Winfield South Strip Coal

Fire was started by lightning strike at H area at Winfield South mine. Fire department and forestry service responded and extinguished the fire and cut fire road around fire. Approx. 9 acres affected. No injuries or property damage. Fire area was monitored to ensure it did not reignite. Fire was extinguished in approximately 1 hour and 20 minutes.

Individual was operating torch to cut sections of plate. While checking how much remained to be cut, the piece came loose of the structure, pinching the upper ring finger against plate below. This caused a laceration through the welding glove as EE pulled the hand free. The laceration required three stitches. X-rays were forwarded to radiology and resulted in negative findings.

The employee was pulling on a steam cleaner hose and tripped over dirt clod and fell back and strained employee's left hamstring.

Employee injured his neck while riding in a pump truck in route to a barge pump.

A contractor was cutting a hole in the roof of the 2570 BE dragline to make "A" leg repairs. During this process sparks fell around the drag gear case and ignited grease. Efforts to extinguish fire with portable fire extinguishers was not successful and the local fire department was called out to extinguish the fire. No injuries to the miners and fire fighters.

EE was pulling up on the front major bogie frame and felt sharp pain in right shoulder.

Sparks from locomotive started extremely dry grass on fire. The fire started off the mine at approximately 11:20 and spread on to the property at approximately 12:20 p.m.. At that time a Luminant supervisor called the MSHA 800 number to report it had burned 30 minutes on mine property. The fire was located in a non-active area of the mine.

Lightning struck an arrestor on a power line and caused sparks to fall down on an extremely dry field. There was no miners fighting the fire but fire departments from Winfield and Mt. Pleasant came out to control the fire. The location of the fire was in a remote area of the mine, no mining activities were close to this event. The fire burned approximately two hours.

Fire was started beside railroad track in a remote area of the mine. The fire was extinguished by the Mt.Pleasant fire department at approximately 7:35 p.m. No damage was done to any equipment nor injuries to personnel fighting the fire. No miners were involved in fire fighting efforts. Cause of fire was not determined.

EE was bending over machine all day and his back was sore the following day. Did not report to HR till 11/14/10

Employee drove his haul truck off the roadway and bumped his head on the steering wheel, resulting in cuts that required stitches.

Employee was helping another employee to remove a becket pin from an intermediate cable and the pin hung up and then the pin came loose and dropped on cable and smashed little finger of left hand.

Employee was moving trail cable and got his pinky finger of left hand piched resulting in several stitches.

Employee was in process of sawing through a PVC pipe that was located in an area that was causing tension on the pipe. When the employee cut completely through the pipe, the tension caused the pipe to snap up and trap his finger between it and a metal support. This caused a laceration on the top side of the right index finger of the employee.

Injured was putting trail cable shoe on the back of the truck and dropped it on his middle finger of left hand.

While stripping dirt from spoil side with 2570 dragline the spoil became unstable. There was no equipment damage or injuries due to this event. The reason for reporting is that it interrupted coal haulage for over one hour.

Employee was cutting toe plate on a pump barge when the metal sprung back and struck him in the mouth.

Was climbing back on his D10 dozer when his foot slipped & he caught himself with his left foot, hper-extending it upward, pulling tendons in his left lower leg.

Employee was installing wear plate on dragline bucket. As he turned to get another piece of metal he tripped and landed on his side resulting in two cracked ribs.

Employee was tightening bolt on stabilizer bar on dozer and struck finger, on left hand, with 4 lb. sledge.

The employee was walking the dragline and tripped, falling on his left shoulder. This became reportable when employee started therapy on 5/21/07.

Employee was assisting in installing a final drive on a Hitachi 1800 back-hoe when he mashed his left thumb.

New dump ropes were being installed on the dragline, as a wedge was being put on it slipped and mashed employee's finger.

Employee fell back on his left knee resulting in a torn quad tendon.

Employee was assisting in changing out dragline teeth on bucket. A fragment of metal chipped off the tooth and struck employee in left arm.

Employee was testing a Siemens drive on the Cross Pit Spreader and was electrically shocked by test leads.

Employees were hooking up to a truck to pull a kink out of a 6" collapsed pump discharge line that was laying embedded in the grass. When the truck began to pull the discharge line and remove the kink the hose became very taunt, then instantly the hose snapped out of the embedded grass and hit the employee on the side of his lower left leg.

Employee was driving a t-post with a t-post driver, as he raised the driver up above the t-post the driver had come off the top of t-post, on the way down, the employee's finger was caught between the t-post and the handle of the t-post driver. This caused the end of his finger to be severely cut between the two pinch points.

Using pry bar while installing trans. oil cooler, bar slipped, causing little finger to come in contact with sharp edge on hardnose of dozer.

Employee was walking beside the dragline and tripped over a clod of dirt. While breaking his fall he broke his right arm.

Employee was getting off of a truck bed and was using a tool box to steady himself and the tool box lid shut on hand.

Employee was guiding a motor which was being moved with a sled and mashed his finger between a piece of conduit and a pry bar. The cut resulted in the employee getting stitches to close the wound.

Employee was grinding on a bolt and the grinder kicked back and cut left forearm.

Employee was removing upper penant line pins at the boom point of a dragline. He was using a Link-Belt to hold socket up while driving the pin out. As the pin was being struck with 5 ft. pry bar it came out causing the pry bar to swing back and strike the employee in the left side of the head.

EE WAS SQUATTED DOWN ON LEFT SIDE OF THE ENGINE COMPARTMENT TO LOOSEN A SMALL BOLT. WHEN HE STARTED TO STAND UP HE FELT A CATCH IN HIS BACK.

This accident occurred on 5/20/2005 but was not reported till 5/25/2005. At D-24 the spoil was sliding towards the power cable. Employee got the dozer operator to help him move cable with the dozer. The rest of the cable he had to move by hand. The dragline was held up while moving the cable into shoe print where the shoe would not drag the cable when it turned.

EE WAS DISMOUNTING LEFT SIDE OF LOCOMOTIVE TO REPAIR FLASHING MARKER LIGHT. STEPS WERE WET AND EE SLIPPED OFF FROM SECOND STEP FROM TOP. EE HIT HIS RIGHT ELBOW ON STEP AS HE WAS SLIDING HANDS DOWN THE HANDRAIL.

As the employee was dismounting a D-10 bulldozer he slipped and fell, this resulted in an injury to his hips.

Mashed the end of his finger while attempting to install a shaft in a gear box.

Employee was putting feeder chains back together with master link and driving keeper pins in when he hit his finger with 4# hammer.

