Chetopa Coal

EE WAS CHANGING A BATTERY WHEN HIS HAND WAS CAUGHT BETWEEN JUMPER CABLE & BATTERY

EE WAS WALKING WHEN HE TRIPPED OVER A CROSS OVER BOARD FALLING AND STRUCK BOTH KNEES AGAINST MINE FLOOR.

A ROOF FALL OCCURRED IN 2 RIGHT ENTRY SECTION 1050. THE FALL PARTIALLY COVERED ONE RAM CAR AND FULLY COVERED ANOTHER RAM CAR THE OPERATOR OF THE COVERED CAR CRAWLED OUT HE WAS NOT INJURED.

EMPLOYEE WAS OPERATING A RAM CAR WHEN HE RAN OVER A ROCK WHICH CAUSED HIM TO CHIP HIS TOOTH.

EMPLOYEE STEPPED OUT OF MANBUS AND TWISTED RIGHT KNEE.

A ROOF FALL WS FOUND ON 11-13-96 IN THE 4 RIGHT ENTRY OF SECTION 45 SOUTH.

A ROOF FALL OCCURED IN THE 10 EAST RETRN 800' OUTBY FACE. NO DAMAGE TO EQUIPMENT.

ROOF FALL OCCURRED IN THE 3 RIGHT INTAKE ENTRY OF 45 SOUTH. NO DAMAGE TO EQUIPMENT.

A ROOF FALL OCCURRED IN 2 RIGHT ENTRY "RETURN" OF SECTION 1040--NO DAMAGE TO EQUIPMENT.

A ROOF FALL WAS FOUND IN THE 45 SOUTH INTAKE AT 8:00AM ON 10/03/96-NO DAMAGE TO EQUIPMENT,DID BLOCK PRIMARY ESCAPEWAY.

EE WAS HANGING A MINER CABLE WHEN HE HURT HIS GROIN.

EMPLOYEE WAS WORKING ON CUTTER HEAD WITH A CHEATER PIPE ON HIS WRENCH WHEN THE PIPE SLIPPED AND STRUCK HIS EAR.

FALL OCCURRED ON SECTION 1040 IN PILLAR PULLING SECTION. A7 PILLAR. #604 SPAD 10+20. FALL COVERED THE CONTINUOUS MINING MACHINE.

EMPLOYEE WAS RIDING IN RAM CAR TRAILOR BEIGN PUSHED B ANOTHER CAR. WHEN THE SECOND CAR HIT THE FIRST CAR, THE EMPLOYEE HIT THE TRACTOR WALL AGAINST HIS SELF-RESCUER.

EMP WAS LOWERING A 55 GALLON DRUM OF WATER WHEN HE HURT HIS BACK.

A ROOF FALL OCCURED ON 45 SOUTH SECTION WITH NO DAMAGE TO EQUIPMENT OR PEOPLE.

A ROOF FALL OCCURRED ON 1040 SECTION WITH N0 DAMAGE TO EQUIPMENT OR PEOPLE

A ROOF FALL OCCURED IN 4515 RIGHT RETURN WITH NO DAMAGE TO EQUIPMENT.

EMPLOYEE WAS TRASH IN LOADER BUCKET WHEN OPERATOR ROLLED BUCKEY ON HIS (L) FOOT.

EMPLOYEE WAS OPERATING A MINER WHEN A RIB ROLLED ON HIS RIGHT ANKLE.

EE MOVED HIS ROOF BOLTING SEAT, HIS FOOT GOT CAUGHT UNDER IT.

EMPLOYEE GOT LEFT FOOT STUCK IN MUD. WHEN SHE PULLED IT OUT SHE TWISTED HER LEFT KNEE AND RIGHT HIP.

EMPLOYEE TRIPPED OVER A COAL PILE WHILE WALKING.

EMPLOYEE WAS LOADING A PLANETARY WHEN IT ROLLED OVER ON HIS HAND, MASHING IT BETWEEN THE PLANETARY AND THE DOLLEY CAR.

EE WAS WORKING ON A CONTINUOUS MINER WHEN A ROCK FELL AND HIT HIS BACK.

EE WAS PULLING UP PIN CABLE, WHEN HE HIT HIS HEAD AGAINST THE TOP, CAUSING HIM TO FALL, TWISTINGHIS LEFT ANKLE & HURTING HIS NECK.

SCALE ROCK FELL FROM MINE ROOF STRIKING EE ON HIS RIGHT HAND RESULTING IN LACERATION.

EMPLOYEE WAS OPENING A PLASTIC BIT LUG CONTAINED WITH POCKET KNIFE, WHEN KNIFE SLIPPED AND CUT HIS LEFT THUMB.

A ROOF FALL OCCURRED INT HE LEFT ROOM OFF OF 3 LEFT PLACE ON THE 4515 SECTION WHICH COVERED THE BONTINIOUS MINING MACHINE.

EMPLOYEE WAS UNPLUGGING A BATTERY WHEN SHE HURT HER BACK.

EMPLOYEE WAS WALKING THROUGH A CURTAIN WHEN HE HIT HIS HEAD ON A TEE BOARD.

EE WAS REMOVING SHIMS FROM TAIL ROLLER WHEN IT JUMPED UP AND CAUGHT HIS HAND BETWEEN ROLLER AND HUMPY.

EE WAS STANDING AT MOUTH OF CROSSCUT WHEN A RAM CAR STRUCK HIM.

EE WAS STRUCK IN JAW WITH ROCK BAR.

EMPLOYEE WAS STANDING IN CROSSCUT WHEN A FEEDER CABLE THAT WAS BEING PULLED BY A RAM CAR HIT HIM IN THE LEG.

