Esta búsqueda
Envíame un correo cuando un nuevo incidente coincida con estos filtros. Un correo de confirmación; cancela la suscripción cuando quieras.
Dust from grinding got under contact lens. Employee was wearing safety glasses. Notified 4/21/2006
Employee was using his finger to remove a nut that was stuck in the socket of an impact wrench when he accidently turned the impact wrench on. This drove the nut onto his left index finger.
Team member was cutting approx. 8 inches off a 4 foot piece of 8 inch pipe. the balance of the 4 foot piece fell from the pipe stand and landed on the team member's right foot.
Changing a blow line from 1 pipe to another. There was no air pressure on the line when the accident occurred. The line slipped off the pipe, whipped around and hit EE in the face. EE has a deviated septum; will have open nasal reduction surgery 08/10/04.
EMPLOYEE WAS LYING ON HIS LEFT SIDE USING A CUTTING TORCH TO BURN A HOLE IN THE GROUND. AS HE WAS BLOWING THE HOLE, A PIECE OF HOT SLAG GOT IN HIS EAR.
HIS FAILURE TO PROPERLY POSITION HIE FEET WHILE TURNING THE DRUM CAUSED HIS FOOT TO SLIDE BETWEEN THE DRUM AND THE CRUSHER WALL.
EE WAS OPERATING A PNEUMATIC HAMMER ON CEMENT. FLYING DEBRIS WAS ABLE TO ENTER RT EYE DESPITE EE HAVING ON SAFETY GLASSES
ROCK FALL FROM ROOF COLLAPSED CAB OF TAMROCK MINIMATIC DRILL KNOCKED EE TO THE FLOOR.
EMPLOYEE WAS GRINDING METAL WITH POWER GRINDING WHEEL WHEN A PIECE OF METAL SEPERATED AND FLEW UNDER HIS SAFETY GLASSES ENTERING HIS RIGHT EYE.TREATED AND RELEASED FROM MED CENTER E.R. NO PERMANENT DAMAGE OR IMPAIRMENT.
EE AND OTHER WERE TRIMMING OVERHANGING LIMBS AND VINES FROM THE PIT HAUL ROAD. OTHER WAS CUTTING WITH A CHAIN SAW AND EE WAS RUNNING THE MANLIFT. JUST AS OTHER WAS CUTTING SOME VINES, EE REACH ED FOR THE VINE BEING CUT. HIS LEFT HAND WAS CUT HIS LEFT HAND WAS CUT IN THREE PLACES.
EE WAS ATTEMPTING TO INSTALL HI-PRESSURE PLUG IN BOTTOM OF TRACTOR BLOWER, IN THE DARK & IN AN ATTEMPT TO INSERT PLUG STUCK INDEX FINGER, L HAND, INTO PLUG HOLE WHERE IT WAS CAUGHT BETWEEN HOL E LIP & BLOWER ROTOR, AMPUTATING TIP. HE HAD SHUT DOWN TRACTOR & BLOWER & BLED AIR FROM FRUEHAUF TANK. HE FAILED TO REALIZE THAT LINE FROM TANK TO BAG HOUSE, WITH TRACTOR BLOWER DOWN, CAUSED
THE MECHANIC WAS WORKING WITH ANOTHER MECHANIC TO REMOVE THE OUTER NUT FROM A WHEEL RIM STUD WITH INNER AND OUTER NUTS. THE KEN TOOL WAS USED TO HOLD THE OUTER FROM TURNING WHILE AN AIR IMPACT WRENCH WITH SOCKET SPINS THE STUD OFF TO THE INWARD DIRECTION. THE KEN TOOL SLIPPED WHEN THE AIR WRENCH WAS ENGAGED AND SPUN AND STRUCK THE MECHANIC ON THE LEFT INDEX FINGER CAUSING A LACERAT
EMPLOYEE WAS REMOVING A BOLT FROM AN ELEVATOR WITH AN ELECTIRC IMPACT WRENCH WHEN HIS OFF HAND(LEFT) INDEX FINGER WAS LACERATED ON THE SHEARED JAGGED EDGE OF THE BOLT. TWO SUTURES WERE USED TO CLOSE THE LACERATION.
EMPLOYEE WAS SHARPENING SOAP STONE ON THE SIDE OF ROTATING GRIND ROCK WHEN THE SOAP STONE BROKE LETTING HIS FINGER CONTACT THE STONE CAUSING A LACERATION OF THE SECOND FINGER OF THE LEFT HAND . TWO SUTURES WERE USED TO CLOSE THE LACERATION.
