CLINTON POINT QUARRY & MILL Metal/Non-Metal

while in the process of putting the load on F-Belt employee 101439 went to put a screen in on a 57's feeder when EE felt a pop followed by a warming sensation in the joint of EE's left thumb

While clearing a rock jam in the crusher, the associate lost EE's footing, fell backward, and struck the side wall. EE then slid down to the entrance door of the crusher. After being assisted to EE's feet, EE walked approximately 40 feet and then rested on a walkway. EE expressed concerns about tingling in EE's feet and legs.

Employee 101408 was reaching down to pick up the cable for the north dock winch when they felt some discomfort in their lower back.

Miner was using a shovel to remove material from the tunnel at SP6. While removing material the miner's shovel slipped from miner's grip and went to push forward and had left thumb extend back.

A miner leaving the bull gang area noticed another miner on the ground. Miner on the ground was sitting upright and was coherent. Ambulance service arrived on site to assess the fallen miner. Miner had passed out and fell down. Miner was diagnosed with a broken Right Ankle.

Employee was welding inside a crusher. When employee stepped out of the crusher their left knee gave out. Ice was immediately applied to the left knee and employee requested medical treatment where they were signed out of work. No specific injury has been identified as of yet.

Employee needed knee surgery after 25+ years of maintenance work. Surgery was originally suggested at the end of 2022 when the employee had pain and swelling that didn't go away within a few days but the employee wanted to put it off as long as possible while trying other treatment options. After exhausting other options, surgery was scheduled for 1/2/2024.

Employee notified management of discomfort in their back on 9/12 alleging that on 9/8 EE's back started bothering EE but was common due to previous injuries at past job. EE went to the ER and was signed out of work starting on 9/15 due to lower back pain.

Employee felt a strain in right shoulder/elbow when picking up a piece of steel. Initial incident date 3/9/23 but employee did not want further attention at first. When the pain didn't go away they saw a doctor where they were prescribed a muscle relaxer.

While welding, employee stopped and lifted EE's helmet and itched EE's eye with EE's glove which must have had something on it. We flushed EE's eye with eye wash solution but after awhile EE said that it felt like there was something scratching EE' eye and ask to have it checked out. A small piece of metal was removed with a cotton swab but EE was given a precautionary antibiotic.

Employee was changing out a screen in the Dock Washroom when the screen snagged the employee's glove and pulled the employee's arm with it, tweaking the employee's right shoulder. When it didn't get better the employee saw a doctor three days later where employee was written out of work. X-rays were taken but nothing was identified.

Employee twisted EE's ankle while exiting the break/change room building.

The employee was using a 3 lb. lump hammer to hammer a steel wedge between steel plating and the 450 excavator bucket frame, when EE noticed a small laceration on EE's right index finger. The laceration had a small steel splinter in it that needed to be surgically removed.

Original incident - employee tripped over skid steer bucket and hurt their shoulder on 11/15/2021. No restrictions after this point until employee saw doctor 10/26/2022 where they were scheduled for surgery on 3/17/2023.

While grinding a bearing employee states something got past face shield. Eye was rinsed and they returned to work. Incident was reported 5/18 due to irritation. Employee saw a doctor on 5/24 where no foreign body was noticed but eye drops were given. Management notified 5/28 and this form was submitted the next working day 6/1.

While operating a 70 ton Terex haul truck the operator hit a divot bump at 10mph causing pain in lower back.

The employee was pulling a torch cart when EE slipped and fell. The torch cart handle landed on the back of EE's legs/knees. Knee swelled up but no damage was seen on x rays.

Employee was inspecting pipe. The pipe broke and water from the pipe hit the employee causing the employee to fall. The employee felt discomfort in the left knee.

Employee received a small laceration to thumb while cutting an avocado with a knife during a morning break. Employee received stitches at a local ER.

While moving material in a haul truck employee drove over a bump in the haul road and experienced pain in tail bone/lower back.

while employee was being loaded in truck, claims experienced lower back discomfort, however, injury leading to lost time was applying direct frozen bottle of water to skin causing frostbite

While clearing plug in #4 screen of the 1-1/2" section, associate cut right pinky finger.

While operating portable plant employee pinched finger on grizzly bar leading to a minor fracture and 6 stitches on right index finger. Contributing factor was not following the standard operating procedures set (task training).

While unloading material from a low flatbed, employee was standing on low flat bed of truck, material shifted, employee fell off landing on ground. Fractured pelvis and hip, contusion throughout body from fall

Haul truck driver felt discomfort in neck and lower back after being loaded. It is believed a large stone was in bucket and when loaded into bed it made bed shift side to side.