Employee was helping electrician to roll up cable when he stepped into a hole and twisted his back.

Employee was fueling hauler. When he stepped on catwalk of hauler to get back on fuel dock platform, the catwalk of hauler fell down on one end causing employee to fall.

While manually handling railroad tie w/tic tongs to position for placement, EE felt pain in his lower back and groin.

EE LIFTED A LID TO RETRIEVE A GREASE LINE AND LID FELL ON LEFT HAND

EE WAS STANDING ON DRAGLINE BOOM BOX ARC GOUGING. MOLTEN METAL TRAVELED DOWN RIGHT LEG AND SETTLED IN RIGHT BOOT BURNING RIGHT FOOT.

EE WAS ASSISTING WITH THE INSTALLATION OF THE PLANETARY OF A SCRAPER. WHILE MANEUVERING THE PLANETARY, AN EYE BOLT THAT WAS BEING USED TO ATTACHTHE RIGGING BROKE. THIS CAUSED THE PLANETARY TO FALL AND STRIKE THE EE. EE WAS STRUCK ON THE RIGHT SIDE OF BODY IN THE BACK, HIP, KNEE, AND CHEEK.

EE WAS CLEANING THE TOP OF THE MACHINE HOUSE ON THE CROSS PIT SPREADER. IT HAD BEEN RAINING & THE AREA WAS SLICK. HIS FOOT SLIPPED OUT FROM UNDER HIM & HE FELL. HE FELL FORWARD & ATTEMPTED TO BREAK THE FALL WITH HIS HAND. THIS RESULTED IN A DISLOCATION OF HIS LEFT THUMB. THE THUMB WAS PUT BACK INTO PLACE AT THE E.R. & SPLINTED.

EE WAS ASSISTING WITH A DRAG ROPE CHANGE. WHILE IN THE PROCESS OF ROUTING THE ROPE THROUGH A SOCKET, THE ROPE BECAME STUCK. EE STRUCK THE ROPE WITH A FIVE FT PRY BAR, THE ROPE DISLODGED AND STRUCK HIM ON HIS LEFT ANKLE. THIS RESULTED IN AFRACTURE.

EE WAS HOOKING UP A HOSE TO THE STEAM CLEANER INTHE SHOP. AS THE LID OF THE STEAM CLEANER BEING LIFTED, IT FOLDED UNDER. THE EE MIDDLE FINGER ON HIS LEFT HAND WAS STRUCK ON THE MIDDLE JOINT. THIS RESULTED IN A LACERATION THAT REQUIRED STITCHES.

EE WAS WALKING TO A BARGE PUMP & TRIPPED OVER A CLOD OF DIRT. THIS RESULTED IN A SORE ANKLE. EE CONTINUED TO WORK WITHOUT RESTRICTION. HE WAS EXAMINED BY A DR. WHO FOUND NO PROBLEM. EE CONTINU ED TO REPORT SORENESS IN HIS ANKLE & WAS SEEN BY A SPECIALIST ON 10/24/03. NO TEARS OR FRACTURESWERE NOTED ON X-RAYS OR ON MRI. WE WERE NOTIFIED TODAY THAT EE IS RECEIVING P.T. NOW REPORTABLE

EMPLOYEE WAS WELDING PLATE ON BUCKET. WHILE LIFTING A PIECE OF METAL IT DROPPED MASHING HIS FINGER. THIS RESULTED IN APPROX 1 1/4" LACERATION TO HIS THUMB.

AN ACCIDENT OCCURRED WHEN EMPLOYEE'S WERE TRAVELING SOUTH FROM THE G AREA IN A 1996 GMC 4 WHEEL DRIVE PICKUP. THE DRIVER WAS SPEEDING AND LOST CONTROL OF TRUCK AND ROLLED OVER INTO THE DRAINAG E DITCH. THIS ACCIDENT OCCURRED DUE TO CARELESS AND RECKLESS OPERATIONS OF A MOTOR VEHICLE. BOTH OF THE EMPLOYEE'S WERE INJURED.

AN ACCIDENT OCCURRED WHEN EMPLOYEE'S WERE TRAVELING SOUTH FROM THE G AREA IN A 1996 GMC 4 WHEEL DRIVE PICKUP. THE DRIVER WAS SPEEDING AND LOST CONTROL OF TRUCK AND ROLLED OVER INTO THE DRAINAG E DITCH. THIS ACCIDENT OCCURRED DUE TO CARELESS AND RECKLESS OPERATIONS OF A MOTOR VEHICLE. BOTH OF THE EMPLOYEE'S WERE INJURED.

PULLING 7" BY 24" BY 1" PLATE STEEL FROM UNDERNEATH BUGIES. DROPPED 1 PIECE ON LEFT HAND FINGER, LACERATING RING FINGER.

EE REPORTED PAIN IN HIS LOWER BACK AFTER OPERATING A FRONT END LOADER.

EE WAS PERFORMING MAINTENANCE ON THE BUCKET WHEEL EXCAVATOR WHEN HE FELT PAIN IN THE BACK OF HIS NECK.

EMPLOYEE REPORTED PAIN IN RIGHT ELBOW AFTER PERFORMING NORMAL MAINTENANCE DUTIES. EE CONTINUED TO PERFORM ALL ASPECTS OF HIS JOB UNTIL 12-2-02. AT THAT TIME, A PHYSICIAN DIAGNOSED THE PAIN AS BEING CAUSED BY TENDONITIS. HE WAS PLACED ON RESTRICTIVE DUTY AT THIS TIME.

EE WAS ASSISTING CHANGING ROLLERS ON AN HITACHI BACKHOE. THE #3 ROLLER WAS SET IN PLACE & A BOLT WAS STARTED TO SECURE IT. THE EMPLOYEES BEGAN TO RELEASE THE PRESSURE ON THE ROLLER & THE BOLT DID NOT HOLD. THE ROLLER DROPPED DOWN ON THE EE'S LEFT HAND & PINCHED IT BETWEEN THE ROLLER & AN IMPACT WRENCH. THIS RESULTED IN A 1" LACERATION TO THE LEFT INDEX FINGER.

EMPLOYEE WAS OPERATING A SCRAPER WHEN IT JACKKNIFED AND SLID INTO A DITCH. RAIN, SLICK ROADS AND DARKNESS WERE CONTRIBUTING FACTORS. THE EMPLOYEE STRUCK HIS HEAD ON THE STEERING WHEEL DURING T HE ACCIDENT.

