JEFFERSON BARRACKS (CS-71) Metal/Non-Metal

Employee alleges EE was grinding and sealing some material and some rust went into EE's left eye.

Employee alleges was climbing down from excavator and sprained left foot.

Employee alleges they were driving a man lift and they hit a rock in the road and they came down hard on their left knee in the lift.

Employee noticed irritation in right eye and associated it with grinding metal the previous day. Waited 1.5 days to notify management at which point EE was sent for medical on 12/15, foreign object removed from eye. Employee was wearing prescription glasses during grinding instead of Company supplied goggles.

Employee was cleaning up material at the base of the scalping screen due to spillage. Another employee was on top of loose material on top the screen to dislodge (approx 35-50 lb) rock. That rock fell, hit the guard, then dropped down about 4" onto employee's right shoulder.

Employee was using a Stihl chainsaw clearing trees. Chainsaw kicked and hit EE's left thigh causing wound/abrasion.

Employee was lifting right leg to climb ladder onto 992K CAT LOADER, EE felt a pull in the right abdomen area. Didn't think much of it, therefore it was not reported that day. That evening while trying to sleep, sharp pain in the lower abdomen/groin area kept EE awake. Reported on 9/23, went to Dr and EE has an Incisional hernia, requiring surgery.

Employee was pulling on gate to change product flow in crusher finishing tower, put left hand in inappropriate area causing pinching laceration on left hand, ring/middle finger.

Employee was attempting to close a misaligned latch on a utility bed tool box with both hands when ee heard a pop in left shoulder.

Employee was using a magnetic drill when the bit broke, causing the mag drill to spin loose and smashed employee's right thumb. INJURY BECAME REPORTABLE ON 5/30/17 WHEN EMPLOYEE WENT BACK TO DR AND NEW XRAYS SHOW A BREAK - RESTRICTIONS BEGAN ON 5/30/17.

Employee was using a walk behind bobcat to clean up spillage under conveyor structure. After filling bucket employee lifted bucket with controls, causing the back end of the machine to rise pinching left hand between the controls and the conveyor structure. Pinching caused laceration and abrasion.

Employee has been diagnosed with carpal tunnel in both hands. Employee does a lot with EE's hands, loading blast holes, connecting detonators, shoveling, operating skid loaders and general plant maintenance. Scheduled surgery on 3 28 16. ****THIS REPLACES SUBMISSION # 2243074 FROM 03/18/16****

Employee started to climb the ladder on his front-end loader when he felt a pain in his left shoulder.

Employee was holding a level on a piece of 3/4" rubber belting while co-worker used a box cutter. Box cutter slipped out of belting causing it to strike employee in the top of wrist causing laceration.

Employee was attempting to exit a scissor-manlift, grabbed the handrails above with both hands lifting body weight and swinging out of the machine. Employee heard a pop and had pain in the top of his right shoulder.

Employee lifting 5 gal grease bucket for the rock drill. Lifting with his left arm to place into cabinet on drill and felt pain in his left shoulder.

Employee was shoveling while cleaning up under the conveyor belt when he felt pain in his low back.

While pressure washing machine, water splashed back onto face and safety glasses. The following day @ shift close employee reported something in eye from day before. Employee was sent to the eye clinic where they washed his eye out and gave him eye drops. MSHA SITE DOWN 10/24 DUE TO MAINTENANCE said to try again today 10/27/14 for reporting.

unloading rocks out of primary housing with a platform hooked to Linkbelt. platform hung up on one end, employee stepped on platform, held the cables and tried to wiggle it free, the platform broke free causing a jerking motion. FIRST WORKDAY WITH RESTRICTIONS 7/07/14

Employee was working on a Needle Scaler and was cutting the needles with a cut off wheel. The cut off wheel grabbed and jerked causing a laceration to the employee's (L) forefinger.

Employee was helping to move a gate in a chute under construction. Employee was pushing down on the gate handle with his rt hand. When the gate handle moved downward the employee lost his balance, grabbing the corner of the chute with his left hand to catch himself, inadvertently causing his ring and middle finger to become pinched by the moving gate, causing lacerations.

EMPLOYEE WAS LIFTING AND ROLLING ONE END OF AN OAK TIMBER OFF OF A LARGE CONCRETE BLOCK WHEN HE FELT A PULLING IN HIS RIGHT UPPER ARM.