Employee was using heat to warm slow moving feeder belt and left jacket cuff caught in pinch point of troughing roller and belt and resulted in a left wrist fracture

Replacing old drill pipe from drill rig, rigging on pipe became slack when one end of pipe rested on ground and other end pipe released and fell from strap striking employee on hardhat.

It is unknown at this time but cause of death appears to be a heart related. Employee was operating a Cat 777F haul truck and struck berm and truck came to rest on berm approx 400 feet from initial contact.

Employee standing on lowboy trailer working remote control for overhead crane to adjust 7 foot mainframe crusher on trailer and stepped back into opening in center and dropped 2 feet striking lower back/tailbone on trailer cross member resulting in bruising, no fracture. Prescription meds required and restricted work.

Two employees carrying a 4'x 8' 60 lb plastic liner sheet on second floor of sand plant tower and strong wind gust required them to control the sheet and the action caused a left bicep tendon tear in one employee. Recordable was not known until MRI result on 11/10/14. Employee will not be a lost time.

Employee was rotating a centrifuge drum to wash with hose and felt strain in bicep on 10/17/14. Did not notify supervisor until 10/20/14 and continued to work until MRI revealed a bicep tear on 10/27/14. Employee runs control room and will not be losing time from work.

Employee went to climb up the fixed ladder on the Cat 992 Front End Loader and felt pain in his left shoulder. MRI result on 10/27/14 revealed a rotator cuff tear. Employee will not lose time from work even with current restrictions. Employee is a plant leadman.

Employee was operating dozer in reverse and turning upper body to see behind and dozer lunched after cresting a mound causing a twisting to lower back.

Employee walked up stairs and unknown reason tripped at top of landing and fell striking return idler guard causing laceration to lower arm

Employee standing on one end of stone barge tied to the dock where loading takes place was struck by the winch cable that moves the barge when the cable clamps were unable to hold cable at the cable eye. Employee sustained a simple fracture of the fibula and swelling of area due to trauma requiring a procedure to relieve pressure.

Employee attempting to cut small hole in new belt to pull from and cut inside knee required 3 stitches

Employee was attempting to remove a hatch from a barge with a prybar and prybar slipped, causing employee to receive a laceration to right pointer finger.

Employee turning conveyor drive belts by hand on spare conveyor is storage yard and finger tip pinched bewteen sheave and drive belt

EE was working in the shop and stepped on a 1.5" nut on the floor and strained his right ankle. EE continued to work normal duties but the pain persisted. Intially the doctor thought it was a non-work related bone spur, however in May x-rays showed a stress (minor) fracture. EE continues performing normal functions, no lost work days.

Employee states while operating water truck he struck a rut/pot hole in roadway causing him to be jarred in the seat. Employee was returned to work and placed out of work by his personal physician on 12/8/09.

Working on the pan feeder, the employee tried to position a lever hoist inside the framework of the feeder. After attaching the hook to the framework, he released the body of the lever hoist causing it to rotate downward, pinching his finger between the hoist and link to be installed.

Employee was removing an expanded metal guard on the head pulley for the stacker conveyor to the crusher. The guard slipped off the last remaining bolt and caused a tear in EE's shirt and an abrasion to his right pectoral muscle. He received a tetnus shot from local clinic.

Employee was closing the door of a 100 ton haul truck, when he pinched his finger between the door and frame.

Employee was holding a carriage bolt from spinning with the head of a hammer. Another employee engaged a 1" impact gun and the bolt spun causing the hammer head to slip and the employee's finger was struck by the bolt.

Employee was cutting rubber belting with a knife for use in the 1 1/2" section of the mill, when the knife slippled and struck him in the leg.

Employee was trimming a sticking drawer on his desk with a pocket knife when the blade folded up and cut into his thumb.

Employee was climbing down from 100 ton haul truck when his hand slipped from handrail resulting in employee falling to the ground.

Employee was lifting a wire cable off of a loaded scow when he felt a pull in his shoulder. Employee was seen by doctor and returned to work in modified duty capacity. He continued to have pain and went for further testing which showed slight tear in the shoulder. Doctor has placed him out of work until further evaluation and treatment.

Carrying a part from the storeroom to dumpster the employee was walking on uneven ground a felt a strain in his knee.

Employee lost his footing on wet steps of ladder and broke his fall by grabbing on a railing. He continued to have some pain in arm and had arthroscopic surgery on 1 23/2009.

Employee went to pick up a piece of steel, lost his grip, he tried to catch the steel and it struck his finger against a rock.

Using a knife to cut a box, employee struck his finger.

When crawling backwards after installing part in feeder, employee felt a strain in his back.

