Oak Grove Preparation Plant: 1,151 citaciones de la MSHA Coal

IE was completing a pre-op on the D6 dozer when EE slipped and fell to the ground. When the employee hit the ground, EE hit their left wrist.

IE was climbing off a dozer when they slipped and strained their back.

IE was assisting in removing a poly deck screen when they hit a wrist on a beam.

IE was walking to a pump on the 1st floor of the prep plant when IE stepped into a drain hole that the grating had moved from. The IE hit knee on the edge of the concrete.

IE was carrying flume screens down steps when IE missed the bottom step and fell to knees. IE did not seek medical attention until 5-25-21.

IE was switching from the D9N dozer to the D9L dozer when EE felt a pain in their left shoulder. IE was taken to OHC and is set up to follow up. IE has not returned to work.

A D-10 Dozer was discovered on fire at the Prep Plant. The dozer could not be extinguished by employees at the Prep Plant. The local fire department came and extinguished the fire. There were no injuries. MSHA was notified via the hotline and they also investigated the fire.

IE had just cleaned the scalping screen and was coming down the steps. IE slipped down the last 4 stairs and fell. IE was taken to be checked out.

IE was cleaning the material from the top of the scalping screen. IE was swinging a pick and an angle due to the chute of the reclaim belt to dig the material from the screen and IE felt a sharp pain in lower back. IE wanted to be taken to checked out.

IE was changing rollers on a beltline when EE felt a pain in EE's lower and middle back. IE did not request attention until the end of EE's shift.

IE was running a rock truck. IE went over a rut and bounced up hitting head on the top of the truck. IE finished shift and waited until 3-31-2020 to be checked out by a Dr.

IE was changing an underflow pump when IE stepped in a hole. The IE then fell and twisted knee. IE finished shift then decided to seek medical attention.

A contract employee was helping set-up a winder. A second contract employee was in an elevated position when a metal plate slipped from EE's hand. The plate struck the injured employee on the shoulder. The following were not a factor: rules, regs., systems, equipment, PPE. Attitude may have been a factor. Did not lose time until September 4, 2019.

IE was turning a splash guard on the 6th floor of the Concord prep Plant. As EE was pushing the splash guard EE felt a pain in EE's left shoulder. IE missed no work until 8/16/19. After IE visited the Dr on 8/16/19 for EE's shoulder pain, the Dr took EE off of work but found no damage in EE's shoulder. Possibly a strained muscle that needed to heal.

IE was trying to break some bolts loose with ratchet. As IE was straining IE felt pain in left shoulder. IE was taken to the Dr & was taken off of work for 1 week.

IE was removing a piece of metal out of a chute. As IE pushed the piece of metal off of the side of the belt, IE felt something pull in IE's left shoulder. Still waiting on the Dr's report to see what is wrong with IE's shoulder.

While replacing filter sector, the sector slide back from its resting spot. Employee attempted to grab it but while doing so felt a pull and pop in right shoulder.

EE was walk down stairs from 10th to 9th floor. When stepping onto the landing of 9th floor EE "rolled" ankle because of uneven grating.

Injured was washing under the coal storage silo when the hose separated. The injured ran to get away from hose but struck head on a piece of steel. Injured suffered a strain of muscle, fascia and tendon at neck level. Injured became reportable on 7/18/2016.

Injured was monitoring the thermal dryer when a hot spot developed. The injured called to the control room to turn the fan down. Injured thought the fan had turned off and opened the access door. When the door was opened, the injured suffered burns to the face, neck and wrist as the fan was still running at a lower speed.

Carrying five gallon buckets of coal samples down stairway to elevator.

Injured was changing screen panel in vibrating screen. The vibrating screen was de-energized and locked out. As injured exited the screen deck the injured pulled on the drive mechanism vee belt. This caused the sheave wheel to rotate pulling his right hand between the belt and sheave wheel resulting in a laceration to the palm and fracture of the 5th finger .

injured was reinstalling a guard the had been removed to allow cleaning under the overland belt line. injured lifted the guard up and felt tear in his right shoulder. belt was off and locked out.

