Buscar en el registro

EE was using a line truck to disconnect power line after storm. After cutting 2nd wire, pole broke striking ee across back, shoulders and head, knocking off hard hat. He received laceration to scalp and multiple insect bites.

Employee exerted force on a pry bar to install a 20" 90 degree fitting. injury was aggravated when he used a shovel as a normal part of his job, resulting in sprain of ligaments in elbow.

ELECTRICAL SUPERVISOR AND ELECTRICIAN WERE CUTTING A WIRE TIE OFF A SET OF BUNDLED WIRES WHEN KNIFE SLIPPED OFF THE WIRE TIE AND CUT ELECTRICIAN'S HAND.

EMPLOYEE WAS USING A POCKET KNIFE THAT DID NOT HAVE A LOCKING BLADE TO TRIM ON A URETHANE WEDGE GASKET USED IN SEALING 20"PIPE FLANGES. BLADE CLOSED ON FINGER, CAUSING THE CUT (REQUIRING SUTURES).

EE WAS ATTEMPTING TO CLOSE LOWER DOOR OF RAIL CAR WITH PRY BAR. THE PRY BAR SLIPPED & HIT EE IN FACE CAUSING A LACERATION TO RT. UPPER LIP. 2 SUTURES WERE REQUIRED TO CLOSE THE WOUND.

EE WAS USING A SLEDGE HAMMER TO DRIVE A PIN THROUGH TWO BORES WHEN THE HAMMER HANDLE BROKE ALLOWING THE 20 LB SECTION OF THE HAMMER TO FLY OFF AND LAND ON HIS HAND.

ANOTHER EE WAS USING SLEDGE HAMMER TO PUT IN A BACK HOE PIN. HAMMER GLANCED OFF PIN KNOCKER, HIT EE IN MOUTH.

EMPLOYEE WAS ATTEMPTING TO SHORTEN A PLASTIC DRAIN LINE WITH A POCKET KNIFE. SHE WAS HOLDING THE TUBING IN A "U" POSITION AND ATTEMPTED TO PUSH THE KNIFE AWAY FROM HER TO COMPLETE A CUT. HER L EFT INDEX FINGER WAS STABLIZING TUBE AND KNIFE CUT THROUGH TUBING INTO TOP OF FINGER. LACERATION REQUIRING THREE SUTURES.

EE WAS APPLYING FORCE TO A COMEALONG HOLDING A PIPE THAT HAD MOVED AFTER THE BOLTS WHERE REMOVED FROM A FLANGE. THIS PIPE HAD MOVED MORE & IN A DIFFERENT DIRECTION THAN PLANNED. EE PERFORMED T ASK WITH LESS THAN DESIRABLE THOUGHT FOR BODY POSITION & EXERTION, RESULTING IN MUSCLE STRAIN. EE WAS PLACED ON RESTRICTED DUTY ON 6/4 & X-RAYS WERE ORDERED.

WHILE BOLTING A 20" FLANGE PIPE TOGETHER DURING WINDY WARM CONDITIONS, EMPLOYEE WAS OFTEN CLEANING SWEAT AND SAND FROM HIS FOREHEAD BY WIPING IT WITH WORK GLOVES RATHER THAN A CLEAN RAG. A SMA LL SLIVER OF STEEL WAS REMOVED FROM HIS RIGHT EYE.

30" BAR SLIPPED WHILE EE WAS HOLDING BELLY PAN IN PLACE SO BOLTS COULD STARTED.

AFTER WELDING NEW BRACKETS, EMPLOYEE RAISED WELDING HOOD AND BEGAN TO CHIP WITH HAMMER. A PIECE OF HOT SLAG FLEW INTO LEFT EYE.

MECHANIC WAS PULLING LOG SHAFT UP HILL WITH 3/4 TON COMEALONG. THE HOOK ATTACKED TO COME-A-LONG HOUSING BROKE CAUSING MECHANIC TO FALL BACKWARDSONTO LOG SHAFT CAUSING CONTUSION TO LOWER BACK A ND GLUTEAL AREA.

EMPLOYEE WAS REMOVING BOLTS FROM A FLANGE ON THEHYDRAULIC LINE WHEN HE FELT A PAIN IN LOWER BACK

INJURED EE WAS ASSISTING ANOTHER EE TO PUSH A FLANGE TO A BACK UP RING ON 22' PIPE BY USING A TAPPING METHOD WITH A 10 LB SLEDGE HAMMER. THE NON-INJURED EE HAD HIS BACK TO THE FLANGE AND WOULD NOT SEE THE PLACEMENT OF INJURED EE'S HAND.

