Buscar en el registro

Employee was lifting a heavy component using his boom, when the chain he was using slipped off mashing his right ring finger. Required stitches.

Employee was putting drive line bolts back in a 980G loader. The rachet slipped off the bolt head, striking the employee on the left side of his nose and corner of his left eye. (stitches)

Employee was putting a wear plate on bottom of 994 loader bucket using a pry bar to lift the plate. The bar slipped, mashed right hand.

Individual was pulling on a wrench in order to loosen a bolt when he felt a "pop" in the neck / shoulder area.

Employee was using 2 come-a-longs to align the top plate of the carousel so it could be welded. One of the come-a-longs slipped while employee's hand was under the plate and mashed his right ring finger requiring seven stitches.

Employee was blocking up loader to fix flat tire, used a metal strip, this strip came out when the loader set down striking the employee in his chest and bottom of his chin.

EE was using a pry bar to align the push-arm of a dozer, he felt pain across his left shoulder down to his thumb.

Employee was raising major bogie using a come-along to install rollers. The come-along slipped, allowed the bogie to fall mashing his left hand between the bogie and the dozer frame.

Employee using come-along, both hooks were pulled open. The force released caused him to smash the end of his little finger on his right hand. Required surgery and two stitches.

EMPLOYEE WAS PRYING ON A RETAINING RING. THE BAR HE WAS PRYING WITH SLIPPED OFF HITTING THE EE OVER HIS RT. EYE, CAUSING A CUT THAT REQUIRED (5) SUTURES.

EE working on a pump wrench slipped and hit him above the right eye making a small cut. Required sutures. EE did not miss work.

EMPLOYEE WAS USING A 12 LB SLEDGE HAMMER WHILE WORKING ON AN UNDERCARRIAGE. HE EXPERIENCED A SHARP PAIN IN HIS LOWER ABDOMEN.

Employee was standing on two hydraulic hoses tightening a bolt when the extention to his wrench broke causing him to fall. He caught himself with his left arm, causing him to injure his left shoulder

REMOVING RADIATOR OUT OF MACHINE STANDING ON LADDER WITH PRY BAR WEDGING RADIATOR OUT OF SOCKET, PRY BAR SLIPPED OFF RADIATOR. STARTED FALLING OFF LADDER, TURNED & JUMPED TO PREVENT FURTHER IN JURIES, LANDED ON LEFT LEG, BRUISING FOOT & KNEE.

EE STATES HE WAS PUTTING FUEL INE ON TRUCK ENGINE WHEN THE WRENCH SLIPPED STIKING RIGHT HAND.

EMPLOYEE WAS PULLING ON A WRENCH TO LOOSEN A BOLT WHILE WORKING ON A DOZER. HE FELT A PULL IN HIS LOWER BACK ON THE RIGHT SIDE.

EE WAS WORKING ON A MINOR BOGIE & ROLLER ON D-30DOZER THE BOGIE SHIFTED FROM ITS POSITION ON THEHYDRAULIC JACK. THIS PINNED THE EE HAND BETWEEN THE GROUND AND THE AIRGUN. THE EE CUT HIS FINGER AND REQUIRED STITCHES.

EE WAS REMOVING TRANSMISSION FROM A D-11 CAT DOZER, KNOCKING A PIN OUT WITH A SLATE BAR. WHEN THE PIN CAME OUT, COUNTERWEIGHT MOVED CATCHING END OF BAR. BAR CAME AROUND AND HIT HIM IN THE JAW. HE BROKE HIS RIGHT JAW AND REQUIRED SURGERY.

EE WAS HELPING MECHANIC AND USING A HAMMER AND CHISEL... GOT A PIECE OF METAL IN HIS RIGHT EYE.

WHILE WORKING ON A 992G TOP BOOM PIN, LINING THE PIN UP TO INSTALL IN THE BEARING, EMPLOYEE FELT A "POP" IN HIS RIGHT WRIST.

EE WAS TAKING DRAIN PLUG OUT OF A 988 WHEEL UNTI USING BREAKER BAR AND SOCKET. THE PLUG WOULD NOT COME OUT SO EE WAS HITTING THE BAR WITH A HAMMER TO HELP LOOSEN IT, STRUCK HIS FINGER WITH THE HAMMER.