While walking through the plant yard the employee slipped in mud causing him to fall. Originally diagnosed with hip strain, an MRI performed in mid-April showed some bone fragmentation, which was removed laparoscopically on 5/15/2007.

Employee slipped on a rock, felt slight pull in abdomen while carrying a case of powder.

Cleaning rock jam with an excavator, employee was dumping a bucket of stone, when a large stone fell and struck stairway. The rock then shattered and a piece of stone struck the windshield of the excavator and then struck the employee's hand.

While exiting bullgang, employee cut finger on doorknob.

While working with another employee replacing a belly pan on the primary crusher, the employee's glove was caught between the nut and the torque wrench.

Employee was shoveling stone around belt when he lost his footing and struck his elbow on the idler

Employee was attempting to catch a barge by the running line when the running line snapped striking the employee in the left upper chest area causing a dislocation of his shoulder.

Employee dropped a lit torch causing burns to his lower leg.

EMPLOYEE JUMPED FROM BOAT TO DOCK AND FELT PAIN IN HIS KNEE.

EE WAS DOING REPAIR WORK ON 21K, WHILE SWINGING A SLEDGE HAMMER HE HIT HIS L INDEX FINGER.

EMPLOYEE SLIPPED ON SNOW-COVERED ICE.

EE WAS HAMMERING A PIN ON A CHAIN OF A 992 LOADER, THE PIN SLIPPED OFF THE CHAIN CAUSING THE EE TO HAMMER HIS FINGER.

EMPLOYEE WAS PUTTING ANTIFREEZE IN AIR SYSTEM ON CATWALK. HE TRIPPED OVER ANGLE IRON, WRENCHING LEFT KNEE.

EMPLOYEE WAS HANDING A CABLE TO THE LINEMAN. HE SLIPPED ON SOME STONE. HE FELT PAIN IN RIGHT LEG AND BACK AND NECK.

TORN MENISCUS RIGHT KNEE. FIXING TASIL PULLEY IN PIT DOCK WORKER.

INSTALLING NEW CHAINS ON AN EXCAVATOR. SWINGING A SLEDGE HAMMER TO DRIVE PINS. STEEL BROKE OFF, HITTING HIM IN RIGHT SHIN.

PICKING UP STEEL WITH CRANE. STEEL DID NOT APPEAR TO BE SECURE. WENT TO RESTRAP AND TIGHTEN WHENSTEEL KICKED OUT CATCHING LEFT HAND.

EE WAS CARRYING GREASE GUN WALKING UP THE STAIRSAND SLIPPED AND FELL INJURING RIGHT KNEE AND LEFT ANKLE.

PULLING A HOSE ON A PROPANE TANK. WHILE PULLING HOSE, HE WAS WALKING BACKWARDS. SLIPPED ON ICE & FELL BACKWARDS.

EE GETTING OUT OF FUEL TRUCK WHEN HE STEPPED ONTO RUNNING BOARD SLIPPED ON ICE AND FELL TO GROUND. WHERE HE FELL TO THE GROUND. LANDED IN LEFT FOOT. UNDER HIM.

ON SCOW B32 TAKING MEASURMENTS (GUAGING) WITH USE OF A ROD. WHEN HE PULLED THE ROD OUT OF BARGE HE FELT A SHARP PAIN IN LOWER BACK WITH SOME NUMBNESS IN LEFT LEG.

CUTTING BELT TO SPLICE. BELT WAS ON CONVEYOR, CUT HOLE FOR ROPE SO THAT BELT COULD BE PULLED-WHEN KNIFE SLIPPED. CUT RIGHT UNDER FINGER.

WHEN INSTALLING BOOM HOIST CABLE ON MAIN DOECK STIFFLEG, EE HAD TO STAND ON TOP OF HOIST DRUM AREA TO SHIFT WRAPPED CABLE INTO PLACE. WITH THE USE OF A 4' BAR HE PUSHED ON THE BAR TO MOVE CABL E. WHEN THE CABLE MOVED INTO PLACE IT JUMPED AND THE BAR SLIPPED AND HE FELT A SNAP IN RIGHT SHOULDER.

CLIMBING OUT OF CHUTE AT ASPER CREEK SAND PLANT ONTO WALKWAY SLIPPED ON WET WALKWAY HIT LEFT SIDE AND CHEST AGAINST RAILING.

DUE TO IMCOMING RAIN STORM-WHILE SHUTING DOWN MACHINE-WENT TO CLOSE LATCH OVER ENGINE COMPARTMENT-LATCH SLIPPED AND CAUGHT FINGER.

