COLONY WEST MILL Metal/Non-Metal

Maintenance employee was removing a partial piece of an auger from the rotex deck. The auger caught on the latch as they were lowering it at waist level and it fell to the catwalk where EE was standing. It hit EE's boot across the steel toe and just behind the steel toe. This caused EE's big toe to become displaced and fractured requiring surgery.

recordable hearing shift.

Employee was training as a bulk loader with another employee. EE was attempting to close a railcar gate which is underneath the railcar. As EE pulled on the metal bar used to close the gate, the bar broke loose. Subsequently, EE stumbled backwards making contact with the corner of an adjacent railcar with the upper left portion of EE's back/shoulder area.

Employee was doing a PM on a baghouse rotary lock. Employee was kneeling down on the floor, with a foam knee pad, installing a new chain. When the employee got done employee stood up and left knee popped.

Employee hit their head on low clearance beam. Was seen by a Dr and was able to return to full duty work with no restrictions. Employee returned to Dr on 7-11-18 for lagging symptoms and was able to return to full duty no restrictions, but was placed in physical therapy.

Got finger stuck in bag clamp and it popped the finger nail out. EE had 2 stitches.

Employee was lifting a 40 lb bag and felt pain in EE's mid back. EE was evaluated by a Dr. and placed on a 20 lb lifting restriction.

Employee was opening hopper car doors on top of the railcars and one of the lids was frozen down on one end. When employee was lifting the door, employee felt a sharp pain in employee's back.

Stepped on railroad track and hurt bottom of heel.

on 7-4-15 employee was taking a guard off and felt a twinge in his back. He reported a stiff back to supervisor. Employees back felt fine the next day and was not treated by a Dr at that time. Employee contacted supervisor on 8-10-15 and wanted to get his back checked by a Dr because it was bugging him. Employee was seen on 8-11-15 and placed on a 15 pound lifting restriction.

EE was pulling on the switch and felt pain in his shoulder chest area. Employee was 11 hours into his 12 hour shift. Outside temperature was -21 degrees below zero. Dr suggested 3 or 4 days of limited use of right arm or shoulder.

EE was cutting a piece of conduit with a band saw. While doing so the saw jumped and cut his finger. He was received 4 stitches on his right index finger thus constituting in an MSHA reportable incident.

EE was stepping to the ground from the loader. EE had one foot on the ladder and one foot on the ground. His leg gave away causing him to fall on his buttock bruising his tail bone. The doctor wanted him to take 24 hours off of work.

Belly Dump gate closed while cleaning the trailer. Employee's leg was squeezed.

EE was operating the box erector putting a empty box in machine. While doing so the EE felt a sharp pain in lower back region. The doctor put him on restrictions of not lifting over 20 pounds until Jan 28th, thus constituting as a MSHA reportable accident.

EE was starting to climb a ladder and run his head into ladder cage next to him. EE was wearing a hard hat and he jammed his neck. ER gave him some muscle relaxers so thus constituting an MSHA reportable injury.

While walking up to the grizzly screen to fix a light fixture he slipped and his foot went through a hole. When EE landed his elbow hit a chuck of clay and that drove his shoulder up and started giving him pain in his shoulder. Doctor put him on restrictions affecting his regular job duties that include being an electrician, this constituting an MSHA reportable.

Contractors were removing an old elevator. A belt was in the bottom and as they cut the bottom section of the elevator out the belt caught fire. The only access to fight the fire was from the top. Could not put out fire in 30 minutes, thus constituting MSHA immediate reportability.

EE was stacking boxes of jugs on pallets and wrist/forearm started to hurt. Doctor put EE on lifting restrictions of no more than ten pounds for one week.

EE was stung by a bee on the abdomen. He started to have a slight allergic reaction. Took him to the hospital where they administered 3 antihistamine resulting in a medical treatment.

EE had been working outside throughout the day and had a call out at night as well. The weather was sub zero with a sever wind chill. EE woke up on 2/1/2011 with pain on ears. EE was diagnosed with frostbite, which is a disorder due to a physical agent, thus constituting MSHA reportability as it is a medical treatment.

