WHITE ROCK QUARRIES Metal/Non-Metal

EE was welding dragline bucket chains. At some point, a small metal fragment entered EE's right eye. In the initial consultation, a doctor removed the foreign object. At a follow-up visit, antibiotic drops were prescribed for an infection that had developed.

While working on the Concrete Metso Hammers, a small piece of metal shaving impacted their left forearm causing a very small laceration.

rubber strap access step to service truck bed broke

EE's cutting torch on the service truck wouldn't light. Upon inspecting the truck, EE found the acetylene quick connect had separated. When EE reached into the compartment of the truck, the acetylene gas that had escaped ignited, causing first degree burns to EE's left hand, abdomen, and face.

Employee was walking when EE stepped into a small hole/impression in the ground. EE's right hip shift unexpectedly causing discomfort. On Monday, while on shift, EE notified the supervisor, for the first time, that EE was in pain, then EE was taken to Concentra MC. Diagnosis Sprain of Right Hip. released with restrictions. We will provide work under those restrictions.

Employee was removing a shaft bearing when EE struck EE's left little finger with a 4-pound hammer, sustaining a laceration requiring stitches.

When placing the hose on the connection, the end of the hose that connects to the water hose hit employee.

When the employee attempted to mount a dozer, EE slipped and fell.

As EE was dismounting a 992 pit loader EE missed the last rung of the ladder, causing EE to put all EE's body weight on EE's arm, causing a sprain to EE's left wrist.

While EE was cleaning around the weight scales EE was bitten by an insect in EE's right buttock area.

EE has never reported any related Accidents, injuries or issues involving EE's shoulder. EE has been under the care of EE's primary physician for approximately 6 months. EE approached us on 11/06/23 stating that EE thought that this issue with EE's shoulder could had happened from working throughout the years.

While EE was cleaning and preparing the Bohringer Crusher for maintenance, EE slipped and fell (same level) onto buttock causing some pain to EE's lower back area. EE was taken to Medical Center, for medical attention.

While employee was resetting the hammers on M48 Crusher, the tool that was been used slipped out of their hands impacting EE in the lip.

Picking up for the company in the rain and tripped and fell from the stairs

EE was working / cleaning around M216 conveyor area with a water hose, when suddenly and unexpectedly EE felt a pain on EE's left knee.

Working on loader assembling the center hitch, was setting rear frame on to jack stands 25 ton with 3' tubes, was adjusting the tube that sets the height, as they pulled pin that adjusts this left hand ring finger was caught in the hole of the jack stand, as tube slid down it slid onto the finger caught in the jack stand hole.

While working on M20 conveyer, a rock bounced of the empty conveyer impacting the employees hard hat.

Employee threw welding connector, looks like a clamp, it bounced back at their nose.

While EE was walking to M215 Conveyor, EE stepped on a rock which caused EE to shift weight to prevent twisting ankle. This maneuver caused a strain to EE's right knee.

EE was working on M33 crusher when a single rock that was stuck on M26 conveyor head pulley, fell striking EE on EE's hard hat.

Employee was cleaning with a water hose, the hose became tangled causing them to twist left arm.

When was working on M26 Conveyor, a rock bounced off the belt impacting the left leg (calf). EE suffered a minor contusion from the impact of the rock.

While working on the DL the EE had water drip onto forehead. The water ran under EE's safety glasses and into eye. When the EE woke up the next morning the eye was irritated. The EE was taken to the DR. EE's eye was flushed out. DR prescribed antibiotic eye drops. EE returned to work.

EE tripped over a very small sand pile, causing EE to fall and impact the ground. The impact caused a contusion to EE's forehead, above the right eye. EE complained of neck pain, but refused medical attention, was given first aid. EE told supervisor EE would notify supervisor in the morning if the pain persisted.

EE was cutting a wear plate from a 4'x8' steel sheet plate with a track torch. As EE reached the end of the final cut the plate became unstable causing it to fall impacting the floor first and then EE's right foot.

Employee was crouched down behind MCC-1 and Approximately 13' in front of welding truck; preparing a skirt rubber for M-22 Conveyor. Driver got into the truck and began driving forward not seeing employee, impacting them and running over legs near the ankle, causing a fracture to the left leg just above the ankle.

