Buscar en el registro

EE was operating a Cat 988F end loader. Another end loader came around small pile of coal and struck the rear of the other loader.

EE was attempting to change the position of the flopgate at the head of the #2 raw coal belt. The flopgate had become wedged against a small bolt head inside of the chute.While using a prybar to dislodge the gate the bar slipped out of the EE's hands. He grabbed the bar as it fell and wrenched his shoulder. EE started missing work on 5/11/10.

Employee had parked a Cat 938 at the service dock for service. He decided to clean his front glass & stepped out onto the top of the wheel fender. As he finished, he grabbed the top of the light housing on the fender & it broke. He jumped to the ground when he lost his balance. Originally a knee sprain. Did not miss work until 7/7/10 for arthoscopic surgery

EE was operating a gob truck in the pit area. He was on his way out of the pit, hauling shale back to the gob dump at the Prep Plant, when he ran over a hole in the haul road causing him to go up and down very suddenly. EE did not start missing work until March 19,08. It was determined by the doctor he had trauma to the abdominal area.

Employee stated that he was mounting his Cat-777 end dump using the factory steps and hand rails. As he was reaching for the hand rail beneath the window of the cab (while standing on the 3" wide step) he lost his balance, spun around, and fell to the frozen ground.

Employee was attempting to remove bolt and nut from a flange coupling on a 6" feed line to belt press. He had a long ratchet w/ socket attached on one side and a 15/16" combinations wrench attached on the other side. The bolt and nut was seized (frozen), the ratchet slipped causing the wrench to move pinching his little finger between the wrench and the flange of the coupling.

After the completion of the investigation on April 10, 2007, it was determined that I was responsible for reporting the injury. Another vendor (salesman) was walking through the prep plant on the third floor where my employees where working and had removed a piece of grading to conduct some repairs on a I-beam and EE stepped into the hole.

Employee stated he had stomach cramps the week before. He had also tried to install a window air conditioner at home prior to the start of his shift. He thought he had drunk enough water. He felt a little faint after his shift started. He came out from under equipment and was kneeling when he felt faint again and lay down.

EMPLOYEE IS STATING HE WAS STEPPING BACK FROM FUELING A DOZER TO THE CONTAINMENT STRUCTURE AROUND A DIESEL FUEL TANK. HE LOST HIS BALANCE AND STEPPED DOWN TO A PLATFORM (APPROX 2') PUTTING HIS WEIGHT ON ONE LEG. THIS ACTION CAUSED AN INFLAMATION TO THE OSTEOARTHRITIC CONDITION OF HIS LUMBOSACRAL SPINE THAT HAS EXISTED FOR A PERIOD OF TIME.

EMPLOYEE IS STATING THAT HE WAS HELPING CHANGE HYDRAULIC LINE ON THE SHOVEL BOOM. HE IS STATING THAT HE SLIPPED ON BOOM STEPS & CAUGHT HIMSELF BY GRABBING A BANK OF HYDRAULIC HOSES & WRENCHED HIS RT. SHOULDER. EE IS STATING HE WORKED THE REST OF HIS SHIFT & PART OF THE NEXT SHIFT ON 8/3/04, HE THEN FELT HIS SHOULDER "POP" ON 8/3/04.

Employee is stating that he felt back pain on 4-16 and 4-21 while performing duties as a deckhand on a coal barge. Employee sought medical attention on 4-21. Ee had degenerative spine disease.

EE IS STATING THAT HE WAS OPERATING THE HITACHI EX1800 SHOVEL IN THE WEST END OF THE AREA #2 PIT STRIPPING SHALE AND LOADING END DUMPS. HE BACKED THE MACHINE UP AWAY FROM THE HIGHWALL TO ALLOW A DOZER TO CLEAN THE BOTTOM. AS HE STARTED TO MOVE UP A SECTION OF THE HIGHWALL FELL IN STRIKING THE CAB AND MACHINE.

EMPLOYEE BECAME AGGRAVATED AT PLASTIC SEAT COVER AND USED HIS POCKET KNIFE TO CUT IT OFF. WHILE DOING SO HE CUT HIS HAND WHICH REQUIRED SUTURES. PLASTIC SEAT COVER WAS INSTALLED 3 YEARS AGO BE CAUSE EMPLOYEE HAD EXCESSIVE BODY ODOR. COMPANY PURCHASED AIR CUSHION TO HELP BUT EMPLOYEE DIDN'T LIKE PLASTIC.