EE was putting hook of car puller onto rail car when his index finger was cut, stuck in between hook and car. Took EE to doctor and doctor removed nail, put 2 stitches in and prescribed antibiotics, thus constituing MSHA reportablity.

EE was carrying an extension ladder up a flight of stairs with another EE when he felt a pop in his knee.

Employee was shoveling at tail end of a conveyor. As he was turning to dump the scoop in the wheelbarrow he strained his back. A doctor prescribed him muscle relaxers constituting MSHA reportability.

Employee was lifting a box off the line. Product at other end of line was kicking off the line and employee turned with box in hand and hurt his back.

EE was cutting a belt with a knife when the knife slipped, cutting the right forearm. Stitches were required, consituting a MSHA reportable.

EE was walking from the packaging building to the main building when he proceeded up some stairs slipping on some bentonite. When he slipped he reached out and grabbed the handrail and tore his bicep from the shoulder resulting in a injury.

EE was crossing over pallet roller conveyor and while stepping down he stepped on a misplaced pry bar causing him to sprain his right ankle. Restricted work was determined, thus constituting MSHA reportability.

Employee was throwing bags on the bag line. Two bags were sewn together, so employee grabbed them and then hurried back to the conveyor to grab the next bag, got his foot stuck under the spring board and tripped and landed on his right knee. (Restriction caused incident to be MSHA reportable) )

The EE had to walk sideways through a 23 inch walkway to go to the maintenance shop. The employee was side-stepping to the right. As the EE was free to sqare up his body, the next step is where the EE heard and felt the pop in his right foot. The EE fractured his right 5th metatarsal. A splint and restricted work was the outcome, thus resulting in the MSHA reportable.

EE working on bagline when he tripped over the springboard and fell down. He rolled his left ankle. EE was given soft ankle splint, as means of immobilizing, thus constituting MSHA reportability.

EE conducting an inventory audit and bent down to go in between railing to get to the other side. When he got to the other side, the EE stood up and felt a pain and some numbness in his back. He went to a Chiropractor, thus constituting MSHA reportability

EE unplugging roll mill, tried loosening roll prying with a bar. Felt strain to wrist. Dr requested EE to wear a wrist immobilizer for 10-14 days thus constituting MSHA reportability.

EE lifting pallet into position in stretchwrap machine and felt sharp pain in mid-back.

EE entered guarded area of palletizer, with machine running, attempting to straighten up a product box, when machine struck EE under left arm and pushed him into support post. Injuring (broke) 3 ribs on R side, bruising lung and injuring pneumothorax.

EE sliding full boxes of cat litter on floor. Stood up and while picking up box, felt pull in lower back. He was sliding boxes by pushing them to position for tank cleaning dischg. He sought Chiropractic care on 3-2-07 thus constituting MSHA reportability.

Right ring finger pinched between forklift mass framework and roller guide to mast as forks were being raised. EE was positioned on forks and being raised to count emptyware. Finger required stitches and 10 days restricted lifting was ordered.

Reported 1/31/07. Believed to have occurred shortly before 11/28/06 (1st clinic visit). EE hit head on beam under smooth rolls while walking thru pit area, thought to be a minor neck sprain. EE sought medical exam, xrays and MRI, negative results. Physical therapy prescribed thus constituting MSHA reportability. No restrictions noted. (Did several p/t visits).

After dumping dumpster, EE tried to 'kick' an empty container into the dumpster, but when he went to kick it, it was frozen to the ground. This action injured left foot due to container not moving when he kicked it. He later had the foot x-rayed & it was determined that there was a small fracture to the big toe, thus constituting MSHA reportability. (Positive diagnostic xray)

EE was putting plastic lids on jugs and started feeling pain in right hand. Continued task, pain worsened, he was moved to different work station. Thought swelling would lessen but didn't, so a week later he went to Dr. Dr. placed him on restricted duty (not to use hand) thus constituting MSHA reportabiltiy (work restrictions).

EE was carrying roll of plastic to bag inserter machine, and felt pain in lower back.