Employee was in squatting position and knee gave out when standing up.

Employee was walking across Sump Walkway and tripped cutting his knee.

While walking down stairs employee misjudged the distance of the last step and fell. Employee has an Inguinal Hernia. Medical evidence shows this may be a re-occurrence of a non work related previous injury.

Injured and coworker were replacing a pump. there was not enough clearance for the pump to slide over the pump well hand rail. The new pump became caught on the hand rail. Injured lifted up the pump. The pump slid across the hand rail catching injured' s left thumb between the pump base and hand rail resulting in a severe laceration. Hospital personnel amputated the thumb.

Employee was dismounting haul truck on the off operator side (passenger) when he lost his balance when he missed reaching for the handrail. No three point contact was used. The employee then fell to the ground (Approx. six feet) landing on his left foot causing a broken bone in his foot.

EE was shoveling concrete. He reached too far with a shovel & felt a tingly feeling down his left leg. His supervisor placed him on light duty for 3 days. On 7/14/11, EE was taken for medical treatment. He was released with restrictions for seven days. EE is now on light duty at the Concord mine site. He will return to full duty 7/21/11 per doctors orders.

Moving material on a 4 wheel cart. Material shifted when cart caster was rolled into opening in existing grating causing cart to shift and strike EE in the face. He received laceration above left eye and left nostril the injury required stitches. EE is release to working modified duty.

Wire way was lowered to the floor and the wire way was in one piece with a flanged connection. EE was taking the connection apart to get it off the floor. When he took the last bolt out the forward piece hit the floor. EE thought that it wasn't as heavy as it was and smashed his finger between the flange and the floor.

Removing a piece of conduit from the building, employee grabbed the conduit and the sharp edge cut the palm of his right hand.

Injured suffered heat exhaustion while working on a pump.

Fractured rib removing conduit.

injured and co-worker were using a pipe wrench to free a pump sheave wheel. the sheave wheel suddenly free up causing injured to pinch his right ring finger between the sheaved wheel and the pipe wrench.

INJURED EMPLOYEE WAS CHANGING A DRIVE BELT ON #8 WEMCO DRYER. INJURED WAS ATTEMPTING TO ROLL THE DRIVE BELT ONTO THE PULLEY. THE PULLEY WAS BEING TURNED BY HAND. THE PULLY TURNED, CATCHING INJURED LEFT LITTLE FINGER IN A PINCH POINT BETWEEN THE HOUSING AND THE PULLEY RESULTING IN AMPUTATION OF END OF LITLE FINGER.

INJURED WAS STANDING ON PUMP MOTOR ATTEMPTING TO HANG COME-A-LONGS IN TROLLEY. INJURED FOOT SLIPPED CAUSING HIM TO FALL AND STRIKE A PROTRUDING GREASE FITTING ON THE PUMP MOTOR.

A subcontractor's employee was improperly crossing bracing when he lost his grip and fell. He suffered a fracture in his lower left leg.

Employee claimed back pain next day after using chain falls on 10-28-04.

INJURED WAS IN THE ELEVATOR ON THE 1ST FLOOR OF THE PLANT. HE WAS ATTEMPTING TO CLOSE THE OUTER DOOR. HE WAS PULLING DOWN ON THE STRAP WITH BOTH HANDS. HE LEANED TOWARD THE DOOR AS HE PULLED & WHEN THE TWO PARTS OF THE DOOR CAME TOGETHER HE GOT HIS MIDDLE, RING & LITTLE FINGER ON HIS RIGHT HAND BETWEEN THE DOOR HALVES.