EE WAS ASSISTING WITH A BELT CHANGE ON THE CROSS PIT SPREADER. HE TRIPPED & FELL WHILE TRAVELING DOWN THE WALKWAY & CRACKED A BONE IN HIS RIGHT ARM, DETERMINED BY A POSITIVE X-RAY. NO SPLINT O R CAST WAS APPLIED AND HE WAS ABLE TO RETURN TO WORK AND PERFORM REGULAR DUTIES.

EE WAS ATTEMPTING TO REMOVE A BOLT WHEN THE WRENCH SLIPPED. EE STRUCK RIGHT HAND ON A PIECE OF METAL. THIS RESULTED IN A LACERATION THAT REQUIRED 6 SUTURES TO CLOSE.

EMPLOYEE WAS CHANGING THE FUEL PUMP ON A COAL HAULER. HE STEPPED UP ON A LADDER WHICH WAS UNDER THE HAULER IN ORDER TO REACH THE FUEL PUMP. AS HE STEPPED UP HE STRUCK HIS HEAD ON THE AIR FILTE R BRACKET.

EMPLOYEE REPORTED WEAKNESS AND PAIN IN BOTH WRISTS. EMPLOYEE WAS SEEN BY A PHYSICIAN WHO PERFORMED NERVE FUNCTION TESTS. BASED ON THE RESULTS OF THOSE TESTS, THE PHYSICIAN WHO DIAGNOSED THE PAIN AS CARPAL TUNNEL SUNDROME. EMPLOYEE WAS STILL ABLE TO PERFORM ALL ASPECTS OF HIS JOB UNTIL 2-14-02 WHEN HE UNDERWENT SURGERY ON HIS RIGHT WRIST.

EMPLOYEE WAS REMOVING A HOIST BRAKE AIR CYLINDER FROM A DRAGLINE. AS THE CYLINDER WAS BEING LOWERED, THE CYLINDER HOUSING FELL, STRIKING EE ON THE LEFT HAND. HE WAS TAKEN TO SEE HIS PERSONAL P HYSICIAN ON DECEMBER 31, 2001. X-RAYS WERE TAKEN AND THEY WERE NEGATIVE. ON JANUARY 28, 2002 AN MRI WAS TAKEN DUE TO CONTINUED SWELLING IN THE HAND. THE RESULTS REVEALED A CRACKED BONE.

EE WAS ATTEMPTING TO HAMMER A TOOTH RETENTION PIN INTO PLACE ON A DRAGLINE BUCKET WHEN HE MISSEDTHE PIN STRIKING HIS LEFT THUMB. THIS RESULTED IN A LACERATION REQUIRING SUTURES.

EE WAS GRINDING AND A FOREIGN OBJECT GOT INTO HIS LEFT EYE.

EE WAS WALKING DOWN A FLIGHT OF STAIRS WHEN FELT PAIN IN HIS LEFT KNEE. EE WAS EXAMINED BY A DOCTOR ON JUNE 11TH, WHO DIAGNOSED THE INJURY AS A TORN LIGAMENT.

EE REPORTED PAIN IN BOTH WRISTS AFTER PERFORMING REPAIRS IN THE MAINTENANCE SHOP. VARIOUS TYPES OF TOOLS WERE USED. WAS SEEN BY A PHYSICIAN WHO DIAGNOSED THE PAIN AS CARPAL TUNNEL SYNDROME. EE IS STILL ABLE TO PERFORM ALL ASPECTS OF HIS JOBAT THIS TIME AND IS TAKING PRESCRIPTION MEDICATION FOR PAIN.

EE WAS ATTEMPTING TO REMOVE A PULLEY FROM A SHAFT WHEN HE STRUCK HIS LEFT HAND WITH A HAMMER. THIS RESULTED IN A LACERATION REQUIRING SUTURES.

EE WAS MOVING A PLATE INTO POSITION APPROX 2" X 18" X 32". PLATE BECAME OVER BALANCED AND FELL TO ONE SIDE CATCHING HIS RIGHT HAND BETWEEN THE PLATE AND FLOOR.

BOOM FAILURE ON THE CROSS PIT SPREADER CAUSED GLASS IN OPERATOR'S CAB TO BREAK. PIECE OF BROKEN GLASS WAS EMBEDDED IN EMPLOYEE'S RIGHT ELBOW.

EE WAS REMOVING A DAMAGED STEP FROM THE REAR OF A FRONT END LOADER. WHEN HE REMOVED THE LAST TWO BOLTS, IT FELL APPROX FOUR FEET WHILE HE WAS HOLDING IT. THIS RESULTED IN A TORN ROTATOR CUFF I N HIS RIGHT SHOULDER.

EE WAS WORKING AT THE BUCKET WHEEL EXCAVATOR. WHILE MOVING FROM ONE WORK LOCATION TO THE NEXT, HE HYPER-EXTENDED HIS RIGHT KNEE.

EMPLOYEE WAS DESCENDING STAIRS AT THE CRUSHER. AS HE STEPPED DOWN TO GROUND LEVEL, HE TRIPPED ON A PIECE OF COAL AND TURNED HIS ANKLE. THIS RESULTED IN A SPRAIN TO HIS RIGHT ANKLE.

AN EQUIPMENT REPAIR CONTRACTOR WAS INSTALLING A BUSHING ON A HAULER. CONTRACTOR STRUCK THE BUSHING WITH A HAMMER. A SMALL PIECE OF METAL BROKE OFF AND STRUCK A TXU EMPLOYEE. A SLIVER OF MET AL (1/4"X 1/16") AND SEVERAL SMALL FRAGMENTS HAD TO BE EXTRACTED BY A DR. ONE STITCH WAS RQUIRED DUE TO THE EXTRACTION INCISION.

WHILE REPAIRING TUB HOOK ON D-22 EE'S RIGHT EYE BEGAN TO ITCH. THE NEXT MORNING WHEN HE TRIED TO SEE WHAT WAS CAUSING THE ITCH, THE WORSE IT GOT. THE DOCTOR REMOVED A FOREIGN OBJECT FROM HIS E YE.

EE WAS INSTALLING FROZEN BUSHING INTO BORE. SLEEVE BECAME STUCK. WHILE EE WAS TRYING TO REMOVE SLEEVE, BACK END RESTED OF HIS LEFT ARM BETWEEN HIS WRIST AND ELBOW CAUSING A 2ND DEGREE BURN.

EE WAS USING 1/2" IMPACT WRENCH WITH SWIVEL JOINT TO REMOVE DRIVE LINE BOLTS. THE UNIVERSAL JOINT BROKE AND CUT HIS FINGER.

EE WAS IN MSHA RETRAINING AND FEL PAIN IN HIS LOWER BACK WHEN HE AND TWO OTHERS WERE LIFTING TRAINING MANNEQUIN AT #6 STATION ON TUESDAY.