PIECE OF STEEL UNDER TIRE OF 85 TON TRUCK- THE EMPLOYEE TRIED TO PULL IT OUT FROM UNDER TIRE, FELT SUDDEN PAIN IN GROIN AREA.

HAUL TRUCK DRIVER BEING LOADED IN QUARRY BY LOADER. OPERATOR DROPPED LOAD IN BED OF TRUCK AND SHOOK THE VEHICLE. DRIVER HIT MOUTH IN HAND HOLDING THE STEERING WHEEL AND KNOCKED TOOTH OUT.

EMPLOYEE WAS CLEANING UNDER A MOVING CONVEYOR WITH A HOE. HOE CAUGHT THE MOVING CONVEYOR AND THRUST THE EMPLOYEE'S HAND INTO AN IDLER. EMPLOYEE FAILED TO TURN OFF CONVEYOR AND LOCK OUT THE SYS TEM, WHICH IS STANDARD PROCEDURE. ALL SAFETY FEATURES WERE IN PLACE AND WAS CORDONED OFF.

EMPLOYEE WAS DOING REPAIR WORK ON SP6 AND ANOTHER EMPLOYEE WAS WELDING WITHOUT THE USE OF A SCREEN IN GENERAL AREA.

EMPLOYEE STATES THAT HE WAS TOSSED FROM SIDE TO SIDE DUE TO ROCK HITTIN GSIDE OF HAUL TRUCK WHILE BEING LOADED IN QUARRY.

SEAT ON MACHINE FROZEN IN POSITION, COULD NOT MOVE, WENT TO MOVE SEAT, PULLED OVER, STRAINED RIGHT ELBOW.

REPAIRING 1ST STANDARD CRUSHER IN #2 BID. FINISHED WELDING PLATE ON HEAD AND WAS HITTING PLATE WITH HAMMER TO MAKE SURE IT WAS SECURE. HAMMER BOUNCED & SLIPPED OUT OF HAND, HIT RIGHT SIDE OF F OREHEAD.

PUTTING DUMP CABLE ON CRANE WHENT TO TIGHTEN CABLE-CLAMP HOLDING CABLE CAME LOOSE HIT BELOW RIGHT EYET

USED A SLEDGE HAMMER TO ROUND CRUSHER WEDGES. ATFIRST EE REPORTED A SORE SHOULDER. SORENESS PERSISTED SO XRAY TAKEN. DISCOMFORT REMAINED SO WENTTO SPORT MEDICINE PHYSICIAN WHO ORDERED MRI-MRI REVEALED NO NORMAL POSTIER LABRIUM. RETD TO ORTHPEDIC DR. NO WORK WAS MISSED UNTIL 7/28/98 PENDING ORTHOPEDIC CONSULTATION.

EE CLIMBING UP LADDER OF HAUL TRUCK #2118 TO GETINTO CAB OF TRUCK. FELT PULL GROIN AREA ON LEFT SIDE.

2 EE'S WORKING ON MACHINE TO DIVERT CHUTE. EE WORKING ON TOP BELT USING WRENCH. WRENCH SLIPPED AND STRUCK EE WORKING ON BOTTOM BELT IN MOUTH

DEW FROM NIGHT AIR SETTLED AND FROZE IN LADDER OF HAUL TRUCK. WHEN SHE WENT TO CLIMB DRUM LADDER SLIPPED ON FROZEN DEW LANDED IN GROUND.

WHILE WALKING FROM PERSONAL VECHILE TO CO TRUCK IN PARKING LOT NEAR GARAGE STEPPED INTO HOLE IN GRAINED TWISTED RIGHT ANKLE.

WORKING IN MAINTENANCE SHOPMIXING CRUSHER BACKING. WILE MIXING BACKING, SPLATTERED INTO RIGHT EYE.

WHILE REPAIRING CHUTE SP1, LIFTED BIG PLATE AND FELT SOMETHING SNAP/POP RIGHT FOREARM.

WORKING ON SP3 TAKE UP PULLEY, PUTTING ON ANGLE.ANGLE SLIPPED WENT TO CATCH ANGLE, FELT PULL IN GROIN AREA.

SHOVELING AT TAILPULLEY OF SP6 AND THROWING WET MATERIAL ONTO BELT. THE WET MATERIAL SPALSHED ON BELT AND GOT INTO RIGHT EYE.

TEMPORARY TRUCK DRIVER WAS SITTING IN TRUCK. HE WENT TO SLIDE DOWN WINDOW OF DRIVER SIDE. HIS HAND SLIPPED LEVER OF WINDOW CAME DOWN AND CUT RIGHT THUMB.

