Buscar en el registro

EE WAS HITTING A PIN ON THE STAMLER CHAIN WITH A SLEDGE HAMMER. ANOTHER EE LEANED DOWN. WE THINK HE DID THIS TO HOLD THE CHAIN. WHEN EE HIT THE PIN, HAMMER BOUNCED OFF THE PIN HITTING THE OTHE R EE IN THE FACE.

EE WAS CLOSING THE DOOR OF THE HAMMERMILL WITH A YALE 1 1/2 TON COME ALONG WHEN THE DOOR SLIPPED OUT OF ALIGAMENT. HE RE-ATTACHED THE COME ALONG TO REALIGN THE DOOR. EE WAS WONDERING IT AN AWK WARD POSTION WITH THE COME ALONG WHILE WORKING TUHE COME ALONG. RIGHT ARM GREW TIRED AND HE SWITCHED TO HIS LEFT. HE STRAINED WITH HIS LEFT ARM AND FELT THE INJURY OCCUR.

EE WAS IN CLINKER COOLER DUST COLLECTOR HELPING 2 OTHER EES PULL A SCREW BACK TOGETHER USING A COMEALONG. HE WAS KNEELING ON ONE KNEE PULLING THE COMEALONG WHEN HE FELT A "POP" & THEN BACK PAI N.

USING BAR TO TRY & MOVE BACKSTOP BACK INTO PLACEBAR SLIPPED CAUSING EE TO FALL FORWARD, INJURINGHIS SHOULDER

PRYING A CAGE OUT OF A DUST COLLECTOR BAG USING A T-HANDLE. CAUGHT FINGER BETWEEN T-HANDLE AND DOOR.

WHILE PRYING ON BAUXITE CHUNKS WITH BAR, EMPLOYEE EXPERIENCED PAIN IN RIGHT SHOULDER.

EMPLOYEE WAS USING A HAMMER AND A CHIPPING HAMMER, WHEN A PIECE OF METAL BROKE OFF, AND LODGED INTO HIS LEFT HAND.

WHILE REMOVING BEARING ON CRUSHER MOTOR WITH HAMMER, EE CAUGHT PINKY BETWEEN HAMMER HEAD AND MOTOR, SMASHING HIS FINGER.

EMPLOYEE WAS WELDING WHEN HE WAS HIS IN THE BACKWITH A CLINKER BREAKER HAMMER.

WHILE REMOVING A DRIVE SEGMENT ON D9 DOZER, A PIECE OF STEEL CHIPPED OFF THE SEGMENT AND STRUCK EMPLOYEE IN THE NECK.

AFTER CLEANING HARDENED CEMENT MATERIALS FROM THE TURNHEAD, FEEDBOX AND TRIPPER WITH A METAL BAR, THE EMPLOYEE EXPERIENCED PAIN IN RIGHT ARM.

EE WAS PULLING A BELT BACK TOGETHER WHEN CHOKER BROKE BLOCK STRUCK EE IN UPPER CHEST AND HEAD.

EMPLOYEE FELT PAIN IN RIGHT SHOULDER WHEN PULLING DOWN COME-A-LONG HANDLE THAT WAS MOUNTED OVERHEAD.

EMPLOYEE WAS HOLDING A BAR AND HITTING IT WITH A HAMMER. THE SLEDGE HAMMER HAD A LONG HANDLE AND IT CAUGHT A FLANGE CAUSING HAMMER TO HIT HIS FINGER, BROKE LEFT HAND LITTLE FINGER.

EE WAS TAKING DOOR OFF CLEAN OUT PORT ON VERTICLE RAW MILL TO CLEAN MATERIAL FROM AREA. DOOR DROPPED ON HAND. CUT TO LEFT LITTLE FINGER.

EE WAS SCORING CONDUIT CORER WITH A RAZOR KNIFE; KNIFE SLIPPED, CUTTING FOURTH FINGER ON LEFT HAND.

EMPLOYEE WAS ATTEMPTING TO ALIGN A COUPLING ON TO A MOTOR SHAFT WITH A RUBBER MALLET, AND HE STRUCK HIS HAND WITH MALLET. THE CUT REQUIRED SOME STITCHES.