INJURED WAS ATTEMPTING TO PULL A 5 GALLON BUCKET OUT OF MUD. HE PULLED ON THE HANDLE, THE HANDLE BROKE AWAY FROM THE PLASTIC. THE INJURED FELL BACK AND THE HANDLE PULLED THROUGH HIS HAND CAUSI NG A 3/4" CUT BETWEEN HIS THUMB & FOREFINGER. HE WAS NOT WEARING HIS GLOVES. INJURY REQUIRED THREE STITCHES.

INJURED WAS USING A UTILITY KNIFE TO CUT RUBBER GASKET MATERIAL ON A FLAT TABLE IN THE SHOP. HE HAD THE KNIFE IN HIS RIGHT HAND CUTTING TOWARDS HIMSELF. THE KNIFE SLIPPED & HIT HIS LEFT INDEX FINGER, CUTTING IT. HE WAS NOT WEARING GLOVES. CUT REQUIRED TWO STITCHES TO CLOSE.

INJURED WAS STEPPING FROM THE BOTTOM STEP. PUT HIS LEFT FOOT DOWN AND TURNED TO HIS LEFT. HIS FOOT DID NOT PIVOT AND HE FELT PAIN IN HIS LEFT KNEE, AS HE TWISTED.

INJURED WAS INSTALLING A BELT COVER ON #2 DRYER CONVEYOR. HE WAS STANDING ON THE BELT DECKING SLIDING THE COVER INTO PLACE. HE FELT A SHARP PAIN IN HIS KNEE. HE THINKS HE MAY HAVE TWISTED HIS KNEE, LEFT KNEE. NOTE: INJURED HAD SURGERY ON FEB 01, 2001.

INJURED WAS WALKING DOWN THE EAST STEPS BETWEEN THE 4TH & 3RD FLOORS. WHEN HE STEPPED ON THE CONCRETE SLAB THAT IS MIDWAY BETWEEN THE FLOORS HISFEET SLIPPED OUT FROM UNDER HIM AND HE FELL. HE THOUGHT THE FLOOR WAS WET BUT IT WAS COVERED WITH A LAYER OF ICE. HE TRIED TO CATCH HIMSELF WITHHIS ARM. HE FRACTURED HIS RIGHT DISTAL RADIUS.

EE APPLYING EPOXY TO CHUTE, TROWEL-EASE (ALCOHOL BASED) USED TO SMOOTH OUT EPOXY. EE WAS CHUTE APPLYING MATERIAL. WAS DARK IN CHUTE & PORTABLE WORKLIGHT USE. DROPS OF TROWEL-EASE FELL ON WORK LIGHT & IGNITED. EE SUFFERED 2ND DEGREE BURNS ON RT. FOREARM, 2ND DEGREE ON LEFT HAND & NOSE, 1ST DEGREE & 2ND DEGREE ON RIGHT HAND.

INJURED WAS INSPECTING THE INTALLATION OF A GRIZZLY UNIT 141. HE WAS STANDING ON UNIT 150, 34 INCHES ABOVE THE FLOOR. HE REACHED IN UNIT 141 TO GET A PAPER TAG. AS HE REMOVED THE TAG HIS ARM F ROM THE CHUTE HE FELL OFF THE EASTSIDE OF UNIT 150. INVESTIGATION SHOWS HE MAY HAVE HAD HIS FACE IN THE ATMOSPHERE WHICH CAUSED HIM TO FALL.

BARS OUT OF POSITION ON THE THERMAL DRYER BED CAUSED A DEAD SPOT. (NO AIR COMING THROUGH.) COAL LAYED ON THE DEAD SPOT AND CAUGHT ON FIRE. WHEN FEED TO THE DRYER GOT LIGHT A SPARK WAS PULLED U P FROM THE BED & IGNITED THE DUST.

INJURED HAD JUST REPLACED A SHEAVE ON THE #1 REFUSE SCREEN DRIVE. IN AN ATTEMPT TO PUT THE BELT SON TEH HOOKED TO THE LIFTING EYE WITH CHAIN FALLS, AND ATTEMPTED TO PULL THE MOTOR OVER TO GET ENOUGH SLACK TO PUT THE DRIVE BELTS ON. THE LIFTING EYE BROKE WHILE HIS LEFT HAND WAS ON THE SHEAVE. SHEAVE FLEXED ABOUT 6" CUTTING HIS HAND. NOT WEARING GLOVES.