Employee was resetting the cone at the crusher with a sledge hammer when he experienced pain in his right shoulder. NOTE: PER MSHA INSPECTOR A 7000-1 WAS NOT NEEDED AT THE TIME OF HIS FIRST DOCTOR VISIT OF 1/04/12. THE EMPLOYEE HAS SINCE BEEN PUT ON RESTRICTIONS STARTING 04/05/2012.

Employee was using a hand grinder with a 4" cutoff wheel to cut an opening on an electrical box when the grinding wheel caught a corner, broke apart, and kicked the grinder back, striking the employee in the left hand, just below the base of his pinky finger causing a laceration.

Employee was working in the primary feeder hopper. He was standing on built up material in the hopper, clamping a piece of belting up so access to the rotor was open. He turned to climb down and his foot slipped, causing him to fall sideways about 2 ft into the bottom of the feeder trough, impacting his right shoulder.

Employee was walking on the grizzly bars inside the feeder hopper to enter the impactor housing to set up wire feed welder on hammers. Employee's foot slipped off top of bars and slipped in between causing top of foot to over extend.

Employee was welding and had a steel hopper raised and secured with nylon straps. One of the straps failed causing the hopper to shift. Something hit the employee on his welding hood or shield causing injury.

employee spent approx 3 hrs working on his knees on steel while doing various handwork while dismantling the primary impactor crusher housing working with a sledgehammer.

employee was checking on unlocked door at accounting office when he fell off the step onto concrete floor.

Employee was kneeling on a catwalk and was using a 3/4" pry bar to scrape build up from the top drum of a gravity take up on the #7 conveyor, while the belt was running. The belt grabbed the bar and pulled it through the drum causing the pry bar to be pulled from his hands causing lacerations from the mushroomed end of the bar.

EMPLOYEE WAS STEPPING OFF A NEWLY INSTALLED WALKWAY AT # 2 CRUSHING PLANT WHEN HE STEPPED WRONG, OVER-EXTENDING HIS RIGHT KNEE BACKWARDS. EMPLOYEE'S KNEE HURT A LITTLE AT THE TIME BUT WAS STIFF AND SORE THE NEXT MORNING.

EMPLOYEE WAS TEST RUNNING A 1710 CUMMINS ENGINE WHEN A FREEZE PLUG BLEW OUT STRIKING HIM ABOVE THE BROW AND SPEWING HOT LIQUID OVER EMPLOYEE'S NECK, HEAD AND ARMS.

Employee was helping remove a hoist cylinder from a 980G cat loader. He was holding the eye of the push rod guiding the cylinder out. When it cleared, it swung forward carrying him with it, knocking him into a support pipe holding the boom arm up. When he let go of the rod eye, the middle and ring fingers of his right hand were cut below the end knuckles.

Employee was coming down the ladder of a 65 ton Euclid haul truck when his right ankle twisted.

Employee was scraping out bucket of front end loader, when his scraper struck some harder, compacted material. This caused his arm to stop short, at which time, he felt a slight twinge in his right elbow. **reported to bussen office 4/30/07**** **1st treatment 4/30/07*****

EMPLOYING WAS THROWING A ROCK OUT THAT HAD JAMMED IN THE CRUSHER. ****1ST DR VISIT ON 12/07/06****** MSHA REPORT NOT FILED AT THE TIME..DID NOT ANTICIPATE THIS TREATMENT.

EMPLOYEE WAS CLIMBING LADDER WITH A PROPANE TANK, HE USED HIS KNEE AS A HELPER TO HOIST TANK TO PLATFORM, FELT PAIN IN RIGHT KNEE. *** 1st DOCTOR VISIT 2/08/06***

employee was turning a piece of 1" plate over to gring off the cutting torch slag when he stepped back on a power cord causing his foot to slip. he lost his lifting momentum causing the weight of the plate to come back at him at which that point he lowered the plate.

Employee was using a 8# sledgehammer to drive a bearing race out of the wheel of a euclid haul truck. The hammer handle caught on a wheel stud causing the hammer to deflect and twisted employee's arm. *****It appears that this employee is going to need more treatment than anticipated.

Employee was operating a bobcat at the crusher doing cleanup when his bucket hit something in the dirt causing him to jar in his seat. *****I realized that a form to MSHA had not been submitted. That is the reason for the delay. Any questions, please contact me.

