Atlanta Plant Metal/Non-Metal

Employee was moving vibrator from railcar when they had stiffness in their lower back.

The employee was operating the locomotive when the locomotive derailed through a switch. Employee jumped off the locomotive and injured right wrist upon landing on the ground.

At approximately 10:30 a vendor installing a new HVAC unit started experiencing chest pains and felt bad. Asked co-worker to call 911 as a precaution.

Employee welding on a silo. Leaned down and bumped a pipe with their face. Lip Contusion.

Employee fell off of a skid steer at bucket height on ground while getting the hours of operation from the meter.

Employee had a recordable shift on EE's annuel hearing test greater than 25db in the 2k, 3k and 4k ranges. Employee was sent to audiologist for retest and evaluation.

The employee was pulling metal out of a gypsum pile and felt a pop in EE's back

Employee was using the bathroom preparing to go home at the end of shift. When ee felt a bite or sting on neck from an insect. The employee clocked out and start to drive home when ee had an allergic reaction causing face and arms to swell. So ee went to the emergency room for treatment.

Employee was attempting to drill out a stripped brass fitting. While starting the 1/2 inch hole the drill slipped off the gauge and contacted the webbing between the employee's thumb and index finger on left hand. The drill bit made about 1/2 inch cut.

Employee was attempting to remove a chunk blocking a control valve. Employee isolated the feed silo and opened the access port without warning. Material flushed from the silo striking employee.

Employee was adjusting plastic on pallet stretch hooder machine. While adjusting the plastic his left thumb got pinched between the feed roller and the tension roller.

Employee bumped hardhat into sign and complained of neck pain later that day.

Employee was troubleshooting an air leak on a small air cylinder. When he engaged the cylinder his finger got pinched between the cylinder head and a proximity switch.

The employee was installing a railcar vibrator when he stepped on his lanyard causing him to miss place the vibrator straining his shoulder. First aid of an ice pack was administered. After two weeks the employee felt it was not improving and requested to see a Dr, who prescribed a muscle relaxer.

Employee working on mezzanine level between floors. Employee crawled under pipes to reach work area. Surface was metal grating scattered with loose cement fragments. While crawling knee injury occurred. Employee was able to work the remainder of the day, however the knee began to swell. Employee went to physician next morning where it was confirmed to be a sprain with swelling.

Employee reported back injury while lifting safety gate at the manlift elevator. Note: Employee didn't see doctor until 11/1/2009.

Employee twisted his left ankle while getting off a fork truck.

Hand drill became bound while drilling and twisted employee's hand.

Non-chargeable death. Non employee. Truck driver found dead in sleeper of truck.

Employee was operating a hoist at the crusher building and fell 33 feet through a floor grate opening.

Cement dust got into right eye while cleaning, employee was wearing safety glasses.

Employee was struck in head while welding, by another employee handling a reinforcement beam.

Employee was looking into an air slide to observe how it was working. The dust collector pulsed and blew cement dust towards his eyes. Employee was wearing eye protection, however his eyes felt irritated. His eyes were flushed with water, he then proceeded to go to the doctor. The doctor found no abrasions on the eye and EE was able to return to work at full duty.

He was cleaning and consolidating product in the warehouse Saturday May 29th He didnt feel anything pull Sunday his back was stiff so he didn't lift anything Wednesday he came into work He was experiencing a good deal of pain and decided to take pain medication While walking up the stairs he felt a sharp pain shoot through his leg

EE was walking up the kiln. The kiln had raw material in it starting at about 110 ft. He was trying to stay on the low side of the load and while crossing a section of coating build up he stepped in a hole. The material level was deeper than the top of his boot. The hot dust entered his boot burning his foot before he could get his boot off.

EE WAS WORKING IN THE PROPER PLACE ON THE FEED PIPE. THE AIR LANCE HIT THE MILL AND TWISTED. WHEN HE TRIED TO PROTECT HIMSELF FROM THE AIR LANCEHE LOST HIS FOOTING, HE WAS STANDING ON A PILE O F MATERIAL, AND FELL FORWARD TOWARD THE MILL. HE PUT HIS HAND OUT TO STOP HIS FALL BUT PLACED IT ON THE END OF THE MILL. HIS HAND TURNED WITH THE MILL AND CAUGHT BETWEEN MILL AND FEED PIPE.

Employee attemplted to catch a bag of cement that was falling from a pallet when he noticed a sharp pain in his right shoulder.

EE WAS CHANGING ROLLER AND RIGHT THUMB STRUCK A SHARP HOLE. NOTE: EE WAS SCHEDULED FOR BEACH VACATION 7/14 - 7/18. RETURNED FROM VACATION 7/21.

EE WAS STEPPING DOWN FROM BELT AND SAID HE FELT A PULL IN LEFT KNEE.

EE WAS REPAIRING DISCHARGE SCREEN AND STRUCK METAL WITH HAMMER. METAL FRAGMENT STRUCK HIS RIGHT SIDE.

EMPLOYEE WAS EMPTYING TRASH DRUM AND FELT SEVEREPAIN IN UPPER BACK.

EMPLOYEE WAS USING JACK HAMMER THE ENTIRE SHIFT TO CLEAR CHUNKS IN AKWARD BODY POSITION. FELT MORE SEVERE PAIN THE NEXT DAY AND WANTED MEDICAL ATTENTION.

EE TWISTED HIS FOOT WHILE WALKING BESIDE SILOS.

EE HAD RIGHT EYE EXPOSED TO CEMENT WHILE CLOSINGA SHUTE DOOR AT BULK LOADING OPERATION.

EMPLOYEE HIT ELBOW ON SUPPORT BEAM WHILE SWEEPING.