INDIVIDUAL WAS STANDING ON THE #2 REFUSE D&R SCREEN INSTALLING A SCREEN. HE WAS HOLDING UP THE EDGE OF A SCREEN PANEL. HE LOST HISFOOTIN GAN DFELL. WHILE TRYIN GTO CATCH HIS BALANCE WITH ON E HAND THE RIGHT HAND WAS HOLDING THE SCREEN. AS HE FELL, HIS RIGHT HAND & THE SCREEN IMPACTED A HOLD DOWN RAIL.

INJURED WAS CUTTING NUTS OFF THE BOLTS HOLDING ON A REFUSE SCREEN DRIVE MECHANISM. INDIVIDUAL WORKING WITH HIM GOT ABOVE HIM TO GET A 1" AIR IMPACT WRENCH. HE DROPPED A 2 3/4" SOCKET. IT STRUC K THE INJURED ON HIS LEFT HAND, INJURING HIS LEFT RING FINGER.

INJURED WAS ATTEMTPING TO REMOVE A LID FROM A PLASTIC OIL BUCKET. HE WAS USING HIS POCKET KNIFE TO CUT THE TABS. WHILE HOLDING DOWN ON THE BUCKET WITH HIS LEFT HAND, HE PULLED HIS KNIFE UP THR OUGH A TAB TOWARDS HIMSELF. THE KNIFE CUT HIS LEFT ARM JUST ABOVE THE WRIST.

INJURED CLAIMED BILATERIAL CARPAL TUNNEL SYNBDROME IN BOTH HANDS.

INJURED WAS OPERATING THE KOWASAKI MULE. TRAVELING EAST ON PLANT ROAD. TURNED LEFT AT INTERSECTION AND RT FRONT WHEEL CAUGHT A POT HOLE. THE MULE TURNED UP ON ITS SIDE. THE INSIDE MIRROR CAME LOOSE AND MAY HAVESTRUCK INDIVIDUAL ON THE EAR CAUSING A LACERATION.

INJURED WAS REMOVING A 24X 34 METAL DOOR. REMOVED LAST CLIP AND WAS HOLDING DOOR WITH RIGHT HAND. DOOR MOVED BACK TOWARD HIM BENDING HIS THUMB CAUSING INJURY.

QUESTIONABLE FIRE OCCURRED IN CLEAN COAL SILO, AS A RESULT OF HOT MATERIAL FROM DRYER BEING DUMPED IN CLEAN COAL SILO. FIRE WAS EXTINGUISHED IMMEDIATELY.

HOISTING EQUIPMENT WITH A CHAIN HOIST AND THE EQUIPMENT SHIFTED AND HIT THE WORKER IN THE CHEST. HE WAS CAUGHT BETWEEN THE EQUIPMENT AND A PIPE.

INJURED WAS EXITING THE SHOWER, BOTH FEET SLIPPED OUT FROM UNDER HIM. HE LANDED ON HIS BACK AND SHOULDER. FLOOR WAS WET, INDIVIDUAL WAS WALKING AT NORMAL SPEED.

WHILE ADJUSTING A CONVEYOR SKIRTBOARD, SKIRTBOARD TIPPED OVER PINNING EMPLOYEES RIGHT HAND BETWEEN AN IDLER AND THE SKIRTBOARD.

INJURED WAS MOVING FLIGHTS FOR A CONVEYOR ALONG A MONORAIL TROLLEY SYSTEM. INJURED DID NOT NOTICE STOPS AT END OF MONORAIL HAD BEEN REMOVED FOR REPAIR. HE PULLED FLIGHTS OFF END OF MONORAIL. F URING THE FALL OF FLIGHTS, INJURED'S ARM WAS SCRAPED BY MATERIAL.

