Buscar en el registro

INJURES EMPLOYEE WAS USING UTILITY KNIFE TO INSTALL POLY-DECK SECTIONS ON VIBRATING SCREEN AND CUT THE TOP OF LEFT HAND. HE WAS NOT WEARING GLOVES.

EMPLOYEE WAS TIGHTENING WEDGE BOLTS ON CONE CRUSHER #1 WHEN THE WEDGE FLEW UP STRIKING EMPLOYEE IN THE NOSE.

EE & COWORKERS WERE CHANGING THE BEARINGS ON A BLT CONVEYOR HEAD PULLEY. AS EE REMOVED THE FINALFEW BOLTS THE PULLY DROPPED DOWN & CAUGHT HIS FINGER BETWEEN THE PULLEY & THE BEARING HOUSING. T HE COMALONG WAS NOT PROPERLY POSITIONED TO SUPPORT THE WEIGHT OF THE PULLEY WHEN THE FINAL BOLTSWERE REMOVED

INJURED EMPLOYEE WAS REPOSITIONING SCREW JACK STABLIZERS ON THE PORTABLE CRUSHING PLANT. THE 4' BAR USED TO SCREW THE JACKS UPWARD SLIPPED OUT OF THE HOLE AND THE END OF THE BAR STRUCK THE RIG HT SIDE OF HIS HEAD. HE WAS WEARING HARD HAT PROTECTION.

EMPLOYEE WAS PREPARING TO SPLICE A RUBBER CONVEYOR BELT AND CUT HIMSELF WITH A KNIFE AS HE WAS TRIMMING THE BELT.

EMPLOYEE AND CO-WORKER HAD HOOKED A CHAIN ONTO A CHUTE BEING USED WITH A PROATABLE SCALPING SCREEN. AS THE INJURED EMPLOYEE WAS PULLING ON THE CHAIN TO MOVE THE CHUTE INTO POSITION, HE FELT DI SCOMFORT IN HIS LOWER BACK.

EMPLOYEE WAS HELPING TO REPAIR SWING CLUTCH ON DROPBALL CRANE. AS HE WAS USING PRYBAR TO ASSIST IN REMOVING BOLTS, IT SLIPPED AND STRUCK HIS FOREHEAD. EMPLOYEE WAS WEARING HARDHAT AND SAFETY G LASSES.

INJURED EMPLOYEE AND CO-WORKER WERE REPLACING SKIRTBOARD ON #21 BELY CONVEYOR. EMPLOYEE WAS USING UTILITY KNIFE TO CUT SLOTS INTO RUBBER KNIFE AND HIS FOREARM.

EE WAS TIGHTENING TENSION BOLT ON THE NUMBER 2D VIBRATING SCREEN. WHILE APPLYING PRESSURE ON THE HAND WRENCH, THE BOLT HEAD BROKE AND HIS THUMB WAS CAUGHT BETWEEN WRENCH AND MOTOR GUARD.

EE WAS USING KNIFE TO WHITTLE WOODEN HAMMER HANDLE.

EE WAS HELPING ANOTHER EE ADJUST THE CRUSHER. WHILE REMOVING A BOLT IN THE ADJUST RING, THE BOLT GOT STUCK IN THE HOLE. EE TRIED TO PRY IT OUT WITH A CROWBAR AND THE BAR SLIPPED AND MASHED HIS FINGER AGAINST THE CRUSHER.

EE WAS RESTING A RIECE OF RUBBER HOSE ON HIS LEG& CUTTING THE DAMAGED END WITH A RAZOR KNIFE. THE KNIFE WENT THROUGH THE RUBBER & CUT HIS LEG.

EE WAS PRYING WITH A STEEL BAR. THE BAR SLIPPED AND MASHED HIS FINGER BETWEEN THE BAR AND ANOTHER PIECE OF STEEL.

EE WAS TRYING TO PRY A ROCK LOOSE FROM A CHUTE AND FELT SOMETHING PULL IN HIS ARM

EMPLOYEE WAS USING KNIFE TO CUT PLASTIC TIES TAHT SECURED THE STRAP ON HIS WELDING GOGGLES TO HIS HARDHAT. HE CUT HIS THUMB.

WORKING ON A 4 1/4 CRUSHER TRYING TO LOOSEN THE BOWL WITH A HYDRAULIC JACK. THE JACK BRAKE AND THE HEAD RETRACTED MASHING HIS FINGER BETWEEN THEBOWL AND THE JACK. HE NEEDED 3 STITCHES TO REPAI R THE CUT ON HIS THUMB.

