Buscar en el registro

Employee was unloading belt structure and pulled a muscle in their back.

Employee went to pull cable bolt on ground to put into roof. Cable bolt was hung on a pile of coal and when ee snatched it hard ee felt a pop in left shoulder.

The employee smashed left pinky finger between a steering jack and the mine roof. The finger was fractured and employee received 10 sutures.

EE was building an intake brattice, when EE felt EE's shoulder pop.

While loading a car employee stepped on a mound of coal and twisted their left knee.

Employee was straitening bolt back to install in roof when they felt a strain in the left shoulder and elbow.

Employee was taking a loop of cable off the miner and felt pain in back

Employee was helping hang the miner cable in #8 entry when EE felt something pop in the right shoulder.

Employee bent over to pick a miner bit and felt pain in lower back

The employee was pulling down a curtain that was hard to take down, when it came down, EE injured left shoulder, also causing pain in the neck, left arm and hand.

The employee was bending two roof bolts at the same time, and strained their shoulder.

Employee was lifting the lid of a ramcar battery when it slipped out of right hand smashing ring finger and middle finger on left hand.

Employee was pulling bolter cable and felt a dull pain in lower right back.

EE climbed up on ladder of Komatsu 785 Haul Truck to inspect and secure a block heater receptacle that was broke off. When climbing back down off of the truck EE strained lower back. EE finished the shift and did not report injury till 1:00 pm on 7/25/2017.

Employee was replacing grizzley flume screen when their hand slipped catching their right forearm on the rib on the grizzley causing a puncture to forearm. They received stitches and returned back work.

Employee was repairing doors at a rock dust hole when a beam turned over and caught their right little finger, mashing and broke it. This resulted in five stitches to employee's right little finger.

While closing mandoor, employee's right middle finger was caught between the door and door frame, pinching, resulting in sutures.

Employee was pulling drill steel out of roof, when they felt a pain in their back and twisted their knee. Employee did not miss work until 05/08/2017.

The employee strained employee's back while replacing the ripper shank guard on a D-11 dozer.

The employee stated: that they were tearing down old concrete block airlock on the 4-a belt. Employee was picking up a block, when a block that was stuck to the roof with plaster, suddenly fell hitting employee on the left hand

EE was hanging an A-Frame and was holding it up with left knee. The A-Frame slipped off the stud and came down on EE as EE fell their right foot did not turn when their body twisting their knee. EE was treated at Muhlenberg Community Hospital and diagnosed with a fracture to the right medial tibial plateau.

Employee was cribbing up the bumper of miner. The miner sit down on the end of the crib block, causing the other end of the crib to strike employee in the chin, causing a laceration.

The Employee stated: that EE was bending a roof bolt on a flat surface, the roof bolt twisted around while EE was bending it and EE felt a strain on the right side of EE's lower back.

Employee lifted a 7' timber twisted around felt a sharp pain in the middle lower back, resulting in a strain. Employee was at x-cut 25 on the Main North Supply Road.

Employee stated; was unloading 20ft sections of 4 inch fresh water line on #2 unit. Employee was working alone when they stated that they felt pain in their lower back on the left side.

3 individuals were in the process of replacing the lid on the power center. The injured person was on one side of the lid and the other two were on the opposite side of the lid. As they were placing the lid in place two of them accidentally dropped their end. The injured employees hand was underneath allowing the lid to land on left index finger.

Employee Stated: EE was building a brattice. EE turned around in a twisting motion and bent over, picked up a block and raised up turned around and felt a pain in lower back on the right side.

EE states got off ram car to remove flagging and to make sure it was safe to travel through cross cut and while getting back in car felt pain in lower back.

Finger caught between segment of vibrator screen and frame of vibrator as it was being removed.

Employee states while bending 5 foot roof bolt in hole EE's body was not square and bolt shifted causing pain to right shoulder.

Employee states while stacking block brattice, EE didn't cap and while turning to get cap boards the brattice fell striking EE on foot and lower leg on right side.

Emloyee states after pinning an entry started loading bolter. While loading pie pans for skin control 20-30 slid back cutting forearm resulting in stitches.

Employee states was pulling a dumpster with Dapco EE had a chain get caught under skid and attempted to jerk the chain out and felt burning pain middle lower back

Building a brattice picked up a block to stack on the brattice, turning around and felt a pop in EE's middle lower back

Employee was going into the right return. When he opened the man door he was blown thru the door causing an injury to his lower back and right leg. This wasn't a lost time until 1/07/2015.

Employee was dropping his miner cable, when he raised up tie wire went between his glasses and scratched his eye.

While unloading 6" polly pipe from semi-truck a piece of pipe became lodged and as employee walked up to side of truck the pipe became free hitting him in thigh. His foot was wedged in between two pieces of pipe already on ground, as he was knocked over by the force of the falling pipe.

Employee stated he was closing airlock door at the mouth of # 1 unit and timber worked loose and door fell striking him on his left hand on ring finger cutting at first joint of finger. Took to Ohio co. ER and received four stitches

Employee was on #3 unit entry #7 working on the pre-dump of double boom fletcher roof bolter. Employee told the operator to try the pr-dump. As employee was getting up off the mine floor he became off balance and grabbed the pr-dump with his left hand and the pre-dump closed on it resulting stitches to his middle finger and index finger.

Employee was hanging continuous miner cable on #2 unit in #6 entry and strained his back.

Employee stated: was moving power on #2 unit and was in #6 entry moving power cables. There was mud and water in this entry and was dragging cables thru this area resulting in straining right side of lower back.

Building overcast went to grab a piece of metal and the whole stack fell on top of employees knee/leg.

Employee stated: Installing top Roller belt framing on the #4 unit entry #4 when thumb on the left hand became caught between the framing and the rope resulting a fracture to the end of the left thumb.

Employee stated: was moving belt air lock on #3 unit entry #4 while bending over to pick up timber felt lower back knot up and could not straighten up.

Employee was in the plant thickner tank helping clean out mud when he pulled on a pump hose to reposition it. The hose was stuck in mud and was hard to move. He started having lower back pain after he went home. Employee missed his first scheduled day of work on 7/6/2015.

Employee was in the shop on the surface bending a piece of metal in the bending press. While bending a piece of metal, the metal broke and struck right index finger resulting in a laceration in the bend of the finger. Employee received five stitches.

Employee was on #4 unit entry #5 working on the Feeder. He put pin in the cat assembly and removed come along off the cat assembly. They lowered the cat assembly with the hydraulics of the feeder and as the assembly was coming down the cat caught the tip of the hook and slip off striking him in the mouth and busted one tooth.

EE was on #3 unit supply road loading old pallets onto a trailer. EE picked pallet up and twisted to throw pallet onto the trailer which resulted in a strain to the lower left side of his back.

Injured employee stated he was loading supplies onto the roof bolter and pulled a muscle in his lower back.

Employee was shoveling belt at the 1C Header, when he felt a pain in his back. He did not report this incident until 03/11/2015 and brought in a doctors excuse missing today (03/30/2015)