EE STRAINED HIS BACK WHILE MOVING CROSS-TIES AT DRAGLINE.

WHILE MOVING DRAGLINE HOIST CHAIN LINKS OFF THE BED OF A MAINTENANCE TRUCK ONE OF THE LINES FELLBACK ON THE EE'S RIGHT HAND

THE EMPLOYEE FELL DOWN 6 STEPS AT THE CROSSPIT SPREADER BREAKING 2 BONES IN HIS RIGHT ANKLE.

EMPLOYEE WAS CHANGING CUTTING EDGES ON D9 DOZER.WHILE PUTTING A JACK STAND UNDER TRUNION ARM TO BLOCK MOVEMENT OF BLADE, THE STAND RELEASED MASHING LEFT LITTLE FINGER REQUIRING 6 STITCHES.

EE WAS TROUBLE SHOTING #1 LAKE PUMP BREAKER. HE WAS TESTING FOR VOLTAGE AND TOUCHED THE B PHAS WHEN IT TRACKED ACROSS ANOTHGER PHASE CAUSING A FLASH, KNOCKING HIM BACKWARDS INTO A WATER PIPE A ND BRACKT SUPPORT.

EMPLOYEE WAS TURNING OVER CUTTING EDGES ON 992D RUBBER TIRED DOZER, USING 1" IMPACT WRENCH WHEN METAL SHAVINGS GOT IN HIS LEFT EYE.

WHILE REPAIR WORK WAS DONE ON THE #1 CONVEYOR (CUTTING AND WELDING) SPARKS APPARENTLY STARTED SOME LIGNIT DUST TO SMOLDER UNTIL IT FINALLY IGNITED AND BURNED THE ENTIRE CONVEYOR BELT. NO PERSO NNEL WAS PRESENT WHEN FIRE STARTED AND DID NOT DISCOVER THE FIRE BEFORE IT HAD NEARLY BURNED COMPLETELY. THERE WERE NO INJURIES DUE TO THIS INCIDENT.

EE WAS REPLACING VALVE ON WATER CANNON AT THE WASH RACK. HE BECAME NAUSEOUS AND STARTED VOMITING. ABOUT 1:30 HE HAD CHILLS AND WAS WEAK.

WHILE CHANGING FAIRLEAD TIRES ON D-22, EMPLOYEE WAS STANDING ON FAIRLEADS, GUIDING THE TIRE PIN INTO HOLES. THE PIN DIDN'T LINE UP CORRECTLY SO HE WAS ATTEMPTING TO ALIGN PIN WITH HIS HAND. IT FELL THROUGH THE HOLES AND CAUGHT HIS LEFT RING FINGER BETWEEN PIN AND PIN BRACKET, MASHING HIS FINGER REQUIRING SUTURES.

EE WAS REMOVING THE WATER PUMP ON 28050 IT28 FORKLIFT. AS THE PUMP CAME OUT OF THE HOLR IT FELL DOWN ON TOP OF EE'S LEFT HAND. THE PULLEY HAD A SHARP EDGE ON IT WHICH CUT HIS MIDDLE FINGER.

EMPLOYEE WAS TRYING TO PULL SLUSH PIT AND PULLEDRIGHT SHOULDER MUSCLE.

EE WAS SMOTHING THE HIGHWALL SIDE OF THE PIT FOR THE HAULERS WHEN A LARGE SECTION OF THE HIGHWALL FELL ON THE DOZER HE WAS OPERATING. EE RECEIVED A COMPRESSION INJURY TO THE 4TH AND 5TH VERTEB RAS.

EE WAS THROWING A DRAGLINE CABLE SHOE ONTO THE BACK OF 25415 PUMP TRUCK. THE SHOE WEIGHS ABOUT 20 PDS. THE CABLE SHOE HAD A 6FT PIECE OF CHAIN ON IT. THE CHAIN CAUGHT ON THE HITCH AREA AT THE REAR OF THE TRUCK MAKING THE SHOE TO COME BACK &DOWN, CATCHING HIS RIGHT INDEX FINGER BETWEEN TRUCK BED & SHOE

EE WAS INSTALLING NEW FEEDER CHAINS ON #1 FEEDERTHE CHAINS WERE NOT TIMED PROPERLY SO A COMEALONG WAS HOOKED UP TO ROLL THE CHAIN AROUND SO IT WOULD BE EVEN WITH TOTHER CHAIN. THE CHAIN DIDN 'T MOVE AS EASY AS IT SHOULD HAVE AND THE HOOK OF THE COMEALONG CAME OFF, HITTING EE ON UPPER LIP & RIGHT EYE BROW

D-22 HAD TRIPPED AND THERE WAS A FLASH AND SMOKE IN THE DC RM AND THE ROTATION LIGHT WAS OUT. EE WENT DOWN AND NOTICED BURNT WIRES AROUND ACB BREAKERS 1 &2. HE CALLED FOR ASSISTANCE AND TO BRI NG WIRE AND PRINTS. HE STARTED TRACING THE BURNTWIRES WHEN IT FLASHED UP IN FRONT OF HIS FACE, BURNING THE RIGHT SIDE OF HIS FACE, RIGHT EAR, FOREHEAD, NOSE, NECK AND BOTH HANDS.

HE WAS DROPPING OUT A ROLLER ON RECEIVING BELT OF BWE AND GOT HIS FINGERS ON HIS RIGHT HAND MASHED BY THE BELL LOOP ON THE ROLLER. HIS FINGERS GOT CAUGHT BETWEEN BELL LOOP AND PEG ON WIND GUAR D. HE MASHED 2ND AND 3RD FINGERS OF RIGHT HAND.

EE WAS REINSTALLING THE TRACK ON 21106 DOZER. A 1/4" CHAIN WAS HOOKED TO THE TRACK RAILS. A SECOND 1/4" CHAIN WAS HOOKED INTO THE FIRST CHAIN AND WRAPPED AROUND THE DOZER FINAL DRIVE. THE DOZE R FINAL DRIVE WAS PULLING THE TRACK UNDERNEATH THE DOZER ROLLERS AND INTO POSITION. THE TRACK GOT HUNG ON A ROLLER, CAUSING THE FIRST CHAIN TO RREAK AND SECOND CHAIN WHIPPED BACK AND THE HOOK

EE WAS OPERATING 21099 DOZDR, RIPPING PARTING FOR SCRAPERS. WHEN BACKING HIS DOZER, HE RAN OVER A LARGE PIECE OF PARTING WHICH CAUSED HIM TO TWIST & INJURE HIS BACK.