EMP WAS OPERATING A DRILL OBTAINING ORE SAMPLES.EMP CONTACTED THE ROTATING BIT AND THE LEATHER GLOVE HE WAS WEARING WAS CAUGHT BY THE BIT, PULLING HIS RIGHT ARM TO THE BIT CAUSING A LACERATION TO HIS RIGHT FOREARM. THE WOUND REQUIRED CLEANING AND SUTURES TO CLOSE.
EE WAS HOLDING PIECE OF METAL BEING CUT. FORCE OF O2 USED IN CUTTING PROCESS DISLODGED DEBRIS ON AND AROUND METAL. FLYING DEBRIS ENTERED EE'S EYE UNDER SAFETY GLASSES.
EE WAS BAGGING MICA & TOOK A STEP BACKWARDS, SETLEFT FOOT TOWARDS OUTSIDE USING ALL HIS BODY WEIGHT ON LEFT LEG WHEN HE TURNED CAUSING MUSCLE STRAIN.
EE WAS USING A BAR TO HOLD THE FRICTION BAND ON HTE DRAG DRUM. THE FRICTION BAND SLIPPED, CATCHING EE'S LEFT THUMB BETWEEN THE BAR AND THE FRICTION BAND. THE THUMB WAS MASHED AND IT TOOK 8 STI TCHES TO SEW UP THE CUT.
EE WAS USING AN AIR IMPACT TO REMOVE A BROKEN SPRING FROM A SHAKER SCREEN. WHEN THE LAST BOLT WAS REMOVED THE SPRING FELL AND HIT EE S LEFT HAND.
EMPLOYEE WAS ASSISTING IN RE-LINING MIEN FLOAT CELLS, WHILE HOLDING LINING TO BE DRILLED HE PLACE DHIS HAND OVER AN ALREADY DRILLED HOLE. THE DRILLER UNABLE TO SEE LGITH THRU THE HOLD THOUGHT HE HAD NOT COMPLETED THE DRILLING REDRILLE DHTE HOLE CONTACTING THE HOLDERS HAND.
TEAM MEMBER WAS USING CUTTING TORCH TO CUT PLATE METAL WHEN HE HAD A BLOW BACK & A PIECE OF SLAG FLEW INTO LEFT EYE
EE WAS BAGGING POLYMICA 325. HE WAS CHECKING FOR DISCOLORED MICA. HE PLACED HIS FINGER AT THE BASE OF THE BAGGING TUBE. THE REVERSE SCREW WAS STILL IN MOTION AND PULLED HIS FINGER INTO THE TUB E OF THE BAGGING MACHINE. BEFOR THE AUGER STOPPED, EE WAS ABLE TO PULL HIS FINGER OUT OF THE TUBE. EE SUSTAINED A LACERATION TO THE RIGHT INDEX FINGER WHICH REQUIRED SEVEN (7) STITCHES.
EE WAS BAGGING POLYMICA 325. HE THOUGHT THE MICA LOOKED GREY. HE PLACED HIS FINGER ON THE TUBE OF THE BAGGING MACHINE TO CHECK THE COLOR. WHILE DOING THIS, THE REVERESE SCREW WAS STILL IN MOTI ON AND PULLED HIS LEFT INDEX FINGER INTO THE TUBE OF THE BAGGING MACHINE. SUSTAINED A LACERATION, WHICH REQUIRED FIVE STITCHES, AND HIS BONE WAS GROVED LENGTHWISE.
WAS HOLDING PIPE WHILE IT WAS BEING CUT GOT OVERBALANCED AND LID INTO H BEAM GOT CUT BEHIND RIGHT EAR.
A SMALL PIECE OF METAL ENTERED LEFT EYE DURING GRINDING OPERATION A RIGHT ANGLE GRINDER WAS USED TO SURFACE A WILLIAMS MILL JOURNAL GLASSES WERE BEING WORN
EE WAS DRILLING HOLES IN A ROUND STEEL FLANGE WHEN THE DRILL BIT CAUGHT IN THE METAL THIS CAUSED THE FLANGE TO SPIN THEREBY STRIKING THE EE IN THE LEFT WRIST CAUSING A LACERATION ON THE RADIAL SIDE INJURY REQUIRED SUTUTURES.