EE driving forklift, stacking pallets, debris fell into his eye from a piece of wood, causing corneal abrasion.

EE was getting into dump truck and while sliding right leg under the steering wheel, his right knee popped out (dislocated).

Stepping over line by the taper, when stepping down cut hand/finger on sharp edge of 110 plug-in. Stitches required - MSHA reportable.

EE HAD JUST ARRIVED AT JOB SITE, AND WAS USING A BOX KNIFE TO CUT LOOSE STRING FROM HIS BLUE JEAN PANT LEG, AND CUT HIS LEFT FOREARM. HE WAS TO TAKEN TO CLINIC AND REC'D STITCHES TO CLOSE THE WOUND. (MSHA REPORTABILITY)

HERNIA DIAGNOSIS THAT EMPLOYEE REPORTED 7-28-05, AS HE HAD SURGERY SCHEDULED 7-29-05.

EE STEPPED ON FORKLIFT WHEEL TO EMPTY DUMPSTER AND SLIPPED, PULLING LEFT GROIN AREA. EE WAS PRESCRIBED 2 WEEKS OF PHYSICAL THERAPY, BUT NO LIGHT OR RESTRICTED DUTY, THUS CONSTITUTING MSHA REPORTABILITY.

EE was moving steps to treater so he could clean up. He did not notice a piece of metal leaning on ladder, when steps moved, the metal fell on right thumb, pinching it between ladder and metal piece. Fracture to thumb.

Ee was struck on top of head with pallet of empty ware being slid into place by a forklift. Neck strain. Ee received physical therapy. Medical treatment.

Employee's left arm started having sharp pain when throwing jugs in box. Poosible tendonitis. Exam 1/3/05, and light duty was prescribed. Not immediately available, so lost time resulted also. His arm was also immobilized temporarily with wrist splint, at time of Dr visit 1/3/05.

EE was stacking 30 lb product when took box off conveyer, turned to put it on the pallet and felt a pull in his back near rib area. EE sought chiropractic treatment thus constituting MSHA reportability.

EE was tightening bolt to adjust all fill when wrench slipped off bolt and hit right hand on air cylinder, bruising hand.

EE was throwing 30 lb boxes of cat litter on to a pallet when he twisted his lower back. Sought chiropractic care, thus constituting MSHA reportability, additionally lost time.

EE TURNED TO PLACE 30# PAIL OF PRODUCT ON PALLET DURING PALLETIZATION, FELT SHARP PAIN IN LOWER BACK FROM MOVEMENT, TWISTING, ETC. EE SOUGHT CHIROPRACTIC CARE, THUS CONSTITUTING MSHA REPORTABLILITY.

EE WAS WRESTLING WITH ANOTHER EE WHEN FINGER JAMMED AGAINST A PALLET. FINGER FRACTURED AND EE LOST 1 DAY OF WORK.

EE WAS USING A BOX CUTTER KNIFE TO OPEN EMPTY WARE PALLETS. KNIFE WAS NOT RETRACTED & HE WAS PUTTING EMPTYWARE ON THE LINE, PUSHING BOXES & HAD KNIFE IN ONE HAND. RIGHT ARM WENT OVER LEFT HAND AND BLADE CUT RIGHT FOREARM. REQUIRED STITCHES, THUS CONSTITUTING MSHA REPORTABILITY.

EE REPORTS KICKING A JUG OF CAT LITTER AND STOMPING ON AN EMPTY JUG TWICE. STRAIN TO FOOT, DEVELOPED INTO TENDONITIS. MISSED A WEEK OF WORK, THUS CONSTITUTING LOST TIME. RETURNED 5-25. REPORTE D INCIDENT ON 5-28 AS WORK RELATED.

EE WAS DRILLING A HOLE INTO AN ALUMINUM CABLE. A SMALL ALUMINUM FRAGMENT BECAME LODGED IN EYE. EMBEDDED - SURGICALLY REMOVED, AND PRESCRIPTION WAS PRESCRIBED. THUS CONSTITUTING MSHA REPORTABIL ITY.