EMPLOYEES WERE USING A CABLE HOIST & J HOOK TO REMOVE A ROCK THAT WAS BLOCKING THE OPENING TO THE JAW CRUSHER AS THEY HOISTED THE ROCK THE HOOK JUMPED UP & STRUCK THE EMPLOYEE ON THE HAND IT M ASHED HIS FINGER BETWEEN THE HOOK & THE GUARD RAIL CRUSHING THE BONE JUST ABOVE THE MIDDLE JOINT THE HOSPITAL REMOVED HIS FINGER ABOVE THE MIDDLE JOINT

DISASSEMBLING A 7FT CRUSHER HEWAS PUSHING ON HAMMER HEAD TO REMOVE A HEAD NUT & PULLED A MUSCLE IN HIS LEFT CALF

EMPLOYEE WAS USING SLEDGE HAMMER OT DRIVE WEDGE FOR CONE CRUSHER ADJUSTMENT. HIS LEFT HAND SLIPPED OFF HAMMER AND WAS CAUGHT BETWEEN HANDLE AND WEDGE.

EMPLOYEE WAS HLEPING TO SPLICE CONVEYOR BELT, DURIN POSITIONING OF BELT AND CLAMP IT SHIFTED AND PINNED LEFT KNEE AGAINST CONVEYOR FRAME.

HIT HIS HAND WITH A HAMMER WHILE DRIVING A PIN OUT OF A DIPPER TOOTH. HE WAS WEARING GLOVES, BROKEN LEFT THUMB.

EE WA USING APIPE, FOR LEVERAGE, TO LOOSEN CHAIN HOIST THAT WAS IN A BIND. THE PIPE SLIPPED AND HE WAS STRUCK ON THE CHIN.

EMPLOYEEW AS TIGHTENINGA BOLT ON A SHAKER SCREEN. THE WRENCH HE WAS USING SLIPPED AND HE HIT HIS ELBOW ON THE SIDE OF THE SCREEN.

EMPLOYEE WAS CUTTING A PIECE OF RUBBER BY PULLING THE KNIFE TOWARDS HIM. THE KNIFE SLIPPED AND HE CUT HIS KNEE REQUIRING 11 STITCHES.

EE WAS HELPING TO TIGHTEN BEARING BOLTS ON THE JAW CRUSHER FEEDER. THE FEEDER MOTOR WAS JACKED TO ONE SIDE ON PIVOT USING A CHAIN HOIST AND RUBBER DRIVE BELT THE DRIVE BELT BROKE AND THE MOTOR FELL ON EE ARM WHILE HE WAS USING A WRENCH TO TIGHTEN BOLTS.

EMPLOYEE WAS REMOVING BELT WIPER FROM #7 BELT CONVEYOR.THE BOLTS HAD BEEN REMOVED FROM ONE SIDE AND IT WAS RESTING ON CONVEYOR FRAME.HE WAS UNBOLTING THE OTHER SIDEIT DROPPED DOWN SUDDENLY AND CAUGHT HIS THUMB BETWEEN THE CONVEYOR AND WIPER.EMPLOYEE WAS WEARING WORK GLOVES.

54736YE EWAS CHANGING DRAG CABLE ON UNIT 238 DRAGLINE CRANE. HE PLACED THE DEAD-END OF CABLE (1 1/8") INTO SOCKET AND WAS PREPARING TO DRIVE THE WEDGE INTO PLACE WITH HAMMER. THE END OF CABL 50314E OUT OF SOCKET AND STRUCK EMPLOYEE IN THE FACE. HE WAS WEARING INDUSTIRAL SAFETY GLASSES.

55061S REMOVING THE HITCH PIN ON AN ARTICULATING REAR DUMP HAUL TRUCK BY STRIKING A CHISEL WITH A MECHANICS HAMMER THE CHISEL FLEW BACK AND STRUCK EE ON THE LEFT SIDE OF NOSE.

EMPLOYEE WAS KNEELING ON TOP OF DRILL TRUCK CAB WHILE TIGHTENING A BOLT ON DRILL CAROUSEL. THE WRENCH SLIPPED OFF BOLT AND EMPLOYEE FELL BACKWARDS FROM THE CAB TO THE GROUND.

REPLACING COUNTER WEIGHT ON SHAFT HE HIT IT WITH A HAMMER TO STRAIGHTEN IT ON THE SHAFT & IT FELL OFF HE & ANOTHER EMPLOYEE TRIED TO CATCH IT BUT THE WEIGHT PULLED IT DOWN HE MASHED HIS FINGE R BETWEEN THE COUNTER WEIGHT & A GUARD SUPPORT BRACKET

EMPL USING T-HANDLE PRY BAR TO DISLODGE ROCKS FROM CONE CRUSHER AND CAUGHT FINGER BETWEEN HANDLE AND CRUSHER AS ROCK BROKE FREE.WAS WEARING WORK GLOVES.