EE WAS WORKING IN TOOLROOM. HE SLIPPED ON TOOL ROOM FLOOR DUE TO A MUDDY FLOOR. BACK OF LEFT HAND HIT AN OPEN ROD BOX & LACERATED BACK OF HAND.

EE WAS WELDING BESIDE ANOTHER EE WHEN A WELDING BUCKSHOT WENT IN BEHIND THE WELDING HOOD AND SAFETY GLASSES INTO LEFT EYE.

EMPLOYEE WAS WORKING ON LOOSE CABLE ON THE POSITIVE TERMINAL OF A TRUCK BATTERY. WHEN HE PUT HIS RATCHET ON THE TERMINAL BOLT, THE BATTERY EXPLODED RESULTING TO AN INJURY TO HIS FACE.

EE STEPPED OFF A TRAILER INTO A HOLE & ROLLED HIS FOOT SIDEWAYS

EMPLLOYEE BENT DOWN TO PICK UP POWER CABLE ADN FELT A SHARP PAIN IN LEFT KNEE.

DROPPED METAL PLATE, CAUGHT END OF RIGHT THUMB.

EMP WALKING ON GRATING OUTSIDE TOOLROOM. STEPPED OFF INTO MUD AND SLIPPED.

ANOTHER EMP WAS GOUGING AND A PIECE OF AIRBORNE METAL LODGED IN RIGHT EYE.

HE WAS HELPING REPLACE A CABLE ON A 30-B DRAGLINE. HE BENT DOWN TO PICK THE CABLE UP AND DIDN'T GET IT OFF THE GROUND, WHEN HE FELT A SEVERE PAIN IN HIS BACK.

EMP WAS CHANGING OUT DRAGLINE TEETH ON D-22, USING A SLEDGE HAMMER AND A B&O HAMMER. WHILE STRIKING THE PINS TO REMOVE THE TEETH, A PIECE OF METAL FLEW OFF AND STUCK IN FOREARM AND HAD TO BE S URGICALLY REMOVED.

EMPLOYEE WAS USING A DIE GRINDER TO CLEAN RUST FROM SHRINK DISK PARTS WHEN THE EXHAUST FROM THE GRINDER BLEW SOME PARTICLES IN HIS LEFT EYE.

EMPLOYEE WAS FUELING MOTORGRADER. WHEN HE TURNEDTO PUT FUEL NOZZLE AWAY HE FELT PAIN IN LOWER BACK.

EE WAS MANHANDLING THE DRAGLINE POWER CABLE OUT OF THE CABLE HSOE WHEN HE FELT HIS LEG STINGING.

EMP WAS WELDING STAINLESS STEEL IN TRANS HOPPER WEAR BARS ON BWE, WHILE CHIPPING SLAG FROM HOT WELD, A PIECE OF SLAG BOUNCED IN FROM REAR OF HOOD AND FELL BEHIND SAFETY GLASS AND LANDED IN LEF T INSIDE CORNER OF EYE,BURNING LFT CORNER OF EYE

EMPLOYEE WAS REMOVING THE RIPPER TILT CYLINDER FROM THE BACK OF 21099 DOZER. HE WAS USING A 3 FOOT BAR TO KNOCK THE PIN OUT. WHEN THE PIN CAME OUT, IT MASHED EMPLOYEE'S THUMB AND HAND BETWEEN THE BAR AND THE TRACK.

EMPLOYEE WAS IN PROCESS OF REMOVING DRAG CHAIN PEAR LINK FROM DRAG SHACKLE. THE DRAG SHACKLE WAS BEING HELD UP BY A NYLON STRAP ATTACHED TO FORKS OF FORKLIFT. THE PEAR LINK WAS OFF THE GROUND A LITTLE. INJURED WAS WORKING THE PEAR LINK OFF,HE PULLED ON IT PRETTY HARD. HE FELT A SHARP PAIN IN HIS LOWER BACK.

BULLDOZER ROLLER MASHED THUMB HAND CHANGING BULLDOZER ROLLER.

EE WAS DRAGGING A 20' CHAIN AND SQUATTED UNDER A DOZER RIPPER TO WRAP CHAIN AROUND TOOTH. AS HE SQUATTE DOWN, HE FELT A STINGE IN THE MIDDLE OF HIS BACK.

EE WAS GRINDING INSIDE THE REVOLVING FRAME. EE LAID THE GRINDER DOWN AND WAS ATTEMPTING TO STAND AND ACCIDENTLY TURNED THE GRINDER ON, PUTTING A 1 1/2" CUT ON BACK OF LEFT HAND.

INJURED GOT A FOREIGN OBJECT IN HIS LEFT EYE.THE BRASS WAS REMOVED ON SITE.BEFORE THE OBJECT WAS REMOVED HE HAD RUBBED HIS EYE CAUSING SCARRING.

EMPLOYEE WAS GOUGING ON A LEG,REPAIRING CRACKS.EMPLOYEE WAS ALSO GRINDING.A PIECE OF TRASH GOT BEHIND WELDING HOOD AND INSIDE SAFETY GLASSES.

EMP WAS REMOVING THE LOWER INTER, CARRIER HOUSING AND BEARING WHICH WEIGHS ABOUT 150 LBS. HE WAS USING A 5'BAR AND A CROSS-TIE BLOCK FOR LEVERAGE. TWO EMP'S WERE USING A HAMMER TO TAP THE HOUS ING FROM CARRIER WHEN THE CARRRIER AND BEARING CAME OUT, CAUSING THE CARRIER TO FALL 6 INCHES ON THE BAR, MASHING EMP MIDDLE AND INDEX FINGER OF RT HAND BETWEEN FLOOR AND 5' BAR.

EE WAS REPAIRING THE TUBE OF A DRAGLINE BUCKET INSIDE THE BUCKET HOUSE. WELDING & GRINDING WAS BEING PERFORMED IN THE USUAL MANNER. IT WAS A VERY WINDY DAY & EE STATED HE REALLY DIDN'T KNOW WH EN THE PIECE OF METAL ENTERED HIS EYE. IT DIDN'TSTART TO BOTHER HIM UNTIL LATER THAT NIGHT.

WHILE REPLACING THE MAIN SUSPENSION LINES ON THE DRAGLINE I WAS UNSPOOLING THE LINES OFF OF THE CABLE REEL. IT WAS AFTER DARK. I WAS TURNING THE SOCKETS OF THE LINES WHILE THEY WERE SUSPENDED BY THE CRANE AND PINCHED MY MIDDLE FINGER BETWEEN THE SOCKET AND THE SPOOL PIPE.