EMPLOYEE WAS ADJUSTING BELT SKIRTING ON TRANSFERPOINT ON STACKER CONVEYOR. HE WAS USING A PRY BAR TO LIFT THE RACKETS THAT HOLD THE SKIRTING WHEN THE BAR SLIPPED, STRIKING EMPLOYEE IN THE CHIN . THE INJURY REQUIRED THREE SUTURES FOR CLOSURE.

EE'S CREW WAS CHANGING OUT DRAGLINE BUCKET. EE WAS USING A 5' RR BAR TO KNOCK HITCH PLATE PIN FROM HITCH PLATE. WHEN PIN CLEARED, BAR WENT INTO HITCH PLATE. LEFT HAND WAS PINNED BETWEEN TRONNI ON CLEVIS AND BAR CAUSING A CRUSHING INJURY TO LEFT LITTLE FINGER.

EE WAS USING A PRYBAR TO TURN ANTIROTATION RATCHET ON TOP OF MOTOR TO FACILITATE REMOVAL OF RATCHET ASSEMBLY WHEN THE PRY BAR SLIPPED OFF ASSEMBLY AND STRUCK EE IN THE FACE BETWEEN THE LIP AND CHIN. THREE SUTURES WERE REQUIRED TO CLOSE THE WOUND.

TRYING TO DRIVE PIN OUT OF A HYD CYLINDER WITH A B&O AND SLEDGE HAMMER AND A PIECE OF METAL CAME OFF AND WENT INTO HIS ARM, EMBEDDING IN ARM

SHARPENING MACHETE WITH FILE, HAND SLIPPED, CUT THUMB ON LEFT HAND

IMPROPERLY USED EQUIPMENT AND INADEQUATE TOOLS.

DEFECTIVE EQUIPMENT. EE FAILED TO CHECK EQUIPMENT PRIOR TO USE.

A PIECE OF RUBBER CAME LOOSE INSIDE AN 8" LATERAL AND WAS BLOCKING THE FLOW TO ONE OF THE CP SCREENS. EE WAS CUTTING RUBBER OUT WHEN KNIFE SLIPPED AND CUT TWO FINGERS ON LEFT HAND. BOTH LACERA TIONS REQUIRED A TOTAL OF SIX SUTURES FOR CLOSURE.

A WORKER WAS WORKING AT PULLING THE TAIL BEARING OFF A CLASSIFIER WHEN HE STRAINED A MUSCLE OR PULLED SOMETHING INTERNALLY. HE DID NOT MENTION THIS TO THE OTHER WORKERS OR SUPERVISOR. HE WORKE D THREE DAYS AFTER THIS THEN WHEN TO SEE A DOCTOR ON MONDAY 4 DAYS LATER.

EMPLOYEE WAS WORKING FROM A LADDER, DOING PIPE WORK USING A LARGE WRENCH AND AS HE ATTEMPTED TO BREAK THE BOLT HE FELT A STINGING SENSATION IN HIS LEFT GROIN AREA.

EE WAS REMOVING BOLTS FROM BEARING COVER ON FALK REDUCER TO CHECK GEAR RATIO. IN THE PROCESS OF INSPECTION, SHAFT ASSEMBLY FREED UP FROM GEAR BOX, CAUSING REDUCER BASE TO DROP ON LEFT FOOT.

EMP WAS WORKING ON 18" X 44" PUMP TO REMOVE THE FACE PLATE. WHILE USING A BAR TO REMOVE PLATE FROM PUMP, THE BAR SLIPPED AND EMP LOST HIS BALANCE CAUSING HIM TO TWIST HIS KNEE.

HELPING INSTALL STEEL CHUTE USING COMEALONG. COMEALONG MALFUNCTIONED CAUSING CHUTE TO DROP ONE FOOT. STRUCK EE AND KNOCKED HIM DOWN ON BEAM, BEFORE ANYONE COULD REACH HIM HE ROLLED OFF AND FEL L TEN FEET TO THE GROUND.

HELPING INSTALL STEEL CHUTE USING COMEALONG. COMEALONG MALFUNCTIONED CAUSING CHUTE TO DROP ONE FOOT. EE WAS INSIDE CHUTE AND LANDED ON FEET, THEN FELL TO THE GROUND LANDING ON RT SIDE.