EMPLOYEE WAS USING PIN MAUL & SLEDGE HAMMER TO REMOVE LINK PIN ON TRAVEL CHAIN OF DROPBALL CRANE A SPLINTER OF METAL STRUCK HIS HAND

WE WERE PUTTING A STEEL TOOTH ON LOADER BUCKET, DRIVING IT ON BY HITTING IT (TOOTH) WITH SLEDGE HAMMER. A PIECE OF STEEL SHIVER CAME LOOSE HITTING AND EMBEDDING IN HIS LEFT FOREARM.

USING KNIFE CUT STYROFOAM INSULATION AND CUT L INDEX FINGER

INSTALLING TRACK PINS IN 80-D SHOVEL TRACKS. I.NAME WAS HITTING PIN WITH SLEDGE HAMMER WHEN SHIVER OF PIN FLEW OFF HITTING HIM IN CHEST.

USING CHAIN HOIST TO CHANGE BELTS ON CRUSHER, RATCHET NOT ENGAGED COMPL. HANDLE STRUCK IN NOSE

EMPLOYEE WAS REPLACING BUCKET TEETH RETAINING BOLTS ON DRAGLINE BUCKET.HE WAS DRIVING THE BASE PLATE INTO POSITION WITH A SLEDGE HAMMER WHEN A PIECE OF METAL CHIPPED OFF THE BASE PLATE AND STR UCK HIS LEFT LEG.

EMPL WAS WELDING ON FRONT END LOADER BUCKET HE LIFTED HIS WELDING SHIELD TO CHIP AWAY WELDING SLAG AND A SMALL PIECE STRUCK HIS EYELID HE WAS NOT WEARING SAFETY GLASSES UNDERNEATH HIS WELDING SHIELD

ENJOYED WAS KNOCKING OUT ROCK THAT HAD LODGED OR CAUGHT BETWEEN THE TWO WHEELS TIRES ON HAUL TRUCK. HE WAS USING SLEDGE HAMMER TO HIT ROCK A PEG ROCK BROKE OFF OR CAME LOOSE HITTING AND CUT IN DEX FINGER ON RT HAND.

EMPLOYEE WAS TIGHTENING THE BOLTS ON THE CHEEK PLATE THAT WAS INSTALLED ON THE JAW CRUSHER. HE WAS USING A SLEDGE HAMMER AND HAMMER WRENCH TO TIGHTEN THE BOLTS. WHILE HOLDING THE WRENCH WITH H IS LEFT HAND HE STRUCK IT WITH THE HAMMER. HE WAS WEARING WORK GLOVES.

EE AND CO WORKER WERE REPLACING LINER IN 5 1/2 CRUSHER. THEY HAD TIGHTENED THE 8 RETAINING V-BELT AND NUTS WITH A CHEATER BAR. THEN THEY WERE POSITION THE NUTS INSIDE THE LOCK PLATES BY STRIKI NG A PULL HANDLE AND 38 SOCKET WITH A SLEDGE NUTXX HAMMER HE WAS HOLDING THE PULL HANDLE WHILE A CO WORKER STRUCK HANDLE WITH SLEDGE HAMMER. HAMMER GLANCED OFF PULL HANDLE STRIKING EE MOUTH.

EMPLOYEE & COWORKERS WERE REPLACING SNUBBER PULLEY THEY WERE HOISTING THE PULLEY WITH A COMEALONG & AS THEY WERE SWINGING THE PULLEY FROM THE CONVEYOR BELT ONE SIDE OF THE PULLEY DROPPED DOWN CAUSING THE OTHER END TO JERK UPWARD CATCHING HIS HAND BETWEEN THE PULLEY SHAFT & CONVEYOR FRAME

EMPLOYEE WAS USING A SLEDGE HAMMER TO DRIVE OUT WEDGE IN CROWS FOOT FOR ORAG CABLE ON UNIT 228 AS HE STRUCK THE PIN M AUL WITH HAMMER A METAL FRAGMENT SOPLINTERED & PUNCTURED INSIDE LEFT KNEE REQUIRING HOSPITALIZATION & SURGICAL REMOVAL SLEDGE HAMMER WAS NEW & THE PIN MAUL WAS PROPERLY DRESSED

USING DRY BAR TO ON CLOG CHUTE- ROCK CAME LOOSE FELL HITTING HIM IN MOUTH.

TAKING SHIMS OUT OF JAW CRUSHER,WHILE USING CHAIN JACK TO PULL SHIM OUT OF CRUSHER-CHAIN HITTING INJURED ACROSS RIGHT KNEE.

A LARGE ROCK BECAME LODGED IN 4 TUNNEL SYNTRON EMPLOYEE WAS USING A PRYBAR TO DISLODGE ROCK & THE PRY BAR SLIPPED & STRUCK HIS LEFT EYE EMPLOYEE HAD REMOVED SAFETY GLASSES PRIOR TO INCIDENT