EE WAS CUTTING STRAPS OFF THE BUNDLES OF EMPTYWARE AND CUT HIS FINGER WITH A UTILITY KNIFE. REQUIRED STITCHES, THUS CONSTITUTING MSHA REPORTABILITY.

EE WAS LIFTING ROLL OF PLASTIC BY HIMSELF, STRAINED BACK.

EE WAS LIFTING A LAYER OF 16# EMPTYWARE AND FELT PAIN IN THE MIDDLE OF HIS BACK. CHIROPRACTIC CARE AND 2 DAYS MISSED WORK CONSTITUTE MSHA REPORTABILITY.

EE WAS LIFTING CONVEYOR TO RE-BRACE TO MAKE LEVEL WITH TAPE MACHINE. HERNIATED LEFT GROIN AREA.

EE DIAGNOSIS 2-21-02 CARPUAL TUNNEL SYNDROME. SURGERY DATE 2-26-02. RETURN TO WORK DATE PLANNED 3-8-02. LOST TIME. INJURED REPORTED BY WORK TO BE FROM CAT LITTER LINE WORK-REPETATIVE MOTION SC REWING LIDS, ETC. HE INDICATED.

EE WAS INVOLVED IN HORSEPLAY. ANOTHER EE CAME BEHIND HIM AND LOCKED HIS HANDS BETWEEN HIS LEGS AND LIFTED HIM BY HIS SCROTUM, AGGRAVATING HYDROCELE.

EMPLOYEE SUFFERED A LOWER BACK STRAIN, SHOVELING CLAY.

EE STEPPED OFF CATWALK. RIGHT FOOT DROPPED 12" &CAUSED FALL. TWISTED RIGHT ANKLE. ANKLE WAS CAST& IMMOBILIZED.

EMPLOYEE HIT HAND ON THE BAG SPOUT WHILE LIFTING A BAG. IT TORE. SUFFERED A HAND BRUISE AND MISSED 1 DAY OF WORK, CONSTITUTING MSHA REPORTABILITY.

EE WAS PULLING ON A CONVEYOR TO STRAIGHTEN OUT. HE STRAINED HIS MID-UPPER BACK BETWEEN SHOULDER BLADES. HE RESTRAINED SAME AREA 2/19. HE SAW A CHIROPRACTOR ON AT LEAST 2 SEPARATE OCCASIONS, & LOST TIME (SENT HOME 2/20 & ABSENT 2/21/01).

EE STRAINED A GROIN MUSCLE, WHILE HANDLING MATERIALS, LIFTING.

EMPLOYEE WAS DIAGNOSED WITH CARPAL TUNNEL AS A RESULT OF REPETITIOUS WORK IN THE CAT LITTER LINE. HE HAD SURGERY ON 9/20/00, RESULTING IN 1 LOST TIME DAY.

EE DIAGNOSED WITH CARPAL TUNNEL--SURGERY 8/21, ABSENT 8/22 ALSO. (LOST TIME)

EMPLOYEE EXPERIENCED PAIN IN LOWER BACK WHILE WORKING PRODUCTION LINE. REPETITIVE MOTION, BENDING, TWISTING, TURNING, LIFTING, MATERIALS HANDLING. FELT PAIN IN LOWR BACK AREA, BACK STRAIN, 50 # BAGS OF MATERIAL.

REPEATED LIFTING AND TWISTING WHILE THROWING BOXES ON THE CAT LITTER LINE (ASSEMBLY LINE) 2 X 30 LB AT A TIME. LOWER BACK PAIN RADIATING TO THE LEG.

EE'S STOMACH STARTED TO HURT AND THEN A LUMP APPEARED. HE WENT TO A PHYSICIAN WHO DIAGNOSED IT AS A HERNIA CONDITION. SURGICAL REPAIR WAS PLANNED.

LOWER BACK PAIN FROM MATERIALS HANDLING METHODS/ MOVEMENT, ETC. CHIROPRACTIC VISITS/ LOST TIME.

