Clear Fork Underground Mine Coal

Man slipped & fell striking hand on rock. Dislocated middle finger and small laceration.

According to foreman's report, injured stopped conveyer belt, when wooden crib block and rock came off belt, striking right knee.

Injured was pulling 3" waterline when he slipped, causing waterline to hit him in the mouth, resulting in listed injuries.

AT BIRCH 2A PORTAL. EE WAS PULLING CABLE OFF OF REEL OF SHUTTLE CAR TO MAKE REPAIRS WHEN HE FELT PAIN IN HIS LOWER BACK AND LEGS. EE BEGAN MISSING WORK 5/6/05 AND OFFICE WAS NOTIFIED 5/16/05.

THE EMPLOYEE TWISTED HIS LEG GOING THROUGH THE MAIN DOOR & HE EXPERIENCED PAIN IN HIS GROIN. NOTE: INJURY REPORT WAS RECEIVED AT THE OFFICE ON 6/2/05.

Injured was removing a roof jack when a half header (wooden) fell from top of jack, approx. 8-10'high, striking him on the rt. cheek & causing a laceration. The laceration required 6 stitches. Jacks were going to be put into shuttle car to be moved to the next entry.

Injured was stepping off belt tailpiece when foot slipped off of rounded/wet 12"x12" header causing injured to fall and hit back on corner of 12"x12" header. Please note that this accident was not reported until May 2, 2005 because injured did not cease work until 5-2-05, due to injury worsening.

INJURED WAS WALKING ALONG BELT, WHEN A DRAW ROCK (3 1/2 FEET DIAMETER & 4" THICK) FELL STRIKING HIM ON THE SHOULDER ON LEFT SIDE.

Injured was building a permanent stopping when a piece of draw rock fell from mine roof striking injured on right shoulder. Rock was 2' in diameter, and 2" thick.

Injured was tramming scoop down an approximate 7% grade in roadway, and claims to have lost control of scoop and ran scoop bucket into rib, causing an abrupt stop, which in turn caused alleged injuries.

60 feet right of spad 663 #5 entry, draw rock fell between rib and bolts; rock was approximately 1 foot in diameter, and 3/4 inch thick; this rock struck injured in back.

Injured was hooking up chain behind ram on coal hauler when he stepped in hole, twisting knee and ankle, and also received abrasion to front of lower leg (shin).

WHILE SHOVELING MATERIAL & THROWING IT ON STACKER BELT TAILPIECE (CLEAN UP), EE CLAIMS TO HAVE EXPERIENCED SHARP PAIN IN LOWER BACK AREA.

LOADING SUPPLIES (RESIN) ON ROOFBOLTER, TWISTED AND PULLED MUSCLE IN LOWER STOMACH.

INJURED WAS TAKING UP SLACK IN BELT BY USING A GRIP/HAND HOIST WHEN ANOTHER EE ATTEMPTED TO HELP BY "BUMPING" BELT FORWARD WITH DRIVE MOTOR WHICH CAUSED INJURED'S HAND TO SLIP OFF HANDLE ALLOW ING IT TO STRIKE LEFT UPPER LEG. REPORT LOST DUE TO HOLIDAYS - OFFICE WAS CLOSED.

STEPPING OFF OF ROOF BOLTER MACHINE AND TWISTED RIGHT ANKLE #2 ENTRY.

LIFTING SHOVEL FULL OF MATERIAL, HE TURNED TO THROW IT INTO SCOOP BUCKET AND TWISTED LOWER BACK. (WAS NOT REPORTED WITHIN 10 DAYS BECAUSE PAPERWORK WAS LOST IN OFFICE MOVE).

MINER BACKED INTO FREEDOM CAR AND PINNED HIM BETWEEN CAR AND RIB. INJURED RT FOREARM.

UNINTENTIONAL ROOF FALL MEASURING 70'LONG, 20'WIDE, 4' TO 8'HIGH. OCCURRED IN NO.4 ENTRY 3 BREAKS OUTBY SPAD NO.322. NO INJURIES REPORTED. THIS ACCIDENT WAS CALLED INTO OAK HILL OFFICE BY MR. DALE LUSK.

COAL SEAM 10-11 FOOT HIGH - HE WAS WORKING ON LADDER 6' TO 8' HIGH, FELL ON LADDER BROKE LEFT LEG. TAKEN TO SUMMERSVILL HOSP. BY AMBULANCE.

EMPLOYEE WAS LIFTING ON BELT RAIL TO HANG THE BELT CHAIN.

SHUTTLECAR OPERATOR WAS PREPARING TO LOAD TURNEDSEAT AROUND WITH EE FACING AWAY FROM MINER SHUTTLECAR COASTED DOWN THE HILL WHILE TURNED OFF STRIKING MINER.

