Toms Fork Prep Plant and Loadout: 404 citaciones de la MSHA Coal

Employee was cutting pieces of rubber off a screen using downward force with a razor knife. Employee had a rubber piece to tear and the downward momentum resulted with the employee striking right leg with the razor knife. Employee had a laceration and was treated at a local facility that administered treatment with 7 sutures.

Due to the size of the material being loaded there was minimal space to stand on the flat bed. While trying to strap the material down, our employee fell from the truck to the ground.

Tractor trailer was dumping a load when a strong wind gust turned trailer and tractor over. There was about 3 tons of coal frozen in the left front of the trailer due to sub zero wind chill. Truck was on a slight grade. All these factors combined is what caused the accident.

Injured employee was lowering a motor using a 1 1/2 ton chain ratchet and unlocked the ratchet to use the wheel to lower the motor. When the motor began to fall, the employee grabbed the chain pulling EE's hand into the ratchet resulting in a laceration that required 7 sutures and fractured the tip of the left index finger. No Lost or Restricted Workdays.

Employee was using a 10lb hammer to hit a steel beam and the beam shifted, causing the employee to miss and hit the left middle finger on a piece of old metal.

Employee and co-worker were pulling a piece of conveyor belt that was 6 feet wide by 8 feet long and the employee lost his footing and then felt pain in his back. Employee was seen by a physician and removed from work.

Employee states that while he was traveling down the haul road from the refuse in the Cat 777 truck, he hit a hole in the road and jarred his neck and back.

Employee was per-shifting end loader and as he was walking around the machine and lost his footing and fell. As he fell, he tried to put his hands down and catch himself. In doing so he fractured and dislocated his wrist.

Employee received an abrasion to the leg on 4/1/2013, while transporting an electric motor on a carte. Employee was transported to CAMC, where he was treated and release at this time. On July 10, 2013 received medical documentation that ee was treated and diagnosed for cellulites with chronic ulceration at CAMC. EE was give antibiotics and taken off of work.

Was removing rust from steel beam with a 2 lb. hammer and missed intended target and mashed finger.

Employee change trailer caught fire from an apparent electrical malfunction. No injuires involved. Structure destroyed.

Employee was a passenger in a pickup truck being driven by a fellow employee. They were returning from the loadout to the plant after loading a train. The pickup struck a berm and rolled on its right side. Employee received lacerations of the right arm from the accident.

Employee was walking from feed hopper to his end loader. There was a windrow of coal about knee high and he attempted to step over other than walk around it. As he stepped over, he tripped on a lump of coal with his right lower leg striking a sharp piece of coal causing a puncture wound. He received two sutures in treatment of this injury. Missed no work.

employee was riffling a coal sample, lifting buckets, when he felt a "pop" in his back

Employee walked over an embankment as short cut to the equipment parking area. He fell striking his left forearm resulting in a fracture.

Employee was assisting another employee dispose of reject coal. He lifted a barrell of reject coal and felt a sharp pain in the groin area

INJURED JUMPED OFF A TRAILER - AS A RESULT HE SPRAINED HIS BACK.

AT THE BEGINNING OF THE SHIFT, EE REPORTED TO THE IMPOUNDMEN TO COMPLETE THE SETUP OF A PUMP TO REMOVE WATER FROM THE IMPOUNDMENT. THE CRANE WASALREADY IN PLACE & THE PUMP HAD BEEN SET IN THE SPILLWAY OF THE IMPOUNDMENT. THE EE WAS TO PLACETHE SUCTION LINE OF THE PUMP IN THE IMPOUNDMENT TO THE PUMP. HE PICKED UP THE LINE & SWUNG IT OVER THE IMPOUNDMENT. AS THE BOOM OF THE CRANE SWU

EE RECEIVED A 15% PERMANENT DISABILTY AWARD FOR OCCUPATIONAL PNEUMOCONIOSIS.