EE WAS PLACING TEST ROLL OF STRETCH FILM ONTO STRETCH HOODER AND LIFTED ROLL INTO POSITION RATHER THAN USING ELECTRIC HOIST.

EMPLOYEE WAS WORKING ON MODIFYING KNINKER HOPPERAND BEGAN TO CRAMP UP/ ENTIRE BODY.

EE'S RT. ARM SHIRT SLEEVE BECAME ENTANGLED IN THE MOTOR COUPLING WHEN HE REACHED OVER THE MOTOR DRIVE COUPLING TO PURGE THE LUBE SYSTEM. DONDITION: THERE WAS NO GUARD IN PLACE. SECOND, STOP SW ITCH TOO FAR AWAY. THIRD, NO BLEEDER VALVE INSTALLED.

EE WAS CARRYING A PIECE OF PLATE AND STEPPED THROUGH A HOLE.

EE WAS WORKING ON ROTARY PACKER. WENT BEHIND PACKER TO PICK UP BAGS THAT HAD ACCUMULATED ON THE FLOOR. AS HE WAS COMING OUT FROM BEHIND THE PACKER, EE TRIPPED OVER BAG OF CEMENT LAYING ON THE FLOOR. HE TRIPPED CAUSING HIM TO LOSE HIS FOOTING AND HE FELL ON HIS LEFT SIDE. PAIN GRADUALLY WORSENED.

WHILE STEPPING ON TO PLATFORM IT TURNED OVER CAUSING EMPLOYEE TO FALL AND INJURE HIS LEFT KNEE.

DURING A MEETING WITH A CONTRACTOR, EE STOOD UP AND BUMPED HIS EYE INTO THE CONTRACTORS NOTEBOOK- CAUSING EYE ABRASION/SCRATCHED CORNEA.

EE WAS CLEANING OUT THE BOTTOM OF THE TURN HEAD WHEN HANDLE ON THE BY PASS GATE RELEASED AND HITHIM IN THE CHEST AREA BRUISING HIS RIBS.

WHILE WALKING DOWN THE STAIRS FROM THE KILN FIRING PLATFORM TO THE PRODUCTION CONFERENCE ROOM, EE MISSED HIS FOOTING AND TRIPPED ON THE BOTTOM STAIR STEP.

WHILE PUTTING GRAPHITE ON THE #4 ROLLER TO GET THE KILN TO DRAG DOWNHILL, THE EMPLOYEE TRIPPED OVER A STOOL ON THE KILN CATWALK.

EE WAS MOVING A PIECE OF 8" DUCTING. THE EE PICKED UP ONE END OF THE DUCTING AND A FELLOW EE PUSHED IN THE OTHER END OF THE DUCTING. THIS CAUSED THE EMPLOYEE'S THIRD MIDDLE FINGER TO BE SMASHE D AGAINST A HANDLE WHICH WAS WELDED TO THE TOP OF OF THE SOUTH DRAG CONVEYOR.

EMPLOYEE USING A SELF PROPELLED WORK PLATFORM AND WORKING ABOUT 10' OFF THE GROUND AND BESIDE KILN #2, REMOVING ELECTRICAL CABLE TRAY. THE KILN HAS BEEN MODIFIED BY ADDING A DOOR ON THE SIDE T O FACILITATE BURNING TIRES. THE DOOR ON THE SIDEOF THE ROTATING KILN FAILED TO SEAL COMPLETELY WHEN CLOSED AND ALLOWED HOT DUST TO FALL ON EMPLOYEE AND HE GOT DUST IN EYES.

WHILE JUMPING OFF THE LOADING DOCK OF THE FINISH SILO AREA, THE GUARD RAIL HE WAS HOLDING ONTO CAME OFF CAUSING HIM TO FALL AND HIT HIS HEAD.

EE WAS DRIVING RENTAL DUMP TRUCK LOADED WITH IRON ORE. HE WAS COMING DOWN THE HILL FROM THE STORAGE STOCK PILE WHEN THE BRAKES FAILED. EE PUSHED THE BRAKE PEDAL TO STOP THE TRUCK. THE TRUCK IN STEAD PICK UP SPEED. EE JUMPED OUT OF THE CAB CAUSING A SPRAIN TO RIGHT FOOT.

AFTER CLEANING HARDENED CEMENT MATERIALS FROM THE TURNHEAD, FEEDBOX AND TRIPPER WITH A METAL BAR, THE EMPLOYEE EXPERIENCED PAIN IN RIGHT ARM.

EE WAS CHANGING A 480 BREAKER FOR A MOTOR CONTROL CENTER. THE EE REMOVED THE BUCKET AND CHANGED THE BREAKER. THE EE THEN REPLACED THE BUCKET IN THE MOTOR CONTROL CENTER. APPARENTLY THE EE DECI DED TO RETIGHTEN ONE CONNECTOR AND SHORTED THE CONNECTOR CAUSING HIM TO BE FLASHED AND BURNED ON THE LEFT HAND, LEFT FOREARM, RIGHT EYEBROW AND TEMPLE. INVESTIGATION IS NOT COMPLETE.

THE EE PULLED THE FRONT END LOADER BESIDE THE M ECHANICAL MOBILE SHOP TO GREASE THE LOADER. THE GROUND WAS SLIPPERY FROM THE MORNING RAIN. THE EE STATES THAT HE GREASED THE LOADER ON ONE SIDE AND WAS MOVING TO THE OTHER SIDE WHEN SLIPPED.