STANDING ON SCOOP RESETTING TIMBERS, SLIPPED AND FELL OFF.

LIFTING ON 6" X 12' X 10" FAN SHAFT TO ALIGN AND LEVEL. USING SHOULDER TO LIFT AND FELT PAIN IN NECK.

PULLING TORCH DOLLY THRU MUD GOT PAIN IN LWOER STOMACH.

VICTIM WAS WALKING DOWN STAIRS OF DISPATCHER'S OFFICE WHEN HE TRIPPED AND FELL STRIKING HIS KNEE ON THE GROUND.FRACTURE LEFT KNEE CAP.

HE WAS DRILLING A HOLE TO SET THE FIRST BOLT IN A CROSS CUT AND WHEN HE LET THE BOLT MACHINE HEAD DOWN, IT SET DOWN ON HIS FOOT.

WAS LIFTING AND PULLING ON CONT. MINER CABLE TO REMOVE TI OUT OF ROADWAY.

HE WAS STANDING BESIDE THE MINER AND THE MINER OPERATOR SWUNG THE BOOM AROUND AND HIT THE VICTIM ON THE KNEE.

HE HAD A COME-ALONG HOOKED TO THE OUTSIDE BELT AND WAS PULLING UP SLACK IN THE BELT WHILE MAKING A SPLICE HE STARTED TO LET THE COME-ALONG OFF LOST HIS FOOTING SLIPPED AND CAUGHT THUMB IN THE TEETH OF THE COME-ALONG

HE WAS INSTALLING PIN IN SHEAR HUB ON FEEDER AND CUT HIS HAND ON THE PIN.

LOADING CRIB BLOCKS ONTO FLATCAR LOCATED IN MINE YARD.ICE & SNOW ON AND BETWEEN CRIB BLOCKS AND WHEN HE REMOVED BLOCK FROM STACK ANOTHER BLOCK SLID OFF TOP OF STACK AND HIT HIM ON TOP OF LEFT FOOT.

VICTIM WAS LOADING CINDER BLOCK ONTO A FLATCAR LOCATED IN THE MINE YARD. WHEN HE TOOK A BLOCK OFF TOP OF PRE-STACKED BLOCKS, THE UNDERNEATH BLOCK BECAME UNBALANCED AND FELL- HITTING HIM ON TOP OF THE LEFT FOOT.

CLEANING COAL RIB WITH SCOOP.BUCKET HIT AN OFF-SET IN RIB CAUSING SCOOP TO JACKNIFE.HAD HAND OVER BACK OF DECK AND HAND WAS CAUGHT BETWEEN REAR OF SCOOP AND OPERATORS DECK.

CLAIMANT STATED THAT WHILE LIFTING TIMBERS, HE FELT PAIN IN BACK.

THE FALL WAS AP1ROX 20 FT WIDE 20 FT LONG AND 10 TO 12 FT HIGH THE AREA HAD BEEN BOLTED WITH 6 FT RESIN BOLTS AND LOCATED 5 BREAKS OUTBY 4 MAIN SWITCH IN THE TRACK ENTRY THE FALL WILL NOT BV BE CLEANED UP 3

THE BOLT MACHIN9 OPERATOR WAS MOVING BOLTER BACK TO POSITION FOR NEXT ROWN OF BOLTS THE OFF SIDE OPERATOR WAS AT THE REAR OF THE BOLTER AND THE MACHINE RAN OVER HIS FOOT

THE CREW LEFT N2. 8 SECTION IN NO. 7-B MANTRIP AND WHEN THEY STARTED DOWN THE GRADE, THE OPERATOR APPLIED THE BRAKES AND THEY WERE INOPERABLE. AS THE TRIP INCREASED IN SPEED, A DERAILMENT OCCU RRED AND THE TR3P CAME TO A STOP AGAINST THE COAL RIBS.

THE CREW LEFT T2E SECTION IN NO. 7-B MANTRIP AND WHEN THEY STARTED DOWN THE GRADE, THE OPERATOR APPLIED THE BRAKES AND THEY WERE INOPERABLE. AS THE TRIP INCREASED IN SPEED, A DERAILMENT OCCURR ED AND THE TRIP3CAME TO A STOP AGAINST THE COAL RIBS.

THE CREW LEFT N2. 8 SECTION IN NO. 7-B MANTRIP AND WHEN THEY STARTED DOWN THE GRADE, THE OPERATOR APPLIED THE BRAKES AND THEY WERE INOPERABLE. AS THE TRIP INCREASED IN SPEED, A DERAILMENT OCCU RRED AND THE TR3P CAME TO A STOP AGAINST THE COAL RIBS.