EMPLOYEE WAS WELDING IMPACT CRUSHER DOOR & KNOCKING OFF SLAG. THAT EVENING HE THOUGHT HE WAS SUFFERING FROM FLASH BURN. HE WENT TO THE EYE CLINIC & HE HAD A PIECE OF FOREIGN OBJECT LODGED IN HIS RT. EYE.

EE WAS WALKING TO HAUL TRUCK TO START SHIFT. WALKED INTO A SMALL GULLEY MADE BY RECENT RAINS AND TWISTED KNEE

EMPLOYEE WAS GREASING THE PLANT. HE LEANED BACK ON THE GUARD RAIL & IT BROKE. HE LOST HIS BALANCE & GRABBED AHOLD OF A PIECE OF ANGLE IRON, CUTTING HIS HAND ON A JAGGED EDGE.

EE WAS WORKING ON WHEEL CALIPERS WITH SLEDGEHAMMER PICKED UP A PRY IRON TO USE AND FELT A PAIN IN HIS RIGHT SHOULDER.

EMPLOYEE WAS BEING LOADED WITH SHOT ROCK BY A FRONT END LOADER. THE LOADER OPERATOR DUMPED THE ROCK INTO THE TRUCK HARD CAUSING THE TRUCK TO SHAKE VIOLENTLY.

EMPLOYEE WAS COMING DOWN THE LADDER OF HIS FRONT END LOADER WHEN HE MISSED THE STEP CAUSING HIM TO HOLD MOST OF HIS WEIGHT WITH HIS ARMS HOLDING ONTO THE HAND RAILS.

EE WAS AT THE CRUSHING PLANT PICKING UP SCRAP PIECES OF PLYWOOD. HE PICKED HIS GLOVES UP AND PUT THEM ON, WHEN HE FELT A STINGING AS IF SOMETHING BIT HIM.

EE WAS IN HIS HAUL TRUCK WAITING TO BE LOADED BY PIT LOADER. THE LOADER DUMPED A BUCKET INTO THE BED AND WHEN HE STARTED BACKING UP THE LOADER HIT HIS TRUCK BED WITH HIS BUCKET, CAUSING THE TR UCK TO ROCK BACK AND FORTH.

EMPLOYEE COMPLETED FUELING HIS HAUL TRUCK. HE CLIMBED UP THE TRUCK TIRE INSTEAD OF THE LADDER. THE TIRE WAS MUDDY CAUSING HIM TO SLIP HITTING HIS KNEE ON THE TIRE.

EE WAS OPERATING FRONT END LOADER ON FROZEN GROUND, CLAIMING THAT EXCESSIVE BOUNCING CAUSED BACK TO ACHE.

EMPLOYEE WAS MAKING ROUNDS CHECKING GATE LOCKS. HE WENT TO GET OUT OF HIS TRUCK THINKING IT WAS IN PARK, INSTEAD IT WAS IN REVERSE. HE WAS KNOCKED TO THE GROUND BY THE DOOR, HITTING HIS HEAD O N THE GROUND, BRUISING HIS RIBS AND HIPS.

EMPLOYEE WAS PUSHING A GRIZZLY BAR WITH HIS BODY OFF THE BED OF HIS PICKUP TRUCK, WORKING IT BACK AND FORTH WHEN HE FELT SOMETHING PULL IN HIS UPPER THIGH AND GROIN.

EE WAS UNCLOGGING CONE CRUSHER. HE STEPPED BACK ON THE WALK WHICH WAS PILED WITH DEBRIS OUT OF THE CRUSHER WHEN HE MISSTEPPED, FALLING OFF WALK DOWN ONTO SAFETY GUARD OVER THE TOP OF THE PIT L ANDING ON HIS FEET. HE THEN SLID DOWN THE GUARD FALLING TO THE GROUND BELOW APPROX. 4'

EE WAS PULLING A 50 LB. BAG OF ANFO FROM PICKUP BED. FELT POPPING IN HIS ARM.

EMPLOYEE WAS EXITING WABCO HAUL TRUCK CAB WHEN HE TRIPPED ON LEDGE. INSTEAD OF FALLING HEAD FIRST, HE JUMPED FROM THE PLATFORM, LANDING ON HIS LEFT HEEL.

EMPLOYEE SLIPPED IN MUD ON GROUND LEVEL AT THE BASE OF STAIRS FALLING ONTO METAL STEPS.

