRENCE FROM 5-9-96 TO JULY 14 1996 RETURNED TO WORK 7-15-96 CLAIMED WORKERS COMP 8-23-96.

EE WAS HOOKING UP A WELDING TRAILER TO THE FORK LIFT. THE FORK LIFT OPERATOR BACKED UP TO THE TRAILER & BUMPED INTO INJURED.

EMPLOYEE WAS ATTEMPTING TO MOVE THE SHOP ANVIL.SHORTLY THEREAFTER HE FELT PAIN IN HIS LOWER BACK.

EE WAS UNPLUGGING THE RECLAIM HOPPER AT THE SCALPING TOWER. THE FRONT END LOADER, DRIVEN BY EE PARKED ON A ROADWAY ABOVE THE EE. HE STOPPED THE LOADER NEXT TO A LARGE CONCRETE BLOCK WEIGHING A PPROX. 500 LBS WHICH IS USED AS A BARRIER IN PLACE OF A BERM WHEN THE DRIVER EXITED THE LOADER HE BRUSHED AGAINST THE STEERING WHEEL. THE LOADER ARTICULATED TO THE RIGHT AND THE BUCKET PUSHED

EE WAS CHANGING A SCREEN IN THE PREP PLANT, CAUGHT HIS FINGER BETWEEN THE EQUIPMENT FRAME AND THE SCREEN.

EMPLOYEE WAS WALKING TO THE JOBSITE THROUGH THE BRICK PLANT HE STEPPED INTO A TRANSFER CAR PIT & FELL

EMPLOYEE WAS CLEANING A RAW SHALE SILO WITH A METAL PRY BAR. HE WAS WORKING FROM OUTSIDE THE SILO THROUGH THE DOORWAY WORKING SHALE LOOSE FORM THE INSIDE WALL. HE STRUCK HIS HAND AGAINST THE D OOR FRAME, CUTTING IT SEVERELY. HE WAS SENT TO MT. DIABLO MEDICAL CENTER EMERGENCY WHERE THEY DETERLMINED HIS RIGHT THUMB WA BROKEN.

EE WAS WASHING OUT THE EQUIPMENT WHEN THE AUTOMATIC DISCHARGE HATCH CAM EDOWN AND CAUGHT HIS HAND AGAINST THE FRAME WORK OF THE EQUIPMENT.

EATING LUNCH IN THE LUNCH ROOM AND FELT FOREIGN BODY IN EYE.

EE DRIVING DUMP TRUCK. DUST BLEW INTO HIS EYE.

UNHOOKING A CHAIN FROM BUCKET OF BOBCAT.

CUT RIGHT KNEE HWILE CUTTING OUT A GASKET.

PULLING WELDER THAT WAS STUCK IN THE DIRT.

PIECE OF METAL FOOF COVER - [2' X 3'] FELL APPROX. 3' & STRUCK EMPLOYEE ON THE HEAD. HE WAS WEARING A HARD HAT - SAID HE WAS FINE. WORKED REMAINDER OF THE DAY & FALLOWING DAY - INCLUDING O/T. WENT TO KAISER ON 3/2 - HIS DAY OFF.

EMPLOYEE WAS CLEANING A CHUTE AT THE RAW SHALE SILO. HE WAS USING A PRY BAR AND HIT HIS HAND AGAINST A METAL GUARD.

EMPLOYEE WAS BUILDING A NEW CHUTE. HAD REMOVED A SECTION OF STEEL DECK. STEPPING IN AND OUT OF HTE AREA WHERE DECK WAS REMOVED HE STEPPED OVER A BEAM. LOST HIS BALANCE FELL HITTING HIS SHOU LDER ON A BEAM.

EMPLOYEE IS PCM SECURITY/TRAFFIC MANAGER ALSO PERFORMS JANITORIAL DUTIES HE HAD OPENED THE GATES AT THE PLANT MONITERED TRUCK TRAFFIC IN CROCKETT TO KEEP TRUCKS FROM ENTERING CROCKETT BEFORE 6 :00AM RETURNED TO THE PLANT & WAS EMPTYING TRASHBASKETS IN THE OFFICES FELT SHARP PAIN IN CHEST & DROVE HIMSELF TO THE HOSPITAL EMERGENCY

SHE WAS CLEANING WITH A METAL BAR-STRUCK HER HAND AGAINST THE CHUTE.