THE CREW LEFT T2E SECTION IN NO. 7-B MANTRIP AND WHEN THEY STARTED DOWN THE GRADE, THE OPERATOR APPLIED THE BRAKES AND THEY WERE INOPERABLE. AS THE TRIP INCREASED IN SPEED, A DERAILMENT OCCURR ED AND THE TRIP3CAME TO A STOP AGAINST THE COAL RIBS.

THE CREW LEFT N2. 8 SECTION IN (O. 7-B MANTRIP. WHEN THEY STARTED DOWN THE GRADE, THE OPERATOR APPLIED THE BRAKES AND THEY WERE INOPERABLE. AS THE TRIP INCREASED IN SPEED, A DERAILMENT OCCURRE D AND THE TRIP 7AME TO A STOP AGAINST THE COAL RIBS.

A GRAB HOOK SLI1PED OFF A POIECE OF METAL THAT WAS 4 FT X 10 FT X 3/8 INCH AND THE METAL FELL AND HIT THE MAN ACROSS HIS LEGS.

SHOVELING UNDER BELT AND FELT PAIN IN BACK.NOT REPORTED UNTIL 1-5-88 WHEN HE RETURNED.

HE WAS CARRYING3A COLLAR FOR A FOOT SHAFT FOR A MINER ON HIS SHOULDER AND HE GOT A CATCH IN HIS LOWER BACK.

THE MAN WAS WAL5ING THROUGH A CROSS CUT BETWEEN THE BELT ENTRY AND THE TRACK ENTRY AND HE TURNED HIS ANKLE.

MAN WAS USING H2DRALIC DRILL AND A HOSE BURSTED AND WHEN HE LET GO OF THE DRILL THE HANDLE OF THE DRILL CAUGHT HIS WEDDING RING AND THE RING CUT HIS RING FINGER ON THE LEFT HAND RESULTING IN 6 STITICHES. 3

THE FALL FELL A6OVE ANCHORAGE IT WAS APPROX 55 FT LONG 20 FT WIDE AND 7 FT HIGH THE AREA HAD BEEN BOLTED WITH 6 FT RESIN BOLTS IT DID NOT AFFECT VENTILATION OR PASSAGE OF MEN IT HAPPENED IN TH FACE OF #1 ENT9Y ON #8 SECTION

CLAIMANT CLAIMS3HE HURT HIS BACK WHILE LOADING (LIFTING) FRONT IDLER FOR MINER

THE FALL FELL A6OVE ANCHORAGE IT WAS APPROX 30 FT LONG 20 FT WIDE AND 7 FT HIGH THE AREA HAD BEEN BOLTED WITH 4 FT RESIN BOLTS IT DID NOT EFFECT VENTILATION OR PASSAGE OF MEN IT WAS LOCATED O MMU 065-0 IN TH9 FACE OF #1 ENTRY

WAS MOVING SHUT7LE CAR THROUGH CROSS-CUT & CAUGHT FINGERS OF LEFT HAND BETWEEN TOP OF CANOPY AND MINE ROOF.

WHILE SHOVELING3ON THE BIRCH INCLINE BELT-THE CONVEYOR BELT CAUGHT THE SHOVEL AND PULLED THE SHOVEL INTO THE BELT ALONG WITH HIS HAND. HIS HAND WAS CUGHT BETWEEN THE BELT AND IDLER ROLLER. HE HAD TO PULL HIS3HAND BACK TOWARDS HIM TO FREE IT

THE MINING MACH3NE WAS BACKING OUT OF #4 ROOM AND THE EMPLOYEE WAS HELPING WITH THE MINER CABLE-A PIECE OF ROCK FELL FROM BETWEEN THE BOLTS AND THE RIB AND HIT HIM ON THE HEAD. THE ROCK WAS 36 " LONG -24" WID9 AND FROM 1 TO 6 INCHES THICK.

THE FALL WAS AP1ROX. 4-5' THICK AND 20' X 20. IT WAS IN OLD WORKS 2 BREAKS INBY SPAD NO. 48+83. IT DID NOT AFFECT VENTILATION OR PASSAGE OF MEN. THE AREA HAD BEEN BOLTED WITH 4 FT. CONVENTIONA L BOLTS. 3

I.NAME WAS UNLO5DING 7INX9INX16FT HEADERS OFF TRUCK HE HAD MOVED ONE OVER TO PERMIT HOISTING T ONG TO CATCH IT & REACHED FOR NXT 7X9 WHEN THE 1ST ONE ROLLED BACK CATCHING HIS MIDDLE FINGER O F RIGHT HAND BE7WEEN THE TWO HEADERS

WHILE DRILLING 5 HOLE IN THE ROOF TO SET A BOLT A PIECE OF ROCK FELL AND HIT HIM ON THE MIDDLE FINGER ON THE LEFT HAND.

