Buscar en el registro

Employee was using a pocket knife to cut a zip tie holding wires employee needed to loosen to adjust sensor. When zip tie was cut knife continued and cut left arm above wrist.

Employee was cleaning out a material chute below the 8 X 20 screen with a bar. A rock came down from the top of the screen and hit the bar, causing it to strike the employee in the face. Employee declined medical treatment until 5/8/14.

Employee was installing wear parts in a roller mill when the angle iron supporting the come-a-long slipped, striking the employee in the upper lip and causing a laceration. No other facial or dental damage was indicated by the treating physician.

Employee was pulling on a pipe wrench trying to rotate a shaft on a screw. The shaft was locked out and tagged. The employee was using excessive effort that caused the shaft twist like a torsion bar. The employee lost his grip on the wrench and stored energy in the twisted shaft caused the wrench to hit the employee's right hand breaking a bone.

Employee was cleaning a chute in front of an 8' X 20' screen using a bar. When the material in the chute came free, the employee dropped the bar into the chute. He stated at that time that he felt a pain in his right shoulder and requested a medical evaluation.

Employee was pulling up on a bar when he felt a sharp pain in his lower neck and upper back area.

Employee was cutting steel strap with shears and it sprang back, striking him on the left thumb and cutting through his glove, causing a laceration.

Employee was tightening bolts on 8 X 20 screen at the Crusher when a very small flake of rust from the screen filtered down behind his safety glasses into his right eye.

Employee was using a hammer to clean a spill tray at the #17 belt hopper. While striking the tray with the hammer, it slipped off and he hit his left second finger on the tray, causing a laceration. Employee was not wearing gloves.

Employee was struck by a chain hoist when it came unhooked from the point of hoisting pressure. The tank leg was under tension with a chain and hoist. The leg jolted loose and sent the cain of the hoist flying and struck employee's back.

While pounding sign post (steel) on Tater Ridge Road, utilizing a post pounder without handles, EE raised post pounder above level of post. Hands were in gripped position at the bottom edge of pounder. Upon thrusting dowward, hands were pinched and lacerated upon steel post.

Employee was striking hopper with 8' rebar to dislodge material from side of hopper. While striking hopper employee claims he felt pain to left shoulder. Not reported until 11-15-05.

EE was tightening a bolt plug on a mill gear reducer when the plug stripped out and the wrench. He was using came off the bolt plug causing his left arm. He was using came off the bolt plug causing his left arm to strike against the corner of a protective guard causing a small puncture and bruise to his left upper arm above the elbow.

EE WAS UNTHAWING FROZEN BRAKES WITH A HAMMER WHEN LOWER BACK POPPED CAUSING PAIN. EE CONTINUED TO WORK UNTIL 01/03/2005, THEN WENT TO THE DOCTOR.

EE HAD AN ACCIDENT WHILE TRYING TO DISLODGE A ROCK WHICH HAD BEEN LODGED IN THE FEEDER ROLLER. ACCORDING TO EE HE HAD BEEN HAVING PROBLEMS WITH LARGE ROCKS GETTING STUCK AT THE FEEDER ROLLER. HE TRIED TO DISLODGE THESE ROCKS W/ A METAL ROD. DOING SO, THE METAL ROD GOT WEDGED BETWEEN THE ROCK & THE SIDE OF THE FEEDER ROLLER. HE LOOKED INSIDE THE FEEDER & SAW THAT THERE WAS A CLEARAN

EE WAS SCRAPING OUT BELLY DUMP TRAILER WHEN HER FINGERS WENT NUMB. SHE IS CLAIMING THAT REPETITIVE MOTION CAUSED THIS CONDITION.

EE WAS WORKING UNDER A HAUL TRUCK WHEN A WRENCH FROM ABOVE FELL AND STRUCK HIM IN THE MOUTH. HIS TOOTH WAS BROKEN IN HALF AND REPAIRED BY THE DENTIST.

EMPLOYEE WAS CLEANING INK ROLL WITH A KNIFE, WHEN HE SLIPPED CUTTING HIS RIGHT THUMB. THIS ACCIDENT REQUIRED MEDICAL ATTENTION ONLY.

MINER WAS POKING MILL FEED AT HOPPER AND PRY-BAR GOT CAUGHT IN FEED AND PULLED HAND AGAINST METAL EDGES OF HOPPER OPENING. THE RESULTING FORCE SMASHED THE FINGER, RESULTING IN THE INJURY. THE FINGER WAS TREATED WITH ABOUT SEVEN SUTURES. THE MINER HAS FULL USE OF FINGER INJURED. EMPLOYEE WAS ELIGIBLE TO RETURN TO WORK THE NEXT DAY.