WHILE PUTTING SCREENS INTO ARM TRUCK. ROPE THAT TIED SCREENS TOGETHER BROKE AND CUT MIDDLE FINGER RIGHT HAND (SPLINTER) REMOVED.

WORKING IN 4 BLDG. IN THE PROCESS OF REVERSING 5 BELT, IT STOPPED AND SPILLED. WHILE SHOVELING SPILL TRIED TO EE CHUTE SLIPPED ON SPIT AND HIT HEAD ON BEAM.

LEAVING WHEEL HOUSE OF TUGBOAT, STEPS WERE WET DUE TO HEAVY RAIN. SLIPPED IN STEPS AND CAUGHT HIMSELF WITH LEFT ARM. PULLED LIGAMENT LEFT WRIST.

WELDING TRUCK BODY ACROSS FROM GARAGE. STANDING ON LADDER. SPARK HIT CAN OF FLAMMABLE LIQUID. CAN IGNITED. CAN WAS EMPTY.

SHOVELING A SPILL AT A-1. MATERIAL WAS WET. EE WENT TO THROW WET MATERIAL OFF OF SHOVEL, THE MATERIAL DID NOT COME OFF SHOVEL, AND HE FELT A PULL IN MIDDLE OF BACK.

WORKING IN MELL, #4 BLD, PULLING GEAR BOX OFF OFQW, FELT PULL IN LOWER BACK.

WORKING 3RD FLOOR, #4 BLDG., NORTHSDIE, UNDER STAIRWAY (AT PLATFORM). EE WORKING ON STAIRWAY, CUTTING BOLTS WITH CHIPPING HAMMER. BOLT FLEW OFF--HIT EE ON TOP LIP.

WORKING IN MILL, #4 BLDG, CLEANING UP STEEL. WHILE THROWING STEEL INTO SKIFF, A PIECE THAT WAS IN SKIFF CAME OUT FROM IMPACT - HIT RIGHT FOOT.

WORKING AT SURGE TOWER - CLEANING DEBRIS AND THROWING TO GROUND DUMP AREA - PULLED RIGHT SHOULDER.

WHILE UNLOADING TANKS FROM TRUCK TO STORAGE AREA AT E TOWER HAND LEFT GOT CAUGHT BETWEEN TANKS SMASHED LEFT KING FINGER BETWEEN TANKS.

WHILE PARKED AT LOWER DOCK IN HAUL TRUCK #2120, WENT TO CROSS OVER TO TRUCK PARKED APPROX 4 FT AWAY. JUMPED TO OTHER TRUCK, AND FELL BETWEEN TRUCKS. WHILE FALLING, HIT HEAD ON ONE OF THE VEHIC LES, FELL TO THE GROUND. BRUISE LEFT SIDE AND 15 STITCHES ABOVE LEFT EAR.

OPERATING BULLDOZER IN QUARRY-SORTING & MOVING RIP RAP. DROVE OVER PIECE OF RIP RAP WITH LEFT TRACK OF BULLDOZER WHEN CAME ONTO GROUND-JARRED OPERATOR AND HE HIT HIS HEAD AND SHOULDER INSIDE OF EQUIPMENT

CLIMBING UP LADDER OF TRUCK (HAUL TRUCK) #2120 TO GET INTO VEHICLE FELT PULL - GROIN AREA - HERNIA - DIAGNOISED - OPERATION 8-29-96 - INFORMED OFFICE - 8-28-96.

WORKING IN MILL. REPAIRING CRUSHER. WHILE USING A HAMMER, SWUNG HAMMER NAD HIT THUMB OF LEFT HAND.

WORKING AT I BELT ADJUSTING SLACK IN CHAIN ON SCRAPER. WHILE ADJUSTING SLACK IN CHAIN INDEX FINGER GOT PINNED BETWEEN STEEL AND CHAIN. LACERATION INDEX FINGER.

WORKING IN THE #4 MILL BUILDING WIRING CRUSHER. WHILE TRYING TO BEND CABLE WIRE FELT PULL LOWER BACK.

UNLOADING ACETYLENE TANKS OFF OF TRUCK. WENT TO TURN AROUND WHILE HOLD TANKS AND TWISTED THE WRONG WAY. FELT PULL - LOWER BACK.

WORKING AT SURGE COMPLEX. CUTTING RUBBER FOR SPRING BAR. WHILE USING KNIFE TO CUT RUBBER, KNIFE SLIPPED AND CUT PALM OF RIGHT HAND.

WHILE DRIVING 85 TON HAUL TRUCK TRHOUGH QUARRY AREA, TRUCK TRAVELED OVER ROUGH SURFACE. FELT PULL LOWER BACK FROM BEING JARRED IN TRUCK.

