CLEBURNE S & G #282 A&B: 1 muerte registrada Metal/Non-Metal

HAD INSTALLED A NEW ROLLER ON CAT D9R WHEN ONE BOLT BROKE.LOOSENED INSIDE BOLTS SLIGHTLY TO ALLOW ROLLER TO TILT DOWN & OUT OF THE WAY TO REMOVEDUTCHMAN. WHEN REMOVING THE LAST OUTER BOLT THE ROLLER FELL MORE THAN EXPECTED CATCHING THE MIDDLE FINGER ON LEFT HAND. THE ROLLER WEIGHS 250 LBS. WAS USING A 3/4" IMPACT TO LOOSEN BOTTOM ROLLER

EMPLOYEE WAS UNHOOKING FUEL TRAILER FROM PIU, WHEN HE FELT PAIN IN HIS RIGHT HIP. WENT TO SEE DOCTOR. DOCTOR RELEASED HIM TO LIGHT DUTY UNTIL 11-28-01.

WORKING IN CLOSE QUARTERS WITH HEAVY ITEMS. BEARING & BEARING HOUSING WAS PUSHED ACROSS FLOOR WITH COMEALONG. RAISED & THEN TURNED AND LASHED INTO PLACE.

EE WAS AT THE SCALE HOUSE. A TRUCK WAS COMING UPTO THE WINDOW TOO CLOSE TO HIM SO HE MOVED TO GET OUT OF THE WAY. HE TRIPPED & FELL ON METAL BARRAILING ON CHEST & CHIN.

CLEANING AROUND CRUSHER WITH PRYBAR AND HAMMER. LEFT ARM FROM ELBOW TO MUD SHOULDER BLADE EXPERIENCING PAIN.

EE WAS REPAIRING DRAGLINE. DUG THREE FOOT HOLE, WHILE CLIMBING INTO HOLE, HE SLIPPED AND TWISTED LEFT KNEE.

EE SLIPPED AND HIT HIS LEFT SHIN AND CUT IT WHILE WASHING SAND OUT OF SCREW. EE WENT TO HOSPITAL AND HAD SEVEN STITCHES TO CLOSE THE CUT AND WAS SENT HOME.

CARRYING SCREEN UP STAIRS TO 8 BY 20 PRIMARY SCREEN, TRIPPED ON STEP, STRAINING RIGHT KNEE.

EE WAS CLEANING PLANT AREA WITH BOBCAT, WHEN HE RAN OVER A LARGE ROCK, THE BOBCAT WAS OFF BALANCE AND AS THE WHEELS OF THE BOBCAT TRAVELED OVER ROCK IT CAUSED EE'S HEAD TO JERK FROM SIDE TO SI DE.

EMPLOYEE WAS ALIGNING BOLT HOLES ON MAIN SHAFT COUPLING, HE INSERTED LEFT LITTLE FINGER INTO BOLT HOLES TO CHECK ALIGNMENT OF COUPLING, CUTTINGHIS FINGER. HAD CUT CLEANED AND STITCHED UP AT C LINIC. RETURNED TO WORK AT FULL DUTY 8-23-99.

STUNG BY BEE ON RIGHT FINGER, WHILE OPERATING B-30 EUCLID. DID NOT MISS ANY WORK.

PUSHING ON TIRE WITH RIGHT LEG TRYING TO TURN IT. PULLED MUSCLE IN LEG.

EE SLIPPED AND FELL FROM B-70 EUC TO THE GROUND INJURING RIGHT ARM. DAMAGE WAS HE BRUISED RIGHT ARM.

WHILE WORKING ON ROCK SHAKER, THE CHUTE WAS PULLED AWAY FROM SCREEN FOR MAINTENANCE, CAUSING PAIN TO LEFT KNEE & SHIN AND LEFT ELBOW.

WHILE REPLACING A BUCKET TOOTH PIN, USING A HAMMER A PIECE OF METAL CHIP OFF AND HIT CHIN CUTTING IT. EE WAS TAKEN TO DOCTOR TO REMOVE PIECE OF METAL IN CHIN. RELEASE TO FULL DUTY THE NEXT DAY

WELDING OVERHEAD ON DUMP HOPPER AND WELDING SLAGGOT INTO RIGHT EYE.

DR STATED INJURY COULD HAVE BEEN FROM LIFTING OR STRAINING ON A OTEET.

MOVING OFFICE FURNITURE. CAUGHT FALLING FILING CABINET.

WERE REMOVING DECK FROM SHAKER. HAD PULLED DECK TO TOP OF SHAKER. ATTEMPTED TO RETIE CRANE TO PANEL WHEN PANEL SLIPPED BACK CATCHING LEG BETWEEN PANEL AND A PIPE.

EE WAS INSTALLING A NEW TOOTH ON THE DRAGLINE BUCKET THE TOOTH WAS GOING ON HIGH WHEN EE HIT THE TOOTH WITH A SLEDGEHAMMER AFTER ABOUT 15 HITS WITH THE SLEDGEHAMMER A PIECE CHIPPED OF & WENT I NTO EE LEFT BICEP

BOTTOM OF SHOES GOT WET & SLIPPED OUT FROM UNDER EMPLOYEE ON STEPS.

DROPPED METAL OFF SAW HORSE & FELL ON FOOT.

EMPLOYEE WAS INSTALLING A DUMP CABLE ON THE B30 EUCLID THE CA BLE SLIPPED STRIKING THE HARD HAT THROUGH FOREHEAD OF EMPLOYEE CAUSING A MINER ABRASION TO FOREHEAD

CONTINUOUS BOUNCING INSIDE OF EQUIPMENT OVER A PERIOD OF TIME.

DRIVE PARKED HAUL UNIT ON GRADE AND TRAILER BRAKES AND LEFT MACHINE. MACHINE STARTED ROLLING DRIVER TRIED TO CATCH THE TRUCK COULD NOT AND TIRE ROLLED OVER TWO OF HIS RT FOOT. K BRAKE WAS NOT SET.