EE HAS BEEN EXPERIENCING PAIN IN BOTH SHOULDERS. EE BELIEVES IT IS FROM USING A SLEDGE HAMMER AS WELL AS THE GRINDER.

EE WAS GOING TO GET TOOLS WHEN HE JUMPED A WATER PUDDLE. THE GENIE MANLIFT BOOM STRUCK HIM IN THE HEAD WHEN HE JUMPED, CAUSING LACERATION ON THE FOREHEAD.

EMPLOYEE WAS STANDING ON A LARGE ROCK FLAGGING THE FRONTEND LOADER TO BUILD A RAMP FOR THE ROCK DRILL, WHEN THE ROCK HE WAS STANDING ON WAS HIT WITH THE TIRE OF THE MACHINE, CAUSING THE EMPLOY EE TO CATAPULT APPROX. 8' IN THE AIR. HE SUSTAINED A BROKEN COLLAR BONE, BROKEN RIB AND BRUISED LUNG.

EMPLOYEE WAS BACKING UP ON STOCKPILE WITH HIS WABCO HAULTRUCK TO DUMP A LOAD. THE PILE GAVE WAY CAUSING THE TRUCK TO GO OVER BACKWARD APPROX 25-30' DOWN.

EE WAS LIFTING A CHAIN TO HOOK ONTO FRONT-END LOADER TO PULL HIS HAUL TRUCK OUT OF MUD. FELT PAIN IN ABDOMEN.

EE WAS TALKING ON THE TELEPHONE WHEN AN ELECTRICAL SHOCK CAME THROUGH THE PHONE AND SHOCKED HER IN HER EAR.

EE WAS GETTING UP INTO A HAUL TRUCK THAT HE NORMALLY DOES NOT DRIVE. HE REACHED FOR THE HAND RAIL & THERE WAS NONE THERE. HE LOST HIS BALANCE & AS HE STARTED TO FALL, HE SHIFTED HIS WEIGHT SO HE COULD GRAB HOLD WITH HIS OTHER HAND. HE FELT PAIN IN HIS HIP

EE WAS TIGHTENING DRIVE SHAFT BOLTS ON HAUL TRUCK WITH A WRENCH. THE WRENCH SLIPPED HITTING EE IN THE MOUTH.

EE DROPPED A PIECE OF PVC PIPE REACHED DOWN TO PICK IT UP & THE END BOUNCED UP HITTING THE TIP OF HIS FOREFINGER.

EE WAS DRAGING SHAKER BEARING HOUSING ACROSS CATWALK AT CRUSHING PLANT WHEN HE FELT PULLING IN HIS LEFT SHOULDER.

EE GRABBED HANDLE TO OPEN GATE AT THE SCREENING PLANT, PULLED UPWARD FEELING STRAIN IN MIDDLE BACK.

EE STARTED HIS MACHINE FOR THE DAY, AS HE WAS CLIMBING DOWN THE LADDER HE FELL FROM THE BOTTOM CHAIN STEP, FALLING APPROX. 2-3'.

EE HAD BEEN KNEELING SERVICING HIS EQUIPMENT. AFTERWARDS NOTICING PAIN IN RIGHT KNEE & SWELLING. [REPORTED TO OFFICE ON 8/6/97]

EMPLOYEE WAS SPRAYING OUT WINDOW AIR CONDITOINER WITH WATER HOSE. HE WAS HOLDING BLADE WITH LEFT HAND WHEN THE WATER PRESSURE TURNED THE BLADE HITTING HIS LEFT RING FINGER AND LITTLE FINGER.

EE WAS RUNNING JUMPER CABLES FROM BATTERY OF HAUL TRUCK TO HIS FRONT END LOADER, WHEN HE PLUGGED THE CABLE INTO LOADER THE BATTERY CAPS ON THE HAUL TRUCK BATTERY POPPED OFF SPEWING ACID OVER E E. THE HAUL TRUCK DRIVER INCORRECTLY HOOKED THE CABLES ONTO HIS TRUCK.

EE WAS WALKING INTO THE OFFICE WHEN HIS LEFT KNEE WENT OUT ON HIM CAUSING HIM TO FALL AND HIT HIS HEAD ON THE ASPHALT.

EE WAS LIFTING A CRUSHER SCREEN AT THE PLANT WITH 2 FELLOW WORKERS WHEN HE FELT A PAIN IN LOWER BACK.