EE IS STATING HE AND ANOTHER EE WERE WORKING TO CHANGE ONE OF THE TRACKS ON A D11 CAT DOZER. INJURED EE WAS STRUCK BY METAL FRAGMENT IN THE CHEST AREA WHEN THE OTHER EE STRUCK THE MASTER LINK WITH A 17# HAMMER. EE WENT TO ER ON 5-2-03, SENTTO A SURGEON PM 5/5 AND HAD METAL PIECE REMOVED ON 5-6-03

EE WAS REMOVING BOLTS WITH WRENCH STRAINED HAND.

EE IS STATING THAT HE WAS PUSHING A WHEELBARROW ON THE CONCRETE FLOOR OF THE PLANT WITH APPROX 10 #S OF LOOSE COAL/MUD IN IT. HE CROUCHED DOWN A LITTLE TO GO UNDER A STRUCTURE AND WHEN HE PROC EEDED HE FELT A SHARP PAIN IN HIS LOWER BACK. THIS CAUSED HIM TO GO TO HIS KNEES AND THEN ON THE FLOOR.

HE WAS GETTING INTO BULK TRUCK & FOOT SLIPPED ON FUEL TANK, HE HIT HIS LEFT KNEE ON FUEL TANK.

EE OVERFILLED A/C GAS TANK, SPILLED GASOLINE RAN DOWN INSIDE ENGINE COVERS. HE SHORTED OUT STARTER TO MAKE ENGINE START THERE WAS A SPARK, IT IGNITED THE GASOLINE, BURNING HIM ON THE ARMS AND FACE.

EE WAS HOLDING A PIN TO BE KNOCKED OUT, WHEN THE MECHANIC HIT HIM IN THE HAND WITH THE HAMMER.

WHILE TRYING TO LIGHT A CUTTING TORCH, THE OXYGEN HOSE BLEW.

EE WAS EMPTYING GOB BIN MUD WAS FLYING & CAME INTO SIDE OF SAFETY GLASSES & IN LEFT EYE

EMPLOYEE WAS OBSERVED SITTING IN THE 988 FRONT- END LOADER NOT MOVING AND UNRESPONSIVE. CPR WAS STARTED IMMEDIATELY AND PROCEEDED UNTIL EMPLOYEEWAS PRONOUNCED DEAD AT THE HOSPITAL AT 15:15 ON MONDAY, NOV. 12, 2001.

EMPLOYEE WAS REELING IN A FUEL HOSE WHEN THE FUEL NOZZLE STRUCK HIM IN THE LEFT LEG CAUSING A LACERATION. THE FIRST DAY HE MISSED WAS 12-17-01.

EE WAS HELPING CHANGE OUT THE SKIRT RUBBER IN THE #8 BELT TAILPIECE. HE WAS USING A PARY BAR TO PULL BELT BACK, WHEN BAR SLIPPED CAUSING HIM TO FELL OFF THE BELT. HE FELL APPROX. FIVE AND ONE HALF FEET TO THE CONCRETE FLOOR.

EMPLOYEE CLIMBED ONTO THE BACK BUMPER OF SERVICE TRUCK. HE SLIPPED AND FELL ONTO THE WASTE OIL BARRELL CUTTING HIS ARM.

WHILE OPERATING A GRINDER, EE WAS WEARING HIS SAFETY GLASSES, WHEN A PIECE OF METAL WENT INTO HIS EYE. (RIGHT EYE)

WHILE OPENING A 988B ENDLOADER FEEDING COAL INTO THE TRUCK HOPPERS, EMPLOYEE EXPERIENCED BACK PAIN.

SECURITY GUARD NOTICED SMOKE COMING OUT OF THE MOUTH OF THE OVERLAND BELT TUNNEL LOCATED AT THE UNDERGROUND OPERATION. COAL WAS SMOKING UNDETR THE FEEDER WHERE COAL HAD PILED UP ON BELT. COAL BURNT THE BELT IN TWO. THIS IS THE ONLY DAMAGE NOTICED DURING THE INVESTIGATION

IN THE PROCESS OF PLACING TOOLS HIS LIFE JACKET GOT HUNG ON SOMETHING, HE TRIED TO UNTANGLE & HIS LEFT ARM GOT CAUGHT

WHILE REMOVING PLANETARY PIN EE STRUCK PIN WITH A HAMMER CUTTING SNAP RING. SNAP RING BORKE HITTING EE IN THE RIGHT SIDE OF HIS CHIN & CHESY

EE WAS STARTING HIS SHIFT, THE CONDITION WAS WET AND RAINY. HE EXITED HIS SUPERVISOR'S VECHILE TO WALK TO HIS WORK TRUCK. WHEN HE SLIPPED ONT HE WET GROUND CAUSING HISFEET TO FLY OUT FROM UNDE R HIM. HE FELL ON HIS BUTT AND LOWER BACK.