EMPLOYEE WAS COLLECTING DUST BAGS ON TOP OF THE PACKHOUSE. THE EMPLOYEE WAS CLOSING THE DOOR 3 FT ABOVE THE TOP OF THE SILO. HE WAS HOLDING ON TO THE COVER OF AN ELECTRICAL VALVE BOX. THE COVE R CAME LOOSE CAUSING THE EMPLOYEE TO FALL 3 FT LANDING ON HIS BACK ON TOP OF THE SILO MEASURINGPORT WHICH STANDS 8 INCHES HIGH.

THE EMPLOYEE WAS RACKING IN A 4160 VOLT BREAKER FOR THE CRUSHER FOR THE CRUSHER HAMMER MILL STARTER. ON DOING SO THERE WAS AN EXPLOSION WHICH TRIPPED THE FEEDER PROTECTION RELAY. THE EXPLOSION FORCED THE BREAKER AGAINST THE ENCLOSURE DOOR. EMPLOYEE WAS THROWN BACK FROM THE ENCLOSURE DOOR, THE DOOR STRIKING HIS LEFT ARM. FORCE OF FIREBALL KNOCKED HIS HELMET OFF.

WHILE EMPLOYEE WAS MAKING REPAIRS TO A COAL MILLJOURNAL ASSEMBLY, HE TRAPPED HIS FINGER BETWEEN THE ROLLER JOURNAL ARM AND THE COAL MILL JOURNALRETURN SPRING.

CONTRACTOR EMPLOYEE WAS CUTTING OFF BOLTS IN THEKILN COOLER WITH A TORCH. DIRECTLY ABOVE IN THE KILN, ANOTHER CREW WAS BRINGING BRICKS TO OFF-LOAD IN KILN. AS EMPLOYEE WAS IN POSITION-ON HANDS AND KNEES, A CHUNK OF CASTABLE MATERIAL ON SIDE WALL OF COOLER BECAME DISLODGED AND STRUCK EMPLOYEE ON THE LOWER PART OF THE BACK OF THE HEAD.

EE WAS CLEANING OUT CLINKER COOLER WITH A WATER LANCE. AS EE APPLIED WATER WITH LANCE, STEAM AND MATERIAL BLEW OUT WITH SUFFICIENT FORCE TO KNOCK HIM TO THE GROUND. STEAM AND MATERIAL BLEW UP UNDER SAFETY HOOD AND UNDER SAFETY COAT CAUSING BURNS TO EE.

EE WAS @ THE GROUND LEVEL @ THE BULK LOADING AREA. HE HEARD THE PHONE RING @ THE OFFICE ON THE 2ND LEVEL UP. EE STARTED TO RUN UP THE STAIRS AND LOST HIS BALANCE. HE GRABBED THE HAND RAIL TO KEEP FROM FALLING. AS HE WENT FORWARD HIS SHOULDER DISLOCATED. EE HAD A DISLOCATION OF THIS R SHOULDER-OFFSITE-IN APRIL OF 1998

EE WAS CUTTING PLASTIC BANDS OFF OF A PALLET OF STRETCVH HOOD FILM ROLLS. EE STATED DURING ACCIDENT INVESTIGATION THAT HE WAS IN AN AGITATED STATE BECAUSE THE PALLET WAS BROKEN AND THIS WAS WH Y HE WAS TOLD TO TRANSFER THE ROLLS FROM THE BAD PALLET TO ANOTHER PALLET. USING A UTILITY KNIFE HE CUT TOWARDS HIMSELF AND WHEN THE RETAINING BAND WA CUT, THE KNIFE WENT INTO HIS ARM.

ON THE 6TH FLOOR OF THE PACKHOUSE (BAG PROD. AREA) HE WAS OPERATING A MOTORIZED PALLET-JACK TRYING TO MANUEVER A PALLET INTO PLACE. WHILE IN THE REVERSE MODE, HE BACKED UP INTO A SET OF PALLET S ALREADY IN PLACE. THE MOMENTUM OF THE PALLET JACK CAUGHT HIS FEET INBETWEEN THE PLACED PALLETS AND THE LOAD ON THE JACK.

WHILE ATTEMPTING TO ESTABLISH A WARM-UP FIRE IN NO. 2 KILN. RAW NATURAL GAS HAD ACCUMULATED IN KILN. THE GAS WAS IGNITED WHEN A GAS TORCH WAS INSERTED INTO THE KILN FIRING LOAD. THE INSTANTANE OUS COMBUSTION OF THE GAS OVERPRESSURIZED THE KILN AND CONNECTING ***** HEAD AND CLINKER COOLER CAUSING THE BLOWOUT OF HOT AIR AND DUST. EE WAS IN THE CLINKER COOLER BASEMENT.

DURING ROUTINE EXTRICATION OF BAGHOUSE BAGS (FILTERS) EE WAS USING CHANNEL LOCK PLIERS TO GRAB TOP OF BAC. BAG TORE AND THE FORCE HE WAS USWING ALLOWED HIS ELBOW TO STRIKE BOTTOME SIDE OF HORI ZONTAL DOORFRAME CAUSING INJURY.

EE WAS STEPPING OFF MANLIFT TO TIE OFF HIS HARNESS ON THE WEST END OF (TRAIN) CAR DUMPER. WHILE EXTENDING HIS LEFT LEG HE FELT A TWINGE IN HIS INNER THIGH AREA. HE RETREATED BACK TO THE LIFT PLATFORM AND CAME DOWN

EMPLOYEE WAS USING AN EXTENSION LADDER TO GET INTO POSITION TO ROD OUT GRIP BLOCKAGE, COMING DOWN LADDER LEG GAVE OUT CAUSING HIM TO FALL AND SLIP.

SLIPPED AND FELL IN WATER AT EAST END OF BAG PLACER.

PULLING A HOIST, STRAINED LEFT SHOULDER.