EMPLOYEE SPRAINED RIGHT WRIST WHILE PULLING COME-A-LONG.

EE WAS WORKING ON DUST COLLECTOR SCREWS, WHEN HE TWISTED THE WRONG WAY AND STRAINE HIS LOWER BACK.

EE WAS HOLDING A B&D PUNCH WHILE ANOTHER EE WAS HITTING B&D PUNCH WITH SLEDGE HAMMER. DURING HAMMERING A PIECE OF METAL BROKE OFF AND STRUCK EE LEFT UPPER ARM PUNCTURING IT

EE WAS CUTTING PLASTIC BANDS OFF OF A PALLET OF STRETCVH HOOD FILM ROLLS. EE STATED DURING ACCIDENT INVESTIGATION THAT HE WAS IN AN AGITATED STATE BECAUSE THE PALLET WAS BROKEN AND THIS WAS WH Y HE WAS TOLD TO TRANSFER THE ROLLS FROM THE BAD PALLET TO ANOTHER PALLET. USING A UTILITY KNIFE HE CUT TOWARDS HIMSELF AND WHEN THE RETAINING BAND WA CUT, THE KNIFE WENT INTO HIS ARM.

DURING ROUTINE EXTRICATION OF BAGHOUSE BAGS (FILTERS) EE WAS USING CHANNEL LOCK PLIERS TO GRAB TOP OF BAC. BAG TORE AND THE FORCE HE WAS USWING ALLOWED HIS ELBOW TO STRIKE BOTTOME SIDE OF HORI ZONTAL DOORFRAME CAUSING INJURY.

FULLER CO. EE WAS TURNING WRENCH BEING HELD IN PLACE BY OUR EE WHEN THE WHENCH SLIPPED STRIKING OUR EE IN THE MOUTH. CHIPPED HIS TOOTH REQUIRING DENTAL WORK.

PULLING A HOIST, STRAINED LEFT SHOULDER.

EMPLOYEE STEPPED ON BOBCAT BUCKET TO MAKE REPAIRS INSIDE. THE CHAIN HOLDING THE CAB DISENGAGED AND THE CAB FELL CUTTING SCALP ON LEFT SIDE REQUIRING NINE STITCHES. (LOWER LEG ABRAISED, CONTUSI ON LEFT SHOULDER)

INDIVIDUAL STRUCK HIS LEFT PINKY FINGER BETWEEN SLEDGE HAMMER HANDLE AND BOLT HEAD.

EMP WAS PUTTING GRIZZLIES IN #1 COOLER. THE LASTONE WAS TIGHT GOING IN, SO THE EMP USED A HAMMERTO TRY TO DRIVE IT IN. IT THEN POPPED OUT AND HIT HIS LEGS.

EMPLOYEE STRUCK HAND IWTH BACK MALLET WHILE DOING PATCH WORK IN THE KILN.

CHANING TAIL/PULLEY USING BAR TO PRY-BAR SLIPPEDCATCHING FINGER BETWEEN BAR & STEEL STRUCTURE.

EMP WAS TIGHTENIGN BOLTS ON FLANGE WHEN WRIST CAME IN CONTACT WITH HOT PIPE.

EE WAS REMOVING GUARD FROM THE SECONDARY DRIVE ON #1 CEMENT KILN CLINKER COOLER WITH A BAR. BAR SLIPPED, CUTTING LEFT HAND.

EMPLOYEE WAS CUTTING NEW MAGNET BELT WHEN THE KNIFE SLIPPED CUTTING HIS RIGHT THIGH. REQUIRED 3 STITCHES.

EE PUTTING NEW SKIRTS ON COAL BELT AND WAS CUTTING A HOLE IN THE RUBBER TO FIT ON THE BOLT WHEN THE RAZOR KNIFE SLIPPED, CUTTING LEFT HAND.

EE WAS CHANGING OIL ON PLANETARY WHEN THE WRENCH SLIPPED AND EE STRUCK ELBOW AGAINST THE TIRE MM. EE WENT TO DR ON 9-12-95.