EMPLOYEE WAS WORKING CHANGING ROLLERS. PICKED UP ROLLER TO PUT ON TABLE AND FINGER GOT CAUGHT BETWEEN TABLE AND ROLLER.

WALKING ALONG WALKWAY AT SURGE; SLIPPED ON A STONE TWISTED RIGHT KNEE. DEGENERATIVE TEAR - GOINGIN FOR SURGERY 2/26/96 AFTER MRI REPORT.

LIFTING PULLEY INTO PLACE IN SP-6 TUNNEL. FELT PULL IN GROIN AREA.

DRIVER AND PASSENGER WERE INJURED WHEN THE PICKUP TRUCK THEY BOTH WERE IN WENT OVER A 42' EMBANKMENT.

DRIVER AND PASSENGER WERE INJURED WHEN THE PICKUP TRUCK THEY BOTH WERE IN WENT OVER A 42' EMBANKMENT.

EMPLOYEE WAS WELDING ON DOCK PIPELINE. AFTER FINISHED TUGGING ON END CABLE THAT WAS CLIPPED TO PIPELINE. TWISTED RIGHT KNEE WHEN HE YANKED ON LEAD.

11-02-88, WORKING AT 3 BLDG. WITH A PLUGGED FEEDER. TURNING WHEEL ON THE FEEDER, FELT PULL IN LOWER BACK. DID NOT LOSE ANY TIME IN 1988.

WHILE HEATING COLLAR STARTED HAMMERING ON THE ROCK PIECE OF COLLAR BROKE OFF & WENT INTO LEFT FOREARM

WHILE BOLTING DOWN A WIRE PLATE HIT SCREW DRILLER WHEN THE SCREW DRIVER CAME DOWN LEFT 5TH FINGER CAUGHT BETWEEN SCREWDRIVER & PLATE

REPLACING RETURN IDLER AT THE CC SAND PLANT CONVEYORS PUSHING IT INTO PLACE XXX PULL IN RT SHOULDER LOST NO TIME UP TILL THIS TIME WENT OUT TO HAVE OPERATION ON SHOULDER

EMPLOYEE WAS CLIMBING DOWN THE STARBOARD STERN SID EOF THE BALKHEAD OF SCOW #13 N. HE WAS LOWERING HIMSELF DOWN FROM HE TRANSVERSE STIFFNER TO THE BARGE DECK. WHEN STEPPING OFF THE STIFFNER WITH RIGHT FOOT, HSI WEIGH TCAME DOWN ON HIS RIGHT LEG.

WORKING IN CRANE IN BUILDING #4, EMPLOYEE SAW LOAD CANOPY UP ON MILL. WHIEL CLIMBING OTU OF CRANE TO SHUT OFF FOOT SLIPPED OFF CRANE LADDER, STRIKING SHIN AGAINST STEP ON THE LADDER.

SKINNGING ELECTRICAL WIRE, WITH POCKET KNIFE. KNIFE SLIPPED CUTTING HAND.

EE WAS SETTING PLANT ROADS. THE ROAD HAD ICE ON THEM. EE JUMPED FROM BACK OF DUJP TRUCK WHERE THE SALT WAS LOCATED HE JUMPED ABOUT 4 FT TO SNOW COVERED ROADWAY HE FELL TO KNEE AND FELT PAIN IN BACK.

CLIMBING ON "L" EAST CONVEYOR FIXED PICE OF METAL ON "I" BEAM, INTO UPPER MIDDLE BACK.

MINER WAS ASSIGNED TO WORK CREW PERFORMING SEASONAL REPAIR TO AN ALLIS CHALMER 42 INCH GYRATING CRUSHER. HE WAS WORKING INSIDE THE THROAT WHERE DIAPHRAM WEAR PLATES HAD BEEN REMOVED EARLIER. H E WAS CHISELING AWAY THE FAST BACK PRODUCT THAT WAS USED TO HOLD THE DIAPHAM PLATES IN PLACE. AT THE TIME HE WAS WEARING HIS PERSONAL EYEGLASS PROTECTION WHILE CHISELING A PIECE OF FAST BACK

MINER WAS INSTALLING A NEW SET OF BUCKET TEETH ON A CAT 992 FRONT END LOADER. WHILE DRIVING A TOOTH SECURING IT TO THE BASE, MINER ACCIDENTLY STRUCK ADJACENT BUCKET TOOTH CAUSING BALL PEEN HAM MER TO MISS TOOTH PIN, THEREBY STRIKING HIS RIGHT THUMB.

