Buscar en el registro

EMPLOYEE WAS FEEDING BAG FILM INTO BAG ADVANCE BELTS ON BAG MACHINE. WHEN HE ADVANCED MACHINE, IT PULLED HIS MIDDLE FINGER (LEFT HAND) INTO "V" BELTS. HE WAS HOLDING CRIMPED END ON TOP INSTEAD OF AT BOTTOM AWAY FROM PINCH POINT. I BANDAGED HIS FINGER - EMPLOYEE FINISHED HIS SHIFT. HE WAS SORE FOR NEXT FEW DAYS. NO WORK RESTRICTION, NO LOST TIME. HE WENT TO DR ON HIS OWN RECD STITCH

EE WAS WELDING AND GRINDING ON A CRACKED CROSS MEMEBER OF A TRANSFER. HE HAD LIMITED ACCESS. HE WORE SAFETY GLASSES AT ALL TIMES HOWEVER HE DID NOT WEAR A SHIELD A TALL TIMES BECAUSE OF TIGHT ACCESS. THE NEXT MORNING HE FELT SOMETHING IN HIS LEFT EYE. IT WAS REMOVED AT THE CLINIC THAT DAY. RELEASED TO FULL DUTY.

WHILE REMOVING A CYLINDER ON A P&H DRAG LINE A BOLT FLEW OUT AND HIT RIGHT CHEEK OF EE CAUSING LACERATION.

EE WAS CUTTING A PIECE OF 1 1/4" PIPE WITH A PORTABAND SAW. WHEN THE SAW CUT THROUGH, EE'S HAND WAS CUT BY PIPE.

EE WAS OPERATING DREDGE WHEN HE INADVERTENTLY STRUCK RIGHT ELBOW ON A LEVER CAUSING TEMPORARILY NUMBNESS TO RIGHT ARM.

DRILLING BOULDER, WENT TO MOVE THE BOOM OFF THE BOULDER, IT SLIP DOWN AND PINCHED HIS FINGER.

EE WAS USING A 9" GRINDER ON FEEDER BED WHEN HE STRUCK HIS LEFT KNEE CAUSING A LACERATION.

EMPLOYEE WAS WATERBLASTING ON THE FEED SHELF WHEN HOT MATERIAL GOT UNDER HIS GLOVE AND SLEEVE CAUSING 1ST AND 2ND DEGREE BURNS.

EE WAS WORKING ON NEW TYPE POSITIONING VALVE ON #44 SILO. THE VALVE HAD TO REMAIN ENERGIZED DUE TO THE WORK THAT WAS BEING DONE. EE BEGAN THE CYLINDER TO THE VALVE HE FORGOT TO SHUT OFF THE AIR THAT POWERED IT. WHEN HE STUCK HIS FINGERTIPTHROUGH THE CLEVIS TO ALIGN EVERYTHING THE CYLINDER RETRACTED CUTTING OFF FINGERTIP. NO BONE INVOLVED.

EMPLOYEE WAS LUBRICATING THE WALKING CAM OF THE DRAGLINE. EMPLOYEE'S HAND WAS PINCHED BETWEEN THE CAM AND FRAME.

TWO MECHANICS WERE WORKING ON THE #2 AIR SLIDE. THEY HAD NOT DISENGAGED THE AIR VALVE OR SHUT THE MANUAL SLIDE GATE. WHEN THE LOADOUT OPERATOR RETURNED FROM A SAFETY CLASS & TOOK OVER LOADING TRUCKS, HE DID NOT KNOW THE MECHANICS WERE WORKING ONT HE AIR SLIDE. HE SWITCHED THE KNOB TO LOAD OUT OF #2.

TWO MECHANICS WERE WORKING ON THE #2 AIR SLIDE. THEY HAD NOT DISENGAGED THE AIR VALVE OR SHUT THE MANUAL SLIDE GATE. WHEN THE LOADOUT OPERATOR RETURNED FROM A SAFETY CLASS & TOOK OVER LOADING TRUCKS, HE DID NOT KNOW THE MECHANICS WERE WORKING ON THE AIR SLIDE. HE SWITCHED THE KNOB TO LOAD OUT OF #2.

EE WAS MOVING DRILL FROM ONE SHOT TO ANOTHER, HE STOPPED, AT THE TOP OF THE HILL FOR TRACKS TO MOVE, HE PROCEDED DOWN THE HILL ABD STARTED TO MOVE FASTER, HE ATTEMPTED TO APPLY THE BRAKES BUT DRILL WAS MOVING TOO FAST TO STOP. HE DROVE IT ONTO THE BERM TO STOP IT. DRILL STOPPED IN SLOW MOTION AND ROLLED OVER.