THE WINCH ON THE BARGE PUMP THE EMPLOYEE WAS WORKING ON WAS TIED UP WITH A PIECE OF ROPE. WHEN HE UNTIED THE ROPE HE REACHED FOR THE HANDLE ON THE WINCH AND BEFORE HE COULD GET TO IT THE WINC H STARTED UNWINDING ON ITS OWN AND HE TRIED OT GRAB IT. THE HANDLE HIT HIS FINGER AND CUT IT.

EE WAS INSTALLNG INJECTOR BANK ON INSIDE OF DRIVE SPROCKET ON RIGHT TRACK. HE WA SON HIS HANDS AND KNEES AT THE FIRST SET BEHIND THE DRIVE SPROCKET. THERE WAS A GROUP OF PEOPLE WORKING ABOVE ON HE OUTSIDE OF THE DRIVE SPROCKE.T A FOUR POUND HAMMERR FELL APPROX 12 TO 15', STRIKING E IN LOWER BACK.

EMPLOYEE JUMPED OFF BACKHOE JARRED BACK AND HIPS.MARCH 27,PIACKED UP TRAILER,DID NOT BOTHER EMPLOYEE.MARCH 31,1995 PICKED UP TRAILER HURT BACK.

PUMPERS WERE CHECKING A BARGE PUMP IN G-1 PIT THEY WERE APPROX 120FT NORTH OF H-24 (BACK HOE) WHICH WAS LOADING PARTING THE RT WINDOW OF THE PUMP TRUCK THEY WERE IN WAS ROLLED DOWN SO THEY COU LD SHINE A SPOT LIGHT & SEE THE DISCHARGE LINE SOME DUST BLEW IN EE EYE WHEN THE BACXKHOE DUMPED A BUCKET IN THE END DUMP

EMPLOYEE WAS UNPLUGING 480 VOLT HEATER WHEN TWO CORDS WENT TOGETHER INSIDE THE PLUG CAUSING AN ARC, WHICH CAUSED THE EMPLOYEE TO JUMP BACK. THE ARC SINGED THE TOP OF HIS HAND.

ACCIDENT OCCURRED WHILE REMOVING OLD CARRIER ROLLER ON DISCHARGE BELT. CARRIER ROLLER WAS UNLATCHED ON BOTH ENDS. BOOM TRUCK WAS HOOKED TO ONE END TO PULL OUT FROM UNDER CONVEYOR BELT. ROLL ER HUNG UP ON BRACES. EMPLOYEE WAS UNDER BELT GUILDING ROLLER AND WHEN ROLLER MOVED, THE LATCH FLIPPED OVER THE END, PINCHING EMPLOYEE'S INDEX FIGNER ON RIGHT HAND.

EE WAS STEPPING OUT OF HOLE BETWEEN THE RACK & ROLLERS WHEN CLOTHING CAUGHT ON UNISTRUT, CAUSING HIM TO FALL ON CORNER OF MANWAY DOOR CUTTING HIS RIGHT ARM.

EE WAS OPERATING 22016 HAULER, HAULING COAL OUT OF THE WEST END OF THE PIT WHEN THE HAULER UPSHIFTED, CAUSING A JERK IN HIS BACK.

EMPLOYEE WAS BACKING DOZER IN PIT WHEN HE BACKED OVER THE COAL EDGE (DROPPED OFF APPROX 1 FT) HURTING HIS LOWER BACK

EMPLOYEE WAS STANDING ON LADDER ON FUEL TANK WHILE FUELING 22031 HAULER ON EAST SIDE OF LUBE DOCK HE TURNED & REACHED FOR PLATFORM ON DOCK TO PULL IT DOWN HE SLIPPED OFF STEP ON LADDER GRABB ED FOR HANDRAIL ON LUBE DOCK & WRIST SLIPPED DOWN BETWEEN PLATFORM & HANDRAIL AS HE WAS FALLING INSIDE LOWER PART OF ELBOW HIT BOTTOM OF PLATFORM RESULTING IN BRUISED RT WRIST & ELBOW WAS FRAC

WHILE CLEANING UP AROUND CRUSHER, A THUNDERSTORM BLEW IN, BLOWING DEBRIS AND SOME GOT IN HIS EYE.

EE WAS CLEANING OUT OIL DRAIN PAN WHEN HE FELT PAIN IN HIS LOWER BACK.

WHILE EE WAS PULLING TRAIL CABLE, EE TRIPPED OVER A CABLE SHOE, WHICH WAS IN THE SHADOW OF A JUNCTION BOX.

EE WENT INTO REVOLVING FRAME COMPARTMENT TO LOCATE SOURCE OF GAS LEAK. HE CAME BACK NITE TURNED OFF BOTTLE CONNECTED THAT HOSE.

TWO MEN WELDING IN SAME COMPARTMENT. GRINDINGING PARTICLE BLEW INTO EYE. WASHED OUT EYE ON SITE BUT SOME PARTICLE MISSED.

WHILE ATTEMPTING TO LOOSEN A DOUBLE NUTTED BOLT, THEEMPLOYEE WAS USING A 12 INCH CRESCENT WRENCH, APPLYING HIS WEIGHT. THE NUTS BROKE LOOSE CAUSING HIM TO MOVE FORWARD SUDDENLY AND HIT HIS LO WER LIP ON THE NUT AND CUT HIS LIP.

EMPLOYEE WAS UNLOADING A TINHORN OFF A TRAILER. ONE END OF THE TINHORN WAS ON THE GROUND AND THE OTHER END ON THE TRAILER. HE WAS AT THE HIGHER END AND TRYING TO BOUNCE IT OVER THE BLOCK ON TH E TRAILER. THE TINHORN WAS 40 FT LONG.

EMPLOYEE WAS USING A COME-A-LONG, PULLING A SHAFT OUT OF THE BUCKET WHEEL EXCAVATOR WHEN THE CHAIN BROKE AND HIT THE EMLOYEE ON HIS SAFETY GLASSES, SCRATCHING HIS EYE.

EMPLOYEE WAS MANUALLY LIFTING MATERIAL & REPORTED BACK STRAIN FROM OVER EXERTION

EMPLOYEE WAS HOOKING UP WINCH LINE ON A STUCK HAULER & FELT A PAIN IN HIS BACK.

