Buscar en el registro

Employees were using starting fluid to clean equipment. They lit the starting fluid with a torch and the can fell, was punctured and landed in the fire, spraying the employee and burning the employee on face and arms.

Employees were using starting fluid to clean equipment. They lit the starting fluid with a torch and the can fell, was punctured and landed in the fire, spraying the employee and burning EE on EE's face and arms.

EE was putting a pontoon under a pipeline. While putting the cap on one of the pontoons, the cap fell and mashed finger.

Employee got overheated and became sick.

Employee was cutting a dredge sleeve loose and the sleeve hit leg causing swelling and bruising.

Employee was cutting with a torch. Hose was caught and when they pulled it free, the torch went into their glove burning the left hand.

Employee was experiencing chest pains

A torch striker that employee had on pants caught on a bolt on a pump base, causing ee to lose balance and landing on hand. Broken left wrist

Employee was patching a pipe when the trackhoe bucket swung around crushing EE's left arm between the bucket and pipe.

A can of starter fluid was tossed to employee. He missed catching it and it hit a motor, bounced off and stuck him above his left eye. He had 6 stitches above eyebrow to close up the cut.

Employee was walking on the platform and it gave way. He had cuts and abrasions to the left side of his body.

Unknown. Employee reported after leaving work his shoulder hurt. No other information is available. Nature, time, place and circumstance around injury are unknown. Employee does not know how injury occurred.

Employee was on the trailer, getting ready to set the first load. He stepped back and his foot went in a hole in the trailer. He lost his balance and fell backwards. His body was hanging off the side of the trailer and his foot was still caught in the hole. He has a severely sprained right ankle.

Employee was cutting a piece of rubber hose and his razor blade slipped and cut his left leg above the knee

Employee injured his back welding. He pulled on a piece of heavy metal and his back popped. Injured his lower right side of his back.

Employee was cutting a handrail off a barge when it fell and struck him on the back.

Employee stood on the step of the loader to see if a wire was off the starter and when he stepped down his left calf was cut by the step.

Employee was putting on an exhaust pipe when it slipped off and hit himself in the head leaving a 2 inch cut in the left side of his head.

Employee was working on a fault light on the main breaker box when the box exploded causing burns to both eyes.

Supervisor was driving a pin in the track of the Hyundai Trackhoe with a 10lb hammer. A piece of the pin broke off and went into injury's left leg. He had to have 7 stiches.

Employee went to start the outboard motor and it was in gear. To prevent cranking the motor in gear, the rope will not come out when the motor is in gear. He pulled hard on the rope and pulled a muscle in his lower back because the rope did not come out.

Employee was trying to untangle the dredge tail line that was wrapped around the pontoons. He put a shovel under the tail line to move it and when he did, he fell into the boat on his left side and injured his left knee and left wrist.

Employee was working on the dredge pump and logwasher, picking up heavy parts and breaking bolts loose with a pull handle when he strained his lower back.

Employee was fusing a pipeline together and he got too hot. He was nauseated, had blurred vision, and was seeing black spots out of his right eye.

Employee was putting a pipeline back together when the pipe smashed his left knee against the hydraulic ram on the work barge.

When finishing up a weld, the shield was raised and the rod left over would strike the metal sometimes causing an arc exposing the eyes to it. The employee burned his eyes.

Employee was on top of a fuel tank taking a pressurized cap off. He did not use the pressure relief valve first and the pressure threw him against the cab of the truck and then he fell to the ground. Employee has internal bruising around the rib area and a bruised left foot.

EE was laying a 55 gallon drum, full of oil, down on the ground. He pinched his fingers between the oil drum and a spool of rope.

EMPLOYEE WAS UNSTOPPING A SAND LINE AND A RUBBER HOSE HIT HIM ON THE LEFT LEG. HIS UPPER LEG WAS BROKEN.

Employee was unclogging a drain pipe with a stick and his right hand slipped and hit the drain pipe. His hand was scraped and swollen.

Employee was patching a pipe and it mashed his pinky finger.

Employee's left shoulder began burning and hurting while operating the dredge.

Employee was attempting to hit a bolt with a hammer and mashed his finger.

Employee was boarding the workboat. He stepped onto the bow with his left foot and his right foot sank in the wet sand, therefore not giving him enough strength to get on the boat. His left leg twisted at the knee and he landed on all fours inside the boat. He was carrying supplies in his arms.

Employee was tightening a cable on the back of the gravity plant when the excavator bucket leaked down and caused a pipe to slide and smash his left foot.

Employee was assisting in dumping 10" pieces of plastic pipe. The trackhoe was moving a piece of the pipe when the chain came unhooked and the pipe fell on him hitting him on the left side of the head and on his left shoulder.

Employee was tightening an impeller on a gravel pump with a pipe wrench. The wrench slipped and cut a gash on his forehead above his right eye.

While trying to get a dredge going, employee became overheated while in the boat.

EE was returning boat to dredge. He was on deck chaining boat off when the high wall collapsed and caused the boat to pull away. The hook on the chain stabbed his finger.

Employee was welding on a stacker. When he stood up, he cut his head by hitting it on the stacker.

Employee was checking the bearing on the outboard side of a Diester vibrator. He was turning the timing gears and pinched his right index finger.

Employee was climbing the logwasher hopper when he hit his knee on a piece of angle iron. He injured his knee cap.

While striking a cable cutter with a 12 lb hammer, a foreign object flew into employee's right eye. He was not wearing his safety goggles.

Employee was operating overburden belt fed by the backhoe. A large chunk of overburden fell off the top of the belt hitting the employee on the lower left side of the back.

Employee was operating a haul truck & somehow pulled a muscle in his back.

Employee was standing on a lab table putting up ceiling tiles - he slipped and fell off the table landing on his lunch box - Employee did not go to the doctor until August 9, 2005.

EE was over-heated. He was light-headed and nauseated-heat exhaustion.

EE WAS UNLOADING A BED ROLLER WHEN HIS RIGHT HAND GOT PINCHED BETWEEN 2 OF THEM.

He attempted to lift a 4D battery & strained back.

EE WAS TIGHTENING COME-A-LONG TO PULL BACKHOE TRACK. THE COME-A-LONG TURNED LOOSE AND EE FELL BACKWARDS AND SAT DOWN ON GROUND HARD, INJURED BEHIND AND LOWER BACK