HE WAS USING A 4ACK TO PUT A JEEP ON THE TRACK-HE HAD THE JEEP JACKED UP & WAS PUTTING BLOCKS UNDER ONE END WHEN THE JEEP FELL & CAUGHT HIS RT.HAND BETWEEN FRAME OF THE JEEP & THE BLOCK

WHILE DISASSEMB5ING 14CM5 RIPPTER JACK IN OUTSIDE SHOP VICTIM WAS LIFTING PISTON ASSY. WHEN STUFFING BOX SLID DOWN PISTON ROD CATCHING RT HAND CAUSING CONTUSION TO RT HAND

HELPING ROLL 150 HP MOTOR FROM TRACK ENTRY TO BL// BELT HEAD IN ADJACENT ENTRY AND INJURED BACK.

HE WAS TIGHTENI3G A FISH PLATE BETWEEN TWO TRACK RAILS AND HAD HIS HAND ON TOP OF THE RAIL-A PIECE OF ROCK FELL FROM THE ROOF AND HIT HIM ON THE BACK OF HIS LEFT HAND RESULTING IN A LACERATIO TION & 3 CRACKE8 BONES ON BACK OF LEFT HAND.

LIFTING A TIRE 7O BE PUT ON SHUTTLE CAR HURT LOWER BACK-LUMBAR STRAIN.

HE WAS FIRE BO8SING THE BELTS AND STEPPED ON A PIECE OF OLD BELT HE SLIPPED AND TWISTED HIS BACK

HANGING HIGH VO5TAGE CABLE ,OVEREXTENDED HIS REACH AND FELT PAIN IN LEFT SIDE.

I NAME WAS SHOV9LING BELT WHEN POST FELL OUT ON OFF SIDE OF BELT AND FELL ACROSS BELT AND STRUCK HIM ON LEFT HIP AND THIGH

LIFTED A 6 FT. 7IMBER- TURNED AROUND TO PUT IT ON THE FORKLIFT AND FELT A PAIN IN LOWER BACK.

SHOVELING BELT AND FELT PAIN IN BACK AND HIS BACK HAD BOTHERED HIM BEFORE.

HE WAS USING A 7OME-A-LONG TO PULL THE BELT TAILPIECE BACK AND THE ROPE ON THE COME-A-LONG BROKE AND THE JERK REACTION INJURED THE MANS BACK.

THE FALL FELL 13CROSSCUT OUTBY SPAD #15 AND 24 IN #5 ENTRY AND ACROSS THE CROSSCUT TO #6 ENTRY. THE FALL WAS ABOUT 70 FT. LONG, 20 FT. WIDE AND 6 FT. HIGH. THE AREA HAD BEEN BOLTED WITH 4 FT. RESIN BOLTS. 3

HE TRIPPED ON B2TTOM ROLLER OF BELT STRUCTURE-FELL & HIT HIS UPPER LIP & NOSE ON THE STGRUCTURE

REACHING UP PUS2ING 6' BOLTS IN HOLE IN THE ROOF.

CLAIMANT STATED3HE SWUNG BOLT ER HEAD OUT TO SET OUTSIDE BOLT & CAUGHT HIS ARM BETWEEN BOLT ER HEAD & COAL RIB

HE WAS ATTEMPTI3G TO REMOVE A WHEEL UNIT FROM A SHUTTLE CAR USING A PRY BAR THE BAR SLIPPED AND HIT HIM IN THE RIB CAGE.

HE WAS LIFTING 2N BELT STRUCTURE AND INJURED LOWER BACK

THE MAN WAS DRI5LING BOLT HOLE IN THE ROOF. HE APPLIED TO MUCH UP THRUST ON THE HEAD AND BENT HIS DRILL STEEL. THE STEEL HIT HIM IN THE BACK OF THE WRIST.

STRUCK RIGHT KNEE ON SIDE OF BOLTER.

HE WAS TRAVELIN1 IN AN OPEN MANTRIP AND AS HE WENT THROUGH A DOOR IN THE TRACK ENTRY, THE DOOR HIT HIM ON THE RIGHT ARM.

HE WAS LIFTING 2N A SPEED REDUCER FOR THE BELT HEAD ON THE INCLINE BELT HE WORKED UNTIL 04 20 87

HE WAS DRIVING 5 BUGGY UP THE ENTRY AND HE HIT A HOLE IN THE ROADWAY.IT THREW HIM AROUND SIDEWAYS AND INJURED HIS BACK AND NECK.

DRILLING HOLE I3 ROOF AND DRILL STEEL FOULED IN HOLE.PULLING STEEL OUT IT CAME DOWN AND CAUGHT FINGER BETWEEN STEEL AND HEAD OF BOLTER.

