Buscar en el registro

Employee was attempting to dislodge a stone in a jaw crusher with a long steel rod. As EE used downward pressure to strike the stone, EE struck EE's right hand on the edge of a steel plate that surrounded the crusher.

Employee was doing maintenance on a conveyor belt. Employee was cutting rubber for a skirtboard with a utility knife. Employee cut themselves in the left hand through a leather glove. Employee required sutures to close the wound.

Middle finger hit with sledgehammer causing finger fracture & lacerations.

Two EEs were using tanker bars to adjust a radiator on a pallet to prepare it for shipping. As the two were both pushing on the bars, the injured EE lost control of bar and slipped off the radiator causing EE to fall to the ground. When EE fell, right knee impacted the concrete floor of the shop. EE immediately felt a pain in lower back, side, a leg.

Miner was attempting to remove a rock that was in the collection box at the top of conveyor #3 at the primary before plant start-up. Employee was prying a rock with a bar that was about 6" that was wedged against other material. While the miner was pulling the bar, the rock became free and the bar pinched EE's pinky finger on the left hand between the top of the box and the bar.

Employee slipped and struck knee with a wrench causing a small cut. Injury became reportable on 9/14/2016 when employee went for medical treatment and was give restrictions and prescription medication for infection.

Employee was using chipping hammer while doing maintenance on stone plant Deister screen. Employee's hands were sweaty and slipped down shaft of chipping hammer, hitting screen and causing small laceration, bruise and swelling. On 7/7/2016 employee sought medical attention for the swelling that had not receded. Diagnosis was broken bone in left hand.

Employee was pulling on a wrench when he felt pain in his shoulder. Employee went to the Chiropractor on 10/28/14, this is the date the injury became reportable.

EMPLOYEE USING UTILITY KNIFE TO CUT CONVEYOR BELT. KNIFE SLIPPED, CUTTING THROUGH SAFETY GLOVE, LACERATING LEFT INDEX FINGER.

EMPLOYEE CUTTING AND SPLICING CONVEYOR BELT AT CRUSHING PLANT, USING UTILITY KNIFE AND T-SQUARE - CUT RIGHT HAND WITH UTILITY KNIFE REQUIRING STITCHES AT LOCAL EMERGENCY ROOM.

Employee hit finger with a hammer while changing screen.

While loosening bolts to remove screen, felt a pop in his groin area.

Pry bar slipping, impact on left elbow causing surgery for torn bicep tendon.

EE was changing worn screen panel. Because of rain and very tight quarters inside the screen, EE slipped with a razor knife, cutting through his gloves into this finger.s

Employee was prying material out of bin when pry bar slipped and crushed 4th finger on left hand.

Struck with metal chip while removing a bearing race.

EE was cutting rubber belting when the knife (box cutter) slipped cutting his left index finger on the side.

WHILE REMOVING FITTING FROM SUMP PUMP, THE EMPLOYEE CRUSHED THE MIDDLE FINGER ON HIS LEFT HAND WHEN THE PIPE WRENCH SLIPPED FROM THE VISE AND HIT HIS FINGER.

Cut left thumb with utility knife.

EMPLOYEE HOLDING HAMMER WRENCH AND HIT WITH SLEDGE BY OTHER EMPLOYEE.

CLEANING HOPPER UNDER 5 SCREEN WITH SCRAPER. HIT HAND BETWEEN HANDLE OF SCRAPER AND ANGLE IRON BRACKET.

EE WAS SEATED USING LARGE WRENCH TO PERFORM MAINTENANCE ON CRUSHER. WHEN EE STOOD UP HE FELT PAIN IN LOWER BACK & LEG. HE WAS ASSISTED OFF CRUSHER AND AWAITED MEDICAL ATTENTION.

EE WAS USING PICKAXE TO CLEAN FROZEN CHUNKS OF STONE OFF GRATES ON STONE HOPPER. EE STRAINED BACK MUSCLES WHILE DOING SO.

EE WAS CRANKING THE HANDLE OF THE LANDING GEAR ON A TRAILER. HE LET GO OF THE HANDLE, THE HANDLE THEN REVERSED DIRECTION, SPUN AROUND AND STRUCK HIM IN THE FACE (MOUTH CHIN AREA)

EE WAS SHOVELING STONE AND WHEN HE DREW BACK THE SHOVEL IN HIS HAND, HIS RIGHT HAND BRUSHED AGAINST THE GUARD CAUSING A LACERATION.

INJURED EMPLOYEE WAS HOLDING A ROD TO BE STRUCK BY A HAMMER BY A FELLOW EMPLOYEE. THE ROD WAS PARTIALLY STRUCK RESULTING IN A STRIKE TO FINGERCAUSING A FRACTURE.

THE EE WAS REPAIRING A SCREEN PANEL. WHILE TIGHTENING A NUT ON THE SCREEN PANEL, EE LOOKED DOWN TO CHECK HIS FOOTING AND THE SOCKET SLIPPED OFF THE NUT AND HIS HAND HIT THE ANGLE IRON.

MECHANIC WAS REMOVING BOLT FROM QUARRY TRUCK TIRE RIM WHEN SOCKET BROKE AND THE BACK OF HIS RIGHT HAND STRUCK THE RIM AND WAS CUT REQUIRING THREE STITCHES.