EMPLOYEE WAS PRYING ON A SHAFT WITH A 5 FT. BAR USING SIDE PRESSURE. AT ONE POINT HE LEANED ALL HIS WEIGHT ON THE BAR AND THE BAR SLIPPED CAUSING HIM TO LOSE HIS BALANCE AND FALL AGAINST A DRA G DRUM SPIDER RIM WITH HIS LOWER RIB CAGE. THIS FRACTURED 2 RIBS, #8 AND #9. HE REPORTED THIS TO ME AT 12:30 PM. I TOOK HIM FOR X-RAYS. THE DR. SAID RETURN TO WORK THE NEXT DAY & HE DID.

EE PULLING ON A RAKE TO CLEAR DEBRIS IN HAMMERMILL CHUTE.

INJURED WAS ATTEMPTING TO TIGHTEN HYDRAULIC PUMP PACKING GLAND WITH A SOCKET WRENCH THE WRENCH SLIPPED OFF THE NUT AND MASHED HIS FINGER AGAINST THE PUMP HOUSING.

TRYING TO REMOVE PUMP PACKING TOOL RELEASED UNEXPECTEDLY CAUSING INJURED TO LOOSE BALANCE, STRAINING HER UPPER BACK.

EE WAS REPLACING A HANDRAIL AT THE BENEFICIATIONPLANT, IN ORDER TO LINE UP THE ANGLE IRON HE REACHED AROUND A BEAM WITH A VALVE CHEATER, PULLINGAGAINST HIS CHEST. IMPROPER POSITION & NOT USING THE PROPER TOOL.

GROIN PULL WHILE PULLING WRENCH/TIGHTENING BASE BOLTS ON 1250 HP ELECT. MOTOR.

LACERATION RIGHT THUMB/HIT BY HAMMER WHILE PEENING STEEL PIN.

EMPLOYEE WAS USING A KNIFE TO CUT A GASKET KNIFE SLIPPED STRIKING THE LITTLE FINGER ON HIS LEFT HAND

EE WAS USING 3/4 NYLON ROPE TO RELOCATE A FLATING DEWATERING PUMP. ONE END OF THE ROPE CAME LOOSE UNDER EXTREMEM PRESSURE AND STRUCK THE EE IN THE RIGHT JAW.

EMPLOYEE WAS HOLDING A 3/8" DRILL IN HIS HAND WHILE ATTACHING A 3/4" HOLE SAW. THE SCREWDRIVER SLIPPED OFF THE SET SCREW AND STRUCK HIS PALM.

EMPLOYEE WAS USING POCKETKNIFE TO TRIM SOME PLASTIC FROM THE EDGES OF A SHAKER SCREEN PANEL SO IT WOULD FIT INTO ITS SLOT.THE KNIFE SLIPPED STRIKING THE EMPLOYEE IN THE WEB OF HIS LEFT HAND.

EMPLOYEE WAS USING A 20LB SLEDGE HAMMER TO STRIKE A B&O TOOL IN AN EFFORT TO REMOVE A TOOTH FROM A 1260W BUCYRUS-ERIE DRAGLINE BUCKET A FRAGMENT OF METAL BROKE OFF THE TOOTH & IMBEDDED IN H IS RT UPPER THIGH

EMPLOYEE WAS USING A 20LB SLEDGE HAMMER TO DRIVEA NEW 2 7/8IN DRAG CABLE & WEDGE INTO THE SOCKET ONE BLOW OF THE HAMMER SLIPPED MASHING HIS LEFT INDEX FINGER BETWEEN THE CABLE & HAMMER HANDLE

EMPLOYEE WAS USING A WELDERS CHIPPING HAMMER IN AN ATTEMPT TO REMOVE A METAL BAND HOLDING A PIPE NIPPLE INSIDE A 1IN WATER HOSE A FRAGMENT OF METAL BROKE OFF THE TIP OF THE HAMMER & IMBEDDED I N HIS LEFT HAND

EMP WAS USING A36' STEEL PRY BAR TO CLOSE BOTTOM RAILROAD HOPPER CARS. THE PRY BAR SLIPPED CAUSING HIM TO FALL BACKWARDS ONTO HIS RIGHT FOOT

EMPLOYEE WAS WO9KING ON #8A PUMP DISCHARGE HE WAS LIFTING A PIPE WITH A PORTABLE CABLE HOIST THE CABLE SLIPPED CAUSING THE END OF THE DISCHARGE PIPE TO STRIKE THE EMPLOYEES ARM

EMPLOYEE WAS PU7TING A COUPLING ON A PIECE OF ELECTRICAL CONDUIT THAT WAS BEING HELD IN A VISE THE VISE SLIPPED AS I TURNED THE COUPLING WITH A VISE CAUSING MY HAND TO HIT THE BENCH VISE