Buscar en el registro

Employee was repairing a tire for a skid steer loader using a pry bar when he felt a slight pain in his stomach. The employee did not report the injury until two days after it occurred and did not feel he needed medical attention. Two weeks after the injury he went to the doctor and was told he had an abdominal strain.

Employee was using a metal rod to loosen material in a hopper when his right index finger struck the edge of an i-beam support causing a laceration on his knuckle.

Employee was tightening structure bolts with another employee using torque wrench. Injured employee was using a backup wrench. The employee using the torque wrench asked IE if he was ready & he said yes. The torque wrench began to tighten and the back up wrench mashed his thumb against steel.

Maintenance Tech was hammering a plate that was just welded. When he struck the plate, a piece of slag flew into his eye.

Employee was working on a piece of equipment in Plant 3 Kiln MCC. When he was tightening the motor leads he felt a sharp pain in the left side of his back. EE was taken to the local physician and was ordered physical therapy for strained back muscle.

Employee was cleaning stuck feed from the Plant 2-3 roller mill chute with a crowbar. Employee hit the side of the chute causing him to hit his hand with the crowbar.

EE CUT FOREARM WITH RAZOR OPENING A BOX OF PAPERBAGS.

EE WAS CUTITNG A PIECE OF GUM RUBBER WITH UTILITY KNIFE, WHEN EE CAME TOT HE END OF THE RUBBER THE KNIFE SLIPPED AND CUT HIM ON THE LOWER RIGHT THIGH AREA. THE LACERATION REQUIRED 3 STITCHES.

EE WAS CLEARING A HOPPER WITH A 2" BAR WHEN THE BAR SLIPPED AND MASHED HIS LEFT PINKY FINGER BETWEEN THE BAR AND THE HOPPER. RESULTED IN 2 STITCHES.

EMPLOYEE WAS ATTEMPTING TO OPEN AN ACTUATOR VALVE WHEN HSI WRENCH SLIPPED CAUSING HIS RIGHT HAND TO GET PINCHED BETWEEN THE VALVE AND A STANDING PIPE. THIS RESULTING IN 4 STITCHES TO THE PALM ON RIGHT HAND.

EE WAS SUPERVISING THE OPERATION OF CLEANING MATERIAL FROM A PUG MACHINE. CO-WORKER WAS USING A SCRAPER (LONG HANDLE) TO CLEAN MATERIAL OFF THE PUG FACE WHEN THE SCRAPER GLANCED OFF THE PUG AN D HIT EE ABOVE THE RIGHT EYE CAUSING A 1 INCH LONG LACERATION REQUIRING 3 STITCHES.

EMPLOYEE WAS OPENING THE BOTTOM DOORS ON RAILCAR (WITH A BAR) WHEN HE FELT PAIN IN HIS LOWER BACK. THE PAIN FURTHER PROGERSSED IN A 10 DAY PERIOD TO WHERE THE EMPLOYEE SEEKED MEDICAL TREATMENT .

EE WAS PULLING BELT UP WITH CHAIN COM-A-LONG ANDCHOKER WRAPPED AROUND BELT UNDER A BUCKET. THE BUCKET TORE OFF THE BELT AND THE BELT SLIPPED THROUGH THE CHOKER HITTING HIM ON THE SIDE OF TH E LEG.

EMPLOYEE WAS CHANGING BEARING ON A TAILROLLR SHAFT. HE WAS PACKING THE SHAFT WITH A CROW BAR TRYING TO SLIDE THE BEARING ON WHEN THE SHAFT FELL. EMLYEE'S FINGER WAS SMASHED BETWEEN THE FLOOR AND THE CROW BAR WITH A SHAFT ON TOP.

SUBJECT WAS TRIMMING ENDS OF PLASTIC CURTAIN STRIPS WITH UTILITY KNIFE--KNIFE SLIPPED AND CUT LEG ABOVE RIGHT KNEE--SUBJECT WAS CUTTING TOWARDS HIS BODY.

INJURED BROOKINS WAS HELPING TO UNLOAD BAUXITE RAIL ROAD CARS. INJURED WAS OPENING AND CLOSING BOTTOM CAR DOORS WITH A STEEL BAR AS HE WAS USING STEEL BAR-IT SLIPPED AND HE FELL TO THE GROUND

THREE EE WERE WORKING TOGETHER TO TOPEN THE BOTTOM DOOR OF A RAIROAD CAR SO IT COULD BE UNLOADED EE WAS USING AN IRON BAR TO OPEN THE DOOR. HE FELT A PAIN IN HIS CHEST ON THE LEFT SIDE.

EE CLEANING A CHUTE USING A CROWBAR--RIGHT RING FINGER GOT BETWEEN THE CROWBAR AND CHUTE. MASHED FINGER.

EMPLOYEE WAS CLEANING INFEED CHUTE TO KILN WITH A METAL ROD.HE STRUCK HIS FINGER ON A SHARP PIECE OF METAL WHICH WAS PART OF THE CHUTE.