EE was working on M-11 using the pressure washing truck, as EE stepped down from the truck EE's fingers got stuck between the handrail and taillight causing a laceration of the small finger in the right hand.

The utility Knife employee was using to cut a section of the conveyor belt slipped causing a laceration of right leg.

While hosing off excess material from a portable crusher a piece of foreign matter entered employee's eye.

EE lacerated the palm of left had on the belt support bracket of the Pioneer Crusher, while retrieving the belt support cross member.

The utility knife the employee was using to cut the skirt rubber slipped causing a laceration of employee's arm.

When tightening a bolt on a liner with a pneumatic impact gun a piece of microscopic debris went under EE's safety glasses, lodging in the eye.

Employee was replacing the wire spool of the wire feeder, when the guard/cover closed impacting their head.

EE was standing on the M33 Crusher Platform, when a rock (6" -8")fell from above bouncing off the empty M26 conveyor. The rock struck ee hard hat and right arm.

The day following shoveling fine material, employee said they felt soreness in their back but refused a medical exam or treatment. A medical checkup was not requested until 6/27/2017 at which time they received an appointment on the 28th.

EE slipped into a gator hole which was covered by vegetation while walking during the performance survey duties, causing knee to impact the ground and/or twist.

Walking backwards while using a hose to clean a discharge ditch employee lost balance falling backwards (on the same level). Employee sprained left hand/arm trying to break fall.

EE slipped on the M-14 deck while walking towards the stairs. EE grabbed the handrail with right hand which prevented ee from falling but caused a strain to right shoulder as ee was successful in keeping body from landing on the deck.

Employee's right thumb was crushed and nail bed damaged (nail avulsion) when EE placed their hand in the door jamb that closed unexpectedly. Diagnosis: Avulsion fracture of rt thumb; laceration of rt thumb.

A piece of anvil broke loose impacting EE leg; requiring 4 stitches; when EE struck the anvil to be removed with an 8 pound sledge hammer.

EE hit his left knee against the dozer track while he was dismounting the Cat D6 after he had fueled the dozer. The accident occurred on 10/8/2015 but ee did not request medical attention until 10/29/2015.

EE was moving a plate liner to work with it when his finger was caught between the liner an another piece of metal injuring his finger.

As employee was unscrewing the hydraulic hose on the tramping cylinder the residual pressure in the hose caused it to come off quickly, striking his finger. NOTE: Employee initially refused medical treatment until 3/13/2015 at which time he was treated and returned to work able to his fulfill his job responsibilities.

The ladder that employee was using slipped and fell as he was dismounting.

While cleaning his right shoe on the cab level platform of his Cat 988H loader, employee fell backwards down the steps.

Using an air impact gun to adjust V-Belts, employee sprained the tendons in his forearm.

Employee was cutting a round bar using his left hand to hold the bar and the right hand to operate the welding torch. The heat from the torch burned his left wrist.

Employee was working on the M12 grizzly feeder, as he walked on the top deck he slipped and the right leg slid between the grizzly bars causing a sprain

A steel plate which had been put on the rear platform of his mechanic's truck fell onto employee's boot just above the steel toe cap. The torch hose caught the corner of the plate causing it to fall and injure his foot.

While wearing his safety harness, employee was inspecting the feeder pan when he slipped on a small rock and fell (on the same level) on to his buttocks.

Rock from an overhead conveyor fell striking EE's safety glasses; causing a contusion of the lower eyelid of the right eye.

The day following employee's work assignment to change a motor for a lube oil pump, he felt a pain in his lower back.

Dismounting the portable crusher ee missed a step causing him to apply all his weight on the right leg/knee.

EE was removing a screen from the M31-31 shaker when it slipped down striking his right index finger.

Employee could not control the water hose when the valve to the pump was opened causing him to fall, injuring his head and right shoulder.

Employee could not control the water hose when the valve to the pump was opened causing him to fall, injuring his leg.

Removing release valve when it blew and hit employee on the right side of his chest.

