COLONY EAST MILL: 266 citaciones de la MSHA Metal/Non-Metal

Employee was loading rail cars and walking on/near the tracks. EE felt a poke in the foot and discovered a piece of wire had punctured the sole of EE's boot and entered EE's foot.

Lab tech lifted bucket (approx. 20 lbs.) about 36 inches over a rail to dump into a dumpster felt a pop. EE refused medical care at that time, iced and monitored it. Next day EE stated it felt better. On 10-26-21 EE stated it wasn't getting better and wanted to see a Dr. EE was given restriction and Tylenol. On 11-24-21 MRI was performed. Surgery was scheduled for 12-16-21.

Employee was cleaning rail cars. Employee came to a door that was difficult to open and pushed on the bar employee was using harder. The door freed up and the employee hit the ground with left shoulder.

Employee pushed open a door to go to the locker room at the end of the shift. The kick plate on the door pulled loose and got wedged in the door way. The employee walked through the door and tripped over the kick plate stuck in the door way.

Employee was cleaning out an elevator when EE's elbow began to hurt.

EE was cleaning with a loader and dug a hole in the ground. EE then backed into it and injured back.

EE was filling windshield wash reservoir and it squirted into right eye. Employee was wearing safety glasses. The fluid came up and under the bottom of the glasses.

Employee walked into the maint shop with muddy shoes and slipped and hurt knee. Could not walk on it after it happened. EE was seen by a Dr. and possible torn ligaments.

Employee was using a pry bar as a hammer and felt their shoulder pop, but said they were fine. Their shoulder started hurting worse on 8-16-16 so they were taken to the dr for evaluation. Dr put employee on restrictions until seen by orthopedic dr.

Hit rock with loader and the back end of loader bounced and jarred employee's back

Employee welding and received burn to groin area

Pregnant employee missed a step and fell hitting the top of her belly. She was taken into the ER just as a precaution because she was pregnant and they decided to keep her overnight because she is a high risk pregnancy. She was released the next day.

One loader backed up and ran into another loader and employee complained of neck pain.

Reporting a recordable shift in hearing

Reporting a recordable shift in hearing

EE was barring out pit and felt pain on lower back. We scheduled EE appointment at clinic and clinic started him on physical therapy with no restrictions. Thus constituting as an MSHA reportable pertaining to physical therapy.

EE was changing heater hose on a loader while doing so he hit his hand on a hose clamp and cut his hand. The EE received 2 stitches on the top of his hand. This constituting as an MSHA reportable accident.

EE was going down to the car puller to unhook the winch and while doing so he rolled his ankle. EE went to the ER and they put him in an air cast and no restrictions, this constituting in an MSHA reportable accident.

EE was re-stacking pallets with broken bags on them. EE felt pain in lower wrist. Doctor placed EE on restricted duty of no lifting with left hand for 5 days, thus constituting MSHA reportability.

EE was unplugging coal auger and couldn't reach all the plugged material. Added air to it and a burst of fire burned EE on face. EE was prescribed ointment for 1st degree burns thus constituting MSHA reportability.

EE was throwing 100 pound bags. Felt pain in wrist at the end of shift. Went to doctor on 11/30 and was told EE had tendonitis. Restrictions of not lifting anything over 10 pounds was put on EE resulting in MSHA reportablity.

Employee was removing a guard to work on a return spool for a railcar mover, when he felt a twinge in his lower back.

Employee was using a sledge hammer to clean out chunks off the dryer. Employee hit side of chunk and hit back wall of dryer hurting his left shoulder. Employee was put on restrictive duty, constituting MSHA reportable.

Employee was unplugging the coal pulverizer when he got burned by a blast of fire - burned his arm and lips. The burns were deemed 1st degree and employee was given prescription ointment, constituting MSHA reportable.