CONVEYOR DRIVEN BY DC MOTOR. CONVEYOR WAS LOCKED DOWN AND EMPLOYEE USED PRY BAR TO GET THE COVNEYOR TO MOVE.

TWO EMPLOYEES WERE WORKING ON BREAKING BELLY PAN LOOSE SO THEY COULD REPLACE THE STARTER. INJURED WAS LAYING UNDER DOZER USING A 3' CHEATER PIPE ON 3/4"PULL HANDLE. HE PUT BOTH FEET AGAINST THE HOUSING SO HE COULD PUSH WITH HIS LEGS TO HELP GET THE BOLTS LOOSE.

3 MEN MOVING SHUTTLE CONVEYOR. INJURED WAS USING A PRY BAR AND BAR SLIPPED AND HE FELL.

STRAIN TO BACK USING A PRY BAR UNDER AXLE OF SHUTTLE CONVEYOR. PRY BAR PLACED UNDER AXLE OF CONVEYOR AND EE WAS LIFTING UP ON PRY BAR.

ENTERED PELLET BIN TO BREAK UP BUILD UP SO IT WOULD COME OUT OF THE BIN. MATERIAL BUILD UP WAS 8 FT ABOVE THE CONVEYOR BELT AT THE SOUTH SIDE OF THE BIN. HE AND HELPER WERE DIGGING MATERIAL LO OSE. HE MOVED TO NORTH END OF BIN. A LUMP OF BUILD UP FELL AND STRUCK LEFT KNEE.

REBUILDING ROLLER MILL. BEARING ADAPTOR WAS IN PLACE ON SHAFT AND HE WAS PUTTING THE NUT ON THE END OF THE SHAFT. THE BEARING ADAPTOR SLIPPED DOWN AND STRUCK HIS FINGE.R RIGHT HAND MIDDLE F INGER, BONE CRACKED.

HE HAD REPLACED A SCREEN ON THE SWECO SYSTEM. PUTTING SYSTEM BACK TOGETHER, HE TIGHTENING SEALING BANK ON SYSTEM WITH A RATCHET WRENCH, HE PULLED HARD TO TIGHTEN BAND AND HE FELT SOMETHING I N HIS BACK.

EE WAS TRIMING THE END OF SOME ELECTRICAL WIRE WITH HIS KNIFE. THE WIRE TWISTED IN HIS HAND AS HE WAS TRIMING IT CAUSING HIM TO CUT HIS LEFT INDEX FINGER WITH HIS KNIFE.

CLEANING OF DISCHARGE OF COOLER WITH A SHOVEL. MATERIAL FELL INTO HIS LEFT EAR.

REBUILDING FEEDER, GEAR HAD BURR ON IT, GEAR TO BE REUSED, EMPLOYEE USED A HAMMER AND CHISEL HAND SLIPPED AND WAS CUT ON BURR. CUT BASE OF LEFT THUMB PLUS A PIECE OF METAL WAS IN CUT.

CHANGING OUT OLD CABLE ON PETTIBONE CRANE-EMPLOYEE SWINGING SLEDGE HAMMER TO BREAK SHEAVE BLOCK LOOSE-SWINGING OVERHEAD CAUSING AN UNBALANCE WITH AHMMER.SHARP PAIN IN LOWER PART OF STOMACH.

EMPL CHAGING TROUGHING ROLLER #5 COAL INCLINE CONVEYOR REMOVING BOLTS THAT HAD PAIN ON IT PAIN FLAKED OFF INTO R EYE EMPL LOOKING UP OVER HEAD EMPL WAS WEARING GLASSES

REMOVING PUG FO2T FROM MAIN SHAFT ON PUG MACHINE MISSED FOOT WITH SLEDGE HAMMER.HIT FINGER BETWEEN TUB WALL AND HAMMER HANDLE CUT ON RIGHT INDEX FINGER.

DRIVING HOPPER 7EETH OFF OF SHAFT WITH HAMMER. MISSED TOOTH WITH HAMMER AND HIT THE TOOTH WITH KNUCKLE ON LITTLE FINGER OF RIGHT HAND.

EMPL USING ADJU8TABLE WRENCH.WHILE PULLING ON IT WITH PRESSURE,IT SLIPPED.WITH REFLEX MOVEMENT WITH LEFT HAND TO SUPPORT HIMSELF HE BUMPED HIS LEFT WRIST.

EMPLOYEE WAS IN3AN AWKWARD POSITION USING A SLEDGE HAMMER TO CLEAN FEED CHUTS-SLEDGE HAMMER BOUNCED BACK & STRUCK HIM IN THE MOUTH

EMPLOYEE CLAIMS3HOPPER GATE WAS STRUCK IN CLOSED POSTIONFHE GOT A CROW BAR AND TRIED TO FREE THE GAT.BAR SLIPPED AND MASHED HIS FINGER BETWEEN BAR AND IRON FRAME.