WHEN EMPLOYEE OPENED AN ELEVATOR DOOR AT THE JOB SITE, A PIECE OF 3X3 ANGLE IRON FELL FROM ABOVE FLOOR. INJURY DESCRIBED AS A CONTUSION; BRUISED AND STRAINED SHOULDER.

WATER FROM A MATERIAL SPILLAGE ON THE DEISTER TABLES ON THE 3RD THIRD FLOOR OF THE PREP PLANT RAN DOWN AN OUTSIDE WALL ONT O A STEEL ANGLE AND INTO THE MASTER CONTROL CENTER ON THE 1ST FIRST F LOOR OF THE PREP PLANT AND ONTO THE TOP OF THE ELECTRICAL CABIENT, IT IS TURN CAUSED A SHORT CIRCUIT AND BEGAN TO ARC CAUSING AN ELECTRICAL FIRE IN THE CABINETS THAT DESTROYED MUCH FOR THE MA

OPERATOR OF DOZER ATTEMPTING TO MOUNT THE MACHINE AFTER REFUELING FOOT SLIPPED OFF THE CAT PAD LEFT LEG WENT BETWEEN THE CAT PAD & THE BLADE ARM RESULTING IN A SCRAPE/ABRASION/BRUISE TO LEFT L EG CAT PAD IS THE DOZER TRACK

EMPLOYEE WAS SETTING PIPE AND HIS HAND WAS CAUGHT BETWEEN THE PIPE AND THE HANDRAIL HE WAS WORKING ON/NEAR. EMPLOYEE'S RIGHT INDEX FINGER WAS BROKEN.

EE HAD FINISHED INSTALLINGA PIECE OF PIPE. HE RAISED UP AND HIT HIS HEAD ON ACONDUIT TRAY. ALTHOUGH THE EE HAD HIS HARD HAT ON , HE "JAMMED" HIS NECK.

EMPLOYEE WAS IN PROCESS OF TIGHTENING BOLTS ON ROTARY BREAKER PLATES. HOLDING A SOCKET IN HIS LEFT HAND TRYING TO START BOLT INTO NUTS AS HE ENERGIZED THE IMPACT WRENCH THE ROLL PIN HOLDING T HE ALLEN WRENCH INTO THE SOCKET BACKED OUT. THIS CAUGHT HIS LEFT PALM LACERATING IT.

INJUR ED WAS R EMOVING A UNDERFLOW PUMP FROM ONE FLOOR TO & T HEN HE HAD HOISTED PUMP UP & SET IT DOWN LEANING ON ANOTHER PUMP BASE HE HAD HIS FOOT UNDER THE PUMP WHEN THE PUMP SLIPPED DOWN TH E BASE CATCHING HIS FOOT BETWEEN THE PUMP & FLOOR

THE INJURED EMPLOYEE WAS ATTEMPTING TO FREE A PLUGGED COAL CHUTE BY STRIKING THE SIDE OF THE CHUTE WITH A SLEDGE HAMMER. AS HE SWUNG THE HAMMER, IT CAUGHT ON A HAWKEYE SENSOR LINE CAUSING HIM TO LOSE HIS BALANCE AND FALL.

95106PERATING FRONT END LOADER WHEN THE ENGINE RAN HOT. EMPL TRIED TO COOL RADIATOR BY SPRAYING COLD WATER ONTO IT. CAUSED RADIATOR CAP TO BLOW OFF ALLOWING HOT WATER AND STEAM TO HIT INJ EMPL 06503EFT FOREARM.

THE INJURED EMPLOYEE WAS MOVING A METAL PLATE, 3/8" X 8' X 10', THAT WAS LAYING ON A STAND. HE WAS SLIDING THE PLATE AROUND BY LIFTING ONE END UP WHEN HIS RING FINGER, LEFT HAND WAS CAUGHT BET WEEN THE STAND AND THE PLATE.