EMPLOYEE BENT OVER TO PICK UP A BOX OF TREAT TO PUT IN THE MILLING AUGER. BECAUSE IT WAS ABOUT FULL, HE PUT IT BACK ON THE BASE. HE STRAINED HISBACK DOING THIS.

LOWER BACK PAIN.

EMPLOYEE WAS WALKING DOWN STAIRS INTO THE DRYER ROOM. HE SLIPPED ON LAST STAIR AND SPRAINED ANKLE. HE MISSED 2 DAYS OF WORK, LOST TIME INJURY- REPORTABLE.

EE CUT LEFT INDEX FINGER WITH A BOX CUTTER WHILE OPENING A BOX. CUT REQUIRED STITCHES THUS CONSTITUTING MSHA REPORTABILITY.

EE WAS STACKING BOXES ON A PALLET. HE FELT A SHARP PAIN IN THE MIDDLE OF HIS BACK. LEFT WORK AND SOUGHT CHIROPRACTIC TREATMENT HTUS CONSTITUTING MSHA REPORTABLILITY.

WHILE STACKING A PALLET OF MATERIAL, EMPLOYEE FRACTURED LEFT WRIST.

EE WAS LIFTING PLASTIC JUGS FROM STACK FROM OVER HIS HEAD. SLIPPED BACKWARDS - FELT PAIN AND BURNING SENSATION IN GROIN AREA (RIGHT SIDE). LATER DETERMINED TO BE A HERNIA SITUATION BY DR.

EE WAS THROWING BAGS OF BENTONITE AND NOTICED HIS BACK BEGINING TO HURT. BY THE END OF THE DAY, HE WAS IN PAIN. HE MISSED WORK 1 DAY, 10-5-98, CONSTITUTING LOST TIME REPORTABLILITY.

EMPLOYEE WAS GRINDING ON A PIECE OF METAL AND A PIECE OF IT WENT INTO HIS EYE. (LEFT EYE).

EE GOT A SHARP PAIN IN THE UPPER LEFYT SHOULDER WHILE THROWING BOXES, ONTO A STACK HIGHER & HIGHER.

EE OPEING GATE ON TRAINCAR. IT GOT STUCK AND HE WAS USING A PRYBAR TO OPEN THE GATE. HE WAS PUSHING ON THE BAR WHEN THE GATE OPENED AND JAMMED HIS NECK BACK CAUSING PAIN AT BASE OF NECK. SUBSE QUENT CHIROPRACTIC VISITS CONSTITUTE REPORTABLILITY FOR MSHA REQUIREMENTS.

EE WAS CUTTING CARDBOARD. THE RAZOR KNIFE SLIPPED AND HE STABBED HIMSELF IN THE PALM OF HIS LEFT HAND. LACERATION REQUIRED STITCHES.

EE WAS LIFTING CHANNEL IRON ON TO ROOF. HE DISLOCATED HIS LOWER BACK. ***CHIRPORACTIC VISIT 4/9/98 DEEMED REPORTABILITY.

EE CUT LEFT SMALL FINGER WITH RAZOR BLADE KNIFE WHILE CUTTING SLITS IN LID TO OPEN IT ON A 5-GAL. PAIL.

REPETITION WORK RELATED TO PACKAGING CAT LITTER CAUSING SORENESS IN LEFT WRIST. EMP INSTRUCTED TO DO ALTERNATIVE WORK FOR 10-14 DAYS AND KEEP WRIST SPLINT ON AT WORK FOR IMMOBILIZATION OF INJU RED WRIST CONSTITUTING MEDICAL REPORTABILITY.

EE WAS CLIMBING UP & DOWN ON A STEEL STRUCTURE. WHEN HE GOT DOWN OFF THE STRUCTURE, HE TWISTED WRONG & FELT A PULL IN THE MIDDLE OF HIS BACK & WENT AROUND TO THE FRONT SIDE OF HIS CHEST.

ABRASION TO EYE. EE WAS LOOKING UP TO CHECK OUT NEW DEFLECTION SHEET WHEN A PIECE OF BENTONITE CLAY FELL AND WENT IN BETWEEN HIS GLASSES AND FACE, HITTING HIS RIGHT EYE.