EE WAS CARRYING A FIVE GALLON BUCKET OF OIL FOR HIS CRANE. HE LIFTED IT UP TO THE TAILGATE OF HIS PICK UP TRUCK. SEVERE PAIN IN HIS BACK.

EE JUMPED DOWN OFF GETMAN MANLIFT (APPROX. 2-1/2') AND HURT HIS ANKLE/FOOT.

EE WAS TRYING TO BEND A PIECE OF METAL ON THE UNDERSIDE OF THE STREET SWEEPER WITH A PIECE OF 4 X 4 LUMBER. DURING MID SWING THE 4 X 4 CAUGHT ONA HOSE THAT WAS HANGING DOWN STOPPING HIS SWI;NG , JARRING HIS SHOULDER.

EE WAS CLIMBING LADDER ON FRONT END LOADER TO TALK TO THE OPERATOR WHEN HE HIT HIS LEFT KNEE ON THE LADDER RUNG ON THE WAY UP.

EE WAS WORKING ON HIS TAMROCK DRILL, REPLACING THE DRILL STEEL. HE LIFTED ONE END OF THE STEEL FELT A PAIN IN HIS LOWER BACK.

EE WAS CHANING THE FLUSH HEAD FROM THE ATLAS COPCO ROCK DRILL WHEN HE DROPPED IT HE TREID TO CATCH IT WITH HIS LEFT HAND WHEN HE SMASHED HIS FOREFINGER BETWEEN THE FLUSH HEAD AND THE GROUND.

EMPLOYEE WAS WALKING THROUGH THE MAINTENANCE SHOP WHEN HE STUMBLED OVER A TRAILER TONGUE THAT WAS LYING ON THE FLOOR.

EE WAS USING A METAL HAMMER TO HAMMER A STEEL STEERING PIN FROM A EUCLID HAUL TRUCK. EE HAD BEEN WEARING SAFETY GOGGLES AND REMOVED THEM FOR A BRIEF MOMENT DUE TO SWEAT RUNNING INTO HIS EYES. STARTED TO HAMMER AGAIN WHEN A PIECE OF METAL LODGED IN RT EYE.

EE WAS PRYING ON THE TRACKS OF THE GARDNER DENVER ROCK DRILL AND FELT A PAIN IN HIS RT SHOULDER.

EMPLOYEE WAS CLIMBING UP LADDER ONTO THE WATER TRUCK WHEN HE FELT A PAIN DESCRIBED AS A "CHARLEY HORSE" IN RIGHT HIP.

EE WAS WORKING ON A PIECE OF EQUIPMENT WHEN HE DROPPED THE WRENCH HE WAS WORKING WITH ON TOP OF HIS RIGHT FOOT, JUST BEHIND THE PLATE ON HIS STEEL TOED BOOTS.

EE WAS MOVING A PIECE OF IRON WHEN HE STEPPED BACKWARD BUMPING HIS LEFT ELBOW INTO ANOTHER PIECE OF IRON.

EMPLOYEE WAS USING A GREASE GUN OVER AT THE CRUSHING PLANT WHEN HE FELT PAIN IN HIS RT WRIST WHILE PUMPING THE GUN

EMPLOYEE WAS AT THE CRUSHING PLANT LOADING HIS TRUCK WHEN A PIECE OF LIMESTONE DUST EMBEDDED IN HIS LEFT EYE

EMPLOYEE WAS GRINDING ON A SPREADER BAR, PIECE OF METAL LODGED IN RIGHT EYE. (EMPLOYEE WAS WEARING PROTECTION).

EE HAS NUMBNESS IN BOTH HANDS. POSSIBLE CARPAL TUNNEL SYNDROME. EE MAIN JOB ACTIVITY IS SHOVELING AT THE CRUSHING PLANT.

EMPLOYEE ST ARTED SHOVELING FOR THE DAY SAID HE FELT A PULLING & TWISTING IN THE MIDDLE OF HIS LOWER BACK

EE WAS PARKING HIS TRUCK AFTER HIS SHIFT HE WENT INTO THE UNDERGROUND PARKING WHERE THE LIGHTS WERE NOT ON. HE CONTINUED BACK TO PARKING AREA AND STARTED TO PARK HIS TRUCK HE LOST HIS DIRECTIO N AND DROPPED THE FRONT OF THE HAUL TRUCK OFF APPROX. 5 FT DOWN.