EMPLOYEE WAS CUTTING A 5 GALLON BUCKET WITH A RAZOR KNIFE AND THE RAZOR SLIPPED AND JABBED HIM IN THE RIGHT THIGH. THIS REQUIRED 4 STITCHES.

EE WAS HELPING ANOTHER DISASSEMBLE A JACK ON A DRILL. THEY WERE BOTH PULLING ON A PIPE WRENCH WHEN THE WRENCH SLIPPED AND EE PULLED HIS BACK.

EE WAS USING A SLAP HAMMER ON THE DOZER BLADE HE WAS WELDING ON TO KNOCK OFF THE METAL THAT WAS LOSE A PIECE OF SLAGG METAL CAME OVER THE TOP OF HIS HELMET INTO HIS EYE.

EE WAS CLEANING WELD SLAG WITH A WIRE BRUSH AND SOMETHING HIT HIM IN THE LEFT EYE.

EMPLOYEE PICKED UP A TONG WRENCH THEN TURNED AND WRENCHED HIS BACK. HE FELT SEVERE PAIN IN LOWER LUMBAR SECTION.

EMPLOYEE WAS SETTING A D11R ENGINE USING A PRY BAR TO MOVE THE ENGINE OVER WHEN THE BAR SLIPPED AND STRUCK HIS HEAD ABOVE THE RIGHT EYEBROW.

CUTTING CABLE WITH HAMMER TYPE CABLE CUTTER, A PIECE OF METAL CHIPPED OFF CUTTER AND HIT EMPLOYEE IN LEFT INNER THIGH. CHIP WAS EMBEDDED ABOUT 4".

WHILE DRIVING A BEARING IN A BLADE PIN BOSS, EMPLOYEE HAD A PLATE ON TOP OF THE BEARING AND WHEN HE STRUCK THE STEEL PLATE WITH HAMMER A PIECE OF METAL CAME OFF AND PENETRATED HIS ARM.

EMPLOYEE WAS CHANGING TEETH ON A LOADER BUCKET. ANOTHR EMPLOYEE WAS DRIVING THE RETAINING PIN WHILE EE HELD THE TOOTH IN PLACE. THE PIN SHOT ALL THE WAY THRU STRIRING THE EMPLOYEE ABOVE THE LEFT EYE. THE EMPLOYEE RECEIVED SIX STITCHES TO CLOSE THE CUT.

WAS REMOVING RADIAL ROD FROM REFUSE AFTER USING HAMMER AND PIPE WRENCH AND MASHED FINGER WITH HAMMER. DID NOT GO TO DR UNTIL 5-7-99 AND WAS DIAGNODE WITH FRACTURE OF LITTLE FINGER, RETURNED TO WORK W/ NO RESTRICTION.

EMPLOYEE PICKED UP SLEDGE HAMMER TO HIT LOADER BUCKET SHANK AND HAD A SHARP PAIN IN HIS GROIN AREA.

EE WAS CUTTING A SECTION OF WIRE ROPE FOR HIS AUGER, AS HE STRUCK THE CUTTING DEVICE WITH A HAMMER FRAGMENTS SPLINTERD OFF, LODGING IN THE PALM OF HIS LEFT HAND. SURGERY WAS NEEDED TO REMOVE THE EMBEDDED METAL. 10 STITCHES WERE REQUIRED TO CLOSE THE INCISION CREATED DURING SURGERY

HELPING WITH MAINTENANCE ON DAY SHIFT(REGULAR EVE SHIFT EE)USING PINCH BAR TO MOVE 75HP MOTORFELT PAIN IN LOWER BACK. WENT TO SEE DR ON 8/11/98 AND RETURNED TO WORK RESTRICTED SAME DAY

EE WAS USING A SLATE BAR TO HELP INSTALL TRACK ON D11N CAT DOZER. THE BAR SLIPPED AND CUT HIS RIGHT HAND IN THE PALM AREA. THE CUT REQUIRED 7 STITCHES HE HAS LOST NO TIME OVER THIS ACCIDENT.