EE WAS USING A SLEDGE HAMMER TO REMOVE THE BLOW BARS FROM THE STEDMAN CRUSHER. WHEN THE SLEDGE HAMMER IMPACTED THE BARS IT RICOCHETED HITTING HIS LOWER RIGHT LEG.

Employee was attempting to hammer the pin that holds the tilt cylinder on a 98H loader into place. The pin fell hitting him on the left leg just below the knee causing a laceration which required stitches.

Employee was standing by the screens of the Pioneer Crusher when he felt something in his eye.

Employee felt a pinch in his lower back as he dismounted the pressure washer truck.

Employee dropped a tool inside a chute. He cut his forearm on a piece of flat bar while reaching to the tool.

EE attempted to lift the engine compartment door to gain access to the radiator when he strained his back.

EE was holding the bladder with a pair of vice grips while a co-worker was removing the steering accumulator. The vice grips opened striking EE on his lower lip.

While lubricating heavy equipment using latex gloves employee developed dry hands which lead to lacerations on his hands.

Employee was climbing on to the Cat 988H front end loader when he slipped and fell. His left elbow and knee struck the loader during the fall. The clinic gave first aid to his contusions. MSHA definable treatment did not begin until the MRI performed on 1/19/2012.

EE was exiting the cab of his loader, missed the step, fell forward and grabbed the railing applying force to his elbow.

Delivery Driver opened the door of his tri-axle delivery truck and stepped out to get his delivery ticket. His truck rolled back pinning his left thumb between the truck's door and the frame around the delivery ticket printer.

EE first came to us on 3/16/2011 saying he was experiencing back pain. He did state that the pain was caused at work. On May 2, 2011 he saw a doctor who indicated that his operating of a bulldozer was partially responsible for his back pain. The doctor prescribed medication.

Customer's truck driver, fell from his truck causing lacerations to his head and right hand.

EE was exiting the shaker screen unit when he misjudged the foot hold he expected, which made him to slip causing his left arm to support all his weight and dislocating his shoulder.

Lifting a roll of conveyor belt EE stepped on a rock causing him to twist his knee.

EE stopped at a stop sign within the quarry area when co-workers mechanic's truck drove into the back of EE's truck at 5 or 6 miles and hour.

EE's finger was caught between a chain holding the pitman and the pitman itself when the toggle plate shifted.

Wind blew down a tarp post which fell on employee as he was sitting in his chair

Injury jumped about one and one half feet from the concrete plant foundation to the ground. When he landed he felt a pain in his right knee. He did not think it was a reportable injury, but the next day the pain continued and got worse.

Dismounting loader engine compartment employee slipped and fell hitting his knee on the rocker assembly.

Mounting his Caterpillar 777C haul truck, employee stepped on the first rung of the ladder and felt a pain in his knee.

EE was opening a water valve, when a rock fell from the plant screen above, striking the steel toe on his right boot.

Installing a guard near the timing belt, Injury hit his hand with a crescent wrench.

Unknown. The cause of the shoulder sprain is not yet known, even after medical examinations.

While turning the Hammer on crusher M-48 employee's finger was caught in between the hammer and the wall.

ATV trespasser lost control and flipped forward. Laceration to the head.

Exiting the front end loader employee slipped on the steps and fell.

While assembling the conveyor to the platform, the weight of the platform shifted causing the platform to strike his knee/leg. The chest and back contusions probably occurred while falling to the ground.

While loosening the liner from a cone crusher with a hammer a piece of metal came off and entered his hand.

Employee was hammering a tooth on a loader bucket to loosen it for removal. A metal chip came off the bucket tooth and lodged in his left arm.

Climbing up the ladder to enter the cab of the Caterpillar 785 Haul Truck, employee slipped and fell approximately 5 to 8 feet to the ground. The area in which the truck was parked was muddy.

When employee was setting up a pull cable, the cable fell hitting and cutting his right leg.

Miner was clearing material from tail pulley area, when he hurt his back.

Employee said that his shoulder began hurting on 3/13/2007. He could not identify an incident or specific event that tiggered the pain. We had him go to an orthopedic doctor who indicated that in his opinion the shoulder pain was a work-related condition.