SISKEY DRIVER HAD BED OF MACK 22,000 LB DUMP TRUCK IN UP, ON DUMPING POSITION. WHEN LOAD WAS DUMPED, TRUCK PULLED FORWARD AND CAME IN CONTACT WITH ELECTRICAL POWER LINE. LOUD POP ENSUED, (TIRE S EXPLODING). DRIVER EXITED VEHICLE THEN. WEATHER WAS DRY-VISIBILITY WAS GOOD.

DUST (CEMENT) IN EYES.

EE WAS GOING ACROSS THE NEW CLINKER CONVEYOR BELT WHERE HE SLIPPED & FELL ON HIS RIGHT RAND.

FORKLIFT "NOSE-DIVED" WITH LOAD LIFTED WHILE POSITION TO LOAD TRUCK.

CUTTING 2 X 12 BOARD. SKIL SAW JUMPED FORWARD AND CUT HIS LEFT INDEX FINGER.

TWO PALLETS WERE LIFTED UP HIGH SUCH THAT IT CAN BE SET ONTO THE FLATBED. TRUCK DRIVER ASKED TO HOLD UP FOR A SECOND, WHEN THE BRAKES WERE APPLIED, THE LIFT TILTED DOWN UNTIL THE FORKS HIT THE GROUND. LOAD WAS DUMPED CAUSING FORKLIFT TO RETURN TO ALL 4 WHEELS.

EE WAS CLOSING HOPPER CAR DOOR ON BOTTOM WITH BAR. WHEN DOOR WOULD NOT CLOSE HE STOOD ON BAR, SLIPPED & FELL TO GROUND.

EMLOYEE WHO WAS TROUBESHOOTING PROXIMITY SWITCH ON PALLETIIZER BAG TABLE. AS TABLE WAS CYCLED (LOWERED), THE LEFT HAND WAS NIPPED IN THE LOWER TRACK.

EE WAS WORKING UNDERNEATH FINISHED MATERIAL SILOS TO UNPLUG AIRSLIDE. HE LOST HIS FOOTING ON A BUILD UP OF LOOSE MATERIAL & STRUCK RIGHT LEG ON NEARBY METAL STRUCTURE, RESULTILNG IN A LACERATI ON REQUIRING "6" STITCHES. DID NOT INCUR LOST TIME.

EE WAS ATTEMPTING TO GET A SPOOL OF CABLE FROM OVERHEAD SHELF. EE WAS USING ALUMINUM LADDER THAHAD NO SKID FEET AND DID NOT HAVE THE LADDER TIED OFF/SECURED. THE LADDER SLID OUT FROM UNDER EE AND EE LANDED STRAIGHT ON HIS LEFT HEEL.

EMP WAS PUTTING GRIZZLIES IN #1 COOLER. THE LASTONE WAS TIGHT GOING IN, SO THE EMP USED A HAMMERTO TRY TO DRIVE IT IN. IT THEN POPPED OUT AND HIT HIS LEGS.

EMPLOYEE WAS CLEANING LUMPS FROM THE FINISH SILO VALVE.UPON OPENING THE VALVE,HE FELT A METAL SPLINTER CUT INTO HIS LITTLE FINGER OF HIS RIGHT HAND. EMPLOYEE REPORTED INJURY TO SUPERVISOR ON 1

THE HOIST WAS BEING RUN TO TAKE UP BLOCK FOR #1 RAW SLIDESHOE EE NOTICED THAT THE BLOCK WAS SWINGING & GRABBED THE CABLE TO STEADY THE BLOCK WHILE DOING SO HIS FINGER WAS CAUGHT BETWEEN THE CA BLE & THE HOIST

EE WAS LOADING TANK TRUCK A VALVE BECAME STUCK EE TOOK 81LB SLEDGEHAMMER AND BEGAN BEATING HANDLE EE MISSED THE HANDLE AND HIT HIS HAND ON THE HANDRAIL.

CRUSHER DEPARTMENT WAS RUNNING COAL ON #1 TRIPPER BELT INTO STORAGE SILO #1. EMLOYEE WAS CLEANIGN OUT A COALBILD-UP INSIDE OF THE TRIPPER CAR CHUTE WITH A SHORT BAR WHILE THE CONVEYOR BELT WA S RUNNING. THE GLOVE ON HIS RIGHT HAND WAS CAUGHT BETWEN THE CONVEYOR BELT AND ROLLER.

EE WAS TRYING TO START TRUCK WITH A SCREWDRIVER. WHEN HE OPENED THE HOOD AND STARTED THE TRUCK IT WAS STILL IN GEAR. THE TRUCK MOVED PINNING HIM BETWEN THE 3 PIER AND 2 KILN.

EMPLOYEE WAS WORKING #3 SHALE FEEDER AND AS HE DESCENDED LADDER HE STEPPED ON A LARGE ROCK CAUSING HIM TO LOSE HIS BALANCE AND TWIST ANKLE.

EMPLOYEE STUCK HIS HAND INSIDE ON AIR COMPRESSOR & THE PISTON PNEMATICALLY CLOSED CAUSING INJURY TO HIS RIGHT HAND & ARM.

BULL GEAR FELL AND 4TH TOE ON LEFT FOOT BROKEN 2 AND 3RD TOES HAD HAIRLINE FRACTURE. SEVERE CONTUSIONS.

EMPLOYEE WAS INSPECTING THE GUDGEON BOLTS ON HOMOGENIZING SILO WITHDRAWAL SCREW. THE EMPLOYEE WAS ATTEMPTING TO STAND ON THE CONDUIT RACK FOR INSPECTION BUT MISSED THE RACK AND FELL APPROX 7' TO THE GROUND.

54736YEE STATED HE SLAMMED SHUT AN ELECTRICAL BOX AND IT BLEW UP IN HIS FACE AND ARM. ELECTRICAL BURN TO BOTH EYES AND RIGHT ARM.