WHILE OPERATING MOBILE CRANE IN TRANSIT TO PIT, CRANE STRUCK BERM AND OVERTURNED ON SITE, PINNING OPERATOR INSIDE CAB FOR ABOUT 40 MIN.

AFTER HOLED DRILLED, DRILLER FORGOT TOREMOVE RUBBER DUST COVER FROM ROD; LOOKED UP TO WATCH HEAD OF DRILL & SWING ROD INTO CAROUSEL. AS HE LOOKED UP THE FALLING RUBBER COVER STRUCK HIM THE FAC E KNOCKING OFF HIS SAFETY GLASSES & HARD HAT. HEWAS TAKEN BY CO. VEHICLE FOR EMERGENCY CAREA; WAS RELEASED WITH NO BROKEN BONES; NO STITCHES; NO CONCUSSION. WAS TOLD BY ATTENDING PHYSICIAN HE

WHILE USING A GRINDING WHEEL, THE WHEEL CAME OFF AND CUT EMPLOYEE ON LEFT FOREARM.

LAYING ON SIDE GRINDING A SCREEN BODY SIDE, PREPARING TO WELD--GLASSES FOGGED, SLID DOWN ON NOSE BY EE, PIECE BOUNCED AND LODGED IN EYE.

SUPERVISOR WAS HELPING ANOTHER DEPT TO DISABBEMBLE A PUMP. THE BRAKE ASSEMBLY BREAKING WERE STUCK. WHEN THE ASSEMBLY WAS LOOSENED IT WENT TO REVERSE CATCHING HIS THUMB DUE TO UNKNOWN PRESSUR E IN THE BASE OF THE PUMP.

WHILE SLAG DROPPED AND LODGED ON THE OUTER TONGUE OF BOOT WHICH BURNT A HOLE CAUSING PENETRATION OF THE SLAG INSIDE. THIS CAUSED A COMBUSTION REACTION INSIDE THE BOOTS WHICH CHARRED SOCK AND B OOT THEN CAUSED SKIN DAMAGE.

WHILE OPERATING AN END GRINDER, WITH A CUT OFF WHEEL ATTACHMENT, THE GRINDER KICKED BACK AND THE WHEEL LACERATED THE ARM.

EE WAS HIT ON HIS HARD HAT BY A ROCK WHICH WAS THROWN OUT OF THE CRUSHER.

EMPLOYEE WAS WELDING WHEN A PIECE OF SLAG FELL INTO HIS BOOT AND BURNED HIS RIGHT FOOT.

WHILE ADJUSTING A JACK STAND, THE JACK SLIPPED AND PINCHED EMPLOYEE'S 2 FINGERS BETWEEN THE PIPE AND THE STAND.

EMPLOYEE WAS CUTTING A BOLT OFF IN THE PLANT ANDA PIECE OF HOT METAL FELL INSIDE HIS RIGHT BOOT AND BURNED HIS FOOT.

DRILLER WAS PUTTING A NEW BIT ON THE ROD, THE WRENCH SPUN AROUND AND HIT HIS HAND CUTTING THE POINTER FINGER ON HIS LEFT HAND.

EE WAS WAITING TO BACK UNDER RIP RAP LOADER. HE WAS SETTING ABOUT 50 TO 100 FT AWAY FROM HAMMER BREAKER. EE HAD WINDOW DOWN ABOUT 6 INCHES ON PASSENGER SIDE. HE HAD PIECE(SMALL) ROCK FLY INTO SIDE WINDOW. IT HIM ON HIS RIGHT SIDE OF HEAD.

EE DEVELOPED BACK PAIN WHILE OPERATING BULLDOZER.

EE WAS HGRINDING METAL. HE LIFTED THE SHIELD AND GLASSES AND SOME MATERIAL FELL INTO THE EYE.

EE WAS OUTSIDE SHOP. SNOWING & RAINING. EE WAS AIR ARCING THE BLADE OF D9. THE BLADE WAS ABOUT 12" OFF GROUND. HE WAS ON KNEES AND LIFTING HOOD TO TAKE A LOOK AT WORK WHEN A PUDDLE OF SLAG POP PED. HE WAS WORKING ALONE AND ON THE WAY HOME INTHE DARK HAD IMPAIRED VISION. WENT TO ER THAT NIGHT.