Buscar en el registro

On 8/29/2008, the employee was swinging a 10 pound sledge hammer against the side of a rail car to unload stuck limerock roadbase and suffered a strain in his R shoulder. The shoulder was sore for a couple of weeks and did not improve. On 9/15/2008 the employee was taken to the doctor for evaluation and diagnosed with a shoulder sprain and placed on light duty.

On 1/7/2008 Employee was unloading rail cars. As he was closing the rail car hopper door with a spud bar, he lost his footing and twisted his knee. He was taken to the doctor to be examined the following day, placed on restricted duty and given a prescription for pain.

Employee had complained about a lump in the palm of his right hand on 9/28 at 2:00. There was no problem at the time and he requested to see Dr. Joy who had seen him before. The doctor's next available date was October 6th. On Oct. 6 the doctor placed him on prescription drugs and refered him to a specialist. This is now a reportable accident as of October 6.

Employee cut his hand with a sharp knife. He was attempting to score and break a plastic tray. The knife slipped and cut his hand. Sutures were required.

employee was cutting a piece of conveyor belt skirting when the knife slipped and plunged into his leg.

Ee complained of sore arm about a week after the event (4/10/06). On 4/12 he went to see his own physician who told him that he had a strain and that it was work related. On 4/13 he was sent to our dr. who diagnosed a strain. PT and light duty prescribed.

WORKING ON SCRUBBER PUTTING BELTING ON THE INSIDE. HE WAS USING A SHOVEL TO PUSH DOWN ON IT AND IT SLIPPED AND CAUGHT HIS LITTLE FINGER BETWEEN SHOVEL AND SIDE OF BELT.

Ee developed callous on right hand from using hand tools. Callous is impinging on movement of right little finger.

EE WAS OPENING A DOOR ON AN EXPANSION CHAMBER (1ST STAGE- 7TH HOUR). USING A PRY BAR, HE WAS PULLING AGAINST A STUCK HINGE. THE BAR SLIPPED, HE STEPPED BACKWARD & TWISTED HIS FOOT, FRACTURING A BONE IN HIS LEG.

EE WAS LOOSENING THE NUT ON A DRAW CYLINDER FOR THE GRAVEL BED FILTER SYSTEM. HE WAS TURNING A NUT WITH A WRENCH. THE NUT CAME TO THE END OF THE THREAD AND THE SHAFT FELL PULLING THE WRENCH DO WN, CRUSHING HIS FINGER.

WHILE EE WAS CUTTING A CONVEYOR BELT THE RAZOR KNIFE HE WAS USING SLIPPED OFF BELT, CUTTING HIS LEFT MIDDLE FINGER.

EE CUT THE BACK OF HIS HAND WITH A PUTTY KNIFE WHILE CLEANING THE WAX OFF OF A CEMENT MOLD IN THE LAB AREA.

CLEANING OUT GRIZZLY. HE HIT HIS SMALL FINGER ON ONE OF THE RAILS WHILE USING A BAR TO CLEAN BUT BUILT UP MATERIALS.

EE STRAINED HIS BACK WHILE USING A HEAVY HAMMER OVERHEAD IN THE FINISH MILL.

WHILE CLEANING CONE CRUISHER @ BASE PALNT WITH IRON BAR THE CONE CRUSHER CUASED THE BAR TO COME UP AND HIT HIM UNDER THE CHIN.

EE CUT THUMB W/ KNIFE WHILE CUTTING RUBBER BELT SHEET.

CUTTING THE VACTOR HOSE WITH A SHARP KNIFE.

EE WAS USING A KNIFE TO SCRAPE MATERIAL OFF OF ABOLT. THE KNIFE FOLDED UP ON HIS FINGER CAUSING LACERATION.

ON 12/21/00 INJURED WAS ON PROPERTY TO REMOVE A B.E. MODEL 38B RUBBER TIRED TRUCK CRANE/CLAM SHELL MACHINE. THEY REMOVED THE BOOM & SHIPPED IT OUT. THEY THEN BEGAN TO REMOVE COUNTER-WEIGHT. TH ERE WERE 2 STUDS SECURING WEIGHT THAT WERE RUSTED. THEY SPLIT NUTS W/TORCH & USED PIN & HAMMER TO BREAK OFF. THE WEIGHT FELL 6' ONTO INJURED LANDING ON THIGHT/LEG. 911 CALLED, EE CONCIOUS/TAL

EE WAS WORKING AT BARE PLANT WHEN A ROCK GOT SDTUCK. HAD TO BREAK IT WITH A SLEDGE HAMMER AND BAR AND STRAINED HIS SHOULDER. EE DID NOT VIOLATE ANY SAFETY RULES DURING THIS INCIDENT.