A Loader Operator was spreading dried material on a slick ramp and the wind was blowing N.W. 5 to 15 mph. The wind blew back the material on the windshield of the loader, the operator could not see the truck coming up on the right side and turned to the right tearing off the cab of the truck.

EE was stretch wrapping a pallet of 50# bags of bentonite, when he stepped beween the forklift stop and the moving stretch wrapper. The pallet that the bags were on, pinned his left leg between the forklift stop and the pallet of bags, causing bruising of the leg and light duty work.

EE was throwing 100# bag when he felt some pain in left forearm. Told his leadman who in turn reported it to the plant supervisor.

EE using jackhammer to bar at hammer mill. Turned to move hammer to left side of mill door and got his left pinky finger knuckle pinched between bottom left of the door edge and jackhammer.

EE was using 1/2"drill, drilling out fluid bed dryer grid. Drill jammed, causing the drill and EE's R wrist to continue in a clockwise motion. Twisting caused wrist to rapidly go into strained position, causing wrist strain. Wrist was immobilized with a splint, thus constituting MSHA reportability.

EE hit chin on bulk bag machine support arm when bag strap fell off, causing arm to move upward. Received stiched to cut.

Employees were baring out coal chute to Rotary Dryer when they started to fell dizzy and light headed. They noticed a smell when entering room but thought it was nothing. They were taken to ER for possible carbon monoxide inhalation, given a 1 time dose of oxygen and put on light duty for the following day (1 shift)

EE's were baring out coal chute to Rotary Dryer, when they started to feel dizzy and light headed. They noticed a smell when entering room, but thought it was nothing. They were taken to ER for possible carbon monoxide inhalation and given a one time dose of oxygen and put on light duty for the following day (1 shift).

While stepping off working platform at coal pulverizing feeder, EE missed top rung with foot sudden drop and catching himself from falling-jarred lower back. He missed 2 days of work and sought chiropractic care thus constituting MSHA reportability. MIssed 5/12 and 5/13, not scheduled 5/14, returned 5/15 w/o restrictions

Ee was unhooking wench cable from hopper railcar so it could be pulled back. While attempting to remove hook from car by using hands to pull on it, hook and ee hand hit him in the mouth, chipping tooth

While throwing 100 lb. bags of material, left wrist started to hurt and began to swell. Diagnosed as wrist strain. He received temp. usage restriction to graduate to 100% usage in 2 weeks (restricted duty). Did not go to the doctor until 3-6-07, that is diagnosis date.

dusty and noisy 1/17/07: called Rick to obtain more information. EE was running a hoist, shive 056got bound, because of noise & dust, EE could not hear radio and the cable struck his thumb.

Employee's right foot was run over by right rear tire of forklift. Operator did not see him sweeping the floor behind him while backing up. Bruised foot.

EE sliding and lifting wooden blocks weighing approx.75lbs into place under loader to use for support during repairs. Felt pull in lower back right area. Sought Chirporactic care- this consituting medical treatment MSHA reportability.

EE cleaning trough roller on 2A belt conveyor, when right index finger was caught between roller and syntron pan feeder on 4/22/2006. On 5/2/06, EE decided to seek medical attn. X-ray taken on 5/2/06 revealed finger tip fracture, thus constituting MSHA rptblty on that date. No work restrictions ordered, no lost time.

EE was throwing 100 lb bag of bentonite onto a pallet and felt a pop in lower left forearm by wrist.

EE drilling hole thru metal angle iron using electric drill when drill bit caught in metal and pulled drill out of hands, fracturing right hand.

Ee was exting bobcat skidsteer loader and didn't notice support beam for granular bulk truck load out canopy. He hit head on support beam and wrenched neck. He was examined with a negative x ray, but a smucle relaxer was preseribed and 1 shift of work was missed. Physician ordered 1 shift to be missed-that he not return that next evening.

EE was barring hammermill from breaker plate door and hammers were not done spinning. Bar made contact with hammers smashing right thumb between bar and hammermill housing wall. EE required 3 stitches.