EMPLOYEE WAS DRILLING FACE WHEN SOME STONE FELL FROM FACE EMPLOYEE STOOD UP TO SEE IF STONE WAS HITTING BOOM OF DRILL ON THE PROCESS EMPLOYEE HIT HEAD ON TOP OF CAB & JAM NECK MUSCLES
USING AN AIR-ARC WELDER TO CUT METAL,A PIECE APPROX 200U IN DIAMETER ENTERED RIGHT EYE.INCIDENT WAS NOT IMMEDIATELY DUE TO SMALL SIZE OF PARTICLE.PARTICLE STAYED IN EYE FOR EXCESS OF 24 HOURS AT WHICH TIME IT RUSTED AND BEGAN CAUSING PAIN AND DISCOMFORT.SAFETY GLASSES WERE WORM UNDERNEATH WELDING HOOD.EXACT CAUSE UNKNOWN.
EMPLOYEE WAS USING A JACKHAMMER TO CRACK OPEN AN AREA OF CONCRETE WHICH NEEDED REPAIRING WHEN LIFTING HAMMER TO MOVE EMPLOYEE EXPERIENCED PAIN IN HIS RT MIDDLE BACK
THE MATERIAL DISCHARGE CHUTE BELOW THE 66 MILL CYCLONE HAD BECOME PLUGGED OR BLOCKED OFF,THE ASST OPERATOR INSPECTED THE CHUTE TO CORRECT THE BLOCKAGE BY REMOVING THE SAMPLE PORT AND STICKING HIS HAND AND ARM INTO THE SAMPLE PORT.THIS WAS DONE WITHOUT SHUTTING OFF THE ROTARY VALVE.TO CONTACT THE ROTARY VALVE THE ASST OPER MUST HAVE REACHED UPWARD CAUSING HIS FINGERS TO BE SEVERED B
EMPLOYEE WAS OPERATING A D-4 DOZER TO PUSH UP CLAY PILES.WHILE BACKING OFF CLAY PILE THE DOZER RAN OVER A LUMP OF CLAY AND DOZER TRACK CAME DOWN ON CONCRETE PAD JARRING THE EMPLOYEE AND CAUSIN G PAIN TO LOWER BACK.EMPLOYEE REFUSED TO GO TO THE DOCTOR AT THIS TIME.EMPLOYEE TOLD HIS FOREMAN ON MARCH 4,1991 THAT HIS BACK WAS STILL HURTING AND HE WAS SENT TO THE DOCTOR.
EMPL CARRYING 6' PIECE OF DRILL STEEL ON TRACK DRILL AS IT WAS BEING MOVED.STEEL FELL OFF,EMPL BENT OVER TO PICK IT UP.AS HE REACHED FOR IT THE TRACK DRILL SETTLED BACKWARD SLIGHTLY ROLLING ON TO STEEL.THIS MASHED DRILL STEEL DOWN ON TOP OF EMPL FOOT.
USING GRINDER TO CLEAN SURFACE METAL A FOREIGN OBJECT ENTERED HIS EYE.
EE DRILL WAS STRUCK BY A ROCK FALLING FROM THE ROOF. THE ROCK HAD BEEN CHECKED AND WAS BELIEVE TO BE SECURE. THE IMPACT SHOOK THE DRILL CAUSING THE EE TO FALL TO THE CAGE FLOOR HITTING HIS LEF T LEG AT THE KNEE AGAINST THE FLOOR CONTINVAL PAIN LOW LEVEL LED THE EE TO SEEK TREATMENT AT THIS LATER DATE. EE WAS RESTRICTED DUTY FOR 10 DAYS DURING THIS TREATMENT.
EMPLOYEE WAS USING JACK HAMMER TO DRILL THROUGH A CONCRETE FOUNDATION WHEN HE GOT CRET PAIN AND SICK. HE VOMIT AND NOSE BLEED.
CLEANING EQUIPMENT WITH HIGH PRESSURE AIR WHEN FOREIGN OBJECT BLEW INTO HIS EYE.
EMPLOYEE WAS WELDING ON PIPE IN DRY PLANT.AFTER HE HAD FINISHED WELDING AND HAD PUT AWAY HIS EQUIPMENT AND REMOVED HOOD,HE LATER TURNED TO PUT CLAMP ON PIPE AND WHILE DOING SO,A SMALL PIECE OF SLAG POPPED OFF INTO EMPLOYEES LEFT EYE PUPIL.