38509NJURED WAS REMOVING A V-BELT GUARD FROM MOTOR DRIVER HE WAS USING.A BOX END WRENCH TO LOOSEN THE NUTS.THE NUTS ROUNDED OFF CAUSING THE WRENCH TO SLIP.THIS CAUSED THE INJURED PERSONS RIGHT 08154 TO STRIKE THE GUARD MOUNTING BRACKET RESULTING IN A FRACTURE TO HIS RIGHT HAND.

38509NJURED EMPLOYEE WAS GOING OUT SIDE DOOR LOCATED NEXT TO #5 FILTER OF PREP PLANT AS HE EXITED THE BUILDING HIS RIGHT FOOT SLIPPED ON SOME MUCK.HIS LEFT FOOT BECAME ENTANGLED AND WAS UNDER 89202ODY BY HIS WEIGHT TRANSFER.THIS RESULTED INA SPRAINED LEFT ANKLE.

EMPLOYEE WAS TURNING CHAIN GUARD TO WELD ON LIFTING LEG.WHEN HE LIFTED CHAIN GUARD HE STRAINED HIS LOWER BACK.

INJURED EMPLOYEE WAS USING PRY BAR TO PRY SLEVE BIN AWAY FROM ELECTRICAL BOX PRY BAR SLIPPED & EMPLOYEE LOST CONTROL & FELL BACKWARDS ON HIS HIP

INJ CLEANING UNDER OVERLAND BELT WITH SHOVEL.THE SHOVEL CAUGHT BETWEEN BOTTOM ROLLER AND BELT CAUSING INJ TO LOSE BALANCE AND FALL AGAINST ALIGHNMENT ROLLER BRACKET.

INJURED WAS WALKING DOWN THE STAIR WELL OF 4TH FLOOR AND LEEANED OVER THE HAND RAIL TO LOOK DOWN THE NEXT FLOOR AND STRAINED HIS LOWER BACK.

INJURED IS FORMAN AND WAS MAKING HIS NORMAL CHECKS THROUGH OUT PREP PLANT. AS HE WALKED FROM BASEMENT TO 1ST FLOOR. HE DID NOT SEE WHERE FLOOR GRATING HAND BEEN REMOVED. HE FELL THRU THE GR ATING INJURING HIS RIGHT LEG.

INJURED HAD REMOVED GUARD FROM AROUND DIESTER TABLE OPERATING MECHANISON AND WAS ATTENPTING TO ADJUST THE STROKE THE TABLE WAS OPERATING A 6 INCH ADJUSTABLE WRENCH WAS BEING USED TO ADJUST THE DQUARE SET SCREW THE WRENCH SLIPPED CAUSING INJURED THUMB AND FINGER TO BE CAUGHT BETWEEN OPERATING MECHANISM BOTTOM OF CASE.

OPERATING ELECTRIC GRINDER IN TIGHT WORKING AREA, LOST CONTROL OF MACHINE, BLADE STRUCK LEG NEAR KNEE CAP.

I BEAM SLIPPED FROM A PILE OF MATERIAL AND STRUCK EMPLOYEE ON TOP OF LEFT FOOT.

WORKER WAS BENT OVER PULLING #2 WASHED COAL SCREEN INTO PLACE. AS HE EXERTED PRESSURE HE FELT PAIN IN BACK.

INJURED WAS WALKING ALONG BELTLINE WHEN HE SLIPPED AND TWISTED HIS RIGHT KNEE.

INJURED WAS STANDING ON A GRATED WALKWAY APPROX, 42" OFF THE FLOOR. WHEN INJURED ATTEMPTED TO STEP DOWN OFF THE WALKWAY HE MISSED THE STEP AND HIS LEFT FOOT WAS ON THE FLOOR AND HIS RIGHT FOOT WAS ON THE WALKWAY PULLING LIGAMENTS IN HIS KNEE.