EE slipped while dismounting loader - pulled/strained left shoulder. Lifting restriction.

Ee accident/diagnosis as Muscle Strain on 7-15-05. 12-27-05 ee noticed lump in area of strain and sought medical opinion 2 dr . 1 st did not, but 2nd did diagnose it as a hernia on 1-3-06. he returned to work that afternoon and hernia surgery was scheduled for friday 1-6-06.

EE slipped on expanded metal walking surface because of outside weather conditions being foggy and cold, made walking surface extremely slippery. Fell backwards on back and neck. Lost time reportability.

Ee tripped on a shovel, lost balance and fell backwards on extended left arm awkwardly. broke tip off radius bone in left forearm at elbow.

EE WAS ROLLING STRUCTURE THAT SUPPORTS AN OVERHEAD HOIST INTO POSITION TO REMOVE THE ENGINE ON SWITCHMASTER BY PUSHING AND PULLING THE STRUCTURE. INJURED BACK BY DOING THIS.

EE WAS POSITIONING COMPRESSOR INTO PLACE USING A BAR AND PRYING MOTION WHEN HE FELT A TIGHTNESS IN LOWER BACK AREA. EE SOUGHT CHIROPRACTIC CARE AND HAD SOME LOST TIME, THUS CONSTITUTING MSHA REPORTABILITY.

EE WAS DISMOUNTING RAILCAR MOVER, STEPPED FROM LAST STEP TO GROUND & FELT POP IN HIS KNEE.(LEFT).

EMPLOYEE LOST BALANCE AND FELL BACKWARDS THROUGH A DOOR OPENING APPROX. 9 FT. TO THE GROUND LANDING ON HIS HEAD. NO SERIOUS INJURY WAS RECEIVED. HE WAS RELEASED FROM ER, GIVEN PAIN MEDICATION AND LOST TIME RECUPERATING AT HOME.

ANOTHER EE WAS LOOSENING BELT ON #1 MILL WHEN THE BELT LOOSENED THE BAR HE WAS USING STRUCK EE IN THE MOUTH CHIPPING HIS TOOTH. HE WAS JUST ENTERING THE AREA WHEN THIS HAPPENED. IT WILL REQUIR E DENTAL REPAIR AND IT IS PERMANENT TOOTH TO BE CROWNED THUS CONSTITUTING MSHA REPORTABLILITY CFR PART 50 PAGE 37.

EE STEPPED ON CHUNK OF BENTONITE AND TWISTED KNEE. EE WAS STARTING UP DRYER. HE WENT TO UNLOCK TOOL BOX AND SIREN SOUNDED. HE WAS RUNNING TO CONTROL ROOM AND A CHUNK OF BENTONITE FELL FROM THE INCLINE BELT, HE STEPPED ON IT AND TWISTED HIS RT. KNEE.

LOADER OPERATOR SHUT DOWN PRIMARY SYSTEM TO CLEAN HAMMERMILL BREAKER PLATE AREA. THIS ACTION WILL AUTOMATICALLY SHUT OFF 2A BELT. HE DID NOT SHUT OFF THE FIRES TO THE VIBRATING PAN FEEDER WHIC H ARE LOCATED DIRECTLY ABOVE 2A BELT IN THE CRUDE PIT AREA. BECAUSE THE CLEANING TOOK LONGER THAN ANTICIPATED THE HEAT GENERATED FROM THE PAN FIRES IGNITED 2A BELT & THE SLIDER BED.

EYE IRRITATION FROM A PIECE OF METAL (RUST) THAT WAS EMBEDDED IN THE EYE AND HAD TO BE REMOVED. EYE DROPS WERE PRESCRIBED ALSO. CONSTITUTES MEDICAL TREATMENT FOR MSHA REPORTABILITY.