EMP BENT OVER TO PICK UP A 5" ROUND PIECE OF PIPE WHEN HIS LOWER BACK POPPED.

EE WAS SEWING BAGS WHEN HE FELT A PAIN IN HIS LEFT SHOULDER.

EE HAD HIS RIGHT HAND ON TRUCK RAM WHILE TALKINGTO A TRUCKER. THE EE, UPON LEAVING, SLID HIS RIGHT HAND ACROSS THE RAMP CUTTING IT ON JAGGED METAL. THIS CUT DID REQUIRE STITCHES.

EE WAS THROWING 25# BAGS, TWISTED THE WRONG WAY AND FELT A POP IN LOWER BACK.

EE THOUGHT THAT POWER TO THE SEWING MACHINE WAS OFF SINCE THE BULB WAS NOT ON. HOWEVER, THE BULB WAS BURNED OUT AND POWER WAS ON. EE WAS THREADING THE NEEDLE WHEN THE MACHINE STARTED CAUSING T HE NEEDLE TO PUNCTURE HIS LEFT INDEX FINGER.

POWDER FROM TOP OF THE LITTER PURRFECT PACKER FELL INTO LEFT EYE OF EE WHILE HE WAS LOOKING UP AT THE SLIDE.

EE WAS MOVING BULKHEAD DOOR IN BOXCAR WHEN RIGHT HAND BECAME LODGED BETWEEN THE DOOR AND THE WALL OF THE BOXCAR. RIGHT HAND WAS BRUISED.

EMPLLOYEE WAS CLOSING BOTTOM GATE ON OPEN TOP CAR. WHEN GATE SLAMMED SHUT, WITH HAND ON LEVER OF GATE, THE JOLT CRACKED AN OLD FRACTURE ON HIS RIGHT HAND.

EE WAS WALKING FROM THE OFFICE TO THE PLANT, SLIPPED ON ICE & FELL CAUSING RIB ON LEFT SIDE TO BECOME FRACTURED.

EE WAS PULLING A BUNDLE OF EMPTYWARE JUGS AND TWISTED HIS BACK.

EE BENT OVER TO PICK UP A STRETCH WRAP ROLL. HURT LOWER BACK.

EE WAS CLIMBING UP LADDER TO CHECK GAUGES ON BAGHOUSE PIPES. THE LADDER WAS NOT POSITIONED PROPERLY AND WHEN EE LEANED OVER TO READ GAUAGE AND THE LADDER FELL OVER CAUSING THE EE TO FALL TO TH E GROUND.

EMPLOYEE WAS REMOVING INSPECTION DOOR FROM HAMMER MILL. HAMMER WAS LAYING IN OPENING, FELL AND HIT LEFT FOOT, BROKE LITTLE TOE.

EMPLOYEE WAS CUTTING OPEN A BOX OF LIDS AND TH EKNIFE SLIPPED AND CUT HIS FINGER.

WHILE THE EMPLOYEE WAS PULLING LADDER UP THE SIDE OF THE RAILCAR HE WAS BACKING UP AT WHICH POINT HE FELL INTO ONE OF THE EMPTY CARGO HOLES AND DISLOCATED HIS SHOULDER.

EMPLOYEE WAS CUTTING BOXES OPEN WHEN KNIFE CAME IN CONTACT WITH TWO FINGERS ON LEFT HAND. THE CUTS REQUIRED STITCHES.

EMPLOYEE WAS HLEPIN GTO GET THE GRANNY AUGER GOIN. WHEN MOTOR KICKED OUT, EMPLOYEE MANUALLY BACKED THE AUGER BY PULLING HTE V BELTS. WHEN MOTOR CAME ON, EMPLOYEES LEFT HAND WAS PULLED THROUG H THE SHEAVE.

EE WAS TURNING THE CUTTING EDGE ON THE FRONT END LOADER AND PULLED STOMACH MUSCLES WHILE LIFTING THE CORNER SECTION.

