Buscar en el registro

CRUSHER LABORER JUMPED OFF A PILE OF DIRT & STRAINED HIS RIGHT KNEE. HE THOUGHT HE WOULD BE ALRIGHT SO HE DIDN'T REPORT THE INCIDENT. HIS KNEE CONTINUED TO BOTHER HIM SO HE WENT TO THE DR TO H AVE IT CHECKED.

EMPLOYEE WAS PUTTING CURTAIN LINERS IN CRUSHER &DROPPED ONE ON HIS RIGHT RING FINGER SMASHING THE NAIL. IT REQUIRED ONE STITCH.

EMPLOYEE WAS CLEANING UNDER JAW AND A ROCK HIT HIM IN THE HEAD REQUIRING 6 STITCHES.

EE STEPPED OFF OF LOADER AND TWISTED HIS KNEE REQUIRING KNEE SURGERY.

EE WAS LIFTING SOME WIRE TO REBUILD THE DRY SCREEN DISCHARGE CHUTE AND STRAINED HIS GROIN (RIGHT).

EE WAS REPLACING THE REAR END OF THE EUCLID R-40ROCK TRUCK AND HIS HAND SLIPPED CUTTING HIS 3RD FINGER ON RIGHT HAND REQUIRING 3 STITCHES.

EE WAS DISMOUNTING A SKID LOADER. HE STEPPED ON A ROCK AND SPRAINED HIS LEFT ANKLE. HE WAS JUST FINISHING HIS SHIFT, ON HIS WAY TO THE CRUSHER OFFICE TO CHECK OUT. THE SUN WAS ALMOST UP.

WHILE HAULING ROCK FROM THE PIT TO THE PRIMARY JAW IN THE 465 ROCK TRUCK, EMPLOYEE HIT A BUMP AND JARRED HIS LOW BACK.

CLEANING CRUSHER RUN CHUTE HE CUT 4TH FINGER ON RIGHT HAND ON SCREENS REQUIRING 3 STITCHES.

EMPLOYEE WAS INSTALLING V-BELT ON DRIVE MOTOR TO CRUSHER. SLIPPED ON MOTOR LANDING, AS HE CAUGHT HIS BALANCE HE SLIGHTLY STRAINED HIS LOWER BACK.

EMPLOYEE WHILE PULLING CABLE, STEPPED ON SOFT DIRT CAUSING A KNEE STRAIN. LATER EXAMINATION REVEALED A TORN ACL WHICH REQUIRED SURGERY.

EMPLOYEE WAS USING UTILITY KNIFE TO CUT BELTING WHEN THE KNIFE SLIPPED AND CUT HIS FINGER. HE SUSTAINED 9 STITCHES IN FINGER.

EE WAS WELDING W/ARCH WELDER HE STOPPED WELDING, RAISED HOOD AND BEGAN PRYING ON PLAT S/PRY BAR. THE PRY BAR SLIPPED, STRIKING EE IN EYE. SAFETY GLASSES WERE PROVIDED TO EE PRIOR TO ACCIDENT.

EE WAS WELDING ON TRACKHOE AND HE RAISED HIS FACE SHIELD TO CHANGE WELDING RODS AND THE STINGER ARCED CAUSING A FLASHBURN.

EE HELPING TO MOVE A BARREL OF ANTIFREEZE ONTO RACK WHILE PUSHING BARREL L KNEE POPPED OUT OF JOINT

EE WAS MOVING A GRIZZLY BAR. AS HE LIFTED THE BAR HE STRAINED HIS LOWER BACK.

EE DISMOUNTED BACKHOE ON UNLEVEL SURFACE. AS HE WAS WALKING AWAY FROM BACKHOE HIS RIGHT ANKLE GAVE WAY ON UNEVEN SURFACE.

WORKING ON CHUTE OF WASHPLANT. BROKE OFF & FELL ON LEFT UPPER ARM ABOVE THE ELBOW. PUNCTURED ARM & CAUSED SEVERE BLEEDING

EMPLOYEE WAS SEATED ON A CHAIN IN THE CRUSHER IN THE CRUSHER CONTROL ROOM. THE CHAIR BROKE AT THE BASE, HE FELL, HITTING HIS HEAD ON THE WALL OF THE OFFICE. HE SPRAINED HIS NECK, AND RECEIVED A BRUISE TO HIS HEAD.

EE CLAIMS THAT HE STRAINED SHOULDER AND BACK WHILE REPAIRING A BELT. HOWEVER, HE DID NOT REPORT ANYTHING UNTIL THE 11TH OF SEPTEMBER. HE STATES THAT AS HE WAS STEPPING ONTO THE GROUND, HE LOST HIS BALANCE, GRABBED A RAIL TO REGAIN BALANCE AND STRAINED HIS SHOULDER.

EE WAS REMOVING JAW DIE WEDGE WHEN THE PORTA-POWER CYLINDER SLIPPED AND MASHED HIS RIGHT INDEX FINGER.

EE WAS CLIMBING UP ON FENDER TO INSPECT FOR LARGE ROCK. HE SLIPPED ON A LOWER BEAM & FELL SIDEWAYS ONTO HIS RIGHT SIDE CAUSING INJURY. HE FELL APPROX 21/2 FT ONTO A LARGE ROCK

STRAINED LIGAMENTS IN LEFT KNEE, WHEN HE STEPPED ON SOME ROCKS HE WAS REMOVING FROM THE CATWALKS.