EE PULLING CAR DIVIDER CLOSED IN RAILCAR. RIGHT FOOT CAUGHT UNDER DIVIDER, SMASHING TOES. BIG TOE BROKEN, REST BADLY BRUISED. LOST TIME INJURY (1 WK).

EE STRAINED LOWER BACK WHILE THROWING STACKING 100 LBS BAGS OF CLAY INTO A RAILROAD BOXCAR. MISSED 2 DAYS OF WORK, AND SOUGHT CHIROPRACTIC CARE CONSTITUTION MSHA REPORTABILITY TOOK 2 DAYS OFF VACATION.

EE WAS CLEANING OFF A SCREEN AND TWISTED HIS BACK. HE WENT TO A CHIROPRACTOR THUS CONSTITUTING MSHA REPORTABILITY.

BACK STRAIN WHILE STACKING BAGS ONTO PALLETS COMING OFF CONVEYOR BELT. TWISTING, TURNING, LIFTING MOTION. CHIRO VISITS AND 3 DAYS LOST TIME CONSTITUTE MSHA REPORTABILITY.

EE STRAINED BACK WHILE LIFTING/TURNING MOTION BARREL. WENT TO CHIROPRACTOR CONSITUTING MSHA REPORTABILITY

EE STRAINED BACK WHILE LFITING/TURNING MOTION WENT TO CHIROPRACTOR 4/4/00 CONSTITUTING MSHA REPORTABILITY AT THAT TIME

WHILE COMING DOWN THE ACCESS LADDER OFF THE LOADER, HE LOST HIS FOOTING AND FELL. SNOWY SLIPPERY ICY CONDITIONS CONTRIBUTED. STRAIN/SPRAIN TO ANKLE. LOST DAYS (5).

WHILE STACKING 100LB BAGS ONTO A PALLET LOWER BACK STARTED TO SPASM & CRAMP UP. WENT TO CHRIOPRACTOR AND LOST TIME 1 DAY 7/17/99 TO CAUSE MSHA REPORTABLILITY

WHILE STEPPING FROM THE FRONT END LOADER OVER TO A CATWALK PLATFORM, EE LOST FOOTING AND HANDHOLD, FALLING TO THE GROUND. INJURY TO LOWER BACK (BULGED DISC.)

WHILE TESTING GROUND ON A SCREEN, EE TOUCHED THE SCREEN AT THE SAME TIME, THUS RECEIVING AN ELECTRICAL SHOCK. NOTED AS ELECTRICAL TRAUMA.HAD SURGERY ON 5-11-2000, RESULTING IN LOST TIME. POSSI BLE PARESTHESIS OF UPPER RIGHT EXTREMITY AND POSSIBLE DAMAGE TO THE RADIAL NERVE.

EE WAS BORING A ROCK OUT OF THE BOTTOM OF THE ROTARY CRUDE PIT. HE STARTED TO FALL OVER BACKWARDS AND TRIED TO CATCH HIMSELF AND HIT HIS RIGHT WRIST ON A STEEL PLATE.

WHILE OPERATING D8 DOZER, WENT OVER SHARP EMBANKMENT CAUSING DOZER TO SHIFT FROM SIDE TO SIDE AND DOWN SUDDENLY.

EMPLOYEE WAS UNCOUPLING CARS. WHEN HE OPENED KNUCKLE IT ROLLED AHEAD, BRAKES DIDN'T HOLD AND HE PINCHED HIS LOWER RIGHT FOREARM. IT WAS BADLY BRUISED.

DEVERTER TO THE BOX CAR TRACK STUCK, TURNED MANUAL HANDLE TO HELP OPEN DEVERTER, THEN HE WENT TO TURN THE ELECTRICAL SWITCH FOR DEVERTER ON AND GOT SHOCKED.

BACK STRAIN.

WHILE BULK BAGGING, THE EE PULLED THE FILLER HOSE OUT OF THE BAG AND FELT SOMETHING GIVE IN HIS LOWER BACK CAUSING HIS RIGHT LEG TO BECOME NUMB.