EMPLOYEE WAS MOVING DRILL FROM ONE HEADING TO ANOTHER 100 FT AWAY WHEN THE DRIVE SHAFT CAME OUT AND THE BRAKES FAILED. THE DRILL ROLLED BACKWARD AND STRUCK A PILLOW. THE EMPLOYEE S NECK WAS SH IP LASHED WHEN THE DRILL STRUCK THE PILLOW. EMPLOYEE WENT TO DR ON 2-6-89 AND STARTED LOSING TIME SAME DAY.
EMPLOYEE WAS ASSISTING MECHAINC TO P OSITION REAR END UNDER TRUCK FRAME WHILE FORKLIFT (WHITEMA40)RAISED UNIT IN PLACE THE REAR END SLID ON FORKLIFT FORKS AND EMPLOYEES HAND WAS MOM ENTARILY CAUGHT BETWEEN REAR END HOUSING AND BOTTOM OF THE TRUCK FRAME CAUSIONG THE INJURY.
EMPLOYEE WAS WORKING IN WELDING SHOP AREA ON THIS DAY USING ELECTRIC RIGHT-ANGLE GRINDER AND ACETYLENE TORCH TO REMOVE WORN CONVEYOR FLIGHTS FROM CENTRIFUGE CONVEYOR. HE WAS WEARING PROPER SA FETY GLASSES/GOGGLES/FACE SHIELD FOR JOBS HE PERFORMED. EMPLYEE ON 09/16/88 COMPLAINED OF FLASH BURNS TO BOTH EYES - RECEIVED MEDICAL ATTENTION OPTH. OINTMENT AND PATCH.
EMPL WAS USING SIDE GRINDER TO CLEAN TORCH CUT STEEL PLATE EDGES & FOREIGN OBJECT CONTACTED HIS LEFT EYE.
CHANGING DRILL 8TEEL AFTER DRILLING NEXT TO PILLAR AND A ROCK FELL FROM 10' AND STRUCK HIM ON RIGHT SHOULDER.
EE WAS ASSISTIN1 WELDER IN WELDING 4" PIPES TOGETHER WITH PORTABLE GASOLINE ARC WELDER & WAS SUBJECTED TO WELDING FLASH WHICH CAUSED BURNS TO EE'S EYES.
A SPARK FLEW OF0 OF THE METAL BEING GROUND DOWN ON THE GRINDING WHEEL HE HAD GOGGLES & A GUARD IN USE
ONE TRACK START9D UP A SMALL INCLINE PUTTING THE MACHINE IN A BIND.A BRACE FROM THE POWER AXLE TO THE UNDER-CARRIAGE BROKE AND LET THE MACHINE TURN OVER ONTO ITS SIDE.THE OPERATOR'S RIGHT FOOT WAS PINNED BET4EEN THE MACHINE AND THE GROUND.
EMPLOYEE WAS AT7EMPTING TO START GASOLINE ENGINE BY PULLING ROPE STARTER CORD ON PRESSURE WASHER AND STRAINED BACK MUSCLE
WELDERS HELPER 8ID NOT PROPERLY PROTECT HIMSELF FROM WELDERS ARC.
EE REMOVED V/BELT DRIVE GUARD ON BAGGING MACHINE FOLLOWING ELECTRIC FAILURE TO PRODUCT MATERIAL BLOCKAGE IN MACHINE. AFTER REMOVING GAURD EE MANUALLY TURNED V-BELT DRIVE TO FREE THE BLOCKAGE & A SECOND EE ASSISTING IN REPAIR MISTAKENLY RESET ELECTRIC SWITCH CAUSING MACHINE TO START. 1ST EES LEFT INDEX FINGER CAUGHT IN V-BELT DRIVE RESULTING IN THE INJURY.
GILL WAS ENLARGING A BOLT HOLE WITH A CHIPPING HAMMER, A CHIP OF THE CHIPPING HAMMER FLEW UP HITTING JAMES ON THE BACK OF THE HAND.
2 MEN WERE CLEANING INSIDE A ROD MILL SHELL. RICHARD\S GOGGLES FOGGED UP. RICHARD RAISED HIS GOGGLES TO REMOVE MOISTURE FROM THE INSIDE SOMETHING FROM THE OTHER MAN\S CHIPPING GOT INTO RICHARD \S EYE.