CHANGING JAW DIE AND PUTTING THROAT BACK OVER JAW, THE CHAIN WAS TOO LONG SO THEY WERE GOING TO REHOOK IT, EMPLOYEE WAS TRYING TO GET OUT OF THE WAY AND STUMBLED GRABBING A BAR AND THE THROAT SMASHED RIGHT INDEX FINGER.

AS EE WAS CLIMBING DOWN FROM A FEED BELT, HE MISSED HIS FOOTING AND FELL. EE FELL AGAINST A SUPPORT BEAM STRIKING HIS LOWER BACK. *IT SHOULD BE NOTED THAT EE DID NOT REPORT THIS ACCIDENT TO TH E EMPLOYER UNTI 7-31-00.

EMPLOYEE WAS DISMOUNTING DOZER. HE TWISTED HIS LEFT KNEE WHILE CLIMBING DOWN OFF THE D-10 DOZER. HE SAYS HE WAS USING THE 3-PT. CLIMBING TECHNIQUE. HE JUST LOST HIS BALANCE WHEN HE REACHED THE GROUND LEVEL. THE GROUND SURFACE WAS FLAT AND SMOOTH.

SLIPPED & HIT ARM ON FRONT OF LOADER WHILE CHECKING VOLTAGE

REMOVING PULLEY FROM CONVEYOR ON WET DECK, PULLEY SLIPPED AND CUT EE ABOVE LEFT WRIST.

EMPLOYEE WAS LIFTING A HEAVY METAL GRIZZLY BAR THAT HAD FALLEN INTO THE CONE (THE CRUSHER WAS STOPPED). EMPLOYEE STRAINED HIS BACK.

STEPPED OFF LADDER ONTO GROUND (WHICH WAS FLAT) AND TWISTED RIGHT LEG.

LIFTING STARTER FROM WATER TRUCK, FELT PAIN IN R SHOULDER.

WHILE CLEANING OUT CHUTE ON PRIMARY CRUSHER (PRYBAR USED TO DISLODGE ROCK), A ROCK DISLODGED ANDEMPLOYEE'S MIDDLE FINGER ON RIGHT HAND MASHED BETWEEN PRY BAR & CHUTE, REQUIRING 3-4 STITCHES.

EE WAS CHANGING THE TIRE ON A SKID STEER. HE WAS PLACING THE TIRE ON THE STUDS, IT SLIPPED OFF THE STUDS AND SMASHED HIS LEFT PINKY FINGER.

CLIMBING LADDER TO TIE OFF TO WORK ON PUG MILL. BEFORE HE WAS ABLE TO TIE DOWN LADDER MOVED CAUSING HIM TO SLIP/FALL HURTING LEFT LEG. (FELL 4-5') NO LOST TIME OR RESTRICTED DUTY UNTIL SURGERY WAS PERFORMED ON 11-27-00.

KNUCKLE ON RAILCAR WAS DEFECTIVE AND FELL OFF HITTING EE ON TOP OF R FOOT. (ABOVE STEEL TOE.)

EE SLIPPED ON A BEAM & HIT HIS RIGHT KNEE ON CONCRETE

LOADER BACKED INTO MANLIFT CAUSING PERSON TO FALL OUT. HE LANDED ON THE CAGE ON MANLIFT.

MOTION OF LOADER CAUSED NERVE IN BACK TO BECOME AGGRAVATED.

CUTTING CONVEYOR BELT (MASONERY MACHINE) WITH UTILITY KNIFE. BELT SLIPPED CAUSING KNIFE TO SLIDE & CUT EE. CUT RT. INNER THIGH WHICH HAD TO HAVE 3 STAPLES.

STEPPING DOWN FROM TRUCK, TURNED RIGHT ANKLE.

OPERATION OF LOADER DAYS PRIOR TO INJURY, WORKING IN SAND PIT, BEING JARRED.

WHILE CLEANING OUT CONE TRAILER, EE SLIPPED AND FELL.

WAS OPERATING A ROCK BREAKER ON A TRACK HOE. A PIECE OF FLYING ROCK HIT HIM IN THE R EYE. OPERATOR WAS NOT WEARING SAFETY GLASSES.

EE WAS PICKING UP A PIECE TO PUT ON THE ROCK HAMMER AND IT SLIPPED SMASHING HIS MEDDLE FINGER ON HIS LEFT HAND AND IT TORE THE NAIL OFF.

WHILE LOADING CUTTING EDGES INTO LOADER BUCKET, EE TWISTE AT THE SAME TIME HE WAS LLIFTING, INJURING LOWER BACK. HE WAS STANDING ON GROUND LEVEL LIFTING CUTTING EDGES & PUTTING THEM INTO THE B UCKET OF A LOADER.

EE WAS STEPPING OFF OF A BEL UNLOADER, SLIPPED ON A ROLLER, AND HIT RIBS AGAINST THE EDGE OF A LOADER BUCKET.

CONTRACTOR WAS WALKING ALONG A BERM TO GET INTO ROCK TRUCK AND LOST HIS FOOTING AND FELL DOWN A 50' EMBANKMENT INTO WASTE DUMP.