EMPLOYEE FELT FOREIGN BODY IN EYE WHILE DRIVING HOME FROM WORK.

SMASHED FINGER BETWEEN 2 PIECES OF SHEET METAL

EE WAS FASTENING HIS SEAT BELT ON THE L-2 LOADER. THE SPRING ON THE BUCKLE BROKE AND LODGED IN HIS FINGER.

EE WAS LIFTING A GUARD TO CLEAN UNDER A TAIL PULLEY. FELT PAIN IN LOWER BACK.

EMPLOYEE WAS IN THE PROCESS OF LOCKING OUT A PIECE OF EQUIPMENT. HE SLIPPED & FELL ON SOME LIGHTWEIGHT AGGREGATE PELLETS.

EMPLOYEE WAS CRAWLING INTO THE SCRUBBER TANK TO CLEAN DOWN THE MUD AS HE WAS PULLING HIMSELF THROUGH THE MANHOLE HE FELT A PULL (PAIN)IN HIS GROIN

EMPLOYEE EXPERIENCED CHEST PAIN WHILE CLIMBING STEPS TO TOP OF SILOS

EMPLOYEE CLAIMS HE BURNED HIS ELBOW WHILE WELDING. HE DID NOT REPORT THE INJURY UNTIL 6/10 WHEN IT BECAME INFECTED.

WHILE OPERATING THE LOADER - DUST BLEW IN HIS EYES.

EMPLOYEE CLAIMS HE WAS CARRYING HEAVY MATERIALS UP THE STEPS TO THE TOP OF THE SILOS TO DO REPAIRS AND STRAINED HIS BACK.

EMPLOYEE SERVICING FRONT END LOADER PRIOR TO OPERATIOLN BURNED ARM STEAM FROM RADIATOR

TWO MECHANICS WERE WORKING ON THE SAME JOB. WELDING. DID NOT USE SCREEN TOSHIELD OTHER EMPLOYEES.

EMPLOYEE WAS DOING CLEAN UP WORK & FELT A PAIN IN HIS LOWER BACK. EMPLOYEE HAS A HISTORY OF BACK PROBLEMS NOT RELATED TO WORK.

EE HIT HIS FINGER WITH A HAMMER.

EMPLOYEE WAS USING GRINDER ON A PIECE OF STEEL. IT KICKED BACK AND CUT HIS KNEE.

WHILE REPLACING A SCREEN HE FELL INTO A CHUTE-A FALL OF APPROXIMATELY 15 FEET EMPLOYEE SAID HE WAS OK AND DID NOT GO FOR A MEDICAL UNTIL JANUARY 8,1993.HE WAS GIVEN PAIN MEDICATION.

HE WAS HOLDING THE HAMMER DURING THE INSTALLATION OF HAMMERS IN A CRUSHER AND MASHED HIS RIGHT INDEX FINGER.

EMPLOYEE WAS REMOVING PRODUCT FROM THE HOT BELT AT THE EXIT END OF THE ROTARY KILN.A PIECE OF HOT AGGREGATE HIT HIM IN THE EYE.

EMPLOYEE WAS HOLDING A PIECE OF METAL WHILE ANOTHER MECHANIC WELDED EMPLOYEE SAID HE LOOKED WITHOUT WEARING GLASSES OR A HOOD AND RECEIVED FLASH BURNS.

EMPLOYEE AS CLEANING OVERSIZE ROCK OUT OF THE MCCLANAHAN CRUSHER AS HE LIFTED A LARGE ROCK HIS HAND HIT A SHARP ROCK

EMPLOYEE WAS REMOVING ANVILS FROM THE CRUSHER AND FELT A STRAIN IN HIS LOWER BACK. WORKED THE REST OF THE DAY AND FOLLOWING DAY WITHOUT COMPLAINT.

EMPL CARRYING A PART TO MATERIAL WELDING TABLE WHILE ANOTHER EMPL WAS ARC WELDING AND RECD FLASHBURNS TO EYES. ALSO GOT A METAL CHIP IN EYE-LEFT EYE.

EMPLOYEE WAS WALKING ALONG THE 2900 WALKWAY. HIS RIGHT ARM STRUCK THE ROUGH EDGE OF AN ANGLE IRON POST ON THE WALKWAY.

DUST BLEW INTO HIS EYES.REQUIRED MEDICATION.