EMPLOYEE WAS GRINDING ON A PIECE OF METAL WITH GRINDER PIECE OF METAL LODGED IN EMPLOYEES LEFT EYE

EMPLOYEE WAS SCRAPING CAKED LIMESTONE FROM SHOOT WHEN A CHUNK BROKE LOOSE FALLING DOWN ONTO BOARDWALK ON WHICH THE EMPLOYEES WERE STANDING CUSING EMPLOYEE TO FALL APPROX 4FT TO GROUND

EMPLOYEE WAS GRINDING ON THE HIGHLIFT BUCKET WHEN A PIECE OF FOREIGN OBJECT EMBEDDED IN RIGHT EYE

WALKING ON INCLINE WITH BAG OF ANFO CATCHING SELF FROM FALLING FELT SOMETHING PULL IN LOWER BACK

EMPLOYEE WAS PULLING BIN GATE HANDLE TO LOAD HIS DUMP TRUCK, HE FAILED TO RELEASE THE HANDLE ON THE BIN GATE (PUTTING STRAIN ON LEFT ARM AND LEFT SID EOF NECK AND HEAD AREA.)

EMPL WAS LOADING ROCKS ONTO HAUL TRUCK WHEN ROCK ROLLED OUT OF BUCKET & ONTO HOOD OF TRUCK. EMPL WHILE PUSHING ROCK OFF TRUCK HOOD FELT PAIN IN LOWER BACK.

EMPLOYEE WAS LIFTING STEEL DOOR ON ELECTRIC BOX,FELT PAIN IN HIS LEFT SHOULDER.

CARPEL TUNNEL SYNDROME OPER MACHINERY

EMPL WAS WORKING UNDERNEATH HAUL TRUCK WHEN FOREIGN OBJECT FELL INTO RIGHT EYE.

EMPL UNHOOKING BATTERY JUMPER CABLES FROM FRONT-END LOADER WHICH HE HAD JUST JUMP-STARTED.BATTERY BLEW UP IN HIS FACE.

EMPL WAS CUTTING LOCK NUT OFF TAMROCK RILL WITH DYE GRINDER DISC ON GRINDER EXPLODED HITTING EMPL IN RIGHT SIDE ALONG JAW LINE.

EE WAS USING A METAL HAND GRINDER WORKING ON CRANE BOOM FOREIGN OBJECT IN LEFT EYE.

EMPLOYEE WAS ON THE BACK OF HIS FRONTEND LOADER SERVICING THE HEATER, HE JUMPED OFF THE BACK OF THE MACHINE, AFTER A FEW HOURS HE NOTICED PAIN IN HIS BACK.

EMPLOYEE WAS PULLING ON A RATCHET TO TIGHTEN A NUT ON CRANE, WHEN HE GOT HOME THAT NIGHT HE NOTIECED A KNOT IN LOWER RIGHT SIDE OF HIS ABDOMEN.

EMPLOYEE WAS STANDING ON AIR PIPE ON THE GETMAN (BOOMER), WENT TO STEP OVER TO THE OTHER MACHINE (WATER TRUCK) WHEN THE PIPE ON WHICH HE WAS STANDING BROKE, HOLDING ONTO LADDER WITH LEFT ARM H E SWUNG INTO THE WATER TRUCK WITH LEFT SIDE OF BODY.

EMPL LOADING BARGE WINCH GEAR ONTO PARTS TRUCK WHEN IN ROLLED AND SMASHED FOREFINGER ON RIGHT HAND.

DRILLING PINS OUT OF CRANE PC OF METAL LODGED IN R EYE

EMPLOYEE WAS SLEDGE HAMMERING ON METAL PIN OFF OF CRANE, PIECE OF PAINT FROM PIN LODGED IN RIGHT EYE.

EMPLOYEE WAS WELDING AND GRINDING ON STORAGE BIN, PIECE OF STEEL EMBEDDED IN RIGHT EYE.

EMP WAS ATTEMPTING A LEFT TURN WITH HIS LOADED HAUL TRUCK HE MISSED TURN CAUSING HIS TRUCK TO SLIDE DOWN A 15 T EMBANKMENT TURNING TRUCK OVER RIGHT SIDE.