Tried to pull right foot out of fine silt material and felt a muscle pull at the back of his foot

Unknown insect bite EE on or near his eye.

Employee was welding and felt something go into his eye.

Employee was dismounting a dozer when he hit his knee against the dozer track.

Drill helper put his hand between kelly bar and the steel tube cap which is used to hold the tube down while the outer kelly bar is being pulled out of the ground. His arm was caught and pulled down iunto the borehole. The drill bar slipped on top of driller's hand. EE had surgery and lost right index finger, other broken fingers and lacerations to forearm.

He burned his forearm when he dropped the cutting torch he was using to cut plates in the plant.

Fell from Cat 740 Haul Truck after completeing refueling the truck and attempting to dismount.

Employee struck his L-hand middle finger with a sledge hammer while hammering piece into place resulting in a closed fracture to middle phalanx.

Operator of Cat777C Haul Truck fell asleep while driving empty truck to the pit. H/T ran off the road over the berm into rough terrain. Damages to H/T frame and minor injuries to operator.

The welder was grinding metal with disk grinder. He was wearing proper PPE consisting of safety glasses & welding hood. A piece of metal entered his right eye. The metal was imbedded in the cornea.

IE, who is a haul truck driver felt a sharp pain to his neck every time his truck hit a bump. Cont. cause: Unusual postures or repet. motions.

IW received lacerations to left ear and face & head contusion after he was struck by a 20-Ton bottle jack that slipped off while it was being used to raise a screen shaker. Failure to restrain the jack with chains to prevent ejection in case of slip off was the main cause of accident.

Open fracture of L-hand middle finger distal phalanx (tip) resulted after screen shaker pulley being replaced by IE slipped and fell over IE's injured body part. IE is being treated by physician. He is working under restricted duty (no use of L-hand). Contributing cause: IE failed to use proper mechanical devices (come-a-long) to hold pulley in place while being replaced.

IW was on ground ~ 4 feet from basket of manlift. Operator placed manlift in reverse motion, wheels turned right. Boom/basket abruptly swerved left and struck IW on right side of body. Left hand of IW got caught between midrail of basket and conveyor column causing L-hand laceration, left index finger fracture and partially severed L-thumb. Cause: untrained operator for equipment.

EE was on a conveyor belt that slide down, which caused him to twist and he injuring his ankle.

EE WAS CUTTING ROUND BAR ON THE HAMMERS WHEN A PIECE OF HOT SLAG FELL ON THE THE TONGUE OF BOOT. THE SLAG BURN THROUGH THE BOOT AND BURNED THE TOP OF EE FOOT

EE WAS HELPING TO INSTALL THE 3RD RAIL ON THE RIGHT HAND SIDE OF THE MACHINE. CO-WORKER ASKED IF WE NEED TO TIGHTEN ALL THE BOLTS ON THE 3RD RAIL. EE SQUATTED DOWN AND CALLED TO ASK ABOUT IT. HE LOST HIS BALANCE AND FELL ACROSS THE RAIL ONTO HIS BACK.

When the employee climbed down from the fuel farm deck on to the lube truck, he fell.

EE MISSED THE LAST STEP OF THE STAIRS WHEN EXITING THE PIONEER CRUSHER. HE STEPPED OFF THE CRUSHER ACKWARDLY, PULLING HIS SHOULDER.

WHILE OPERATING AN AIR IMPACT WRENCH, USING HIS LEFT HAND TO GUIDE THE SOCKET, HE CUT HIS FINGER.

EMPLOYEE SLIPPED AND FELL ONTO A PIECE OF ANGLE IRON; CUTTING HIS THIGH.

While landing a section of conveyor, set down on top of foot.

EE was replacing the hammers on M33 Crusher. During the installation the new hammers slipped. His right hand was breifly caught by the hammer and he jerked his hand back. The result was a sprained wrist and crush injury to the 4th finger.

A WATER HOSE WHICH HAD JUST BEEN TURNED ON SLIPPED FROM THE HANDS OF AN EMPLOYEE AND THE WATER STRUCK VICTIM IN THE EYE.