EMPLOYEE TRANSFERRING A SIPHON HOSE FROM ONE QUARRY SETTLING POND TO ANOTHER. HE SLIPED AND FELL ON THE EMBANKMENT BETWEEN THE PONDS. HE DID NOT FEEL ANY DISCOMFORT UNTIL AFTER LUNCH.

EMPLOYEES WERE ENGAGING IN HORSEPLAY. EMPLOYEE HAD HIS BACK & NECK TWISTED. NOW COMPLAINS OF PAIN IN NECK & SPINE & IS CURRENTLY BEING TREATED BY A CHIROPRACTOR. HE WAS NOT SURE OF THE DATE OF INJURY - APPROX. 3-26-92. [LATER NOTE- NO EVIDENCE THAT INJURY OCCURRED AT WORK]

OPERATOR WAS MAKING ROUTINE CHECK OF EQUIPMENT. AS HE WAS WALKING PAST THE 3240 CONVEYOR BELT ON HIS WAY TO CHECK THE CHUTES, A LARGE PIECE OF MATERIAL STRUCK THE MAGNET AND BOUNCED OF THE CON VEYOR. THE PIECE OF MATERIAL STRUCK HIM ON THE ARM AND KNOCKED HIM TO THE DECK.

EMPLOYEE HAS COMPLAINED OF STRESS DUE TO HIS JOB. CALLED IN ON 1/14/92 TO REPORT HE WAS IN HOSPITAL. WE HAVE NEVER RECEIVED ANY MEDICAL (PHYSICIANS 1ST REPORT) VRIFICATION FROM EITHER TOM'S DO CTOR OR THRU HIM.

EMPLOYEE WAS USING A BAR TO CLEAN A CHUTE AND HIT HIS HAND AGAINST THE SIDE OF THE HOPPER.

INJ PERSON JUMPED ONTO A TEMPORARY DECKING WHICH HAD SHIFTED.THE DECK SHIFT RESULTED IN A HOLE WHICH HE FELL THROUGH TO THE GROUND FLOOR 10'.

EMPLOYEE WAS USING A BAR TO DISLODGE MATERIAL IN ONE OF THE STORAGE SILOS. WHILE DIGGING AT THE MATERIAL HE FELT A SHARP PAIN IN HIS RIGHT SIDE.

EMPLOYEE WAS WORKING AT THE CEMCO, TRYING TO REMOVE A CHUTE. WHILE REMOVING THE GUARD HE STRAINED HIS LOWER BACK.

CUTTING A BOLT WITH A CUTTING TORCH

EMPL WORKING IN QUARRY CLEANING DIRT FROM 2800 BELT IN TUNNEL.WALKING UP INCLINE HE SLIPPED & FELL TWISTING KNEE.

EMPLOYEE WAS PULLING ON AN AIR HOSE TRYING TO GET SOME SLACK FOR THE JACK HAMMER. THE HOSE CONNECTION CAME APART AND STRUCK HER ON THE SHOULDER.

EMPLOYEE WAS DOING CLEAN-UP WORK IN THE LIGHTWEIGHT PLANT. WAS SHOVELING IN A STRAIGHT LEG POSITION.

FOREIGN BODY RIGHT EYE WHILE DRIVING BULLDOZER.

EMPL REPORTED THAT HE STRAINED BACK WHILE LIFTING 25# SPACER BLOCKS FROM BACK OF PICKUP TRUCK.

WALKING DOWN HILL STEPPED ON ROCK TWISTED KNEE

CARRYING AND DRAGGING 150 POUND TAMPER ALONG WITH OTHER EMP

WORKING AT KILN WELDING HOT AGGREGATE SPILLED FELL OIN BOOT

USING WRENCH TO ADJUST CONV

EMPLOYEE WAS CARRYING 5 GAL CONTAINERS OF OIL UP STEPS TO THE 2ND PIER OF ROTARY KILN

INSTRUCTING EMP ON HOW TO ADJUST BELT SCRAPPER JPULLED ON WT IT HIT BELT PINNED HAND AGAINST CHUTE FRAME

FELL WHILE REMOVING GUARD FROM CONV FALLING BACK PUT HAND TO CATCH FALL HOT PC OF KILN GOT IN GLOVE BURNED HAND

EMPLOYEE CLAIMS HE WAS CUTTING ON METAL THAT WAS COVERED WITH LEAD PAINT SAID HE FELT DIZZY NAUSEOUS HEAD ACHY ALSO HE BROKE OUT IN A RASH SUPERVISOR FEELS IT WAS NOT THE CAUSE OF HIS ILLNESS OTHER EMPLOYEES WORKED IN THE AREA WITH NO REACTION