MINER WAS IN TUNNEL OPERATING A RECRUSH BELT. A LEVERAGE BAR WAS HANGING FROM A CHUTE WHEEL USED TO OPEN AND CLOSE CHUTES. MINER NOTICED A HOE LAGING ONT HE FLOOR NEAR RECRUSH BELT, MIENR BE NT OVER TO PICK UP HOE HANDLE WHEN HE WENT TO STAND UP, HE FELT SOMETHING HIT HIS LEFT SHOULDER. HE TURNED HIS HEAD TO THE LEFT SIDE TO SEE WHAT HE HIT. THE LEVERAGE BAR SLIPPED OFF THE CHU

CHANGING TEETH ON A 992 CAT LOADER BUCKET,MINER DRIVING A NEW PIN IN TOOTH OF BUCKET WITH A SLEDGE HAMMER. PIECE OF METAL CHIPPED OFF AND HIT EMPL BELOW LEFT EYE.

39944ER WAS ABOUT TO WALK FROM ONE END OF SCOW TO THE OTHER TO UNTIE LINE.HE ATTEMPTED TO WALK ALONG OUTER RUNNING BOARD(GUNWALE) WHILE HAVING HIS LEFT ARM INSIDE THE CARGO BOX.JUST AS HE PASS 54023ERN BULKHEAD HE PLACED ARM OVER RAILING CATCHING HIS ARM ON BURR(METAL) ALONG RAIL.

WHILE READJUSTING SCRAPER, SCRAPER HANDLE CAUGHT BELT AND DREW HANDLE FORWARD INTO MOTOR GUARD, CUAGHT FINGER BETWEEN MOTOR GUARD AND HANDLE.

DEATH BY NATURAL CAUSES.

INJURED HAND WHILE ATTEMPTING TO TRAIN CONVEYOR WHILE CONVEYOR WAS RUNNING. CONVEYOR HAS GUARD RAIL ALONG ENTIRE LENGTH AT OUTSIDE IDLER ROLLERHEIGTH.

HAMMERING AN INNER RACE SHAFT AND A SPLINTER OF STEEL (SIZE OF A FINGER NAIL CLIPPING) CAME OFF AND LODGED IN LEFT FOREARM

TAPPING BRAKES CAM SHAFT WITH HAMMER AND SILVER OF STEEL LODGED IN LEFT THUMB.

LOWERING A PIECE OF METAL PLATE ON A ROPE DURING WINTER REPAIR SEASON AT PRIMARY CRUSHER (NOT OPERATING) METAL PLATE SWUNG AND STRUCK LEFT FOOT OF EMPLOYEE

EMPLOYEE ALLEGES HE FELT PAIN IN LOWER BACK WHILE LYING ON GROUND USING CUTTING TORCH UNDER BUCKET.

WALKING IN TO DRIVERS ROOM BEFORE SHIFT START TWISTED ANKLE ON HARD GROUND AND CHIPPED BONE.

USIN G BAR TO TIGHTEN BOLT HAND SLIPPED OFF BAR CAUSING HIM TO LOSE HIS BALANCE AND FALL 14' TO LOWER LEVEL FLOOR HEAD WAS ON FLATHEAD TRAILER AT TIME

WHILE USING A PUTTY KNIFE TO CLEAN A SEALING RING, PUTTY KNIFE SLIPPED AND STRUCK LEFT INDEX FINGER. WOUND REQUIRED SUTURING.

STANDING ON DECK OF SCOW, EMPLOYEE FELT FOREIGN SUBSTANCE IN RIGHT EYE.

EMPLOYEE WAS REPAIRING WINDOW ON EUCLID WINDOW WAS IN UP PISITON TO SECURE WINDOW IN FRAME.WINDOW SLIPPED OUT AND CAUGHT RIGHT MIDDLE FINGER AT TIP.TIP WAS ALMOST CUT OFF-NO SUTURES,FINGER TIP HELD ON WITH BANDAGE.

PUTTING WEARING PLATE ON COUNTER SHAFT. PLATE WAS NOT POSTIONED COMPLETLY SO THE MECHANICS TRIED TO PUSH IT IN PLACE. EMPLOYEE FELT PAIN IN HIS GROIN AREA.

EMPLOYEE WAS UN5OADING FULL TANKS OF OXYGEN FROM PICK UP TANK WERE STOCKED IN TRUCK TOOK ROLLED CATCHING EMPLOYEE FINGER BETWEEN TWO TANKS.