SHIELD PLATE ON3MINER FELL STRIKING EMPLOYEE ON RT INDEX FINGER.

ROOF FAILURE FE5L ABOVE TERMINATION ZONE OF BOLTS. AREA WAS SUPPORTED W/6' RESIN RODS. FALL WAS APPROX 30'X30'X6'-8' IN #5 SECTION INTAKE 2 X-CUTS OUTBY INTAKE OVERCASTS ACROSS WEDT MAINS TR ACK & B ELT. 3

HE WAS DRILLING3 A HOLE IN ROOF HE PUT TO MUCH UP THRUST ON HIS DRILL STEEL HIS STEEL BENT & HIT HIM ON THE LEFT HAND

ROOF FALL ABOVE3ROOF BOLT ANCHORAGE (TERMINATION) IN ADJUCENT ENTRY PURALLEL TO 2 LEFT OFF 2 WEST BELT 8 X-CUTS OUTBY BELT TAIL. FALL WAS 200'X20'X4'-5 1/2' THICK. AREA WAS BOLTED WITH 4' RESI NS 3

STARTED ROOF DR3LL STEEL INTO ROOF WHEN PIECE OF ROCK APPROX 38"X20"X1"-8" THICK FELL BETWEEN & IN FRONT OF T.R.S. STRIKING RT WRIST.

MAN STEPED ON A3LUMP OF COAL AND TWISTED HIS RIGHT ANKLE RESULTING IN A FRACTURE.

THE FALL HAPPEN9D ON 1ST ROUTE OFF WEST MAINS, IN THE BELT ENTRY- SPAD #11 AND 64. IT WAS APPROX. 50 FEET LONG, 20 FEET WIDE, AND 7 FEET HIGH. THE AREA HAD BEEN BOLTED WITH 4 FEET RESIN BOL TS. 3

HE MASHED HIS F3NGER BETWEEN A PUMP MOTOR ANDTHE FRAME OF A PERSONEL CARRIER.

THE MAN WAS COM3NG OUT OF THE MINE IN A JEEP-THE POLE FLEW OFF THE TROLLEY WIRE AND HE STOOD UP TO PUT THE POLE BACK ON. WHEN HE STOOD UP HE HIT HIS HEAD ON AN OVERCAST.

ROOF FALL ON TR5CK ENTRY AND 2 WEST BELT ENTRY. AREA WAS BOLTED WITH 3 FT CONVENTIONAL BOLTS AND SOME CRIBS AND 4 FT RESIN BOLTS HAD BEEN SET AS SUPLEMENTAL SUPPORT IN THE AREA FALL MEASURED 1 190 FT L X 20 0T W X 3FT THICK.

THE VICTIM STAR7ED HIS DRLL STEEL INTO THE TOP- AS HE STARTED DRILLING HE PUT TO MUCH UP PRESSURE ON THE HEAD AND IT BROKE THE RILL STEEL. IT HIT HIM ON THE LEFT HAND.

EMPLOYEES GLOVE3GOT CAUGHT WHILE HOLDING ON DRILL STEEL ON ROOF BOLTER

WAS STANDING ON3OIL CAN WHILE HANGING CURTAIN. FELL OFF CAN & DISLOCATED RIGHT ELBOW.

WAS WALKING CAR9YING CAN OF OIL. HIT HIS HEAD AGAINST ROP HURTING NECK.

AREA WAS ROOF B2LTED W/ 6' RESIN RODS. FELL ABOVE BOLTS. FALL MEASURED 60'L X 20'W X 7' THICK IN RETURN AIRWAY OF #3 & #5 SECTIONS. DID NOT AFFECT VENTILATION OR PASSAGE OF MEN. WEST MINES #2 ENTRY 1 X-CUT O6T BY SPAD #20+64.

A PIECE OF ROCK36 L X 2 1/2 X 2 THICK FELL FROM BETWEEN BOLTS AND STRUCK I NAME ON THE HEAD AND FACE.

HE WAS USING BA9 TO PRY FEEDER CONVEYOR CHAIN WHEN PRY BAR SLIPPED CAUSING PAIN IN ADBOMEN.

VICTIM WAS HOLD3NG BAR ON PIN & CO-WORKER WAS HITTING BAR WITH SLEDGE HAMMER TO KNOCK PIN OUT OF MINER.BOOMWHEN HE STRUCK VICTIM ON LEFT WRIST WITH HAMMER.

THE FALL WAS I 3 THE BELT ENTRY ABOUT 1000 FT INBY THE PORTAL FALL IS APPROX. 20 LONG 10 FT WIDE AND 7 FT HIGH AREA HAD BEEN BOLTED WITH 6 FT BOLTS.