EMPL WATCHING OTHER EMPL CUTTING & GRINDING.NOT WEARING SAFETY GOGGLES AND A PIECE OF SLAG POPPED AND HIT HIM IN THE EYE./

EMPLOYEE WAS GRINDING A GEAR. A PIECE OF SLAG FLEW UP UNDER THE LENS OF HIS SAFETY GLASSES AND PENETRATED HIS EYE.

EMPLOYEE REPORTED PAIN IN HIS ELBOW. COULD NOT RECALL INJURYING IT. FEELS THE SORENESS WAS CAUSED DUE TO THE STIFFNESS OF THE GEAR SHIFT IN THE VACUUM TRUCK WHICH HE OPERATES. EMPLOYEE MAY HAV E ARTHRITIC CONDITION IN HIS ELBOW.

EMPL IS MAINT MECHANIC.WAS REPAIRING DUST SYSTEM.PULLED ON SCREW DRIVE WITH A BAR TO FREE IT UP AND STRAINED HIS BACK.

EMPL WORKING ON AIR BRAKES UNDERNEATH VACUUM TRUCK WHILE MOTOR WAS RUNNING.INHALED EXHAUST FUMES.

HAULING MATERIAL DUST BLEW IN EYE

EMPL WELDING ON ROTARY KILN.ANOTHER EMPL ALSO WELDING AT CLOSE RANGE.EMPL FLIPPED HELMET UP AND RECEIVED FLASHBURN FROM OTHER WELDER.R

EMPL IS MAINT SUPV,WORKING IN FINE GRIND AREA OF PLANT,STEPPED OVER WALL,SLIPPED ON AGGREGATE AND FELL TWISTING ANKLE.NO LOST TIME BUT DID REQUIRE MEDICAL ATTENTION RATHER THAN FIRST AID.

EMPL NOT SURE WHERE INJURED.POSSIBLY WHILE UNDERGOING EVALUATION TO SEE IF PHYSICALLY CAPABLE OF PERFORMING TASKS OF ROTARY KILN OPERATOR.

EMPL IS MAINT SUPT.SMALL PIECE OF SLAG GOT UNDER RING AND PUNCTURED RING FINGER.BECAME INFECTED AFTER SEVERAL DAYS.

EMPL STRAINED BACK REMOVING TOOL BAG FROM TRUCK NO LOST TIME UNTIL 4-26 WHEN HE AGGRAVATED INJURY.

CLIMBING TO TOP OF LIGHTWEIGHT SILO. TWISTED KNEE ON STAIRS.

EMPLOYEE WAS OPERATING THE VACUUM TRUCK. CAUGHT FINGER IN PINCH POINT AT DISCHARGE LEVER.

INJURED EMPLOYEE HAD BEEN ASSISTING A MAINTENANCE MECHANIC.MAINT MECH WAS CUTTING 4" STRIPS FROM A 4'X8' SHEET OF TEFLON.THE INJURED WAS PULLING CUT PIECES FROM THE RADIAL ARM SAW AND STACKING THEM AS MECH CUT THEM.SAW DEVELOPED TRACTION ON A PIECE OF THE TEFLON MATERIAL AND SHOT IT OUT OF THE SAW.THE MATERIAL HIT HIM IN THE GROIN.

EMPLOYEE WAS CHECKING THE FLOW OF MATERIAL. CLIMBED UP ON THE WHISPER VIBE TO CHECK THE HOPPER AT THE END OF THE BELT AND CAUGHT HIS FINGER IN THE VIBRATOR MOTOR.

EMPL STATES HE WAS STRETCHING BELT WITH CABLE PULLER, PULLER BROKE TRAPPING HAND. EMPL WAS WORKING ON V-7 UNIT REPLACING BUCKET ELEVATOR BOLTS.

MECHANIC HAD JUST FINISHED ADJUSTING THE DRIVE BELT ON THE 3450 CONVEYOR AND WAS JOGGING THE MOTOR. HE TURNED TO START THE BELT, I,NAME REACHED IN TO CHECK THE TENSION-THE BELT STARTED UP AND HIS FINGER WAS CAUGHT BETWEEN THE PULLEY AND THE BELT.

