Buscar en el registro

EMPLOYEE CLAIMED HE INJURED HIS BACK AND NECK WHILE OPERATING THE FRONT-END LOADER INTO THE STOCKPILE OF MATERIAL. HE STATED THE MACHINE JERKED AS HE WENT INTO THE STOCKPILE WITH THE LOADER BU CKET.

WHILE USING PRY BAR TO REMOVE COUNTER-WEIGHT FROM #3 SCREEN, PRY BAR SLIPPED OFF OF COUNTER-WEIGHT AND STRUCK EE IN MOUTH CAUSING LACERATION INSIDE MOUTH.

IN PROCESS OF DRIVING COUPLER ONTO INPUT SHAFT OF GEARBOX, THE PIN BEING USED TO DRIVE COUPLING ONTO THE SHAFT FRACTURED SENDING A PIECE OF METAL IN DIRECTION OF INDIVIDUAL STRICKING HIM IN TH E WRIST AREA OF RIGHT ARM.

EE WAS SMOOTHING METAL TOOL ITEMS ON BENCH GRINDER THE TOOL BECAME CAUGHT, THE TOOL WAS DRAWN INTO THE WHEEL & THE EE'S FINGER WAS CAUGHT ON THE GRINDING WHEEL. THE GRINDING WHEEL CAUSED THE ABRASION TO THE FINGER

EMPLOYEE SLIPPED FROM 1ST STEP OF HAUL TRUCK AND FELL TO GROUND ON HIS SHOULDER. EMPLOYEE WAS TREATED FOR A EE UP UNTIL 6-19 WHEN DR .

EE WAS USING A HAMMER TO REMOVE BEARING RACE FROM BEARING HOUSING. WHILE DRIVING RACE FROM BEARING HOUSING, RACE BROKE FREE. EE SWUNG HAMMER AND STRUCK HOUSING EDGE CAUSING LACERATION.

THE INJURED EE WAS OPENING A FENCE GATE WHEN HIS LEFT HAND WAS CAUGHT IN A FENCE ROLLER. EE HAD HIS LEFT HAND ON TOP OF GATE WHILE PUSHING THE GATE OPEN. WHEN THE GATE WAS FULLY OPEN HIS LAST THREE FINGERS ON HIS LEFT HAND WAS CAUGHT BETWEEN THE TOP POST AND THE ROLLER WHEEL.

THE EMPLOYEE WAS CUTTING BOLTS FROM THE REAR CRUSHER HOUSING & WHEN THE LAST BOLT WAS REMOVED THE HOUSING TIPPED BACKWARD & STRUCK THE EMPLOYEE THE HOUSING WAS NOT SECURED BEFORE REMOVING THE BOLTS A PROCEDURE THAT IS NORMALLY DONE BEFORE THE HOUSING BOLTS ARE REMOVED

EE WAS OPERATING THE DOZER IN THE STRIPPING AREAOF THE PIT. UNKNOWINGLY HE DROVE THE DOZER INATOAN 8' DITCH THAT WAS CREATED THE SHIFT BEFORE. THE DOZEN WENT INTO THE DITCH & THE FORCE CAUSED THE EE TO STRIKE HIS HEAD ON THE OPERATOR'S CAB.THE JARRING MOTION CAUSED THE HERMIATED DISC PROBLEM IN HIS NECK & BACK AREA.

THE INJURED EMPLOYEE WAS USING WRENCH TO LOOSEN SHAFT ON A CEMENT SCREW CONVEYOR. HE ASKED ANOTHER EMPLOYEE TO JOG SCREW CONVEYOR INSIDE THE CONTROL ROOM. EMPLOYEE THOUGHT THAT THE OTHER EMPLO YEE DONE SO AND STARTED TO USE WRENCH TO LOOSEN SHAFT AGAIN. WHEN OTHER EMPLOYEE TURN ON SCREW CONVEYOR. THE WRENCH HIT EMPLOYEE IN THE NOSE AREA.

EE WAS ENTERING TROMMEL TO CHECK SCREENS. LEG FELL THRU HOLE THAT HAD BEEN CUT TO INSTAL SCREEN SCRAPING RIGHT LEG.

EE WAS REMOVING CHAIN FROM BELT. THE CHAIN WAS ATTACHED TO CRANE. WHEN EE 1 LET GO OF CHAIN IT SWUNG AROUND STRIKING EE 2 ON THE NOSE.

EE WAS ATTEMPTING TO LOOSEN DOOR LOCK NUT TO CRUSHER WHEN NUT BROKE LOOSE SUDDENLY CAUSING EE TO SLIP AND CUT RIGHT LEG SHIN.

12 1" BOLT HOLES IN A CIRCULAR PATTERN OF WHICH SEREAL HAD THE INTERNAL THREADS PULLED OUT LEAVING A SHARP POINTED SLIVER EXPOSED. WHILE USING A 1" TAP AND WRENCH THE EMPLOYEE'S HAND SLIPPED A ND STRUCK ONE OF THE EXPOSED THREADS.

EMPLOYEE WAS LOADING ROCK FROM PIT WALL AT QUARRY PIT. THE BUCKET HIT A FLINT BOULDER IN WALL AND STOPPED LOADER AT ONCE. OPERATOR HAD HIS SEAT BELT ON AT THE TIME BUT APPARENTLY THE SUDDEN ST OP JARRED AND TWISTED HIS BACK. INJURY BECAME A LOST TIME CASE ON 1-13-93- REASON FOR REPORTING AT THIS TIME.

EMPLOYEE WAS CUTTING BOLTS TO BE USED AS STUDS.BOLT WAS HELD IN VISE AND A HAND HELD GRINDER USED SIDEWAYS TO CUT THROUGH A 3/4" BOLT.THE GRINDING WHEEL PINCHED AND A 1/2" PIECE BROKE OFF THE WHEEL STRIKING THE EMPLOYEE ON THE UNDERSIDE OF THE FOREARM.

THE EMPLOYEE WAS WELDING INSIDE OF A MATERIAL SHAKER.HE REMOVED HIS WELDING HOOD TO CHIP AWAY SOME SLG,WHEN HE PLACED THE WELDING HOOD BACK OVER HIS FACE A SMALL PIECE OF SLAG ENTERED HIS EYE. APPARENTLY THE EMPLOYEE RUBBED HIS EYE TO A POINT THAT THE SLAG BECAME IMBEDDED.