EMPLOYEE WAS REPARING FLOOR OF BARGE HIS FOOT SLIPPED FROM PIECE OF IRON ON WHICH HE WAS STANDING CAUSING HIM TO FALL HITTING RT SIDE OF RIB AREA ON PIECE OF IRON

EMPLOYEE WAS STEPPING DOWN OFF WATER TRUCK RT FOOT SLIPPED OFF BOTTOM STEP EMPLOYEE TWISTED BACK WHILE REGAINING BALANCE

EMPLOYEE WAS GREASING FRONT END LOADER, WENT TO WALK AROUND MACHINE AND BUMPED HIS SHOULDER ON MIRROR CAUSING HIM TO LOOSE HIS BALANCE. HE FELL FROM LOADER HOLDING ONTO SAFETY RAIL CAUSING HI M TO JERK MUSCLE IN RIGHT ARM.

EMPLOYEE WAS WELDING IN CRUSHER, A PIECE OFWELDING SLAG LODGED IN RIGHT EYE.

EMPLOYEE WAS WA5KING AROUND FRONT OF ROCK DRILL, SLIPPED IN MUD FALLING TO HANDS AND KNEES.

EMPLOYEE WAS HO2KING UP CRANE CABLES ONTO BARGE LIDS, FINGER PINCHED BETWEEN BARGE LID AND CABLE SHACKLE.

EMPLOYEE WAS JU4PING DOWN BETWEEN BARGES TO CHANGE CABLE ON SAND BARGE HIT HIS RT.ELBOW ON BARGE RAILING

EMPLOYEE WAS CA9RYING A WATERING HOSE, TRIPPED AND FELL LANDING ON HIS RIGHT WRIST.

EMPLOYEE WAS US3NG AIR COMPRESSOR BLOWING SLAG FROM WELD ON HI-LOFT,PIECE OF METAL LODGED IN EYE.

EMPL DUMPING LO5D ONTO BARGE WHEN FOREIGN OBJECT FLEW INTO RIGHT EYE.

EMPLOYEE WAS BA7KING HIS TRUCK UP TO THE END OF THE STOCKPILE TO DUMP HIS LOAD ROCK, WHEN HIS TRUCK FELL OFF THE STOCKPILE, APPROX. 30 FT BELOW, LANDING UPSIDE DOWN.

EE WAS CLIMBING3LADDER AT THE CRUSHER WHEN HIS FOOT SLIPPED OFF THE RUNG CAUSING EE TO FALL OFF LADDER LANDING ON TAIL BONE.

EE WAS SHOVELIN1 TO CLEAN OUT THE BED OF HIS TRUCK WHEN A FOREIGN OBJECT FLEW INTO RIGHT EYE.

EMPLOYEE WAS WO9KING ON THE CONE CRUSHER,WHILE PUSHING AGAINST FLYWHEEL WITH HIS BACK HE FELT SOMETHING PULL IN THE BACK OF HIS NECK.

EMPLOYEE WAS CH5NGING BUCKET ON THE CRANE, WHEN HE STEPPED UP ON THE TRACK OF THE CRANE HE LIFTED UP HITTING HIS HEAD ON THE CRANE BOOM.

EMPLOYEE WAS GE7TING OUT OF HIS TRUCK,HE WAS HOLDING ONTO HAND RAIL,WHEN HE WENT TO STEP DOWN FROM HIS TRUCK HE MISSED THE STEP CAUSING HIM TO JERK HIS ARM AND DISLOCATE HIS RIGHT SHOULDER.

EMPLOYEE WENT I3TO OIL SHED TO LOCK IT UP FOR THE NIGHT & TRIPPED ON FUEL HOSE LAYING ON FLOOR WHEN HE TRIPPED HE STOPPED HIMSELF FROM FALLING BY GRABBING ONTO DOOR & WHEN HE DID HE JHAMMED H S LITTLE FINGER3ON LEFT HAND

EMPLOYEE WAS WA5KING OVER BUNDLES OF PIPE IN BARGE WHEN TWO BUNDLES OF PIPE ROLLED TOGETHER ON HIS RT FOOT

EMPLOYEE WAS ON3HIS WAY TO CLEAN OUT PAN FEEDER ON CRUSHING PLANT HE SLIPPED AND FELL DOWN INTO THE PAN FEEDER ON CRUSHER HIS RT WAS BRUISED ALSO SHOULDER HIP KNEE AND RIB CAGE

EMP WAS PUTTING3EXHAUST MANIFOLD ON EUCLID TRUCK LOST HIS FOOTING FELL APPROX 4 TO 5 FT MANIFOLD FELL ON H IS LEFT SIDE AND HE HIT HIS HEAD ON CONCRETE FLOOR