EMP JUMPED FROM TOP RUNG OF LOADER TO THE CATWALK. TWISTED RIGHT FOOT CAUSING A SPRAIN.

EE WAS TRYING TO ALIGN MOTOR MOUNT BOLTS UP TO A MOTOR WHEN THE MOTOR SLIPPED OFF THE FORKS OF THE FORK LIFT, LANDING ON HIS LEFT THUMB.

THE EMPLOYEE WAS ATTEMPTING TO ADJUST THE HEIGHTOF A BAG SADDLE. HE INADVERTENTLY BUMPED THE AIRPNEUMATIC SWITCH CAUSING THE BAG SADDLE TO GO DOWN AND PINCHING HIS THUMB.

WHILE ENTERING A RAIL CAR TO BE CLEANED, EMPLOYEE IMPALED A PIECE OF METAL INTO HIS LEFT FOREARM.

EMPLOYEE WAS CLEANING OPEN TOP CARS, BARRING CHUNKS OUT OF HT ECAR WHEN THE BAR BOUNCED BACK HITTING RIGHT SIDE OF MOUTH CAUSING ATOOTH TO BE CHIPPED.

EE WAS TAKING CHUNKS OF DIRT OFF 4A. HE BENT OVER AND STARTED ROLLING A CHUNK OFF BELT AND FELT SOMETHING PULL IN GROIN AREA.

EE WAS STACKING BOXES ON A PALLET. AS HE TURNED AROUND. THE TIRE OF THE FORKLIFT HIT HIS RIGHT FOOT AND WHILE ATTEMPTING TO GET OUT OF THE WAY HIS FOOT WAS CAUGHT UNDER THE TIRE, CAUSING HIS A NKLE TO BE BROKEN.

BEGINNING TO WORK ON MILL STRUCK WITH HEART ATTACK

REMOVING WHEEL PLANETARY FROM TEREX LOADER. BROKEN BONE ON TIP OF LEFT MIDDLE FINGER.

CLIMBING ON LOADER, FT SLIPPED FROM RUNG OF LADDER FELL TO GROUND CAUSING L SHOULDER TO DISLOCATED

EMPLOYEE WAS IN A MAN LIFT CAGE ON A FORKLIFT AND WAS ATTEMPTING TO GET A GEAR BOX AND MOTOR UP TO THE HEAD PULLEY OF THE NEW PD BELT CONVEYOR;GEAR BOX AND MOTOR WERE BEING CHAINED TO THE SIDE OF THE MAN LIFT CAGE.THE CHAIN WAS REMOVED FROMTHE FORKLIFT CAUSING THE MAN LIFT CAGE TO FALL OVER.EMPLOYEE JUMPED FREE FALLING ABOUT 7 FEET.

EMPLOYEE WAS REPLACING AN INSPECTION DOOR ON A MILL, HE SLIPPED AND FELL 8 FEET TO THE FLOOR BREAKING HIS RIGHT WRIST AND BRUISING HIS RIGHT HIP.

AMERICAN COLLOID EMPLOYEES WERE PULLING RAIL CARS ON PLANT RAIL TRACK WITH RETURN 1 1/8 CABLE BEING POWERED BY CABLE MOTOR. CNW RAIL ROAD EMPLOYEE WAS WALKING BY RETURN CABLE. WHEN CABLE POPED UP, UPON STARTING, THE CABLE STRUCK THE CNW EMPLOYEES RIGHT LEG, CAUSING A FRACTURE IN HIS ANKLE, NEEDING SURGICAL REPAIR. THE CNW EMPLOYEE WAS TREATED AND TRANSPORTED BY AMERICAN COLLOID AMB

IT WAS VERY ICY3AND SLIPPERY & BELOW ZERO TEMP. OUTSIDE, SLIPPED WHILE CARRYING A LITE FIXTURE FROM MAINT. SHOP TO FOREMANS PICKUP, INJURING BACK, GROIN AND LEG.