EE WAS USING REMOVEABLE CHUTE HANDLE. THE HANDLE CAME OFF AND STRUCK THE EMPLOYEE IN THE CHIN.

COMEALONG BROKE WHILE PULLING A TAIL PULLEY BACKINTO PLACE. CHAIN OFF THE COMEALONG BROKE RECOILING TOWARD LEFT EYE AREA

WHILE ADJUSTING CRUSHER, EE WAS REMOVING THE ADJUSTING WEDGE FROM THE LOCKPART WITH 2 LB HAMMER. EE WAS SWINGING HAMMER WITH RIGHT HAND WHILE THE OTHER END OF THE WEDGE WITH HIS LEFT HAND. AFT ER KNOCKING THE WEDGE LOOSE THE IMPACT CARRIED THE WEDGE AND HIS LEFT HAND INTO THE ADJUSTMENT POST, LACERATING 5TH DIGIT ON LEFT HAND KNUCKLE AREA.

COMEALONG CAME LOOSE WHILE MOVING CHUTE CAUSING BACKLASH FORCING LEFT HAND INTO STEEL BEAM

EMPLOYEE WAS PULLING ON VALVE, AND HAD TO USE A HAMMER TO REMOVE IT. EMPLOYEE FELT A PULL IN HISSHOULDER.

EE WAS POKING WET GYPSUM IN A HOPPER OVER THE GYP FEEDER.

EE WAS TRYING TO DISLODGE PIECE OF STEEL FROM JAW CRUSHER. BLOCK OF STEEL CAME OUT & SMASHED END OF RIGHT THUMB

EE STATED THAT HE WAS REMOVING A 100 LBS SPROUCKET IN WHICH A COME A LONG WAS ATTACHED WHEN HE MOVED THE SWITCH AN THE COME ALONG TO THE LOWER POSITIONS IF FREE WHEELED AND THE SPROCKET HIT HI S BIG TOE NO RIGHT FOOT. SUFFERED A LACERATION ON THE RIGHT BIG TOE AND TWO FRACTURES.

2 EES WERE DOING A CONVEYOR BELT SPLICE ON CONVEYOR #27. THE 2 MATING SURFACES HAD BEEN CUT, BUT ONE SIDE NEEDED TO BE TRIMMED. INJURED EE WAS HOLDING BELT IN POSITION, WITH HIS LEFT THUMB IN THE PATH OF THE KNIFE BLADE. AS FELLOW EE TRIMMED, THE BLADE CAME THROUGH TRIMMED AREA & CUT EE'S THUMB. IT REQUIRED 6 SUTURES TO CLOSE.

EE WAS BANGING ON A HOPPER UNDER THE CRUSHER WITH A SLEDGE HAMMER, FELT PAIN IN GROIN. DIAGNOSEDWITH INGINAL HERNIA ON 1/8/98 FIRST DATE OF TREATMENT. EE UNDERWENT SURGERY ON 2/19/98

EMPLOYEE WAS WORKING ON JAW CRUSHER IN THE PLANT. HE WAS USING A SLUG WRENCH TO TIGHTEN THE LINERS. HE HIT HIS THUMB WITH A HAMMER.

EMP WAS SHOVELING IN 806 RECLAIM TUNNEL. DUST ENTERED HIS EYES. EYES BECAME IRRITATED. IRRIGATEDEYES THEN IGNORED SYMPTOMS FOR FEW HOURS. SUPERVISOR SENT HIM TO DR 6 HOURS LATER.

EE WAS CLEANING OVERHED VENT IN CEILING PANELS IN CONTROL ROOM BUILDING. LOOSE MATERIAL FROM VENTS FELL INTO BOTH EYES.

HAMMERING ON METAL TABLE WITH RAILS. EE WAS HITTING RUST OFF BOLTS HEAD, WHEN HIS KNUCLE HIT SHARP EDGE OF TABLE.

EMP WAS USING A PRY BAR TO LOOSEN THE BELLY PAN ON A D-6 DOZER. PAN FELL OFF AND EMP LOST HIS GRIP ON PRY BAR. BAR FELL AND STRUCK EMP ON TOP OFTHE RIGHT WRIST.