EMPLOYEE WAS LOOKING IN #2 KILN & AS HE WAS TURNING TO LEAVE HE LWERED HIS FACE SHIELD & CLINKER DUST BLEW INTO HIS LEFT EYE

EMPLOYEE WAS LIFTING A BAG OF CEMENT AND FELT A SNAP IN HIS BACK. HE WAS IN SEVERE PAIN THE FOLLOWING DAY.

EMPL JUMPED OFF FEED AWAY & LANDED ON COLLECTING BELT BENDING RIGHT BIG TOE BACKWARDS.

EMPLOYEE STEPPED OUT OF THE SHOWER WITH HIGH SOLED FLIP FLOPS AND SLIPPED ON WET FLOOR CAUSING HIM TO FALL AND HIT THE BACK OF HIS HEAD.

HURT BACK FROM JERKED AROUND IN LOADER

EMPLOYEE BUMPED KNEES WHEN HE SLIPPED DOWN STAIRS COMING FROM THE RAW MILL.

WORKING ON ROTARY VALVED ON MACHINE R HAND WAS JERKED BY TENSION AND FORCED IT AGAINST A METAL PLATE HAND AND LITTLE NUMB BUT SOAKED IT THAT RIGHT AND THOUGHT IN TIME THE SWELLING WOULD GO DOW N

EMPLOYEE WAS SHOWERING AFTER HIS SHIFT AND SOMEONE FLUSHED A TOILET AND HOT WATER BURNED HIM. WHEN HE JUMPED BUT OF SHOWER HE SLIPPED AND HURT KNEE AND BACK. SENT TO EMERGENCY ROOM NEXT DAY.

EE WAS TIGHTENING BOLTS AND BENT OVER WHEN HE STOOD UP AND FELT A PULL IN HIS BACK.

STANDING UNDER KILN JACKHAMMERING GOING ON , IT FELL ON R KNEE

EMPLOYEE WAS HELPING A COWORKER MOVE A CONFERENCE TABLE TO ANOTHER ROOM AND FELT A PAIN IN HIS BACK.

SHOVELING COAL SPILLED FELT PAIN IN BACK AND LEG

AS THE EMPLOYEE WAS PARKING THE 980-B FRONT END LOADER INSIDE THE CLAY SHED, HIS RIGHT FOOT SLIPPED OFF THE STEP LADDER AND HE FELL TO THE GROUND PULLING HIS GROIN MUSCLE.

USING VACUUM HOSE TO CLEAN OUT COOLER FELT PAIN IN LOWER BACK FROM BENDING OVER

WHILE EMPL WAS LIFTING SMALL ROLL OF DRAG CHAIN HE FELT PAIN IN BACK. LS SPINE STRAIN.

EMPL REMOVING OLD D/C FROM SILOS AND STEPPED INTO SMALL HOLE IN FLOOR GRATING-BRUISED RIGHT KNEE,HEMASHROSIS,ABRASIONS.

WHILE EMPL WAS BLOWING OFF FEEDBOX WITH AIR LANCE DUST BLEW BACK INTO FACE UNDER SAFETY GLASSES INTO EYES.

EMPLOYEE WAS USING A SLEDGEHAMMER WHILE STANDING ON A HANDRAIL WORKING OVERHEAD. HIS FOOT SLIPPED, CAUSING HIM TOHIT HIS LOWER BACK ON THE RAIL. CONTUSION RT. LUMBAR AREA, STRAIN LOWER DORSAL AND UPPER 1-S SPINE.

EE WAS USING A JACKHAMMER ON 12-=6-89 AND ON 12-7-89 HE FELT A MUSCLE PULL IN THE GROIN THAT COULD HAVE BEEN TRIGGERED FROM THE JACKHAMMER.

EMPLOYEE WAS RESTACKING A BAG OF CEMENT AND SLIPPED ON WET FLOOR CAUSING A STRAIN IN HIS LOWER BACK.

EMPLOYEE WAS CHANGING MOTOR AND SLIPPED ON WET DUST ON THE FLOOR HURTING HIS BACK.

EMPLOYEE SLIPPED ON A SMALL OBJECT & FELL TO GROUND TWISTING HIS RT KNEE-SPRAINED

EMPL WAS MOVING A BOX OF EMPTY BAGS TO BAG PLACER AND BACKED TOO CLOSE AND BUMPED HAND AGAINST BAG GUIDE RAIL AND BAG PLACER CUTTING FINER ON ROUGH JOINT ON BAG GUIDE RAIL L HAND MIDDLE FINGER LACERATION NEEDED STITCHES

3 MECH REPLACING WORN OUT BUCKET ELEVATOR HEAD TRACTION ASSEMBLY...INVOLVED 3 PCS LIFTING APPARATUS-2 CHAIN COME-ALONGS,MAIN OVERHEAD CABLE HOIST.2 MECH DISASSEMBLING WHEN 1 CHAIN BROKE CAUSIN G ELEVATOR TO FALL PINCHING THEIR HANDS BETWEEN CHAIN AND BUCKET WHEEL.

3 MECH REPLACING WORN OUT BUCKET ELEVATOR HEAD TRACTION ASSEMBLY...INVOLVED 3 PCS LIFTING APPARATUS-2 CHAIN COME-ALONGS,MAIN OVERHEAD CABLE HOIST.2 MECH DISASSEMBLING WHEN 1 CHAIN BROKE CAUSIN G ELEVATOR TO FALL PINCHING THEIR HANDS BETWEEN CHAIN AND BUCKET WHEEL.