EMPLOYEE WAS UN2OOKING PUIPE HOOKS OFF PIPE WHEN THE PIPE SLIPPED & SMASHED HIS FINGER BETWEEN TWO PIECES OF PIPE

EMP WAS HAULING3A LOAD OF LIME UP ON THE STOCKPILE TO DUMP, WHEN THE T RUCK CAUGHT ON FIRE FROM A POSSIBLE BREAK IN ONE OF THE OIL LINES, SQUIRTING OIL ON THE HOT EXHAUST PIPE

EE WAS CHANGING3CABLES ONT HE CRANE HAD TAILLINE CABLE SECURED WITH VISE GRIPS WHEN VISE GRIPS WERE RELEASED THE SPRINGS ON T HE BOOM OF THE CRANE HAD TENSION ON CABLE & WHEN SLACK WENT OUT O F THE CABLE ON3THE BUCKET BROKE RELEASING CABLE WHICH WRAPPED AROUND EES MID-SECTION & PULLED HIM TO THE GROUND.

EMPLOYEE WAS CH5NGING HOSES ON FRONT END LOADER AND SLIPPED OFF AXLE HITTING ELBOW ON FRAME OF LOADER

EMP WAS DOING S2ME SHOVELING DOWN AT CRUSHING PLANT HE SLIPPED IN SOME MUD AND WHEN HE STARTED TO FALL HE TRIED TO CATCH HIMSELF AND HIT HIS RIGHT FOREARM ON AN IRON POST

EMPL CHANGING S7REENS ON SCALPING SCREENS AT CRUSHING PLANT EMPL LIFTED ONE OF THE SCREENS AND FELT PULLIN IN GROIN AREA.NOTE:EMPL HASNT LOST TIME BUT ITS LIKELY EMPL WILL NEED SURGERY.

EMPLOYEE WAS GR5DING ROADS WITH A MOTOR GRADER, WHILE OPERATING THE LEVER WHICH CONTROLS THE BLADES MOVEMENT HE BRUISED THE LEFT PALM OF HIS HAND FROM THE VIBRATION.

EMPLOYEE WAS WORKING ON A TRUCK AND WAS TIGHTENING DOWN THE MOTOR MOUNTS WITH A WRENCH AND FELT SOMETHING PULL IN THE TOP OF HIS RT ARM

EMPLOYEE WAS CARRYING A 5-GALLN CAN OF OIL TO A PIECE OF EQUIPMENT THAT HE WAS SERVICING & FELT A PULLING OR TWISTING IN HIS BACK

EMPLOYEE WAS STANDING ON THE SIDE OF A TRACTOR TRAILER\S TRAILER WHEN HIS FOOT SLIPPED OFF AND HE FELL ON A PIECE OF WOOD ON THE GROUND BELOW.

EMPLOYEE WAS TIGHTENING STERN CABLE ON SAND CRANE WHEN HE FELT A PULLING IN HIS LOWER BACK. EMPLOYEE DIDNT GO TO THE DR OR TO THE HOSPITAL FOR EXAM

EMPLOYEE DUMPED A LOAD OF ROCK INTO HOPPER AND WAS PULLING AWAY WHEN HE FAILED TO LET HIS BED DOWN AND HE HIT THE CONVEYOR WITH HIS RAISED TRUCK BED.

EMPLOYEE WAS WORKING ON A @WABCO DUMP TRUCK AND TOOK THE CENTER HEAD OF TRUCK OUT AND WAS COMONG DOWN @OFF TRUCK WHEN PIECE FELL FROM HANDS DUE TO GREADE ON CENTER HEAD AND ON HANDS AND FE FELL ON EMPLOYEES GREAT TOE RIGHT FOOT.

GETTING OUT OF TRUCK WHEN HE STEPPED ON FIRST STEP TO COME DOWN LADDER,SLIPPED-MUDDY SHOES-FALLING 7-8\ TO THE GROUND.

EMPLOYEE WAS STANDING ON A TRAILER DIRECTING PIPE FOR UNLOADING WHEN THE STRAP HOLDING THE PIPE TOGETHER BROKE PIPE FELL AND HIT HIM IN THE RIGHT THIGH

SHOVELING AND STEPPED BACK WHEN RIGHT FOOT WENT INTO HOLE TWISTING HIS BACK.