FELL FROM THE S3DE OF THE TEREX FRONT END LOADER WHILE CHECKING THE FUEL, CAUSING THE RIGHT ELBOW TO HAVE A HAIRLINE FRACTURE.

WHILE WORKING,G2T STUNG BY WASP.HE IS ALLERGIC TO BEE/WASP STINGS. (NAME) TREATED STING AND TRANSPORTED TO HOSPITAL.RECEIVED SHOT AND MEDICATION.RELEASED BACK TO REGULAR DUTY.

OXY-ACETYLENE T2RCH CUTTING STEEL SHAFT IN PRECIPITATOR IN PLANT BECAME OVERCOME BY UNKNOWN FUMES FROM CUTTING.HAD PROBLEMS BREATHING GIVEN OXYGEN BY JOB SIDE EMTS AND TRANSPORTED TO HEALTH CE NTER VIA JOB SI7E AMBULANCE.

I WAS WORKING O3 AN OVERHEAD DOOR, STANDING IN A SAFETY CAGE. THEN, I NEEDED TO GET SOME PARTS. CLIMBING DOWN THE LADDER, JUST AS I WAS PUTTING MY FOOT ON THE GROUND, A SCREWDRIVER FELL FROM MY POCKET AND 5ANDED UNDER MY FOOT, CAUSING INJURY TO MY FOOT AND ANKLE.

ROUTINE MAINTENANCE ON GRANNY FEEDER HAD HAND IN FEEDER DOING ADJUSTMENTS AND FEEDER ROTATED CATCHING THUMB EMPLOYEE KNEW THAT HE SHOULD NOT HAVE PUT HAND IN FEEDER UNDER THESE CONDITIONS

WHILE PRYING ON AN OPEN TOP HOPPER WITH A BAR FELT PAIN IN HIS SIDE THE NEXT DAY HE NOTICED A LUMP ABOUT 11.00 AM AND REPORTED IT HE SAW THE DOCTOR ON 7-9-85 HERNIA SURGERY WAS PERFORMED ON 7- 19-85 HE RETURNED TO WORK THE FOLLOWING MONDAY 7-2285 ON RESTRICTED

I.NAME WAS HANGING 3IN CONDUIT ON SIDE OF 2A BELT COVER AT GROUND LEEL WHILE LOOKING UP & HANDING CONDUIT TO HELPER HE STEPPED ON PC OF STEEL & FELL DOWN HITTING HIS KNEE ON GROUND

CUTTING PIEC OF CHANNEL IRON AND PIECE FELL 3\ STRIKING EMPL FOOT ANDPENETRATING BEHIND STEEL TOE PROTECTOR IN BOOT.

EMPLOYEE WAS DISLODGING CHUNK OF BENTONITE FROM ELEVATOR WHEN SHOVEL HE WAS USING WAS CAUGHT BY ELEVATOR BUCKET. CAUSING HANDLE OF SHOVEL TO STRIKE EMPLOYEE IN JAW, BREAKING TWO TEETH.

EMP NEEDED TO ADJUST BAG WEIGHT ON PACKER HE WAS ADJSUTING SADDLE WHEN HE LEANED OVER AND ACCIDENTLY HIT THE AUTOMATIC KICKOFF SWITCH EMP HAD GRABBED SADDLE SUPPORT WHEN SADDLE ITSELF CAME DOW AND CAUGHT THUMB BETWEEN SADDLE SUPPORT AND SADDLE

WHILE LEAVING WORK AREA, EE CAUGHT HEEL OF BOOT ON CATWALK & FELL FORWARD DOWN STEPS. EE CAUGHT WRIST BETWEEN 2 STEPS.

CLEANING PIPET REMOVING FILLING DEVICE ON END OF PIPET WHEN GLASS BROKE CUT FINGER AND PALM OF LEFT HAND STITCHES REQUIRED