EMPLOYEE WAS CLEANING OUT THE CRUSHER TURNHEAD THAT HAD PLUGGED UP WITH A BAR. HE SAID WHILE HE WAS CLEANING OUT THE TURNHEAD IT MOVED CAUSING THE DOOR TO FALL ON HIS LEFT HAND.

DROPPED ONE LEG DOWN THROUGH OPENING IN CATWALK/WHERE LADDER WAS.

A SECTION OF CHUTE WORK HAD BEEN REMOVED BY ANOTHER CONTRACTOR THAT LEFT A HOLE IN CATWALK THIS HOLE WASNT PROPERLY COVERUP I NAME WAS WALKING ON CATWALK & ONE LEG FELL THROUGH HOLE CAUSING HI M TO PULL THE MUSCLES IN THE OTHER LEG PULLED LIGAMENTS

WHILE GRINDING OVER HEAD THE GRINDER HUNG UP THIS CAUSED THE DISC TO COME BACK & HIT HIM IN THE FOREHEAD MINOR CUT TO FOREHEAD 8 STICHES

CHIPPING WELD & GOT A PIECE OF METAL IN EYE HAD SAFETY GLASSES ON HAD TO HAVE METAL REMOVED

EMPLOYEE WAS ASSIGNED CLEAN UP WORK AT THE BELT FEED BOX. EMPLOYEE STATES THAT HE WAS HSOVELING MATERIAL OUT FROM AROUND THE FEED BOX SOUTH SIDE WHERE HE STRUCK HIS ELBOW ON THE STRUCTIAL BEA M.

EMPL GETTING OFF MILL ROOM ELEVATOR ,FOOT SLIPPED ON LOOSE CLINKER DUST -FELT SHARP PAIN IN LOWER LEFT BACK.HISTORY OF BACK PROBLEMS

EMPLOYEE WAS STANDING ON THE DRIVE GUARD LIFTING THE BONNET OFF #4 CLINKER ELEVATOR, STEPPED OFF THE GUARD ONTO THE MOTOR AND TURNED HIS ANKLE.

WHILE EMPL WAS REMOVING D/C BAG CAGE THE BAG WAS FILLED WITH HEAVY MATERIAL THE BAG SLIPPED AND MASHED FINGER BETWEEN TUBE SHEET AND FRAME R HAND TIP OF LITTLE FINGER NAIL AVULSION

EMPL WAS PICKING UP A STARTER WEIGHING 60-65 LBS AND PULLED HIS LOWER BACK STRAIN LUMOSACRAL SPINE

EMPL WAS CHANGIONG OUT SEPARATOR BLADE AND STRAINED HIS BACK IT WAS BERY CRAMPED QUARTERS AND USED ALOT OF FORCE WITH PUSHEING AND PULLING BLAD SEVERE STRAIN L-S SPINE

EMPL STEPPED OFF EMPTY RR CAR TO SWITCH TRACKS AND TOOK 10 STEPS WHEN HE STUMBLED & FELL ON RR TIE SPRAINING LEFT KNEE...RX FELDENE FOR PAIN. DENE FOR PAIN.

EMPLOYEE WAS GOING DOWN STEPS BY THE PALLETIZER AND SLIPPED TWISTING HIS ANKLE IN THE FALL.

EMPLOYEE WAS PULLING A 8 IN SCREW FROM THE SOUTH PACKHOUSE PUMP AND THE 7/8 IN EYE PULLED OUT AND CAME BACK HITTING HIS RT INDEX FINGER

WHILE LEAVING THE BUILDING INJURED STRUCK HIS HEAD, LOST HIS BALANCE AND FELL 62' TO THE GROUND FLOOR. INJURED WAS WALKING ON A PLATFORM LEADING TO A EXTERNAL STAIRWAY.

WALKING ACROSS GRATING TO SEE IF #2 COOLER WAS RUNNING. LEFT FOOT SLIPPED AND ALL WEIGHT WENT DOWN ON LEFT KNEE.

A PIECE OF RUBBER BELT HAD BEEN LEFT ON THE FLOOR, SLIPPED ON IT AND HIT KNEE ON I-BEAM.

I.NAME WAS IN GUARD HOUSE TRYING TO OPEN WINDOW THAT WAS JAMMED BY AN EXTENSION CORD WHICH WAS LEFT BY SECURITY PERSONNEL UPON TRYING TO OPEN THE WINDOW I.NAMES HAND SLIPPED AND WENT THROUGHT THE GLASS WINDOW

SACKING BAGS WHEN MISSED LOADING TUBE ON PACKING MACHINE AND HAND HIT MACHINE.

HE WAS WATCHING BELT WHEN A BUSTED BAG OF CEMENT CAME UP BELT, HE REACHED OVER AND PICKED IT UP AND TURNED TO THROW THE BAG AWAY, WHEN PAIN CAME IN HIS BACK.

LADDER SLIPPED,CAUSING HIM TO FALL.

I.NAME WAS CHANGING OUT HIS BOTTLE OF PROPANE GAS ON HIS FORKLIFT WHEN HE FELT PAININ HIS BACK

I NAME WAS USING A WE DGE TO PUSH SCALE FROM WALL. AS HE WAS DRIVING THE WEDGE DOWN WITH HAMMER A PIECE OF WEDGE BROKE OFF HITTING HIM ON LEFT ARM

SLIPPED ON THE STAIR AND HIT HIS KNEE

I.NAME AND CO-WORKER WERE INSTALLING CHUTES INT HE CLINKER BASEMENT. COME ALONG SLIPPED, CHUTE CAME BACK HITTING INJ. IN THE RIGHT KNEE.