HE WAS SCALING 7OP & PIECE OF ROCK STRUCK HIM ON LOWER BACK.

TROLLEY POLE CA6LE ON JEEP ARCHED & HE ATTEMPTED TO REMOVE POLE FROM TROLLEY WIRE & FELL OUT OF JEEP INJURING RT ANKLE SEVERE SPRAIN.

ROOF FALL IN TR5CK ENTRY 2 X-CUTS INBY #7 UNIT BELT DRIVE. FALL IS 20' WIDE X 50' LONG X 16'-8' THICK AREA BOLTED WITH 4' & 6' RESIN RODS.

HE WAS WORKING 2N SHUTTLE CAR CHAIN (PUTTING NEW ONE ON) WHEN PIECE OF ROCK FELL BETWEEN ROOF BOLTS (AREA FULLY BOLTED) STRIKING CRIST ON RIGHT LEG, ANKLE & FOOT.

WORKING ON MINE3TRACK USING RAIL BENDER INJURED HIS BACK.PARTIALLY RUPTURED DISC.

ROOF FALL ON 1 8ECTION IN 5 RM FACE AT INTERSECTION OF TOP X CUT 20FT W X 35 FT L X 4 FT T. AREA WAS BOLTED WITH 4 FT RESIN RODS DID NOT AFFECT VENTILATION OR PASSAGE OF MINERS WILL NOT BE C LEANED UP AREA 1OST OFF.

THE MAN WAS HAN1ING A MINER CABLE AND THE CABLE HANGER PULLED LOOSE CAUSING MINER CABLE TO FALL BENDING HIS LEFT THUMB BACKWARDS RESULTING IN FRACTURED THUMB.

THE FALL WAS LO7ATED IN THE TRACK ENTRY ACROSS FROM #6 SECTION BELT HEAD IT WAS APPROX 20 FT LONG 20 FT WIDE AND 8 FT HIGH THE AREA HAS BEEN BOLTED WITH 6 FT RESIN BOLTS

THE VICTIM WAS 5OADING COAL OUT OF THE FACE WITH A LOADING MACHINE-THE LOADING ARM OF THE LOADER HIT SOLID COAL WHICH THREW THE MACHINE SIDE WAYS. THE VICTIM HAD HIS HEAD OUT FROM UNDERNEATH T HE CANOPY AND W2EN THE LOADER SWUNG AROUND IT CAUGHT HIS HEAD BETWEEN THE CANOPY AND THE COAL RIB.

THE FALL WAS ON3# 7 SECTION IN #6 ENTRY. IT WAS APPROX. 18 FEET WIDE 40 FEET LONG AND 4 FEET TO 12 FEET THICK. THE FALL AREA HAD BEEN BOLTED WITH 6 FEET RESIN BOLTS.

VICTIM WAS LIFT3NG A GATHERING HEAD CLUTCH FOR A MARIETTA MINER WHICH WEIGHT ABOUT 50 LBS. HE PICKED UP THE CLUTCH IN A BENT OVER POSITION, TWISTED AROUND AND HURT HIS LOWER BACK.

THE FALL WAS IN3#1 ENTRY ON #6 SECTION SPAD #4+20 IT WAS 20' LONG 20' WIDE 7' HIGH IT FELL ABOVE BOLT ANCHORAGE THE AREA HAD BEEN BOLTED WITH 6' RESIN BOLTS. IT DID NOT AFFECT VENTILATION OTR OR PASSAGE OF 4EN.

THE EE WAS SETT3NG A TAILPIECE USING A SCOOP TO SET THE TAILPIECE IN PLACE. THE CHAIN BROKE ALLOWING THE TAILPIECE TO MOVE THUS CATCHING VICTIM RESULTING IN THE BOTTOM OF BOTH LEGS & HIS UP PER JAW. 3

VICTIM WAS WORKING ON ROOFBOLTING MACHINE INSTALLING BOLTS WHEN PIECE OF ROCK FELL FORM ROOF STRIKING R LEG

FALL OF ROOF ON 2 LT OFF 2 EST BELT 2 X-CUTS 160FT OUTBY #5 SECTION BELT HEAD FELL IN INTERSECTION 20 FT W X 20 FT LONG X 6FT - 7 FT THICK AREA WAS BOLTED WITH 4 FT RESIN BOLTS

THE FALL WAS ABOUT 20\ LONG 20\ WIDE & 5\ THICK. IT WAS IN THE TRACK ENTRY 3 X-CUTS OUTBY 3 MAIN SWITCH. IT HAD BEEN BOLTED WITH 4\ CONVENTIONAL BOLTS & FELL ABOVE BOLT ANCHORAGE.