EE WAS ATTEMPTING TO REPOSITION THE TRAILING CABLE WITH AN INSULATED CABLE HOOK. THE CABLE WAS DAMP AND AS HE STARTED TO PULL ON THE HANDLE, THE HOOK SLID ALONG THE CABLE. HE LOST HIS BALANCE AND FELL BACKWARDS STRIKING THE BACK OF HIS HEAD ON THE D-RING OF THE CABLE TRACTOR PARKED NEARBY. THE BLOW CAUSED A LACERATION WHICH REQUIRED 9 STITCHES TO CLOSE.

EE WAS DISMOUNTING THE PAYSTAR FUEL TRUCK WHEN HIS FOOT MISSED THE STEP. HE FELL TO THE GROUND INJURING HIS HIP/PELVIC AREA.

EMPLOYEE WAS TURNING THE ROTOR SHAFT IN ORDER TO CHANGE THE HAMMERS. WHEN THE ROTOR SHAFT MOVED FURTHER THAN INTENDED HE TRIED TO GET OUT OF THE WAY, BRUISING HIS RIGHT LEG AND DISLOCATING HIS LEFT SHOULDER. NOTE: SHOULDER HAD BEEN DISLOCATED PREVIOUSLY. DOCTOR SAID SHOULDER WAS UNSTABLE PRIOR TO ACCIDENT.

EE FELL A SLEEP WHILE DRIVING A HAUL TRUCK.

CLAMP ON HOSE CUT HIS HAND WHEN THE HOSE SLIPPED FROM HIS HAND.

STRAINED BACK WHILE ENGAGING CLUTCH OF THE ROAD ROCK CRUSHER.

THUMB WAS CAUGHT BETWEEN A ROCK AND THE TIRE OF THE STACKER.

SAFETY LATCH ON THE RAIL CAR DOOR RELEASED, CATCHING THE FINGER BETWEEN THE LATCHES AND THE RAIL CAR DOOR.

CUTTINT DELIVERY BELT DURING REPAIR WORK WHEN THE KNIFE SLIPPED, CUTTING EE'S LEFT ARM.

EE SLIPPED OFF BACKHOE STEP & FELL BACKWARD HITTING HIS ELBOW ON A PIN.

WHEN THE SHAKER WAS BEING REMOVED FROM THE ROAD ROCK CRUSHER , EMPLOYEE'S LEFT HAND WAS PINNED BETWEEN THE SHAKER AND A STEEL BEAM.

EMPLOYEE WAS CLOSING GATE, TRUCK ROLLED BACKWARD CATCHING EMPLOYEE BETWEEN TRUCK BUMPER AND GATE RESULTING IN INJURY.

AFTER COMPLETING THE WELDING TASK EMPLOYEE FED THE EXCESS WIRE BACK THROUGH THE WIRE FEED MACHINE ONTO THE WIRE REEL ASSEMBLY, EMPLOYEE'S FINGERWAS CAUGHT IN THE WIRE FEED GEARS.

LEFT FOOT SLIPPED ON LADDER CAUSING BODY WEIGHT TO SHIFT TO RIGHT LEG. THIS CAUSED INJURY TO RIGHT KNEE.

STEPPED ON ROCK WHILE DISMOUNTING FORKLIFT & EE FELL

PIECE OF METAL FELL STRIKING EE ON THE LEFT SIDEOF HIS FACE

FELL HITTING HIS FOREHEAD WITH SCREEN WHICH HE HAD PICKED UP

PIECE OF METAL FROM A CHIPPING HAMMER WENT INTO EE'S HAND

FINGER CAUGHT BETWEN A BAR & THE PLANT FRAME

AFTER WELDING EE'S EYE BOTHERED HIM

TRIPPED AND FELL BACKWARDS.

SLIPPED ON LADDER WHEN MOUNTING GRADER

FINGERS OF LEFT HAND CAUGHT BETWEEN TWO PIECES OF METAL.

WALKING AND FELT A PAIN IN HIS RIGHT CALF MUSCLE.

DURING HEAVY RAIN EE LOST HIS GRIP ON THE LADDERAND FELL TO GROUND. THIS IS REPORTED BY THE EE NO WITNESSES.