EE WAS DRIVING A #338 EUCLID BACK DUMP WHEN HE HIT A BUMP IN HAULAGE ROAD CAUSING HIM TO HIT HIS ELBOW ON BOTL IN WINDOW CRANK.

EE WAS WORKING UNDER A TRUCK WHEN HE WAS HAVING TROUBLE SEEING WHAT HE WAS WORKING ON HE TOOK HIS GLASSES (SAFETY)OFF FOR A MINUTE WHEN SOMETHING WENT INTO HIS RIGHT EYE

EE WAS HOOKING UP THE SCRAP METAL BIN AND AS HE WENT TO LIFT IT WITH THE OVERHEAD CRANE, THE BIN PINCHED HIM BETWEEN ANOTHER TANK.

EE AND ANOTHER EE HAD MOUNTED A 175 LB. TIRE ON THE 763 BOBCAT AND THEN BENT OVER TO PICK UP A LUG NUT, WHEN PAIN STARTED IN LOWER BACK.

EE WAS REPLACING A RETURN ROLLER ON A CONVEYOR BELT IN THE PREP PLANT HE USED HIS BODY TO PUT THE RETURN ROLLER INTO PLACE NEXT DAY HE REPORTEDHIS NECK & SHOULDER WERE SORE BUT DID NOT GO TO THE DR UNTIL 8/7/98 HIS FIRST DAY TO MISS WORK WAS 8/10/98

EE WAS STANDING BESIDE HIS WELDING TRUCK PREPARING TO WELD ON ANOTHER PIECE OF EQUIPMENT WHEN A 50 TON EDN DUMP PASSING BY APPROX. 45 FT AWAY WHEN THE OPERATOR FRONT TIRE BLEW OUT CAUSING A PI ECE OF RUBBER FROM THE BLOW OUT TIRE TO STRIKE HIM ON THE RIGHT SIDE OF FACE AND HEAD.

EE WAS DRIVING AN ARTICULATING END DUMP HAULING REFUSE FROM THE COAL PREP TO THE PIT. ON THE RETURN TRIP HE HIT A POTHOLE IN THE ROAD CAUSING A BACK SPRAIN. HE WAS WEARING HIS SEAT BELT.

EE WAS ATTEMPTING TO REMOVE ONE OF THE HIGH PRESSURE SODIUM LIGHTS FROM A LIGHT PLANT WHEN THE BULB EXPLODED. FLYING GLASS FROM THE BULB CUT EE'S RT ARM AROUND THE WRIST AREA. THIS WOUND REQUI RED SIX STITCHES TO CLOSE. EE'S OTHER ARM WAS CUT IN THE FOREARM AREA AND ALSO REQUIRED SIX STITCHES TO CLOSE.

HAULING REFUSE FROM PREP PLANT.

HOT WATER WENT DOWN BOOT & BURNED FOOT.

EMPLOYEE WAS ATTEMPTING TO CONNECT TEST LEADS TO EACH PHASE FUSE BLOCK. EITHER HIS HAND ORR THE TEST LEAD CLIP CAME IN CONTACT WITH TWO PHASES SIMULTANEOUSLY AND CAUSED A FLASH THAT BURNED HI S FACE, LEFT HAND, AND LEFT FOREARM.

MECHANIC WAS INSTALLING BELLY PAN ON DOZER. HOISTED PAN INTO POSITION AND PUT A NUT ON THE BOLT.WHILE PLACING A SECOND NUT AND BOLT IN THE PAN, THE HOISTING CABLE SLIPPED. THE WEIGHT OF THE PA N STRIPPED THE NUT AND THE PAN FELL PINNING THE VICTIM'S HAND BETWEEN THE PAN AND THE GROUND.

EMPLOYEE WAS PARKED WHILE BEING LOADED. THE BUCKET OF THE LOADING SHOVEL STRUCK THE REAR OF THE TRUCK WENT FORWARD GIVING THE EMPLOYEE A "WHIPLASH" TYPE INJURY.

EE WAS HELPING PULL PUMP HOSE. HOST FOOTING AND FELL BACKWARD TO THE GROUND.

EMPLOYEE WHILE CLIMBING DOWN FROM A 988 LOADER SLIPPED OFF THE SECOND STEP OF THE LADDER AND WHEN HE FELL HE HIT THE LADDER CAUSING LEFT RIB CAGE TO BE BRUISED.