THE HOIST WAS BEING RUN TO TAKE UP BLOCK FOR #1 RAW SLIDESHOE EE NOTICED THAT THE BLOCK WAS SWINGING & GRABBED THE CABLE TO STEADY THE BLOCK WHILE DOING SO HIS FINGER WAS CAUGHT BETWEEN THE CA BLE & THE HOIST

CUT THUMB WHILE OPENING BOX.

METAL FRAGMENTS WENT INTO ARM WHEN EMPLOYEE WAS HAMMERING ON A PIECE OF METAL.

WHILE HOISTING AN OLD BELT TOP IDLER ONTO THE BELT, END DROPPED AND CAUGHT EMPLOYEE'S LITTLE FINGER. EMPLOYEE'S GLOVE AND FINGER WERE CUT. REQUIRED 28 STITCHES.

EE WAS LOADING TANK TRUCK A VALVE BECAME STUCK EE TOOK 81LB SLEDGEHAMMER AND BEGAN BEATING HANDLE EE MISSED THE HANDLE AND HIT HIS HAND ON THE HANDRAIL.

EMPLOYEE WAS USING WRENCH TO TIGHTEN PIPE UNION WHEN THE CONLDUIT CLAMP SLIPPED. EMPLOYEE FELT BURNING SENSATION IN GROIN AREA. SURGERY SCHEDULED FOR 04/18/95.

EMPLOYEE DENIES INCIDENT OF INJURY WHICH CAUSES PAIN IN RIGHT SHOULDER. INDICATES THAT HE FELT THIS PAIN WHEN HE WAS USING A SLEDGE HAMMER AND WAS HAMMERING IN AN UPWARDS POSITION.

EMPLOYEE WAS HAMMERING KILN WITH SLEDGE HAMMER AND FELT A POP IN HIS WRIST. WRIST WAS SPRAINED.

EMPLOYEE WAS PULLING ON A WRENCH WHEN HE FELT A PAIN IN HIS LOWER BACK. THE PAIN WENT AWAY INT EH AFTERNOON BUT STARTED UP AGAIN ON 10-5-94 AND HAS CONTINUED SNCE THEN. BECAME MEDICAL CASE ON 11-11-94. EMPLOYEE ON LIGHT DUTY.

WHILE STRIPPING BELT, LOOKING FOR A SPLICE, THE KNIFE SLIPPED FROM WEBBER HOLDING IT IN PLACE AND CUT HIS FOREARM.

EMPLOYEE WAS PERFORMING DUTIES IN THE MAINTENANCE DEPARTMENT. HE WAS PULLING ON COME-ALONGS AND THEY JERKED HIS HAND BACK. WHEN HIS HAND WAS JERKED BY THE COME-ALONGS HE CAUGHT HIS FINGER. X-R AY OF THE FINGER SHOWED IT WAS FRACTURED.

EMPLOYEE WAS STRIPPING WELDING LEAD CABLE FOR WELDING LEAD CONNECTOR REPLACEMENT, UTILITY KNIFE, SLIPPED AND CUT RIGHT THUMB.

EMPLOYEE WAS CUTTING A PIECE OF 16" BELT WITH HIS POCKET KNIFE. HE PULLED THE KNIFE THROUGH THE BELT TOWARD HIMSLEF & CUT HIS LEG. HE REQUIRED SEVERAL SUTURES TO CLOSE THE WOUND.

EE WAS DISLODGING TIRES FROM THE CHUTE WITH A ROD TOO SHORT FOR THE TASK BEING DONE. GATE CLOSED SEVERELY BRUISING LEFT FOREARM.

WHILE INSTALLING A 1/2" DIAMOETER NUT ON A OBLT, THE BOLT SCREWED A PIECE OF THE THREAD OUT OF THE NUT AND INTO THE LEFT INDEX FINGER.

EMPLOYEE WAS REMOVING A BOLT FROM AXLE NUT RETAINER ON 280 DOZER & THE WRENCH SLIPPED WHEN THE WRENCH SLIPPED HE CUT HIS KNUCKLE ON HIS RT HAND REQUIRING STITCHES