Snyder: 1 muerte registrada Metal/Non-Metal

The blaster had just set off a blast and smoke was observed on the south side of the mountain after the dust from the blast had cleared. The Plant Manager checked the smoke, noticed a small fire on the south side of the mountain and notified the local Fire department and MSHA.

Installing control valve, lifting strap broke causing employee to catch hand between machine frame and control valve when it fell.

EE1 was working along EE2 and EE3 on re-torqueing the drive belt on the primary jaw crusher. EE3 was in control of the functions of the portable hydraulic ram. While EE1 was holding the hydraulic ram and spacer in position to tighten the drive belts, the ram and spacer slipped upward pinching EE1's right thumb between the motor and the spacer.

EE was lining up washer and wedges to install adjustment cap and floating hopper on a 5-1/5 cone crusher. The floated hopper separated from the adjustment cap and pinned the left forearm of the EE between the hopper and the bowl. The EE received medical treatment for cleaning of a puncture wound from a cotter pin and was released to full duty. No other injury occurred.

Changing shank on loader. In order to repair, had to remove wear plates that were bolted in. Using impact to remove nuts from bolt, cut palm on bolt. Received 12 stitches in right hand palm.

EE was welding for 15 min when received minor burns to eyes. The auto-darkening filter automatically shut off and the employee forgot to re-energize before EE began welding. EE reported eyes were burning the next day. EE was taken to ER where EE was diagnosed with minor burns to the eyes and released to full duty. EE was given a prescription for eye drops.

EE attempted to reinstall an A/C vent louver. EE placed fingers beside and over the edge of the louver trying to hold the screw so ee could screw the louver back on. The louver abruptly turned resulting in right middle finger and right ring finger to make contact with the squirrel cage fan. EE suffered a laceration and received 5 stitches to the right 3rd finger.

EE working on 992C Loader in shop. EE removed the Shut-Off Solenoid from RR of loader; it dropped to the floor. EE descended loader to pick up the part. EE slightly bent knees & bent over at waist to pick up part when ee felt a pop & pain right knee; ee then fell to the floor holding the knee. EE suffered a Transient Patella Dislocation (small knee cap dislocation).

A power outage was reported by the plant operator. Smoke was visible in NE Corner by east pond on property. It was determined the grass fire was caused by a downed electric line and area was secured; the fire dept and SW Rural Electric (SWRE)were called to the plant. SWRE secured the elec line and Fire Dept began to spray the flames. The fire was extinguished at 9:50 am.

Employee was opening the VSI crusher lid and middle finger got stuck between the hopper and the crusher lid. Employee obtain 10 stitches on the bottom of his middle finger.

Two employees were in the process of making welding repairs to the back of a skid steer loader bucket. The hoist cylinder continued lowering until it free fell forward and downward. When the employee realized the bucket was falling, he moved backward and the attachment ear on the right side of the bucket landed on top of his right foot crushing three toes.

Employee was working on P-3 skirt rubber. Skirt rubber bracket was stuck. He used a silver bar to pry the bracket loose, bracket sprung loose causing silver bar to slip striking him in upper left side of lip.

The investigation into the accident is on-going, but as of now, it appears as the three employees were installing ground vault indicator lights when an ach flash occurred, injuring them. The employees were transported to the hospital.

The investigation into the accident is on-going, but as of now, it appears as the three employees were installing ground vault indicator lights when an ach flash occurred, injuring them. The employees were transported to the hospital.

Employee was adjusting skirt rubber at tail section of conveyor while standing inside the bed of a 1/2 ton pickup. Employee loosened fastener bolts when ratchet came in contact with moving conveyor belt. Employee's finger was smashed between ratchet and conveyor.

Employee performing maintenance/welding repairs to the plant, stepped down from a platform (about 10" drop) and stepped on a rock, twisting his ankle. After first aid he was released with no restrictions. Later taken off work on 9/19/07.

Shift began 4:00 PM on 11/13/06 and ended at 4:00 AM on 11/14/06. Employee was using an aluminum step ladder to gain access to the lower section of the crusher he was working on. As he was decending the ladder he cut his left hand on a sharp edge on the top of the ladder.

Employees had disassembled the VSI crusher. The sheive fell over striking the the employee in the right wrist area, causing a laceration.

WAS ATTEMPTING TO MOVE HYD. CYLINER WHICH WAS TOO HEAVY WHILE IN AWKWARD AND OR IMPROPER POSTION

EE WAS MAKING A DRILL STEEL CONNECTION. THEY HAD MADE THE CONNECTION. EE REACHED DOWN TO PULL THE V WRNECH OFF OF THE STEEL WHEN THE ROTATION KICKED IN TURNING THE STEEL AND WRENCH. EE S FOOT WAS CAUGHT BETWEEN THE WRENCH AND THE WRENCH STOP. HIS STEEL TOLD BOOT PROTECTED HIS FOOT, BUT ALL THE TOES ON HIS RIGHT FOOT ARE VERY BADLY BRUISED.

EE WAS DISASSEMBLING A SPRING STYLE THROUGHING ROLLER WHEN THE ROLLER FRAME HIT HIS LEFT LEG AROUND THE KNEE AREA.

WAS MOVING A BIG ROCK FROM OUT OF WAY OF DUMP AREA. FELT BACK POP. STRAIN BACK - SENT HOME TO REST AND SOAK IN HOT WATER. WENT TO DR. 5/11/99

EMPLOYEE EXPERIENCED PAIN IN LOWER BACK THE FOLLOWING DAY AFTER REPAIR JOB WAS COMPLETED. WO EMPLOYEES REPLACED WEAR SEGIMENTS IN ROCK COLLECTING LEAV. FAX TWO CONVEYORS. THE WEAR SEGMENTS W EIGHS ABOUT 100 LBS. HE DID NOT TAKE OFF UNTIL 11-16-98 FOR PROBLEM.

EE WAS DESCENDING FROM A 30" CONVEYOR VERTICLE TAKE-UP WHEN HE LOST HIS FOOTING AND FELL LANDING ON A 4' PRYBAR THAT WAS IN A VERTICLE POSITION. PUNCTURE WOUND TO THE GROIN AREA. X-RAYS AND SO NOGRAM TEST CONFIRM NO DAMAGE DONE. CLEANED WOUND AND SUTURES SENT HOME SAME DAY.

FOREIGN OBJECT BLEW INTO EYE WHILE CLEARING AN OVERLOADED CONE CRUSHER. EMPLOYEE STARTED HE WAS WEARING HIS SAFETY GLASSES.

THERE WAS ROCKS HUNG IN THE CONVEYOR & INJURED HAD WENT TO TAKE THEM OUT. HE WAS ON HIS WAY BACK DOWN WHEN HE LOST HIS BALANCE & FELL OFF THE CONVEYOR.

I.NAME TIGHTENING 2 BOLTS ON HINGED PIN CAP OF JAW CRUSHER.PIECE OF 3/4" X 5" BAR STICK WHICH HE HAD HANDHOLD ON BROKE AT THE WELD CAUSING FALL 7' TO CONVEYOR TAIL PULLEY GUARD.THEN FELL ANOTH ER 3' TO THE GROUND.I.NAME WASNT WEARING SAFETY BELT....DR SAID...NO BROKEN BONES;SCRATCHES AND BRUISES RIGHT SIDE AND HIP ONLY.

OIL RING BROKE CAUSING FLUID LOSS. ROCK BREAKER FELL OFF I BEAM MOUNT AND SWUNG AROUND KNOCKING MAN DOWN SCRAPING LEFT LEG AND HITTING LEFT SHOULDER.