USING WRENCH TO ADJUST HAMMERS WHEN HE FELT A PAIN IN HIS UPPER BACK.

SLIPPED WHILE DISMOUNTING FRONT END LOADER.

EE WAS CUTTING THE FLANGE ON THE PIPE THE PIPE BROKE LOOSE AND STRUCK HIM ON THE RIGHT LEG.

FELT PAIN IN LOWER BACK WHILE CARRYING A STEEL PLATE.

TWISTED ANKLE WHEN DISMOUNTING FRONT END LOADER.

FELL DISMOUNTING HAUL TRUCK.

FINGER WAS PINCHED BETWEEN ROUND BAR AND ANOTHER PIECE OF METAL.

SPRAIN ANKLE

EMPLOYEE JUMPED OFF OF FALLING LADDER.

GREASE PRESSURE HOSE/COUPLING DEVELOPED A LEAK THAT INJECTED GREASE INTO EE'S HAND.

PULLY SLIPPED OUT OF HIS HANDS AND LANDED ON HISANKLE.

STEPPED ON ROCK & TWISTED ANKLE

STEPPED ON ROCK WHEN GETTING OUT OF TRUCK AND SPRAINED HIS ANKLE.

HAMMERING PIN INTO A STEERING CYLINDER WHEN THE PIN SLIPPED AND PUNCTURED HIS LEFT LEG.

ROCK FELL ON EMP'S HARD HAT CAUSING HIM TO FALL.

BALL HAMMER HEAD STRUCK LEFT HAND.

FELL BACKWARDS WHILE PULLING ON A HOSE.

DUST IN LEFT EYE.

FINGER CAUGHT BETWEEN TWO PIECES OF METAL BEING BOLTED TOGETHER.

HAND SLIPPED CAUSING HIM TO FALL ON TO TRACK PAD.

BEARING CAP FELL ON LEFT HAND WHILE INSTALLING TRAVEL SHAFT.

EMPLOYEE WAS HIS RIGHT HAND ON THE HOIST AND TILT LEVERS GOING INTO A PILE WHEN HE FELT A PAIN FROM HIS RIGHT NECK GOING DOWN TO HIS SHOULDER BLADE.

REMOVING ROCK FROM CONVEYOR. THE ROCK CAME OFF CONVEYOR--PINNING HIS FINGER AGAINST THE CONVEYOR SUPPORT STRUCTURE.

WHILE PREPARING TO SET WEDGE THE CABLE SLIPPED & CUT EE FOREHEAD

THE EE PLACED HIS HAND IN AN AREA THAT COULD BE CONSIDERED A PINCH POINT DUE TO THE NATURE OF THE ACTIVITY IN THIS AREA. THE SAME EE THEN USED ATOOL TO MANIPULATE A PIECE OF MATERIAL INTO THE AREA OCCUPIED BY HIS HAND. THE EE TRAPPED HIS THUMB BETWEEN THE MATERIAL & THE TOOL CAUSING LACERRATIONS.

PIPE STRUCK TOP OF RIGHT FOOT

EE WAS CHANGING SUMP OIL WHEN LIGHNING STRUCK THE DRAGLINE BOOM

PULLING PIECE OF METAL FROM THE RACK EE SLIPPED & FELL

WHEN CHANGING THE DRAG CABLE EMPLOYEE'S THUMB WAS CAUGHT BETWEEN THE HANDLE OF THE B & D (PUNCH TOOL) AND THE WALL OF THE DRAGLINE.

CLOTHING CAUGHT FIRE. CONDITIONS ARE STILL UNDER INVESTIGATION.

INJURED WAS ADJUSTING BREAKER WALL WHEN HE SLIPPED AND FELL.

PRY BAR SLIPPED & HIT INJURED IN JAW.

PICKED UP SCREEN AND EXPERIENCED A PAIN IN LOWER STOMACH.

PLANT CRUSHER HAMMER SLIPPED OFF TABLE ANDFELL ON FINGER.

DRIVE SHEAVE WAS BEING REMOVED FROM ROAD ROCK CRUSHER AND FELL ON FINGER.

WELDING I GOT RED EYES.