EMPLOYEES WERE 1UTTING RUBBRE SKIRTING ON D-1 CONVEYOR I.NAME WAS HOLDING RUBBERHOOK WHILE ANOTHER EMPLOYEE CUT RUBBER WITH UTILITY KNIFE KNIFE SLIPPED CUTTING EMPLOYEE ON LEFT FINGER

EMPLOYEE WAS ST5CKING (LEANING) STTEL PLATES AGAINST A PLATE.FINGER GOT PINCHED BETWEEN TWO PLATES WHILE ATTEMPTING TO REMOVE SLING.

EMPLOYEE WAS US3NG A CONVEYOR BELT CROSSOVER HE WAS GOING TO TAKE A SILO READING CLIMBING LADDER ON CROSSOVER BANGED HIS KNEE AND TWISTED LEG

EE WAS LIFTING 1LATE AT ARMOR STONE PLANE PLATE SLIPPED ON F INGER. FINGER PINCHED PLATE & CHUTE THIS CAUSED A FRACTURE OF T HE LEFT THUMB.

EMPL MOVING SCR9EN FRAME WITH COME-ALONG.SCREEN FRAME STUCK AND THEN JUMPED PINCHING FINGER BETWEEN FRAME AND WOOD BLOCKING.

WORKING SP-6 TU3NEL. HITTING WEDGE WITH SLEDGE HAMMER IN #3 CHUTE, STRUCK FINGER BETWEEN SLEDGE HAMMER HANDLE & ANGLE IRON SUPPORT

STEADING MACHIN9RY-BUILDING #3 HAND SLIPPED ON MACHINERY & RT WRIST HIT A GEAR

INSTALLING HOSE3PICKED UP HOSE SLIVER OF STEEL WENT IN LEFT RING FINGER.

EMPLOYEE WAS OP9RATING A TRUCK CRANE, DREDGING AT LOWER DOCK. IN LIFTING A LOAD OF MATERIAL, CLAMSHELL BUCKET STRUCK PILING, CAUSING CABLE AND BUCKETS TO SPIN. NOT WANTING BUCKET TO STRIKE PIP LINE BELOW , EM1LOYEE SWUNG BOOM TO RIGHT STRIKING AND BREAKING POWER LINES. BREAKERS KICKED THE POWER OFF IMMEDIATELY. NO INJURY TO OPERATOR OR DAMAGE TO CRANE.

EMPLOYEE WAS OP9RATING 988 LOADER PUT HIS HAND ON DOOR FRAME AND DOOR SHUT ON IT

EMPLOYEE WAS MO5ING A PULLEY AT OUR CC SAND SABD PLANT PULLEY SHIFTED PINCHING FINGER BETWEEN PULLEY AND CHUTE

EMPLOYEE WAS MA5ING BOLTS AT THE BLACKSMITHS SHI SHOP FOR BULLRING FOR PRIMARY CRUSHER ANVIL SLIPPED ON WHICH BOLT WAS RESTING STRIKING EMPLOYEE ON LEFT MIDDLE FINGER

EMPL ON TOP OF 6ULK POWDER TRUCK TRYING TO FREE AUGER.WHEN AUGER BROKE LOOSE EMPL LOST BALANCE AND FELL OFF SIDE OF TRUCK.

EMPLOYEE WAS DELIVERING STEMMING TO SHOT AREA TO FILL SHOT HOLES IN BLAST AREA DUMP MAN FELT GROUND MOVE UNDER HIM HE YELLED FOR DRIVER TO GET OUT OF THERE GROUND GAVE WAY AND TRUCK PLUMMETTED TO BOTTOM OF BANK

EMPLOYEE WAS USING A PROPANE TORCH TO LOOSEN MATERIAL THAT WAS FROZEN IN A SCREENING CHUTE, A LUMP OF MATERIAL BROKE LOOSE AND ROLLED , STRIKING EMPLOYEE IN LEGS

LICENSED BLASTER TESTING EQUIP IN BLAST SEQUENCE. ..BLASTER PICKED UP SEQUENTIAL BLASTING CABLE PLUG LYING ALONGSIDE OF MACHINE INSTEAD OF SHUNT PLUG.PLUGGED IT IN,PROCEEDED THROUGH TEST SEQ O F CHARGING MACHINE AND PRESSING FIRE BUTTON TO OBSERVE SEQ.BLAST FIRED. ..NO PERSONS OR EQUIP IN FIELD OF BLAST,NO INJURIES OR DAMAGE.TESTS NORMALLY RUN 10-15 MIN BEFORE SCHEDULED TIME OF BLA

EMPLOYEE INJURED HIS HEAD ARM AND BUTTOCKS AS A RESULT OF LOOSING HIS BALANCE AND FALLINGDOWN STAIRS WHEN THE SPEED HANDLE OF A WATER LINE VALVE BROKE AS HE WAS ATTEMPTING TO CLOSE IT