EMPLOYEE WAS TRYING TO GET SLIDE ON PACKER TO MOVE FREELY WHEN LEFT FOOT WAS PUT INTO PART OF SLIDE SLIDE RELEASED & LEFT FOOT WAS SMASHED

EE WAS THROWING BAGS ON TO A PALLET FROM THE CONVEYOR BELT. HE FELT A LITTLE BIT OF A PAIN IN HIS BACK (LOWER PART).

EMPLOYEE WAS OPERATING THE WINCH CONTROL BOTTOM WITH HIS RIGHT HAND WHILE HOLDING THE SLACK ROPE IN HIS LEFT HAND. THE CAR PULLER ROPE SLIPPED ON THE SPOOL CAUSING THE ROPE TO BE JERKED FROM H IS LEFT HAND. THIS CAUSED A BONE IN HIS LEFT WRIST TO BREAK.

EMPL REMOVED CAP FROM VEIN FEEDER TO PERFORM MAINT.CHECK AND REPLACING THE CAP IT SLIPPED FROM HAND.HE GRABBED FOR IT AND LEFT INDEX FINGER ENTERED HOLE CAUSING TIP TO BE SEVERED.

SERVALL ROUTE DRIVER CHANGING RUGS IN HALL BY LUNCHROOM.AS HE BENT OVER TO PICK UP RUG,HAD PAIN IN LOWER LEFT BACK.WAS UNABLE TO STRAIGHTEN UP AT THIS TIME.

EMPL WAS GETTING OUT OF PICKUP AFTER PARKING IN LOT AT OFFICE. UPON GETTING OUT OF PICKUP HE FELL ON ICE CAUSING TAILBONE TO BECOME BROKEN.

EMPLOYEE WAS MOVING A DOOR INSIDE A BOX CAR. THE DOOR DID NOT UNHOOK FROM THE TOP WHICH CAUSED THE BOTTOM TO SWING OUT PINNING HIS LEFT FOOT BETWEEN THE DOOR AND THE FLOOR. EMPLOYEES LEFT FO OT WAS BRUISED.

WHILE ATTEMPTING TO ASSIST AND EMP. LIFT A RAMER LAB EQUIP. THE RAMER SLIPPED FROM THE OTHER EMP. GRIP THUS SMASHING THE MIDDLE FINGER LEFT HAND, OF EMP.

EMPLOYEE WAS CLEANING THE DRYER CHUTES AND STEPPED ON A CLEANING ROD AND SPRAINED HIS LEFT ANKLE.

EMPLOYEE WAS GE7TING INTO D8 CAT WHEN HIS LEFT HAND BECAME CAUGHT IN THE DOOR BREAKING THE FIRST BONE AND BRUISING THE SECOND BONE OF THE LITTLE FINGER.

EMPLOYEE WAS TH9OWING 50# BAGS OF BENTONITE OFF THE THREE SPOUT PACKER WHEN HE REACHED FOR A BAG HE CAUGHT HIS RT HAND BETWEEN THE SPRING ROLLER AND BAG SLIDE ROLLERS HE BRUISED HIS RT HAND

OVER PROLONGED 1ERIOD OF TIME OF THROWING BAGS,EMPL SWITCHED SIDES OF THROWING AND GOT TENDONITITHIS CAUSED SWELLING THE TENDONITIS.

WHILE BAGGING GROUND BENTONITE THE TOP BLEW OUT ON THE BAG AND BENTONITE BLEW UP UNDER EMPLOYEES SAFETY GLASSES CAUSING SEVERE EYE IRRITATION.

EMP WAS STEPPING FROM BULK TRUCK HE MISSED THE PLATFORM AND FELL BREAKING HIS ANKLE

INJURED EMPLOYEE WAS HOLDING END OF A PC OF STEEL (THAT WAS SECURED IN A VICE) WITH A PAIR OF CHANNEL LOCK PLIERS ANOTHER EMPLOYEE WAS GRINDING ON THE PIECE OF STEEL WITH A PORTABLE GRINDER DU RING THE PROCESS THE GRINDER KICKED BACK AND HIT THE INJUREDS RIGHT FOREFINGER RESULTING IN A LACERATION REQUIRING STITCHES