Buscar en el registro

While walking towards the jaw feeder, the employee grabbed the frame to brace self and cut EE's finger on a sharp edge

Welding on jaw of crusher, after shift realized scratching in eye from foreign object due to welding.

While removing a bearing, employee struck self in face with hammer

Cut left palm from changing cutting edge bolts

Smashed finger between steel frame and prybar while trying to remove built up material from a roller.

While freeing up a brake system, piece of rust got into employees eye.

While lowering a light on a electrical box, the light came down and hit their jaw, fracturing a molar tooth.

Employee was adding a fellow employee who had fallen to their feet and injured their head/neck and lower back.

Piece of metal got into employees' eye sometime during shift, unknown how it happened.

Employee was cutting flashing with a knife, knife slipped and cut EE's leg. Took several stiches to close the laceration.

Employee pinched EE's finger between two metal stands while moving the stands.

Operator rubbed EE's eye and got a small piece of metal in EE's eye. Next day eye was swollen and doctor had to grind a piece of metal out of the operators eye.

Operator set down a grinder while cutting disk was still spinning, disk contacted the conveyor belt and jumped to the side. The spinning disk contacted the back of the operators hand and caused a laceration to the hand. Laceration required stiches to close.

Employee tripped over a pallet, fell to ground and caused a contusion to right arm.

Employee was striking a steel pin when a metal shard broke off and embedded in EE's leg. After metal shard was removed, a stitch was required to close the laceration.

Operator fell down a flight of steps and broke left arm.

EE was installing a tire on equipment when their middle finger got caught between the snap wire and the rim flange causing an injury and cut on the right middle finger.

Employee fell over a ladder and landed on shoulder and back.

Flash burn to eyes while doing maintenance.

Operating haul truck and felt back go out.

Operator jarred EE's back while operating front end loader.

Lower back pain from operation haul truck on rough road.

Employees were performing maintenance on a crusher screen. One employee inadvertently struck partners finger with a hammer while installing screen clamp bolts. The injured employee has an open fracture of the left middle distal phalange.

Using a grinder to remove a bracket and at some point got a piece of steel in their eye.

Operator was stepping down from catwalk to another, stepped wrong and twisted knee and fell onto catwalk.

Using air nozzle to blow away debris, small piece got into left eye.

Holding cutting edge bolt in place, impact wrench caused bolt to spin and cut index finger on employee.

Finger was pinched when wrench slipped resulting in a laceration to the left index finger tip. Took 6 stitches to close wound.

Employee was lifting a heavy rock, dropped the rock and it rolled into EE's right ankle.

Employee was standing on a step ladder shoveling off a conveyor, ladder shifted and employee fell backwards to the ground.

Operator had EE's hand pinched between a head pully and a bracket, resulting in a cut that required stitches to close the wound.

Employee had a small piece of metal blow into their eye and become embedded.

Employee was loosening a bolt with impact wrench. Employee tried to hold bolt in place with hand, when bolt head spun and cut hand.

Pounding in silt fence and felt tightness in neck afterwards.

Operator fell over a block of wood while walking backwards, falling down on EE's right elbow.

Carrying ANFO to drill holes from pallet & stemming holes. Bags of ANFO weighed 50 lbs each. Tenderness felt @ 11:00 AM (described as muscle ache). Incident did not get reported until 10/12/22 (when medical evaluation was sought).

Striking a piece of metal with a hammer, small shard of steel flew off and struck the miner in the knee. Operator needed surgery to remove the piece of steel and four stitches to close the wound.

After standing on their feet all day, operator felt tightness in their back and numbness in their legs.

Operator was running to shut down a conveyor and felt a pop in lower back.

Operator was using a cut-off wheel and disk came apart. Small section struck operator in the stomach, requiring 4 stitches to close the laceration.

Stood up while working under wash plant and suffered a neck contusion when head struck wash plant.

Employee was pulled sideways while moving a screen and fell on EE's left shoulder.

Operator was stepping down in to the feeder and hyper extended knee.

Cutting a section of conveyor belt with a knife, knife slipped and operator cut leg needing stitches to close the wound.

Employee was assisting to remove cutting edge bolts from a loader bucket that was properly blocked & locked out. Employee failed to use PPE. Since injury we have retrained employee as well as gave additional task training. Employee got EE's finger cut which required five stitches. No long term impairment.

Laceration to left wrist

Metal guard fell and struck operator in the head, causing a laceration needing staples to close.

Operator was struck in the hand while releasing the handle on a ratchet strap. Impact from the handle fractured Operator's thumb.

Employee was walking around truck when left foot broke through the ice. Employee's right foot slipped on the ice and employee fell to the ground breaking lower leg.

Employee smashed a finger while moving blocking.