THE FALL WAS ABOUT 120 FT LONG 20 FT WIDE AND 5 1/2 FT HIGH IT WAS IN THE INTAKE AIRWAY #6 ENTRYY SPAD #7 & 23 OFF #6 SECTION THE FALL FELL ABOVE BOLT ANCHORAGE IT HAD BEEN BOLTED WITH 4 FT RE SIN BOLTS DID NOT AFFECT VENTILATION OR PASSAGE OF MEN

THE FALL WAS ABOUT 20 FT X 25FT AND 5 1/2 FT HIGH IT WAS IN THE RETURN AIRWAY #1 ENTRY SPAD #8& 48 OFF #6 SECTION THE A REA HAD BEEN BOLTED WITH 4 FT RESIN BOLTS IT DID NOT AFFECT VENTILATIO N OR PASSAGE OF MEN

THE FALL WAS ABOUT 30 FT WIDE AND 6 FT THIGH IT WAS IN AN INTERSECTION IN THE TRACK ENTRY 6 B REAKS OUTBY 1 MAIN SWITCH, THE AREA HAD BEEN BOLTED WITH 4 FT CONVENTIONAL BOLTS REBOLTED WITH 4 FT RESIN.

I NAME STATED THAT HE WAS TRAMMING BOLTER AND WAS LOOKING TO MAKE SURE HE DID NOT RUN OVER BOLTER CABLE HE INADVERTENLY POSITIONED HIMSELF IN SUCH MANNER THAT HIS PELVIS REGION WAS CAUGHT BETW EEN COAL RIB AND CANOPY LEG IN 2 SQUECTING ACTION.AS HE WAS MANUVERING BOLTER THROUGH INTERSECTION IN #5 ENTRY.

FALL WAS 30FTX30FT WIDE & 5 TO 6FT HIGH IT WAS IN RETURN ENTRY 6 BREAKS OUTBY FACE AT SPAD NO 8+94 IT DID NOT AFFECT VENTILATION OR PASSAGE OF MENS IT FELL ABOVE BOLT ANCHORAGE

THE ROOF FALL FELL ABOVE BOLT ANCHORAGE. IT WAS ABOUT 50\ LONG - 20\ WIDE AND FROM 3\ TO 5\ THICK. IT WAS IN OLD WORKS AND DID NOT AFFECT VENTILATION OR PASSAGE OF MEN. THE FRALL WAS LOCATED A T OLD #3 SWITCH, SIDE TRACK. THE AREA WAS BOLTED WITH 36" CONVENTIONAL BOLTS.

HE HAD GOTTEN OUT OF MANTRIP STOOD UP AND SLIPPED AND FELL AGAINST SIDE OF MANTRIP BUS.

THE MAN WAS KNOCKING DICK PINS OUT OF FEEDER CHAIN WITH A HAMMER WHEN HE MISSED THE PIN AND HIT HIS LEFT THUMB

PART OF CUTTER HEAD-TUB- SUSPENDED WITH HOIST. HOOK SLIPPED LETTING TUB FALL STRIKING TOES ON RT FOOT.

WAS EXTENDING SECTION BELT & BELT SLIPPED OFF STRUCTURE STRIKING HIS RIGHT KNEE FROM BEHING

EMPLOYEE WAS USING PRY BAR TO LIFT CUTTING HEAD MOTOR FROM SUPPLY CAR WHEN PRY BAR SLIPPED STRIKING EMPLOYEE BEHIND RIGHT EAR CAUSING LACERATION

WHILE ROOFBOLTING IN #6 FACE OF #6 SECTION A PIECE OF BOLT STEEL FLEW & HIT VICTIM IN FACE CAUSING FACIAL FRACTURE ABOVE THE EYE & FRACTURE OF NOSE. ALSO CAUSING LACERATION AROUND RT EYE.

WHILE ROOFBOLTING IN #4 ROOM FACE ON #2 SECTION A PIECE OF ROCK FELL FROM TOP CAUSING LACERATION TO LEFT EAR.

WAS TRAMMING CUTTING MACHINE FROM #5 ENTRY TO #4 ENTRY AND BACKED INTO A POST INJURING RT HIP AND LOWER BACK

THE FALL FELL AT BOLT ANCHORAGE, IT WAS 6 FEET HIGH - 40 FEET LONG AND 30 FEET WIDE. THE FALL WAS IN THE BELT ENTRY TOWARDS #3 SECTION - 1 BREAK OUTBY SPAD 45 + 74.

PRYING ON APRON UNDER MINER BOOM AND APRON BROKE LOOSE CAUSING PRY BAR TO SPRING UP AND HIT HIM ON LEFT JAW.