A FIRE OCCURRED IN THE CLEAN COASL SILO APPARENTLY HOT COAL FROM THE SHUTDOWN OF THE DRYER WAS DISCHARGED INTO THE SILO.

INJ WAS DRIVING A PICK UP TRUCK RETURNING FORM THE TRUCK GARAGE TO WASHER BLDG. AS HE STARTED ACROSS RAILROAD CROSSIGN TRACK WAS STUCK ON PASSING SIDE BY A TRAIN BACKING THROUGH THE YARD. THI S INJ HAPPEDED ON MONDAY 10-03-88. A(D WAS DECLARED A DISABLING INJ ON 10-15-88.

INJURED WAS LOOSENING A U-BOLT WITH CRESCENT WRENCH THE U-BOLT WAS HOLDING A SENSOR IN LACE ON A PIECE OF ANGLE IRON IN FRONT OF THE BRAD FOR BREAKER. THE BREAKER WAS TURNED OFF BUT HAD NOT COME TO A COMPLETE STOP. A RAISED PLACE ON FRONT OF THE BREAKER CAME DOWN AND CAUGHT INJURED HAND BETWEEN THE ANGLE IRON AND BREAKER.

INJURED WAS ATT9MPTING TO CLOSE THE FIRST FLOOR ELEVATOR DOOR WHEN HIS RIGHT HAND WAS CAUGHT BETWEEN THE CLOSING DOORS.

INJURED AND FEL5OW WORKER HAD REPIRED A 6-INCH WATER LINE. AS INJURED WAS CLINBING DOWN A 4-STEP STOOL HE STEPPED FROM THE SECOND STEP TO THE FOLOOR WITH HIS LEFT LEG.HE LOST HIS BALANCE AND T TWISTED HIS KNE9 FALLING TO THE FLOOR.

INJ HAD REMOVED3COVER AND ADJUSTED BRAKES ON TRIPPER.WHEN HE REPLACED COVER HIS FINGER WAS CAUGHT BETWEEN COVER AND TRIPPER.

INJ WAS STANDING ON MATERIAL THAT HAD PREVIOUSLY BEEN DUG OUT FOR A TRENCH INTO WHICH A CONCRETE FOOTING HAD BEEN POURED INJ WAS DISCUSSING HIS WORK ASSIGNMENT WITH HIS SUPERVISOR WHEN HIS FOO FOOT SLIPPED AND TURNED AND HIS FULL WEIGHT CAME DOWN ON HIS ANKLE

INJ HAD ASSISTE8 A FELLOW WORKER LOAD A RAM CAR SPROCKET ON A FORKLIFT. WHEN HE STEPPED BACK TO GET IN THE CLEAR HE STUMBLED AND FELL. HIS LEFT ARM STRUCK AND BROKE A GLASS WINDOW PANE WHICH CUT HIS ARM 3

INJ WAS ATTEMPTING TO TIGHTEN THE LOBRICATION FITTING ON THE FAN END OF A VIBRATOR MOTOR WHEN HIS FINGER STRUCK AGAINST THE MOTOR FAN

INJURED WAS REPLACING LINERS IN A COAL CHUTE WHEN THE WELD BROKE ON THE ANGLE HE WAS USING AS A FOOTHOLD THIS CAUSED HIM TO FALL IN THE CHUTE AND HIS HAND WAS CAUGHT BETWEEN THE CHUTE BOTTOM AND A PIECE OF 3-INCH STEEL ANGLE THAT WAS HOLDING.

INJURED AND A FELLOW WORKER WERE ASSEMBLING THE TOP VIBRATOR BEARING AND SHIAFT FOR THE CMI DRYER WHEN THE BEARING UNEXPECTEDLY SLIPPED DOWN THE SHAFT AND CAUGHT HIS F INGER BETWEEN THE BEARIN G AND THE SHAFT SHOULDER.