WHILE HOISTING METAL CHUTE, LEFT HAND WAS CAUGHT BETWEEN CHUTE AND METAL BRACKETS.

EE WAS ASSISTING BLASTING CREW BY BACKFILLING DRILL HOLES WITH A HOE. THE EE STATED THAT HE BEGAN TO FELL TIGHTNESS IN HIS LOWER BACK AND NUMBNESS IN HIS LEGS.

EE WAS TIGHTENING A BOLT ON THE TRACK OF A D-6 DOZER, IT FELT SOMETHING IN HIS LOWER BACK PULL. HE TOLD THE FOREMAN HE WAS OK. HE IS NOW OFF FROM WORK AS OF FEB 17 1997 BECAUSE OF THIS ACCIDEN T.

EE WAS REMOVING COUNTERWEIGHT FROM D11R TRACTOR USING SIX-FOOT BAR TO TAP PIN OUT OF BORE WHEN PIN CAME OUT OF BORE, COUNTERWEIGHT SHIFTED CAUSING BAR TO "KICK-BACK" AND STRIKE EE IN RIGHT SID E OF FACE.

EMP PRYING ON IDLE BELT ROLLER (LINING BELT ON ROLLER) WITH PRY BAR. BAR SLIPPED ODD ROLLER AND FORCED LEFT HAND INTO ELECTRICAL CONDUIT CAUSINGCONTUSION TO LEFT KNUCKLE ON LEFT HAND.

EE WAS BUSTING A LARGE ROCK ON BELT WITH A SLATE BAR. HIT ROCK A GLANCING BLOW AND END OF BAR STRUCK HIS RIGHT EAR LOBE.

EMPLOYEE WAS WORKING ON 777 TRUCK ON TYROD END. HIT END WITH HAMMER, PIECE OF METAL FELW IN LEFT EYE.

WAS CLOSING CAR DOORS, HAD COME ALONG HOOKED TO CAR DOOR TO PULL TOGETHER. HOOK BROKE, STRIKING VICTUM OVER LEFT EYE.

EMPLOYEE WAS WORKING WITH A COME-A-LONG DEVICE WHILE SPLICING A BELT. THIS DEVICE SLIPPED CAUSING CHAIN TO PINCH HAND(LEFT HAND).

EE WAS USING A SLEDGE HAMMER OT DRIVE IN A PIN ON HE HARD-BAR OF A D-11-N DOZER. A PIECEOF MEDAL CHIPPED OFF OF HTE PIN HITTING EE ONT HE RIGHT SIDE OF HIS FACE JUST BELOW THE BOTTOM RIM OF H IS SAFETY GLASSES MEDAL HAD TO BE REMOVED, REQIURED TWO STITCHES.

PUTTING ON A TOOTH TO THE LOADER BUCKET HIT THE LOCKING PIN WITH A SLEDGE HAMMER A PIECE OF METAL CHIPPED OFF GOING INTO EMPLOYEES RT LEG JUST BELOW THE KNEE

HAND SLIPPED FROM SHOVEL STRIKING RAGGED PIECE OF METAL

EE WAS PULLING THE REAR TANDEM AXLE UNIT WHEN THE LAST BOLT WAS LOOSENED THE WEIGHT OF THE AXLE SHIFTED CAUSING THE DIFFERENTIAL TO FALL TO THE GROUND PINNING EE'S HAND BETWEEN THE GROUND AND THE DIFFERENTIAL

54736YEE WAS TRYING TO RAISE SAND GATE ON FROTH CELLS BY PRYING UPWARD WITH SLATE BAR. THE SLATE BAR SLIPPED AND STRUCK EMPLOYEE UNDER CHIN. LACERATION- SUTURES.

CHANGING STEEL, BREAK-OUT WRENCH JAMMED, OPERATOR TRIED TO UNJAM THE WRENCH USING HIS LEFT HAND. THE WRENCH CAME LOOSE MASHING THE OPERATOR'S LEFT INDEX FINGER BETWEEN THE WRENCH AND A METAL STOP CAUSING A LACERATION REQUIRING ELEVEN (11) STITCHES.