I NAME WAS GETTINGOFF A LOADER, AREA HAD CHUNKS OF MATERIAL ON GROUND AND HE STEPPE DON ONE, TWISTING HIS KNEE

EMPLOYEE WAS CLEANING UP DEBRIS FROM 4TH FLOOR OF MILL BLDG.A 4FTX8INX3/4IN PIECE OF PLYWOOD WAS LAYING ON FLOOR COVERING AN OPENING IN THE FLOOR GRATING EMPLOYEE PICKED PLYWOOD UP FROM ONE EN D & STEPPED FORWARD INTO THE HOLE FALLING TO LOWER LEVEL

I.NAME WAS CHANGING #2 KILN F O W BELT AFTER THE BELT WAS INSTALLED HE NOTICED A NOISE COMING FROM THE TAIL SHAFT BEARING HE WAS CHANGING THE BEARING FOR INSPECTION WITH THE T O W RUNNING A PIECE OF METAL WELDED ON THE SHAFT CAME AROUND AND CAUGHT HIS THUMB BETWEEN THE PULLEY AND THE F O W HANDLE

HE WAS RESTACKI3G BAGS OF MASON MIX WHEN HE FELT PAIN IN HIS BACK.

THE 1 RAW SYMET9O WAS MAKING ANOISE. THE MILL WAS STOPPED AND I NAME DECIDE TO CHANGE THE OIL AND CLEAN THE SYUMETRO. HE WENT THROUGH THE DOOR IN THE COVER TO INSPECT THE GEARS AND OILING TRAY HE HAD ALREADY3CHECKED THE NORTH SIDE AND HAD GONE IN THE SOUTH SIDE TO INSPECT. WHEN HE GOT ON TOP OF THE LOW SPEED GEAR HIS FOOT SLIPPED AND DROPPED DOWN TO THE LOW SPEED PINION, HITTING RI

MOVING MATERIAL3FROM LOWERATOR, TURNED TO PUT MATERIAL ON PALLET, FOOT SLIPPED ON ROLLER

THE INJURED PUN7HED HIS TIME CARD AND WAS COMING TO THE CHANGE HOUSE,STEPPED ON THE DGE OF THE SIDEWALK AND GOT OVERBALANCED AND STRAINED HIS BACK.

I.NAME WAS INVE8TIGATING IN #2 MILL. HE TURNED THE BARREL & CAUGHT HIS HAND ONT HE RESTRICTION ANGLE.

I.NAME WAS INST5LLING BELT ON BUCKET. HIS GLOVE GOT CAUGHT & IT PINCHED HIS R ING FINGER.

I.NAME WAS WALK3NG TO PICK UP HIS SAMPLES WHEN MATERIAL FELL FROM OVERHEAD.

BRICK CREW WAS 8ETTING JACKS IN KILN (THEY HOLD BRICK IN PLACE) I,NAME WAS HELPING HOLD THE PIPE IN PLACE WHILE OTHER WORKERS TIGHTENED JACKING PIPE TO THE BRICK WITH A SCREW JACK. IT WAS AT T HIS TIME I,NAME3FELT PAIN IN HIS BACK. AREA IN KILN WAS UNEVEN AND OVAL SHAPED WHICH ALWAYS CAUSED INSTANCES OF UNSURE FOOTING.

I NAME ANDFELLO4 EMPLOYEE WERE REBUILDING AN 8 INCH FULLER CEMENT PUMP THE DUST CAP THAT LOCKS THE SCREW IN PLACE WOULD NOT UNLOCK. I NAME WAS H OLDING A B&O HAMMER AGAINST THE CAPW HILE FELLO EE WAS STRIKING3IT WITH A 12 SLEDGE HAMMER. A PIECE OF METAL FROM THE DUST CAPS HATTERED STRIKING HIM IN THE RIGHT LEG.

ALLEDGEDLY HURT HIS BACK WHILE JACKHAMMERING CLINDER.

I.NAME WAS MOVI3G PUMP FROM 10 SILO TO 8 SILO WHEN HE FELT PAIN IN H IS BACK.

EMPLOYEE WAS RE1AIRING A BURST AIR HOSE, WHILE CUTTING WITH A BELT KNIFE, HE SLIPPED ON GRAVEL AND SLASHED HIS LEFT, CENTER, FRONT THIGH.

EMPLOYEE WAS RE1AIRING A BURSTED AIR HOSE WHILE CUTTING WITH A BELT KNIFE HE SLIPPED ON GRAVELS & SLASHED HIS LEFT CENTER FRONT THIGH

I NAME WAS PULL3NG A PIECE OF PLATE DOWN, HOOK PULLED LOOSE FROM THE PLATE AND HIT HIM IN THE RIGHT ELBOW.

CLAIMANT WAS WE5DING AND SOME OF THE SLAG GOT INTO HIS BOOT (HOT MUDDY SUBSTANCE) AND BURNED HIS LEFT FOOT.

HAD DROVE A SLU8E ON ABOVE PORTHOLE TILL IT GOT TIGHT. THE SLIDE STILL LIKED ABOUT 3 BEING IN ALL THE WAY. HE PROCEEDED TO REMOVE CHUNKS WHEN THE LAST ONE CAME OUT THE DUST FLUSHED BY SLIDE AND OUT PORTHO5E INTO EYES. A CHEMICAL BURN TO THE EYES.

WHILE AT WORK S7UNG BY A BEE AT THE RT UPPER ARM

I.NAME WAS CHAN1ING CLINKER SILOS AND THE GATE WAS VERY JARD TO MOVE SO HE WAS USING A BAR AS LEVERAGE WHILE STANDING ON END OF THE BAR HIS FOOT SLIPPED OFF HURTING FOOT WHEN HE LANDED ON THE FLOOR 3

EMP WAS DRIVING3A DROTT AND THE C ABLE SLIPPED

I NAME HAD SHUT3DOWN,I STARTED AROUND TO CHECK PROBLEM NOT THINKING ABOUT FORKLIFT COMMING I STEPPED AROUND I NAME INTO PATH OF FORKLIFT COMMING FROM BACK OF BUILDING .