CLIMBING ON TO LOADER I HIT MY HEAD ON MIRROR BRACKET HARD HAT SAVED INJURY BUT LOST BALANCE AND BEGAN TO FALL. I CAUGHT MYSELF BY GRABING RAILING WITH RIGHT ARM CAUSING PAIN TO NECK AND SHOUL DER.

EMPLOYEE FELL ON RIGHT SHOULDER.

WHILE SHOVELING, I STRAINED MY ARM/ELBOW.

EE CUT HIS KNUCKLE ON THE SHARP EDGE OF A WIRE SCREEN WHILE INSTALLING A SIDE RAIL.

SMASHED THUMB WHEN HE CLOSED CRUSHER DOOR

SLIPPED WHILE CUTTING A CABLE RESULTING IN A MUSCLE PULL OF RIGHT ARM.

EE WAS LOADING CRUSHER LINERS ON THE BOOM TRUCK WHEN A LINER SLIPPED OUT OF EE S HAND. IT CAUGHT HIS FINGER BETWEEN THE LINER AND THE TRUCK BED.

EE WAS REPLACING A JACK SHAFT WHILE MOVING THE JACK SHAFT IT WAS DROPPED ON RIGHT LOWER LEG.

EMPLOYEE WAS COMING IN TO THE MAIN SCALEHOUSE FROM THE SECONDARY INCOMING WEIGH BOOTH. HE JUMPED DOWN FROM THE SCALEHOUSE RETAINING WALL ONTO THE ENTRANCE STEPS. THE STEPS WERE WET & HE SLIPPE D - HITTING HIS ELBOW ON THE DOOR WINDOW REAKING IT. THE BROKEN WINDOW CUT HIS ARM.

HE WAS USING A 1-1/2" WRENCH TO LOOSEN A BOLT SO THAT HE COULD CHECK ON THE OIL LEVEL OF S-81 CAT HAULER. THE BOLT LOOSENED. THE UPWARD MOTION OF THE ARM FROM THE BOLT LOOSENING CAUSED HIS ELB OW TO STRIKE THE RIM.

EMPLOYEE AND ANOTHER WERE SETTING HAMMERS INTO A TRUCK. OTHER EMPLOYEE DROPPED A HAMMER ON EMPLOPYEE CAUSING A CHIP OF METAL TO FLY OUT & MAKE A PUNCTURE WOUND IN EMPLOYEES NECK.

HELPING TO CHANGE TOOTH, EE HIT THE TOOTH WITH A HAMMER. A CHIP OF METAL CAME OFF AND PUNCTURED HIS FOREARM.

WHILE WELDING HAMMERS IN CRUSHER, WAS TURNING THE ROTOR WITH HIS FEET HE SLIPPED AND FELL.

WHILE INSTALLING STEEL PLATE, EE WENT TO SET IT DOWN. HE CAUGHT HIS THUMB UNDER THE PLATE AS HE SET IT DOWN.

EE SAW A PIECE OF PLASTIC STUCK UNDER HIS PICKUP. HE WENT UNDER THE TRUCK TO PULL OFF THE PLASTIC WHEN SAND/PARTICLES FELL INTO HIS EYE.

EE WAS TAKING OF THE GREASE PUMP. HE HAD THE FRONT TWO BOLTS OFF AND REACHED BEHIND TO LOOSEN THE BACK BOLTS THE PRESSURE FROM THE GREASE PUMP FORCED THE PUMP BACKWARDS PINNING HIS HAND AGAINS T THE VALVE PLATFORM.

WHILE WELDING ON SHAKER SCREEN A PIECE OF SLAG WENT INTO HIS EAR.

TRUCK DROVER TOO FAR TO THE RIGHT GOING OFF THE MAINR OAD AND INTO THE BERM. DRIVER DID NOT REGAIN CONTROL OF TRUCK AND IT ROLLE DONTO IT'S SIDE. THE DRIVER WAS NOT WEARING HIS SEAT BELT AND HIT HIS HEAD. NOTE: WEARING SEAT BELTS IS REQUIRED AND IT HAS BEEN DISCUSSED INS AFETY MEETINGS.