EE WAS STANDING ON BARGE PUMP, HOLDING DOWN PRIMING VALVE AND HE NOTICED A BURNING IN LOWER RIGHT SIDE OF BACK. HE HAD HELPED TO MOVE A BOAT PRIOR TO THIS PAIN IN HIS BACK. LATER AT HOME WHILE SHOERING HE EXPERIENCED MORE PAIN IN HIS LOWER BACK, RIGHT SIDE, WITH A PAIN GOING DOWN LEG TO GROIN AREA. HE HAD STRAINED LIGAMENTS IN HIS LOWER BACK.

EMPLOYEE TWISTED HIS LEFT KNEE AS HE STEPPED OFF OF DOZER ONTO SMALL CLOD ON GROUND. LIGHT DUTY DID NOT BEGIN UNTIL 2-21-94.

EE WAS PUSHING DIRT ON SPOIL SIDE WALKWAY WEST OF RAMP H-3 ON 21093 DOZER. AT THE END OF THE SHIFT THE EE WENT TO HIS FOREMAN AND TOLD HIM THAT THE SEAT IN 21093 DOZER HAD MADE HIS BACK SORE.

EMPLOYEE WAS TAKING THE TOP RETAINER PLATE OFF OF THE INTERMEDIATE SHAFT OF #2 SWING GEAR CASE.HE WAS SUING A 3/4 " END WRENCH TO REMOVE 1/2" BOLTS WHEN ONE SLIPPED CAUSING HIS RIGHT ELBOW TO STRIKE THE GEAR CASE.

EMPLOYEE WAS MOVING CABLE SO WALKWAY COULD BE MUCKED OFF. CABLE SHOE, ELECTRICAL GLOVES, POWER CABLE. WHILE MOVING CABLE SHOE TO DIFFERENT LOCATION TO MOVE CABLE SO THE REST OF THE WALKWAY COU LD BE MUCKED OFF, HE FELT PAIN IN LOWER BACK ANDBURNING IN LEFT HIP AND LEG.

THE EMPLOYEE WAS HOLDING A 4 X 4 WOODEN BLOCK ACROSS A BUSHING AS NOT TO DAMAGE IT, WHEN INSTALLING IT. WHEN ANOTHER EMPLOYEE STRUCK THE BLOCK WITH THE 16 POUND SLEDGE HAMMER, IT GLANCED OFF AND HIT THE EMPLOYEE HOLDING THE BLOCK IN THE MOUTH.

EMPLOYEE SHUT DOOR OF DOZER ON LITTLE FINGER OF RIGHT HAND, CUTTING HIS FINGER.

EMPLOYEE WAS WALKING ACROSS SHOP FLOOR CARRYING A WATER HOSE. THE FLOOR WAS SLIGHTLY WET. THE EMPLOYEE SLIPPED AND FELL, INJURING HIS RIGHT LEG.

EMPLOYEE WAS PULLING DIFFERENTIAL OUT OF 22027 HAUL TRUCK. HE PULLED A BLUE METAL LADDER BETWEEN TRACTOR AND TRAILER AND HAD ONE FOOT ON FOURTH STEP OF LADDER AND OTHER FOOT ON DIFFERENTIAL H OUSING. THE LADDER SLIPED OUT FROM UNDER HIM. HE FELL ABOUT FIVE FEET TO THE FLOOR, LANDING ON HIS LEFT SIDE. WHEN HE HIT THE FLOOR THE 3 FOPOT PRY BAR HIT HIS SAFETY GLASSES, CUTTING THE L

EMPLOYEE WAS DRIVING A MASSEY FERGUSON TRACTOR DOWN A SLOPE WHEN HE HIT A ROUGH SPOT. THIS CAUSED THE EMPLOYEE TO HIT HIS CHIN ON THE STEERING WHEEL.

EMPLOYEE WAS INSTALLING EQUALIZER BAR PADS BETWEEN THE MAIN FRAME AND THE EQUALIZING BAR ON BOTH SIDES. A PORTA-POWER WAS SITTING ON TOP OF THE RIGHT SIDE OF EQUALIZER BAR, PUSHING AGAINST MAI N FRAME OT MAKE ROOM FOR THE PAD. APPARENTLY THE PORTA-POWER SLIPPED, SHOOTING THE SHIM OUT CUTTING THE EDN OF THE LEFT HAND LITTLE FINGER OFF JUST BELOW FINGER NAIL.

WASHING GOOSENECK AREA BEHIND CAB STANDING ON NON-SKID TAPE ON FENDER. AS INJURED STEPPED FROM FRNDER TO FIRST STEP HE SLIPPED & FELL TO THE FLOOR. RIGHT ARM STRUCK FLOOR. BROKE RADIUS & UNLNA IN RT. ARM. IN CAST FOR 4 WKS. FROM WRIST TO SIX INCHES DOWN FOREMAN.

EMPLOYEE WAS MAKING AN AIR WHIP HOSE.

EMPLOYEE WAS USING AN IMPACT WRENCH TO SECURE DRAG ROPES TO DRAG DRUM WHEN METAL SHAVING ENTERED HIS EYE.

EMPLOYEE WAS ON HIS WAY DOWN DOME STAIRS WHEN HIS RIGHT KNEE POPPED.

EMPLOYEE WAS CLIMBING LADDER TO TIE OFF WITH ROPE, WHEN HE SLIPPED ON A MUDDY LADDER. RUNG CAUSING HIM TO FALL APPROX. 5 FT LANDING ON ANKLE. WEATER CONDITIONS WERE VERY WET AND MUDDY.

EE WAS EMPTYING GREASE BARRELS AND GOT HIS HAND CAUGHT BETWEEN TWO BARRELS.

EE WAS WASHING EQUIPMENT IN THE WASH SOMETHING GOT INTO HIS EYE. HE DID NOT DETECT THE OBJECT ONLY THAT HIS LEFT EYE WAS ABNORMALLY RED.

EE WAS HAULING SHELL FROM THE D/L CUT UP THE RAMP TO PATCH HOLES IN RAMP AND RAISE LOW AREAS. THE RAMP WAS BEAT OUT AT THE CAL EDGE AND WHEN THE LOADER BACKED ACROSS ONE OF THE LOW AREAS AND H IT THE COAL EDGE THE SEAT WOULD NOT ADJUST TO THE MUSCLE IN HIS NECK.

EMPL HAD STOPPED DOZER TO TAKE A BREAK. STEPPED OUTSIDE CAB TO GET LUNCH BOX. UPON REENTERING CAB LOST FOOTING AND FELL OFF DOZER ONTO GROUND. BOTH LEGS HIT TRUNION ARM ON THE WAY DOWN RESULTI NG IN A CUT BELOW RIGHT KNEE REQUIRING 5 STITCHES AND BRUISES ON BOTH LEGS.