EE & CO-WORKER WERE REMOVING DEBRIS FROM MAGNET. AN END LOADER BUCKET WEAR PLATE WAS ATTACHED TO MAGNET. EE ATTEMPTED TO PULL WEAR PLATE AFTER A ROPE WAS ATTACHED BACK UP THE BELT TO PREVENT I T FROM FALLING INTO CHARGE CHUTE. WHEN THE POWER WAS REMOVED FROM MAGNET & AS HE PULLED, WEIGHT OF WEAR PLATE PUSHED HIS LEFT ARM DOWN ON A PIECE OF PLYWOOD PUT UNDER MAGNET TO CATCH OTHER DE

EMPLOYEE WAS EXITING THE REAR OF THE FORD F450 SERVICE TRUCK. THE TRUCK WAS EQUIPPED WITH A CABLE STEP MOUNTED TO THE REAR BUMPER. AS HE STEPPED ON THE CABLE STEP, THE WELD CONNECTING THE CABL E AND RETAINING NUT BROKE. AS THE STEP GAVE WAY THIS CAUSED A TWISTING MOTION TO HIS BACK RESULTING IN A BACK MUSCLE STRAIN. HE WAS DIAGNOSED WITH MUSCLE SPASMS AND RESTRICTED FROM WORK.

EE WAS REMOVING A GUARD FROM THE COLLECTING BELT ON THE BASEMENT FLOOR. OTHER EE'S WERE WASHING DOWN THE FLOOR ABOVE. AS HE WAS REMOVING THE GUARD, A RUSH OF WATER CAME FROM ABOVE. HE TRIED TO GET OUT OF THE WAY AND AS HE STOOD UP, HIS HEADHIT A PIECE OF CHANNEL STEEL SUPPORTING THE REFUSE BELT. HE SUFFERED A LACERATION ACROSS THE BRIDGE OF HIS NOSE AND A BLACK EYE.

EE WAS PUTTING IN A 3" DIAMETER PIPE WHILE STANDING ON A 4' STEP LADDER. WHEN HE CAME DOWN OFF THE LADDER HE STEPPED ON A LUMP OF COAL CAUSING HIM TO TWIST TO CATCH HIS BALANCE. HE DID NOT GO TO DOCTOR UNTIL LATER AT WHICH TIME THE SAFETY DEPT. WAS INFORMED.

EE CLAIMS HE PICKED UP A TURNDOWN TO PUT ON A LINE TO A SUMP. WHEN HE PICKED UP THE TURNDOWN TO PUT IT IN PLACE HE HAD TO TWIST WITH IT TO GET AROUND A 4" LINE THAT WAS IN HIS WAY. WHEN HE DID THIS HE FELT A SHARP PAIN IN HIS RIGHT LOWER BACK.

EMPLOYEE WAS REPLACING A SCREEN IN THE REFUSE SIEVE BOX. INJURED WAS LIFTING UP ON ONE END OF THE SCREEN IN AN ATTEMPT TO GET THE SCREEN PROPERLY ALLIGNED. AS HE WAS LIFTING AND PULLING, HE FE LT A SHARP PAIN BETWEEN HIS HIP AND GROIN AREA. ON 9-28, HE FELT A KNOT IN HIS GROIN AND SAW PHYSICIAN. PHYSICIAN DIAGNOSED HIM WITH A HERNIA IN THE GROIN AND SCHEDULED A REPAIR OF HERNIA.

EMPLOYEE WAS RETRIEVING A BOLT FROM A HOLE IN 2-DECKING. WHEN HE ATTEMPTED TO GET UP, HE SLIPPED AND CUT HIS ARM ON A JAGGED EDGE OF THE Q-DECKING.

EMPLOYEE BEGAN SHIFT BY RUNNING A CHOP SAW CUTTING UP CONCRETE. GRADUALLY BETWEEN 7:30-9:30 HIS BACK BEGAN TO GRADUALLY ACHE AND AT 9:30 HE LEFTTHE JOB TO GO TO DOCTOR TO CHECK FOR KIDNEY STON ES. DR DIAGNOSED HIM WITH SCIATICA OF LOWER BACK

WHEN EXITING THE CHANGE BLDG. HE FELT SOME PAIN IN HIS LEFT KNEE. HE CONTINUED TO WORK UNTIL 5-16 AT WHICH TIME HE SAW A DR. THE DR. REFERRED HIM TO AN ORTHOPEDIST. EE WAS SEEN BY DR. ON 5-24 & WAS DIAGNOSED WITH A HYPEREXTENDED KNEE RULING OUT ANY CARTILAGE OR LIGAMENT DAMAGE. HE RETURNED TO WORK ON 5-31.

