Buscar en el registro

Miner was cutting a belt using a box blade and cut self.

While cutting flashing, accidentally cut left hand with a razor knife.

Miner was welding with a welding hood/shield on. When EE was done, EE removed EE's hood and began to knock extra slag off with a hammer. When EE struck the weld a shard projected back and struck EE's eye. EE did not feel this until several days went by and did not go to the doctor until 7/1/2025.

While tightening a toggle bolt on jaw crusher, the bolt sheared off causing the wrench to spin and struck finger. Laceration to finger needing stitches.

Coworker was using a bar to loosen a piece of stuck material on the floating conveyor. When they struck the material with the bar a small piece ejected and embedded into employee's left forearm. Will need surgery to be removed - pending!

Experienced pain while using hammer to remove a stuck bolt during maintenance task

After lifting an oversized rock from a jaw crusher, the rock was placed on the ground. Upon placement it rolled a quarter turn causing the lifting strap to lay across the employees hand which was resting on the handrail.

Miner was cutting a 1 1/2" rubber water hose for the mud classifier when the knife EE was using slipped and cut the tip of EE's finger. No bone was amputated, however the piece of skin from the tip of EE's finger was removed.

Miner was working to free a motor that appeared seized. The pipe wrench being used to spin the sprocket broke loose, smashing the Miners right ring finger. Laceration was vertical from the front of the finger, over the top and down the back side. The miners fingernail was removed and 7 stitches were used.

Miner was shoveling under locked out conveyor in a tunnel with a spade shovel and had employee's right hand on the but of the shovel. When bringing arm back, Miner struck side of tunnel and pinched right pinky finger, removing skin from end of finger, requiring medical attention.

Miner was replacing a teeth on a excavator bucket. One tooth was stuck so miner used a hammer to loosen the tooth from the shank. When struck a small piece of the tooth broke off and struck the miners right forearm causing a puncture wound.

Worker was taking turns with other workers swinging 20lb. sledge hammer to tighten nut on HP-4 crusher cone. Each worker was swinging about 10 times and switching off. This was EE's second time swinging and he made about 8 out of the 10 swings they were making. He stopped and said he felt his back strain. There were 5 miners taking turns.

Employee was under the pontoon, on his back, in a ditch, tightening dredge bolts to 200 ft. lbs. torque. Employee has right shoulder issues. THE EMPLOYEE DID NOT SEEK MEDICAL ATTENTION UNTIL 1/10/12 WHEN HE SAW A CHIROPRACTOR.

Worker was installing a tooth onto the shank of a loader bucket. In order to align the pin the worker tapped on the tip of the tooth with a steel hammer. While doing that a piece of the tooth chipped off and struck the worker in the abdomen. He went to the doctor and they found that the metal chip had went through his coveralls and shirt and was embedded in his abdominal wall.

Swinging a sledge hammer knocking rocks loose

Miner was doing maintenance work and decided to assist another miner to move a Lower concave ring. The injured miner placed the end of a 6' pry bar onto a hole in the concave ring. As he attempted to move the ring, the bar slipped and the miner fell to the ground spraining his right ankle.

Worker was changing a tail pulley on a conveyor. He was using a 2-lb. hammer to align the equipment. The worker raised the hammer slightly and felt something in his lower back.

Miner was tightening 5/8 inch bold with ratchet wrench. ratchet slipped off bolt and miner struck right #5 finger on conveyor framework.

Worker was using a razor knife to cut a piece of conveyor belt. Worker lost control of tool and inflicted a 5cm cut to his left forarm.

The miner was using a 6' pry bar to apply pressure to a part. The bar slipped & the miner fell to a sitting position. There was a 2" vent cap sticking up. The cap struck the miner on the tail bone. On 06/19/2006 the miner told a supervisor he felt he should see a doctor. We imediately conveyed him to see a doctor.

While perfoming maintenance and tightening a bolt the wrench slipped and employee's wrist struck an angle iron. The metal contacted his right wrist between his long sleeve shirt and his glove causing a small 1/2 inch laceration.

Employee was cutting a piece of rope with a razor blade knife that slipped and cut his right arm

CUTTING COVER OFF S.O. CORD. KNIFE SLIPPED, CUTTING FINGER.

EE WAS PRYING A LARGE ROCK WHEN BAR SLIPPED & HETRIED TO STEP BACK & HUNG UP HEEL & FELL BACK ONTAILBONE & LEFT WRIST. HE FELL 18"TO 24"

CLEANING OFF ROCKS ON TOP OF A GRIZZLY ON TOP OF A FEEDER ABOARD A DREDGE. HITTING A ROCK WITH A SLEDGE HAMMER. ROCK BROKE & HIT LEG.

EE WAS USING A PRYBAR TO DISLODGE CHUTE IN CRUSHER FEEDER.

HOLDING A WRENCH. WRENCH SLIPPED AND SMASHED RIGHT THUMB BETWEEN WRENCH & CAT DRIVE SEGMENT ON DREDGE.

DIGGING TRENCH WITH SHOVEL UNDER ELECTRICLA TRAILER IN BENT OVE POSITION, WHEN A SHOT OF PAIN WENT THRU LOWER BACK, RIGHT HIP AND DOWN RIGHT LEG.

EMPL WORKING WITH SLEDGE HAMMER AND WRENCH.HIT FINGER WITH SLEDGE HAMMER.

CUTTING BUCKET WITH KNIFE, IT SLIPPED CUT LEG

HAMMERING A PIN OUT OF CUTTING EDGE AND HIS LEFT HAND WAS STRUCK BY A METAL FLAKE.

AGGRAVATION OF PREVIOUS INJURY ON 6-29-90.

THERE WAS A ROCK STUCK IN THE FEEDER DOORWAY WHICK BLOCKED PIT RUN FROM COMING DOWN. I PRIED ON THE ROCK WITHA BAR WHICH WE USED FOR THAT PURPOSE, AND GOT SHARP PAIN IN LOWER BACK, WHICH THEN BECAME NUMB DOWN ENTIRE LEFT LEG. EMPLOYEE MISSED 6 1/2 HOURS WORK ON 6-29-90.

TIGHTING BOLTS ON CRUSHER, WHEN WRENCH SLIPPED IN HAND CAUSING ME TO HIT MY KNUCKLES. CUT RIGHT MIDDLE FINGER REQUIRING STITCHES.

WHILE TIGHTENING BOLTS ON DRAGLINE,HE COULD NOT STAND UP WITHOPUT HELP.HE HAD DONE NOTHING WRONG IN THE WAY HE WAS WORKING,THIS IS A REOCCURENCEOF ANOTHER INJURY.

RIGHTENING BOLT ON CRUSHER WHEN WRENCH SLIPPED CAUSING ME TO TWIT MY SHOULDER.

TIGHTENING AGGREGATE DRAIN PLUG WITH PIPE WRENCH DURING WHICH I EXPERIENCED EXTREME PAIN IN LOWER BACK & HIP

PERSON WAS TRAMMING COAL MACHINE GOT LEFT ANKLE CAUGHT BETWEEN COAL RIB AND FRAME OF MACHINE BRAEKING LEFT ANKLE

BEATING ON HOPP9R WITH HAMMER AND HIT ELBOW ON THE HOPPER