EMPLOYEE TURNED TO LOOK OVER HIS SHOULDER AND FELT MUSCLE SPASM IN HIS LOWER BACK AND DOWN HIS LEGS OPERATING FRONT END LOADER

EMPLOYEE WAS CLEANING THE LONG TUNNEL USING A 5 GALLON BUCKET THE HANDLE BROKE BUCKET FULL OF DIRT DROPPED ON HIS RIGHT FOOT

WALKING AROUND PILE OF LIGHTWEIGHT AGGREGATE, SLIPPED & SPRAINED HIS ANKLE.

INSTALLING STARTER ON BRAKER OF ID, INDUCE DRAFT, FAN OF THE ROTARY KILN WHEN THE KILN STARTED UP THERE WAS AN ELECTRICAL FLASH.

EMPL CLIMBED UP3LADDER TO PLATFORM.BUMPED HIS KNEE.

SLIPPED ON WET 8ECK.

EMP OBSERVED SC9EW CONVEYOR OVERFLOWING. HE CLAIMS HE SHUT OFF THE CONTROL REACHED INTO CONVEYOR TO CLEAR IT AND AS HE DID THE CONVEYOR STARTED AND CUT HIS HAND

ATTACHED-CARPAL3TUNNEL SYNDROME CONTINUING SINCE 1-84.

INJURED EMPLOYE9 WAS WORKING ALONG SIDE ANOTHER EMPLOYEE SHOVELING MATERIAL ONTO A CONVEYOR BELT.HIS CO-WORKERS SHOVEL HIT THE CONVEYOR BELT AND WAS FORCED INTO HIS HAND.

ENTERING SILO #5.HE HIT HIS BACK AGAINST THE TOP OF THE PORT HOLE.

EMPLOYEE WAS AS8ISTING MAINT ENANCE PERSONNEL IN REPLACING A BEARING THEY HIT THE BEARING WITH A HAMMER & A METAL CHIP FLEW OFF & LODGED IN I.NAME LEG

EE WAS WORKING 5T HIS REGULAR JOB IN THE PERP PLANT DOING CLEANUP WORK. A LARGE PIUECE OF MATERIAL CAME OUT OF A CHUTE & HE WAS ATTEMTPTING TO BREAK IT UP WITH A BAR. WHEN HE HIT THE PIE CE TO BREAK TI 6P THE BAR SLIPPED & HE HIT HIS HAND AGAINST THE CORNER OF AN ELECTRICAL BOX & CUT HIS FINGER.

INJ EMP WAS ATT9MPTING TO REPLACE A SCREEN GUARD ON TAIL PULLEY WHILE BELT WAS RUNNING GUARD CAUGHT IN THE BELT AND WAS PULLED FROM HIS HAND SKIN WAS TORN FROM HIS FINGER TIPS - RIGHT HAND

EMPLOYEE WAS LI0TED UP IN THE BUCKET OF BOB CAT TO UNPLUG A PIPE. WHEN HE HIT THE PIPE TO CLEAR IT DUST POURED OUT OF THE PIPE, HE STEPPED BACK, INSTRUCTED THE OPERATOR TO LOWER THE BUCKET. HI S HEEL WAS CAUG2T BETWEEN THE BUCKET AND FRAME OF THE BOBCAT. HIS HEEL WAS CUT- REQUIRED STITCHES.

ANOTHER EMPLOYE9 WAS PULLING A LIGHT ATTACHED TO A CORD THROUGH THE HATCH AT THE TOP OF THE PELLET SILO.THE CORD DISLODGED A PIECE OF MATERIAL ANS IT FELL TO THE BOTTOM OF THE SILO AND HIT MS. I NAME ON THE H5RD HAT.SHE WAS CLEANING THE PELLET.

EMP CLAIMS HE W5S CLEANING BETWEEN THE ROLLERS ON CONVEYOR BELT AND HOT HIS ARM CAUGHT IN THE CONVEYOR

SLIPPED AND FEL5 ON A PIECE OF AGGREGATE

EMPL LIFTING SA7KS OF CASTABLE

EMPLOYEE WAS PULLING CONVEYOR BELT UP TO PELLET SILO.