EMPLOYEE STATED HE DEVELOPED A HEADACHE AFTER WELDING FOR APPROX TWO HOURS INTO THE SHIFT EMPLOYEE THOUGHT VENTILA TION WEAS INSUFFICIENT EMPLOYEE GOT SICK AT HIS STOMACH & HAD DRY HEAVS EMPLO YEE WAS SEN T TO DOC & RETURN TO WORK NO IMPAIRMENT & ENVIRONMENTAL TEST RESULTS ARE NOT AVAILABLE AT THIS TIME

HELPER WAS USING PRY BAR ON CAM ROLLERS AND STATES THAT PRY BAR SLIPPED AND STRUCK MOUTH.

WELDER WAS USING WRENCH TO LO0SEN FITTINGS AND STATES THAT WRENCH SLIPPED AND STRUCK MOUTH.

EMPL DOESNT REMEMBER WHAT HE WAS DOING OR HOW HURT. DOESNT REMEMBER SLIPPING OR FALLING,ASSUME EMPL BLACKED OUT AND THEN FELL DOWN. NO WITNESS,CANNOT DETERMINE WHERE EMPL FELL. EMPL LEFT ELBO W SCRAPED.LEFT SIDE OF BACK HAVING MUSCLE SPASMS. HEAD BRUISED BETWEEN EYES WHERE SAFETY GLASSES HIT.

EMPLOYEE HAD JUST FINISHED WASHING THE WEST END OF THE WASH BUILDING AND WAS WALKING TOWARD THE EAST END WHEN HE STEPPED ON SOME GRATING.IT TURNED,CAUSING TO TO FLIP,AND THE EMPLOYEE FELL INTO DRAIN PIT.EMPLOYEE TWISTED RIGHT KNEE.

EMPL INSTALLING BELT CLIPS ON BWE RECEIVING BELT.THE CLIP STUDS ARE BROKEN OFF WHEN CLIP IS INSTALLED AND THEN GROUND SMOOTH USING AIR GRINDERS.MOST LIKELY A SMALL SLIVER OF METAL RICOCHETED W HILE GRINDING OR EMPL MAY HAVE WIPED FACE WITH GLOVES ON WHICH MAY HAVE HAD METAL SLIVERS ON THEM.

INJURED WAS HELPING MAINTENANCE PULL THE TOP OFF THE GENERATOR ON D-22. WHEN THE TOP WAS OFF, THEY WERE TURNING IT OVER TO INSTALL COIL. INJURED WAS HOLDING THE CHAIN ON THE HOIST, STEADY THE TOP. THE HOOK ON THE HOIST SLIPPED AND CAUGHT HIS THUMB BETWEEN THE HOOK AND THE GENERATOR TOP.

EMPLOYEE WAS MOVING SOME METAL PALLET RACKS WITH THE USE OF FORKLIFT.WHILE GOING OUT THE DOOR THE LOAD SHIFTED ON THE FORKS,CAUSING THE EMPLOYEE TO TRY AND STOP THE LOAD FROM FALLING.THE CROSS ARMS SLIPPED AND WHEN INJURED TRIED TO CATCH THEM HE CUT HIS LEFT AHND BETWEEN THE THUMB AND FIRST FINGER.

EMPLOYEE WAS ATTEMPTING TO OPEN A BOX OF BANDING. WHILE PULLING CARDBOARD OPEN, THE CARDBOARD BROKE FREE AND HIS FINGER SLID ACROSS THE SHARP EDGE OF THE BANDING. SLICED OPEN FIRST FINGER OF R IGHT HAND ON BANDING EDGE, WHICH REQUIRED MEDICAL AID AND SIX STITCHES.

USING OVERHEAD HOIST TO INSTALL RACK SEGMENT WHILE OPENING BACK DOOR I NAME HAD THE HOIST CONTROLS IN HIS HAND HE WAS GOING DOWN THE STEPS TO UNLATCH THE BACK DOOR WHEN HE SLIPPED & FELL ON TH E STEPS TORN CARTILAGE IN LOWER LEFT RIB CAGE SORENESS IN LOWER BACK & LEFT SIDE

EE WAS SWERVICING EQUIPMENT AT SHOP FUEL DOCK. HE STEPPED OFF OF SCRAPER TO THE LUBE PLATFORM AND TWISTED HIS RIGHT ANKLE.

EMPLOYEE WAS JUMPING OFF 21065 DOZER. HE REACHED TO HOOK UP JUMPER CABLES, ADN THE BATTERY SPARKED. HE UNHOOKED CABLES AND WAS HOOKING UP AGAIN WHEN THE BATTERY BLEW UP. BATTERY ACID ON FAC E AND EYES. CUTS ON FACE AND NOSE.

EE WAS WASHING PUMP TRUCK 25325 AT WASH RACK. HE WAS PULLING ON THE HOSE, AND IT HUNG UNDER THE TIRE OF THE TRUCK. THE HOSE SLIPPED OUT OF HIS HAND, AND THE WATER WENT UNDER HIS GLASSES INTO H IS EYE.

EE WAS REMOVING BACK PLATES FROM TAIL PULLEYS HE CAME AROUND TO THE FRONT OF THE FEEDER BOX TO GET A 1 1/8INCH WRENCH FROM TOOL BOX. HE BENT OVER TO REMOVE THE TOP TRAY AND FELL TO HIS KNEES W ITH SEVERE PAIN IN HIS LOWER BACK.

EMPLOYEE STRAIGHTENED GRAB IRON ON TOP OF CAB.HE WAS SUING BOOM TRUCK TO PULL UP RAIL AND WAS HEATING WITH TORCH.THE GRAB IRON BROKE AND STRUCK EMPLOYEE IN STOMACH.

24133 SCRAPER WAS HAULING COAL FROM NO 2 STOCKPILE AND DUMPING IT IN TRUCK HOPPERS NOS 1 AND 2.INJURED MISALIGNED WITH THE SCRAPER WHILE GOING ACROSS NO 2 TRUCK HOPPER.THE RIGHT FRONT WHEEL FE LL OF IN THE HOPPER.INJURED HIT HIS RIGHT JAW ON THE PAN LEVER.

EMPLOYEE WAS HELPING WASH FRONT END OF 25335 PICKUP AT WASH RACK. HE WALKED ACROSS WASH RACK TO GET A WATER HOSE WHEN HE SLIPPED. WHEN EMPLOYEE SLIPPED, HIS LEFT LEG AND FOOT WENT FORWARD, A ND HIS BODY FELL BACKWARD. HIS RIGHT LEG BENT UNDER HIM CAUSING A SPRAIN TO HIS RIGHT KNEE.