EMPLOYEE WAS WORKING ON ADJUSTMENT IN THE HEIGHT OF THE SEAT IN THE KOMATSU LOADER. AS HE WAS MAKING THE ADJUSTMENT HIS RIGHT HAND SLIPPED OFF THE ADJUSTMENT KNOB. HE WAS BOUNCING IN THE SEAT ATTEMPTING TO GET THE RIGHT ADJUSTMENT. THE END OF HIS RIGHT MIDDLE FINGER ENTERED THE AREA OF THE SCISSOR MECHANISM AND WAS MASHED AS HE PLACED WEIGHT ON THE SEAT.

EE WAS WALKING FROM THE CHANGE TRAILER ACROSS THE ROAD TO START THE REFUSE DOZER. HE CHOSE TO WALK DOWN A SMALL EMBANKMENT ALONG THE ROADWAY. THERE WAS A LIGHT ACCUMULATION OF SNOW ON THE GROU ND AND THE GROUND WAS FROZEN. THE EMBANKMENT HADBEEN RUN OVER BY A LARGE END LOADER MAKING IT HARD & SMOOTH. WHEN EE STEPPED ON EMBANKMENT HIS FEET SLID & HE FELL LANFDING ON HIS BACK & NECK.

EMPLOYEE WAS OPERATING THE CAT 988B ENDLOADER IN THE COAL YARD. HE STOPPED THE MACHINE TO GET OUT AND STRETCH HIS LEGS. HIS LEFT FOOT WAS RESTING ON THE CAB FLOOR BETWEEN THE FLOOR HORN BUTTON AND THE DE-CLUTCH PEDAL. HE RAISED TO GET OUT OF THE SEAT WHEN HIS LEFT FOOT LODGED BETWEEN THE HORN BUTTON AND TEH BOTTOM LEFT EDGE OF THE DE-CLUTCH PEDAL. THIS TWISTED HIS LEFT KNEE, AGGRAV

EE WAS LOADING A TRAIN WHEN HE DEVELOPED A PROBLEM W/AUTOMATIC SAMPLER. HE WENT FROM CONTROL TO SAMPLER SEVERAL TIMES. HE REMOVED INSPECTION PLATE FROM TOP OF SAMPLER AND FOUND SAMPLER HOPPER CLOGGED. HE REACHED IN WITH HAND SCOOPING EXCESSCOAL OUT OF HOPPER. WHEN SAMPLER FREED AND CAUGHT HIS RIGHT ARM BETWEEN TOP OF HOPPER AND SAMPLER ENCLOSURE. WAS CAUGHT 45-60 MIN. BEFORE FREED

INJURED EE WAS ASSISTING CO WORKER INSTALL 3 INCH WATERLINE. THEY HAD WELDED TWO SECTION OF PIPE TOGETHER ON THE CATWALK. THEY PROCEEDED TO LIFT THE COMPLAINED SECTION ONTO THE MOUNTING BRACKE TS. AS HE WAS LIFTING. HE FELT A PAIN IN THE LOWER BACK PAIN LEFT AND HE WORKED REMAINES OF SHIFT BUT FAILED TO REPORT INCIDENT TO SUPERVISOR. ON SEPT 29 INJURED EE CALLED IN REPORTING INCIDE

EE WAS STRIKING A BEARING RACE WITH A HAMMER I REMOVE IT FROM THE SHAFT OF A PUMP WHEN THE RACE SHATTERED AND A PIECE OF THE METAL STRUCK AND EMBEDDED IN THE RIGHT INDEX FINGER.

EE WAS CHANGING OUT FEED PIPE IN PLANT. HE WAS HOISTING OLD PIPE OUT OF THE WAY WHEN IT SWUNG BRUSHING EE CAUSING HIM TO STUMBLE BACKWARDS TRIPPING ON NEW PIPE LAYING IN THE FLOOR AND CATCHING HIMSELF AGAINST CENTER WELL HANDRAIL.

EE WAS STANDING ON A 2'X10' BOARD USED FOR SCAFFOLDING WHILE PLATING REFUSE BOX WHEN THE BOARD BROKE ALLOWING HIM TO FALL APPROX 6 FT INTO A CHUTE AND ONTO THE VIBRATE.