EE WAS USING A UTILITY KNIFE TO OPEN A PACKAGE OF WIRE WHEN THE KNIFE SLIPPED CAUSING A LACERATION TO THE LEFT PALM

EE WAS SWINGING ON 8# HAMMER DXRIVING A GROUND STAKE INTO THE PARKING LOT. HE WAS DISTRACTED, MISSED THE STAKE WITH THE HAMMER, CATCHING HIS RIGH INDEX FINGER ON THE STAKE.

EE WAS CUTTING WIRE TIES HOLDING UP A PIECE OF ANVAS WITH A UTILITY KNIFE, KNIFE SLIPPED CUTTING LEFT RING FINGER.

SMASHED FINGER BETWEEN HAMMER HANDLE AND GRIZZLEY BAR.

WHILE TRYING TO UNPLUG A BIN BY PUSHING A BAR UP THE CHUTE, A STONE BROKE LOOSE AND FELL OFF BELT LINE HITTING EE'S LEFT FOOT.

WHILE TESTING ENGINE ON GENERATOR PLANT, WRENCH SLIPPED AND PULLED MUSCLES IN EMPLOYEES SHOULDERXRAYS AND PRESCRIPTIONS FOR PAIN ISSUED.

UTILITY KNIFE BEING USED TO CUT BELTING SLIPPED AND LACERATED LOWER LEFT ARM.

WHILE WORKING ON WET SCREEN, PIPE WRENCH SLIPPED & PINCHED FINGER.

WRENCH SLIPPED OFF BOLT AND RIGHT RING FINGER WAS CAUGHT BETWEEN THE WRENCH AND SIDE OF THE SCREEN BREAKING THE FINGERTIP.

EMPLOYEE WAS TAKING THE BELLY PAN OFF A LOADER WHEN THE BOLT HE WAS UNSCREWING BROKE/THAT WEIGHT BROKE THE OTHER BOLT & THE PAN CAME DOWN ON THE TOP OF HIS LEFT HAND RING FINGER HE BROKE THE T OP OF THE FINGER REQUIRED STICHES

WHILE WORKING ON FOUR-FOOT GYRODISC CRUSHER EMPLOYEE PINCHED THUMB BETWEEN HYDRALIC CYCLINDER AND PUSH BLOCK.

THE EMPLOYEE STRUCK HIS RIGHT KNEE WITH A HAMMER RESULTING IN AN EXCESSIVE BUILD UP OF FLUID AROUND KNEE CAP.

TIGHTENING UP A LIFT CYLINDER ON AN M35 STOCK TRUCK, WHEN WRENCH SLIPPED AND EE FELL ONTO THE TRUCK FRAME CAUSING EE TO CUT LAST FINGER ON LEFT HAND, RESULTING IN LOSS OF SOME SKIN AND TISSUE.

WHILE HAMMERING ON PIECE OF STEEL A CHIP BROKE LOOSE AND WENT INTO EMPLOYEES RIGHT EYE.

HAMMERING WEDGES MISSED THE WEDGE WITH HAMMER HIT WEDGE WITH L MIDDLE FINGER DEEP CUT 4 STITCHES

HE WAS TAKING UP 5 1/2' CRUSHER, WHILE SWINGING 8 ALB SLEDGE HAMMER IT CAUGHT IN BACK SWING HIT A PIECE OF STEEL AND BOUNCED BACK AND HIT HIS EYE.

WHILE REMOVING LUG NUTS WITH SOCKET WRENCH WRENCH BROKE STRIKING LEFT ELBOW.

EMPLOYEE WAS CUTTING A BELTWITH A BELT KNIFE HE WAS STANDING DIRECTLY BEHIND THE CUTTING MOTION & HE WAS ALSO CUTTING TOWARD HIMSELF WHEN THE KNIFE WENT THROUGH THE BELT IT CUT THE EMPLOYEE BE LOW THE KNEE

EXCESSIVE STRAIN WHEN PULLING ON A WRENCH ALLEGEDLY CAUSED "RECURRENT INGUINAL HERNIA" RIGHT SIDE.

EMPLOYEE WAS USING A WRENCH TO TAKE OFF A LOCK NUT ON A HEAD SHAFT TO PUT MORE POWER ON THE WRENCH THE EMPLOYEE STEPPED ON THE WRENCH WITH HIS RT FOOT PUTTING HIS BODY WEIGHT ON WRENCH WHEN W RENCH FELL OFF THE LOCK NUT CAUSING EMPLOYEE TO COME DOWN ON HIS RT FOOT CAUSING A SPRAIN TO THE FOOT

THE EMPLOYEE AND TWO OTHER CO-WORKERS WERE ATTEMTPING TO REMOVE A METAL FEED PLATE FROM A SCREEN. THE EMPLOYEE USED A PRY BAR WITH HSI RIGHT HAND WHILE HOLDING THE PLATE WITH HIS LEFT HAND. THE PLATE SLIPPED RUSHING THE TIP OF THE EMPLOYEE'S FINGER AGAINST THE FRAME. THREE-FOURTHS OF ONE INCH OF THE FINGER TIP WAS LATER AMPUTATED.

CUTTING HOSE WITH KNIFE, IT SLIPPED CUT EMP ON L THUMB.