A FOREMAN & 3 WORKERS WERE ATTACHING A SURGE BOX ON TOP OF AN OPEN 12" STAND PIPE THAT VENTED THE M INE ATMOSPHERE OF AN ABANDONED COAL MINE. THE CONSTRUCTION WORK WAS BEING DONE TO INSTALL A SYSTEM OF TAILING DISPOSAL FROM THE PREP PLANT TO THE ABANDONED MINE. ESCAPING GASES WERE IGNITED, BURNING ALL 4. 3 REMAINED HOSPITALIZED OVERNIGHT & BENNETT WAS RELEASED TO RETURN TO WORK.

A FOREMAN AND THREE WORKERS WERE ATTACHING A SURGE BOX TO THE TOP OF AN OPEN 12" STAND PIPE THAT VENTED THE MINE ATMOSPHERE OF AN ABANDONED COAL MINE. THE CONSTRUCTION WORK WAS BEING DONE TO I NSTALL A SYSTEM OF TAILING DISPOSAL FROM THE PREPARATION PLANT TO THE ABANDONED MINE. ESCAPING GASES WERE IGNITED, BURNING ALL FOUR. THREE REMAINED HOSPITALIZED OVERNIGHT AND ONE WAS RELEASED

A FOREMAN AND THREE WORKERS WERE ATTACHING A SURGE BOX TO THE TOP OF AN OPEN 12" STAND PIPE THAT VENTED THE MINE ATMOSPHERE OF AN ABANDONED COAL MINE. THE CONSTRUCTION WORK WAS BEING DONE TO I NSTALL A SYSTEM OF TAILING DISPOSAL FROM THE PREPARATION PLANT TO THE ABANDONED MINE. ESCAPING GASES WERE IGNITED, BURNING ALL FOUR. THREE REMAINED HOSPITALIZED OVERNIGHT AND ONE WAS RELEASED

A FOREMAN AND THREE WORKERS WERE ATTACHING A SURGE BOX TO THE TOP OF AN OPEN 12" STAND PIPE THAT VENTED THE MINE ATMOSPHERE OF AN ABANDONED COAL MINE. THE CONSTRUCTION WORK WAS BEING DONE TO I NSTALL A SYSTEM OF TAILING DISPOSAL FROM THE PREPARATION PLANT TO THE ABANDONED MINE. ESCAPING GASES WERE IGNITED, BURNING ALL FOUR. THREE REMAINED HOSPITALIZED OVERNIGHT AND ONE WAS RELEASED

TRANSFERRING MATERIAL FROM PALLET TO STORAGE LOACATION ,TRIPPED OVER PART PROTRUDING FROM STORAGE PALLET.STRUCK HEAD AGAINST WALL STRUCTURAL CHANNEL AS HE FELL BACKWARD TO CONCRETE FLOOR.

INJURED AND A FELLOW WORKER WERE USING A LIFTING BRACKET AND FORK LIFT TO REMOVE A BATTERY BANK FROM A BATTERY CASE. INJURED WAS USING A 4-FOOT PRY BAR TO ASSIST. WHEN A FIBER GLASS LIFTING EA R BROKE OFF. THIS CAUSED THE LIFTING BRACKET TO FLIP OFF THE FORKS AND CATCH INJUREDS FINGERS BETWEEN THE BRACKET AND THE PRY BAR

INJURED WAS USING A 16LB HAMMER TO SPREAD A PATCH MADE OF SPLIT 6INCH DIAMETER PIPE THIS IS PART OF THE FABRICATION PROCESS FOR A TABLE FEED PIPE BOX HIS FINGER WAS STRUCK BY THE HAMMER

INJURED AND A FELLOW WORKER WERE STACKING 72-INCH BELT ROLLERS WHEN ON E OF THE ROLLERS SLIPPED FROM THEIR GRASP AND CAUGHT HIS FINGER BETWEEN IT AND ONE OF THE PREVIOUSLY STACKED ROLLERS.