EE WAS USING A BAR TO CLEAN A CHUTE AT THE CRUSHER TO DISLODGE PLUGGED MATERIAL. THE BVAR BOUNCED OFF A ROCK AND BEGAN TO FALL DOWN THE CHUTE-THE EE CAUGHT THE BAR WITH HIS LEFT HAND AND FELT HIS SHOULDER PULL AS HE DID SO. EE WAIVED MEDICAL TREATMENT UNTIL THE FOLLOWING MORNING ON 9-4-02

EE WAS USING A COMALONG TO REPOSITION A RADIAL STACKER (CONVEYOR). HE SECURED BOTH ENDS OF THE COMEALONG TO WELDED EYES ON THE STACKER AND THE TRACK FRAM IT RUNS ALONG. WHEN HE TIGHTENED THE C OMEALONG, THE EYE ON THE TRAKC BROKE, FREEING THE END OF THE COMALONG AND CAUSING IT TO SPRING UP AND IT STRUCK THE EE IN THE BACK. EE DECLINED MEDICAL TREATMENT UNTIL 8-2-02 WHEN HE SOUGHT S

THE EE WAS PERFORMING MAINTENANCE ON THE HYDRAULIC SYSTEM OF THE WATER TRUCK. WHILE TIGHTENING A FITTING ON THE TANK, HIS WRENCH SLIPPED AND HE STRUCK HIS RIGHT HAND AND WRIST ON THE TANK FRAM E.

EE WAS STIKING FRAME OF CONVEYOR BELT WITH HAMMER TO DISLODGE ICE WHEN HE FELT A SHARP PAIN IN HIS LEFT ELBOW. PAIN PERSISTED, THEREFORE HE WAS TAKEN IN FOR EXAMINATION BY A PHYSICIAN.

CUTTING HYDRAULIC HOSE WITH CHOP SAW, WHEN METAL FLEW OFF SAW BOUNCED OFF SAFETY GLASSES AND INTO LEFT EYE.

EE WAS PERFORMING CLEANUP INSIDE THE 57" CONE CRUSHER AT THE CLOSE OF SHIFT. WHILE SCRAPING DOWN THE SIDES OF THE CONE, A CHUNK OF DISLODGE MATERIAL FELL AND STRUCK HIM ON THE RIGHT WRIST AREA . EE DID NOT SEEK MEDICAL ATTENTION UNTIL THE FOLLOWING DAY.

EE WAS CUTTING A PRODUCT HOSE WITH A HAZOR KNIFE WHEN KNIFE SLIPPED AND PUNCTURED HIMSELF IN THE KNEE. NO WITNESSES. EE WENT ER AND WAS GIVEN STITCHES.

FIRST EE WAS HELPING TO TIGHTEN BOLTS ON JAW CRUSHER USING A 10 LB HAMMER TO STRIKE THE WRENCH HANDLE BEING HELD BY SECOND EE. FIRST EE MISSED THE WRENCH HANDLE WITH THE HAMMER ON ONE STROKE A ND IN THE PROCESS HE SMASHED HIS LEFT SMALL FINGER BETWEEN THE HAMMER HANDLE AND A PLATE ATTACHED TO THE JAW. EE DID NOT SEEK MEDICAL TREATMENT UNTIL 5-13-99.

EE WAS USING A HAMMER TO REMOVE A LIP GUARD ADAPTER FROM LOADER. WHILE DOING THIS, A SMALL PIECE OF METAL FLEW UP AND STRUCK HIM IN THE LEFT CHEEK AREA BELOW SAFETY GLASSES, CAUSING A SMALL LA CERATION. (EE PULLED THE METAL FROM THE WOUND AND DID NOT REPORT THE ACCIDENT UNTIL HE BEGAN HAVING PROBLEMS WITH THE WOUND AND SOUGHT MEDICAL TREATMENT ON 3/6/99.)

POUND RAIL SPIKE IN TO THE TIE THE SPIKE FLEW BACK HITTING EE IN UPPER LIP LACERATED UPPER LIP

EMPLOYEE WAS CLOSING A SLIDING BUS WINDOW. THE LATCH WAS STUCK AND HE WAS USING A POCKET KNIFE TO MOVE THE LATCH. THE LOCKING BLADE ON HIS KNIFE UNLOCKED AND THE BLADE CLOSED ON HIS FINGER CUT TING HIS FINGER.

REMOVING A MILL SPIDER FROM #3 MILL USING A CHAIN TIED TO A HYDRAULIC RAM, CHAIN LINK BROKE, HITTING EE UNDER NOSE AREA.

EE WAS ASSISTING AN OUTSIDE TECH REP IN ADJUSTING THE 57FC CONE CRUSHER, USING A COME-A-ALONG. AFTER TIGHTENING THE COME-A-ALONG AS FAR AS IT WOULD GO, HE WAS INSTRUCTED BY THE TECH REP TO USE A CHEATER PIPE OVER THE HANDLE OF THE COME-A-ALONG TO TIGHTEN IT FURTHER. THE COME-A-ALONG BROKE AND THE CHAIN BACKLASHED, STRIKING THE EE IN THE RT ARM.