EMPLOYEE LEFT T2E CRUSHER DEPT OT GO TO THE BATHROOM, HE WALKED UP THE RAILROAD TRACK TO THE BATHOUSE WHERE HE TRIPPED AND FELL ON HIS RIGHT SHOULDER.

I,NAME WENT TO 7HE STOREROOM TO GET A SAW BLADE, ANOTHER EMPLOYEE WAS STANDING AT THE WINDOW WITH HIS KNIFE OPEN, I,NAME REACHED OVER HIS SHOULDER TO GET THE SAW BLADE AND HIT HAND ON KNIFE BL ADE. 3

EMPLOYEE WAS AT2P THE #12 CLINKER FOW HE WAS BEATING HOPPER TO DISLODGE MATERIAL AFT ER HE FINISHED & STARTED TO LEAVE AREA HE FELT TRASH IN HIS EYE HE RUBBED IT & IT SET

ALLEGEDLY HURT 2IS BACK WHILE JACKHAMMERING CLINKER.

WHILE WORKING O3 #1 KILN ROLLER SOME RUST CAME OFF THE KILN SHELL AND FELL IN RIGHT EYE

LINING UP HOLES3IN CHUTE WITH DRIFT PIN AND HAMMER,SLIVER CAME OFF PIN.

EMPLOYEE LIFTED3A 50 LB. TOOL BOX TO PLACE IT ON TOP OF WORK BENCH RUPTURING AMBILICAL CORD CAUSING HERNIA.

WHILE PICKING U1 AN AXLE FOR THE FORKLIFT,EMPLOYEE TWISTED AND FELT A PAIN IN HIS BACK CAUSED A STRAIN TO SPINE AND BILATERAL SMALL INGUINAL HERNIA.

SLIPPED ON SOME3COATING ON THE G ROUND STRIKING HIS ARM ON KILN LINING

EMPLOYEE STATES3THAT THERE WAS A LOT OF DUST IN WORK AREA WHEN HE BEGAN COUGHING AND SPITTING UP BLOOD.

EMPLOYEE STATES3THAT SHE HAS BEEN HAVING LOWER BACK PAIN ON AND OFF SINCE HOSPITALIZATION OF 1980, SEVERE LEFT HIP PAIN FOR PAST TWO WEEKS.

WHILE WALKING ON THE SILO FLOOR EMPLOYEE SLIPPED ON THE CLINKER THAT WAS ON THE FLOOR

WHILE JACKHAMMERING CEMENT FROM AROUND DRAIN PIPE JACKHAMMER SLIPPED AND CAUGHT MIDDLE FINGER OF LEFT HAND BETWEEN PIPE AND JACKHAMMER.

EMPLOYEE SLIPPED ON AN OIL SPILL WHILE ATTEMPTING TO REGAIN HIS BALANCE HE FELT A PAIN IN HIS LOWER BACK

WHILE WORKING UNDER #2 FINISH MILL COLLECTOR BELT EMPLOYEE REACHED DOWN TO PICK P A ROLLER WHEN LIFTING IT HE FELT A CATCH IN HIS BACK

WALKING UNDER #7 CLINKER SILO,EMPL SLIPPED ON SPILLED CLINKER ON GROUND CAUSING SEVERE STRAIN OF LUMBOSACRAL SPINE.

WHILE JACK HAMMERING MATERIAL FROM BEHIND A BEAM AN AIR HOSE CAME LOOSE CAUSING JACK HAMMER TO FALL ON RIGHT FOOT. THIS CAUSED TENDERNESS AND SWELLING DORSUM RIGHT FOOT WITH OBLIQUE PROXIMAL P HALANX FIFTH TOE

WHILE SWITCHING RAIL CARS EMPLOYEE REACHED FOR A HIGHER RUNG ON THE LADDER ON THE SIDE OF THE CAR CAUSING SHOULDER TO DISLOCATE.

WHILE HAULING TRASH, EMPLOYEE SLIPPED ON A CABINET DOOR WHICH WAS LYING IN THE BED OF THE PICK UP TRUCK. THIS CAUSED A STRAIN OF THE L-S SPINE.

WHILE DISLODGING A BUILD UP FROM 1 COOLER USING A WATER LANCE, THE BUILD UP FELL CAUSING BACK PRESSURE TO FALL OUT OF THE COOLER. THIS IN TURN CAUSED 2ND AND 3 RD DEGREE BURNS TO ARMS AND STO MACH REMOVING KLINKER HOT ALL FELL DOWN CUASED SPALDHING EFFECT CAME HOT CLINKER HIT PERSON.

WHILE WATCHING AN EMPLOYEE REMOVE A SNOWMAN FROM 1 COOLER BACK PRESSURE CAME OUT OF COOLER BURNING FACE AND ARMS.

EE WAS REMOVING A SECTION OF PORTABLE CONVEYOR FROM #2 KILN HOOD WHEN HE TRIPPED & FELL OVER A METAL STOOL ON T HE BURNER FLOOR.

WHILE WORKING ON THE HAMMER MILL BONNET IN THE SHOP PICKED UP LIER AND STRAINED HIS BACK

GETTING LUMPS OUT OF DUST TAND AND STRAINED BACK.

EMPLOYEE WAS GOING DOWN STEPS FROM BURNER FLOOR TO LABORATORY AND SLIPPED TWISTING HIS ANKLE.

EMPLOYEE SLIPPED GOING DOWN STEPS