Camden Plant Metal/Non-Metal

EE CLIMBED METAL STEPS TO ENTER CAB OF FRONT END LOADER. BANGED ANKLE ON STEPS.

EMPLOYEE WAS WORKING ON PYRITE #1 ON 10-29-02 HE WAS PULLING 50 LB BAGS AT THE TIME. HE PICKED UP A BAG AND TURNED TO PUT THE BAG ON A PALLET, AND FELT PAIN IN HIS LOWER BACK.

WAS GOING TO SIT DOWN AT HIS CLOTHES LOCKER. BANGED HIS FOREHEAD ON OPENED LOCK (METAL) DOOR.

LIFTING 100# BAG FROM A PALLET TO PUT IT ON ANOTHER PALLET WHILE BAGGING AT A PACKING UNIT. (EE WAS WEARING A SAFETY SUPPORT BELT.) HE SAID HE FELT A PAIN IN HIS LOWER BACK.

PUTTING PALLET DOWN TO PACKAGE OFF PRODUCT. PALLET CAME DOWN ON LEFT FOOT (TOE).

PACKAGING BAG PACKER DID NOT FULLY SHUT OFF WHEN FILLED BAG WHEN READY TO BE REMOVED. HE SLAMMED OFF BUTTON WITH HAND TO SHUT DOWN INJURING PALM OF HIS HAND.

FIRE OF UNDERTERMINED ORIGIN OCCURRED IN PLANT AIR COMPRESSOR ROOM. ESTIMATED DURATION 1 HOUR. EXTINGUISHED BY COMDEN CITY FIRE DEPARTMENT.

HELPING SHOVEL PRODUCT FROM WALK GRATE AOVE RYING SCPTEN FOR MAINTENAINCE WORK AND CHANGE ONE OF PRODUCTS.

REASSEMBLING A ROLLER MILL FROM REPAIRS. WAS INSTALLING METAL PARTICLE SEPERATOR EQUIPMENT. CAUGHT HAND AND FINGER BETWEEN SEPARATOR EDGE AND WAL OF MILL.

HELPING CLEANUP HYDRAULIC OIL SPILL FROM A DELIVERY (RAW MATERIAL) CARRIER TRUCK. WORKER TRIPPED WHILE RUSHING TO GET CONTAINER AND HAD RIGHT ANKLE INJURY.

EMPLOYEE WAS MAKING A WELDING REPAIR TO A PRODUCT SHUTE ON A CRUSHING UNIT. HE RAISED HIS WELDING SHIELD TO SEE THE WELD HE WAS DOING AND A SMALL PARTICLE OF METAL POPPED INTO HIS FACE LODGIN G IN HIS RIGHT EYE.

EMPLOYEE WAS TIGHTING UP TENSION BOLT OR CRUSHING UNIT. HE WAS OPERATING. THE LARGE 20" WRENCH HE WAS USING, SLIPPED FROM HIS HANDS AND FELL ON HIS LEFT FOOT. (EMPLOYEE WAS WEARING WORKING BOOTS).,

HE HAD DUMP BUCKET ON FORKS OF FORKLIFT HE WAS HOLDING THE MAST AND WENT TO DROP FORKS TO DUMP BUCKET BUT IT WOULD NOT. PULLED AGAIN TO TRY AND DROP FORKS AND BAR DROPPED AND HIS LEFT INDEX FI NGER GOT CAUGHT.

EE WAS RUNNING SUTURSA SCREEN AND WHEN HE WENT TO TURN OFF THE MACHINE A LARGE ROCK ROLLED OFF ONTO HIS FOOT.

I NAME WAS ADJUSTING THE WEIGHT ON THE SAND PACKER WHEN THE WEIGHT CAME OFF & HIT HIS FINGER

WAS TRYING TO PUSH MATERIAL IN MILL FEED HOPPER THAT WAS STOCKING TO SIDE OF HOPPER MATERIAL WET WAS STANDING ON FLAT DECUTWORK LOST BALANCE DROPPED APPROX. 6 FT TO GLOOR BELOW MILL.

EMPLOYEE WAS FABRICATING A METAL COVER FOR A NEW DRYING SYS BEING INSTALLED HE TRIED TO REPOSITION THE COVER FOR ADDITIONAL WORK BY HIMSELF BY HAND HE FELT PAIN IN HIS LOWER RT BACK AREA

EE POSITIONED FORKLIFT TO LOAD A SUPERSACK GOT OFF TRUCK ON WRONG SIDE GOT GLOVE HE WAS WEARING HOOKED ON GEAR SHIFT TRUCK WENT INTO REVERSE GEAR PULLED EE AGAISNT A METAL I BEAM.

WHILE REASSEMBLING MILL FROM MAJOR BREAKDOWN EMPL PLACED HAND IN AREA WHERE PIECE WAS BEING LOWERED INTO PLACE.EMPL TIP OF RIGHT INDEX FINGER WAS CAUGHT.CARELESSNESS OF EMPL WAS CAUSE.

HELPING OPER FREE CRUCHER. LARGE PC OF ORE ROLLED BACK ON FOOT.

GRINDING METAL MILL PARTS WITH HAND GRINDING TOOL.PIECE FLEW UP INTO FACE UNDER EYE PROTECTION HE WAS WEARING.

REMOVING 4" NUT FROM MIL SIDE PIPE WRENCH SLIPED FROM THE NUT CAUSING AN TO LOSE FOOTING AND FALLING TO FLOOR

BAG PACKER WORK3NG WITH JAMMED UP WITH MATERIAL. HE TRIED TO FREE BELT PULLEY BY HAND. HE DID NOT INSURE THAT BAG PACKER WAS OFF WHEN HE DID FREE THEBAG PACKER KICKED IN AND CAUGHT HIS HAND IN THEBELT THAT D9IVES MACHINE MOTOR.

USED POOR JUDGEMENT AS WHERE TO PLACE HANDS WHEN MOVING LIFTING FORKS OF A FORKLIFT

RAW MATERIAL PILE BEING USED TO FEED MILL, HARD SPREAD TO WIDE LEAVING SMALL PIECES 1 TO 2 INCHES NEAR WALKWAY