EMPLOYEE WAS CLOSING DOOR ON COAL GONDOLA. WHILE SWINGING THE SLEDGE HAMMER HE FELT A "TINGLE" IN HIS BACK. EMPLOYEE UNABLE TO RETURN TO WORK ON THE NEXT SCHEDULED SHIFT(SAT. NOV. 30)

EE WAS INSTALLING TEETH ON THE DRAGLINE BUCKET, BENDING THE KEEPER PINS. WHILE HOLDING A HAMMER PUNCH ANOTHER EE WAS USING A 8 SLEDGE HAMMER. THE SLEDGE HAMMER HADLE HIT EE S LEFT THUMB. ACCID NET RESULTED IN THE LEFT THUMB WITH A CHIPPED BONE, AND DR PUT THE THUMB IN A SPLINT.

EE WAS FILLING TOP OF BINS CONVEYOR BELT STUCK. EE CLIMBED UP WALKWAY AND TRIED TO MOVE IT OVER WITH A PRY BAR. THE PRY BAR SLIPPED HITTING THE EE IN THE FACE.

EE WAS TRYING TO DISLODGE A ROCK USING A PRY BAR. THE ROCK CAME LOOSE AND HIT HIM IN HEAD.

EE WAS PULLING BACK ON A STEEL PLATE USING THE CHAIN HOIST AND CAUGHT HIS FINGER IN THE CHAIN.

EMPLOYEE WAS TRYING TO DISLODGE ROCK FROM FEEDER USING A PRY BAR AND FELT PAIN IN HIS LOWER BACK.

EMPLOYEE STRUCK BACK OF HIS LEFT HAND ON A PIPE WHILE USING SLEDGE HAMMER.

WHILE TURNING WRENCH, HE STRAINED HIS LOWER BACK.

EE WAS PULLING ON A WRENCH AND FELT SORE AT END OF SHIFT--ATTRIBUTED TO PULLING ON WRENCH. THIS IS A REPORTABLE INJURY--THERAPY PRESCRIBED.

KNOCKING OUT BOLT WITH HAMMER & DRIFT MAKING A LOT OF DUST DUST GENERATED IN THE PROCESS ENTERED HIS EYE EMPLOYEE RUBBED EYE CAUSING ABRASION EMPLOYEE USED PERSCRIPTION DRUGS

EMPLOYEE WAS REMOVING A PIN FROM A LIFT CYLINDER LOACTED BENEATH THE CEMENT SILOS. WHILE PUSHING THE PIN OUT OF THE BRACKET, THE SCREWDRIVER SLIPPED & STABBED HIS FINGERS.

EMPLOYEE COMPLAINED AFTER SWEEPING & SHOVELING THAT HIS SHOULDER HURT. EMPLOYEE HAD UNDER GONE SURGERY IN OCTOBER 1993 TO REPAIR ROTOR CUFF IN JURY. EMPLOYE RELEASED TO RETURN TO WORK ON 4-18 -94. EMPLOYEE STATES THAT HE NEVER WAS WELL AND THE PAIN PERSISTS-NO INCIDENT OCCURED.

EMPLOYEE WAS USING RAZOR KNIFE TO ENLARGE HOLE ALREADY PUNCHED IN RUBBER LINING. HE WAS SITTING DOWN, HOLDING THE RUBBER WITH HIS LEFT HAND AND USING THE RAZOR KNIFE WITH HIS RIGHT HAND. THE KNIFE SLIPPED, LACERATING HIS LEFT HAND.

EMPLOYEE WAS INSTALLING A VIBRATOR ON A RAIL CAR. HE WAS PUSHING DOWN ON THE WRENCH BY PLACING ALL HIS WEIGHT ON THE RATCHET WRENCH. THE EMPLOYEE'S WEIGHT CAUSED THE LOCK ON THE WRENCH TO SLIP . THE EMPLOYEE FELL FORWARD AND HIT HIS CHIN ON THE VIBRATOR.

HAMMERING SCREEN BOLT INTO DIVISION HEAD. ON FORWARD SWING, 16-LB. SLEDGE HAMMER INTERFERED WITH LADDER CAUISN GOFF BALANCE, WHICH CAUSED HAMMER HEAD TO MISS BOLT ALLOWING RIGHT FINGER TO CO NTACT BETWEEN HAMMER HANDLE AND BOLT HEAD.