Columbia Plant: 89 citaciones de la MSHA Metal/Non-Metal

He was helping to change the runner on gravel plant on the dredge when the jaws on the pipe wrench broke and hit him on the hand and chest.

They were changing screens on the sand plant. Employee's foot sliped and he caught his leg on a piece of iron and cut it.

Was working on pump on dredge went to put front face plate on. Where it slides to connect got hand caught between the plate and face plate.

He was jacking the track back on the trackhoe with a come-a-long and the chain broke on the come-a-long. The track fell on his left leg hitting him on the leg about the shin area.

EE WAS COMING DOWN A LADDER OFF THE PLANT - WAS ON THE BOTTOM STEP & HIS FOOT SLIPPED ON A ROCK AND HIS KNEE HIT A PIECE OF STEEL ON PLANT.

EMPLOYEE WAS MAKING A HEADACHE BALL FOR THE DRAGLINE. HE PICKED UP THE DRAGLINE TO MOVE IT AND PULLED HIS BACK. HE DID NOT EXPEREICNE A LOT OF PAIN AT FIRST, BUT IT GOT WORSE OVER TIME.

THE EMPLOYEE WAS ACTICING AS THE WATCH PERSON WHILE ANOTHER EMPLOYEE WAS CUTTING AN OLD CONTROL HOUSE FROM A DREDGE. THE INSULATION IN THE TOP OF THE HOUSE CAUGHT FIRE AND FELL ON THE EMPLOYE E.

REMOVING A CHAIN CLAMP FROM A PIPELINE WITH A STILSON WRENCH. CLAMP TURNED SIDEWAYS-EMPLOYEE LET GO AND IT JERKED HIS LEFT ARM.

EMPLOYEE CLIMBING UP ON THE EAGLE SAND SCREW, WHICH WAS NOT OPERATING AT THE TIME TO CHECK FOR ROCKS IN THE MASON SAND. HE BUMPED HIS HEAD ON A STEEL GUARD AND SUSTAINED THREE SMALL SCRATCHES ON THE LEFT SIDE OF THE TOP OF HIS HEAD.

EE WAS REMOVING CHAIN WHICH SECURED A LOAD ON A TRAILER. HE YANKED THE CHAIN THE CHAIN FLEW OFF AND THE HOOK HIT HIS RIGHT FOOT 2 INCH ABOVE THE LITTLE TOE. IT IS BADLY BRUISED AND THE INJURY HAS CAUSED GOUT AND ARTHRISTIS IN HIS ANKLE TO BECOME WORSE.

EMPLOYEE WAS USING A TORCH TO CUT THE ANGLE IRON SUPPORTS THAT HELD A 1/4IN PLATE ATTACHED TO A VIBRATING SCREEN AS HE CUT THE LAST TACK WELD HOLDING THE PLATE THE PLATE SWUNG LOOSE & FELL ON TOP OF HIS LEFT FOOT

EMPLOYEE WAS GOING TO MOVE A PUMP LINER WITH END LOADER. HE WAS RUNNING A CHAIN THROUGH THE LINER WHILE PUMP SUPPLY SALESMAN HELD THE LINER UP. SALESMAN COULD NOT HOLD LINER UP AND IT FELL ON EMPLOYEES FOOT BRUISING.

EMPLOYEE HAND SLIPPED OFF OF WINCH HANDLE UNDER TENSION HANDLE HIT RT WRIST CAUSING IMPACE SPRAIN WINCH WAS MOUNTED ON WORK BARGE WHICH EMPLOYEE WAS ATTEMPTING TO MANEUVER

EMPLOYEE WAS REPOSITIONING DREDGE BY SUING MANUAL WINCH CONNECTED BY LINE TO BANK.HE DID NOT NOTICE THAT WINCH LINE HAD TENSION IN IT.HE TOOK SAFETY CHAIN OFF WINCH BUT DID NOT HOLD HANDLE WHI LE HE DID SO.BECAUSE HE DID NOT HOLD THE HANDLE,IT SPUN AROUND AND HIT HIS ARM.

EMPLOYEE WAS LOADING CRUSHER PARTS INTO LOADER BUCKET. OPERATOR TILTED LOADER BUCKET BACK TO KEEP PARTS IN AND EMPLOYEE FELL TO BUCKET. HE HURRIED BY GOT OUT OF BUCKET TO KEEP PARTS FROM FAL LING ON HIM. WHILE HE WAS GETTING OUT HIS LOWER LEFT LEG GOT WEDGED BETWEEN LOADER TEETH CAUSING THE INJURY.

EMPLOYEE WAS CLIMBING OUT OF TRUCK WHEN HE STOPPED ONTO STEP DOWN HIS FOOT SLIPPED CAUSING L HIMFOR FELL OUT OF TRUCK STRIKING HIS BACK ON SEDDER TANK FUEL OR GREASE ON SHOES PROBABLY CAUSED FOOT TO SLIP SUSTAINED BRUISE TO BACK.

EMPLOYEE ALONG 4ITH HELPER WAS LIFTING PUMP SHAFT OFF OF 6 X 12 TIMBERS SET ON FLOOR EMPLOYEES FOOT STRUCK ONE OF THE TIMBERS CAUSING HIM TO LOSE HIS BALANCE PUMP SHAFT AND OTHER EMPLOYEE FELL ON HIS LEFT LE1 WHEN HE TRIPPED

INSTALLING BELT ON VIBRATOR,SLIPPED AND FELL FROM PLATFORM FELL OVER WING WALL THEN TO GROUND.