EE WAS PERFORMING MAINTENANCE ON MILL EQUIPEMENTHE WAS LOOSENING A BOLT TO REMOVE A PLATE, THE BOLT WAS VERY TIGHT & WHEN EE PUT PRESSURE WITH THE HAND TOOL TO LOOSEN BOLT, HE FELT A SHARP PAIN IN HIS LEFT CHEST AREA THAT CONT AFTER HE STOPPED WHAT HE WAS DOING

EE WAS BARRING WET MUD FROM MILL FEED PIPE, AND HAD BEEN DOING SO FOR SEVERAL HOURS PRIOR, AND EITHER SPRAINED OR STRAINED A MUSCLE IN BACK AND SHOULDER AREA.

EE WAS USING A CROW BAR & SMASHED HIS FINGER BETWEEN THE BAR & A PIECE OF METAL.

EE WAS PERFORMING REPAIRS WITH SHIFT BOSS ON BELT TAIL PULLEY. WHILE SHIFT BOSS WAS HAMMERING PULLEY BEARING, A PIECE OF METAL FLEW UP AND STRUCK EE IN THE NECK, EMBEDDING IN THE FLESH.

EE WAS CLEANING MATERIAL AWAY FROM RAILROAD TRACKS USING A PICK, AS HE SUNG THE PICK IT HIT THE TRACK CAUSING HIM TO STRAIN A MUSCLE IN HIS SHOULDER.

THE EMPLOYEE WAS USING A WRECKING BAR ON THE HOPPER CAR GATE, THE BAR SLIPPED OFF ADN PINCHED HIS FINGER.

WHILE CLEANING HARD MATERIAL FROM CHUTE WITH A T HANDLED SCRAPPER. EMPLOYEE SMASHED MIDDLE FINGER LEFT HAND BETWEEN T HANDLE AND A PIECE OF METAL SCREEN.

WHILE INSTALLING AN ADAPTER PLATE TO THE BOTTOM OF #5 MILL, THE INJURED WAS IN A SITTING POSITION, WHILE TRYING TO POSITION THE ADAPTER PLATE, THE INJURED STRAINED HIS UPPER RIGHT BACK. HE DID NOT WORK 6-9-95 FOR PERSONAL REASONS. RE-IN JURED HIS BACK ON 6-10-95 WHILE PULLING ON A PIPE WRENCH.

WHILES USING A METLA PRY BAR TO PRY FEED GATE OPEN ON #1 MILL THE EMPLOYEE FELT PAIN IN HIS BACK, EMPLOYEE RPORTED ACCIDENT BUT SAID HE WOULD BE OK AND CONTINUED WORKING. THE INJURY HAS BOTHE RE HIM ON AND OFF SINCE THEN BUT HE SAID HE WOULD BE ALRIGHT. ON 7-17-95 EE WENT OT THE DR HIS FIRST DAY OF WORK MISSED WAS 7-18-95.

EMPLOYEE WAS TIGHTENING JAW CRUSHER ADJUSTMENT BOLT WITH A SLEDGE HAMMER AND SLUGGING WRENCH. HAMMER BOUNCED OFF OF WRENCH, STIKING EMPLOYEE IN THE LEFT FOOT.

PRYING UP ON A TRUCK FENDER AND BAR SLIPPED CRUSHING LEFT RING FINGER.

EMPLOYEE WAS POSITIONED AT TOP OF CONE CRUSHER INSTALLING WEDGES, SWUNG SLEDGE HAMMER AND MISSED WEDGE, SLIPPED OFF BALANCE AND STARTED TO FALL. HE CAUGHT HIMSELF WITH RIGHT HAND ON TOP OF CON E, STRAINING RIGHT SHOULDER AND STRIKING KNEE ON SIDE OF CRUSHER. EMPLOYEE DID NOT SEEK MEDICAL ATTENTION UNTIL 6-14-94.

EE WAS THREADING CABLE THRU LIFTING EYE ON LOADER ARM WHILE IT WAS SUSPENDED BY HELPER WITH PRY BAR LOADER ARM SLIPPED FROM PRY BAR AND CAUGHT EE S HAND BENEATH, DISMEMBERING FIRST JOINT FROM RIGHT HAND INDEX FINGER.

EE WAS LOOSENING NUT ON RETURN ROLLER OF CONVEYOR BELT WHEN CRESENT WRENCH SLIPPED OFF OF NUT. EE STRUCK HIMSELF WITH THE WRENCH ON BRIDGE OF NOSE, LACERATING IT.