SHOVELING ON BELT AND TWISTED BACK

THE FALLWAS ABOUT 4\ HIGH 20\WIDE AND 35\LONG.WE WERE USING 4\ RESIN BOLTS AND IT FELL AT BOLT ANCORAGE. THE FALL WAS ON #6 SECTION 1 BREAK INBYSPAD NO 10&31.

THE FALL WAS ABOUT 50 LONG 20 WIDE AND 4 THICK IT FELL RIGHT AT BOLT ANCORAGE IT IS LOCATED 3 BREAKS INBY SPAD 23 AND 4I IN 1 ENTRY IN SILO MIN MAINS.

FALL IN OLD WORKS IN MMU 052-0 RETURN AIRWAY-NO AIRWAY BLOCKAGE-THE FALL WAS ABOUT 20 FT. WIDE-45 FT LONG AND 0 IN TO 4 FT HIGH. THE AREA HAD BEEN BOLTED WITH 3 FT CONVENTIONAL BOLTS. LOCATE D AT SPAD NO.3 + 58.

THE FALL WAS ABOUT 20\W X 20\L AND FROM 0 TO 3\ THICK - IT FELL AT BOLT ANCHORAGE

FRACTURED BOTH FEET - HE WAS PREPARING TO WELD A 1/2" X 2\ X 8\ PIECE OF METAL ON A TAIL PIECE WHEN THE PLATE OVER BALANCED ON ROLLERS AND FELL EDGE WISE - STRIKING TOP OF BOTH FEET

THE MAN WAS PULLING DOWN A PIECE OF ROCK AND THE ROCK FELL ON HIS BIG TOE.

FALL IN FACE OF BELT ENTRY OF NEW SECTION SET-UP 20\X12\X5\ THICK. AREA WAS BOLTED WITH 4\ RESIN BOLTS NO ACTIVE MINING BEING DONE. NO INJURIES.

HE STEPPED ON A ROCK & TWISTED HIS RIGHT KNEE

OUTSIDE HIGHWALL SLIPPED AND FELL AT #3 SECTION INTAKE AIRWAY.

CLEANING BELT WHEN SHOVEL GOT CAUGHT BETWEEN TOP BELT AND IDLER ROLLER PULLING RT ARM OVER TOP IDLER ROLLER

WORKING ON BELT ROPE AND CUT LITTLE FINGER ON LEFT HAND

CLAIMANT STATED HE WAS WORKING ON BELT HEAD CHAIN GUARD AND SPRAINED HIS BACK

STRAINED BACK WHILE LOADING SUPPLIES (ROOF BOLTS) IN SCOOP.

HE HURT HIS BACK WHILE HANDLING OXYGEN TANKS.

ROOF FALL IN #5 ENTRY #3 SECTION (049-0) 128\LX20\WX5\ THICK STARTING 30\ INBY SPAD #22+63 PLACE WAS BOLTED WITH 4\ RESIN BOLTS.

LIFTING 7"X9" HEADERS FROM FLAT CAR & CAUGHT LEFT FOREFINGER BETWEEN HEADERS-DRACTURED FINGER.

THE FALL FELL ABOVE ROOF BOLTS 4FT TO 5FT HIGH 16FT LONG AND 20FT WIDE THE FALL OCCURED ON 3 SECTION IN THE 4 ENTRY THE TOE OF THE FALL IS ABOUT 50IN INBY SPAD NO 40+93

FALL ABOVE ROOF BOLTS 4 TO 6 FEET HIGH- 20 FT WIDE-AND ABOUT 35 FT LONG, ON #3 SECTION IN #6 ENTRY-2 BREAKS OUTBY FACE.

FALL ABOVE ROOF BOLTS 1 CROSS CUT INBY SPAD # 30 92 IN THE BLET ENTRY THE FALL WAS 30X35X7

INJURED LEFT ARM WHILE HANGING MINER CABLE ON SECTION

THE ROOF BOLT WRENCH FLEW OUT OF CHUCK AND HIT HIM ON FOREHEAD.

MAN WAS BUILDING A CRIB AND A PIECE OF ROCK FELL FROM TOP HITTING MAN ON LEFT ARM ABOVE AND BELOW ELBOW HAIRLINE FRACTURE ON FOREARM

WATER ENTERED FROM OLD WORKS CAME DOWN SOUTH EAST MAINS AND COVERED THE TRACK FOR A DISTANCE OF ABOUT 1200FT ON THE SUMMERSVILLE MAINS ALSO WENT ON 2 MINER SECTION

SLIPPED ON STEPS OF SUPPLY HOUSE WHILE CARRYING BOX OF BATTERIES AND FELL STRIKING LEFT HIP ON STEPS AND BOX OF BATTERIES FELL ON LOWER ABDOMENT/.