A ROOF FALL OCCURRED ON 10 EAST SECTION 1 RIGHT FACE INTERESETION - NO DAMAGE TO EQUIPMENT.

A ROOF FALL OCCURRED ON 45 SOUTH SECTION - RIGHTSIDE. FACE CROSSCUT BETWEEN 2R-3R-4R - NO EQUIPMENT WAS INVOLVED.

THERE WAS A ROCK FALL ON THE LEFT SID EOF 45 SOUTH. THERE WAS NOT DAMAGE TO EQUIPMENT.

EMPLOYEE WAS WALKING WHEN SHE SLIPPED AND FELL.

EMPLOYEE WAS CARRYING BELT ROLLERS ONTHE SLOPE WHEN HE SLIPPED & FELL CAUSING THE INJURY

EE WAS CHANIGNG A BATTERY ON SCOOP, WHEN HE DROPPED THE PLUG ON HIS FOOT.

EE WAS OPERATING A ROOF BOLTER WHEN HIS THUMB GOT CAUGHT UNDER THE SEAT.

EMPLOYEE WAS CLOSING A LID ON A TRACK JEEP WHEN IT FELL ON HIS FINGER

EE WAS LIFTING A CONTINOUS MINE PANEL COVER, WHEN HE SLIPPED IN THE MUD.

EMPLOYEE WAS LIFTING BRAKE SHOES FOR MOTOR WHEN HE HURT HIS SHOULDER.

EMPLOYEE WAS BUILDING A CRIB, WHEN HE DROPPED A TIMBER ON HIS HAND.

EMPLOYEE PICKED UP TIMBERS SLIPPED ON TRACK & FELL ON ANOTHER TIMBER

A ROOF FALL ON 45 SOUTH SECTION AT THE FACE FELL ON THE CONTINUOUS MINING MACHINE

A ROOF FALL ON 85 NORTH SECTION AT PILLAR NO 236 IN THE 1ST RIGHT ENTRY FELL ON THE CONTINUOUS MINER THIS FALL DID PULL OUT ROOF BOLTS

EMPLOYEE WAS WALKING AND STEPPED ON A PIECE OF BELT LYING ON MINE FLOOR.

EMPLOYEE WAS CROSSING OVER A BELT CROSSOVER WHEN IT CAME UP ON THE OFF SIDE. EMPLOYEE JUMPED OFF AND HURT HIS LEG.

EE DROPPED A PIECE OFMETAL ON HIS FINGER CAUSING THE INJURY.

EMPLOYEE WAS BUILDING A BRATTICE WHEN HE STRUCK HIS KNEE AGAINST A BLOCK

EMPLOYEE WAS PULLING FEEDER CABLE WHEN HE HURT HIS BACK.

EMPLOYEE WAS DRAGGING WATER HOSE WHEN IT HUNG AND HURT HIS BACK.

EMPLOYEE WAS CLIMBING OUT OF RAM CAR WHEN SHE FELL AND HURT HER LEFT HAND,RIGHT ANKLE.

ROOF FALL IN 2 RIGHT ON SECTION 1040, 2000' OUTBY FACE. NO EQUIPMENT OR PEOPLE WERE INVOLVED.

INJURED STATES THAT HE WAS LOADING SOME MATERIAL WITH THE SCOOP AT THE 8525 MATERIAL POINT WHEN THE BRAKES ON THE SCOOP FAILES THE SCOOP STARTED ROLLING BACKWARDS IN TRYING TO CONTROL THE DIRECTION OF TRAVEL HE STRUCK HIS LEFT ELBOW AGAINEST THE DECK FAN COMPARTMENT CAUSING THE INJURY.

AT APPROX. 1130 AM ON 12-28-94 A ROCK FALL OCCURRED ON THE 6550 SECTION BELT LOCATION 11&40 THIS FALL WAS APPROX. 20"L X 20' W X 5 TO 6'HIGH THIS AREA WAS BOLTED WITH 36"X3/4" CONVETIONAL BOLT S THIS FALL WAS CLEANED UP AND RESUPPORTED MUSLIGATED BY MSHA INSPECTOR.

THE INJURED STATED THAT HE WAS FINISHING THE CUT BETWEEN THE #1 LEFT & #2 LEFT WITH LT. SIDE MINER WHEN A PIECE OF DRAW ROCK FELL FROM BETWEEN AROOF BOLT & THE RIBS CAUSING THE INJURY.

THE INJURED STATED THAT HE WAS UNLOADING A BATTERY CELL OUT OF THE BACK OF A RAM CAR WHEN HE EXPERIENCED A PAIN IN HIS LOWER BACK CAUSING THE INJURY.

EE STATED THAT HE WAS MAKING A REPAIR ON THE TOP SIDE OF THE #22 TRUCK JEEP WHEN HINGED ENGINE COVER FELL CATCHING HIS LEFT THUMB BETWEEN THE TOP COVER AND ENGINE COVER CAUSING INJURY.

THE INJURED STATED THAT HE WAS SHOVELING THE LOOSE COAL SPILLAGE FROM UNDER THE 10 EAST #1 BELT CONVEYOR WHEN HE STRAINED HIS RIGHT FOREARM.

AT APPROX. 12:15 PM THE #5 MINER HAD JUST COMPLETED THE FINAL PUSH OUT ON THE #86 PILLAR AND WAS BACKING OUT OF THE CUT WHEN A ROCK FALL OCCURRED ON THE CUTTING HEAD OF THE #5 MINER--(THE MINE R WILL BE RECOVERED.)

THE INJURED STATED THAT HE WAS IN THE PROCESS OF MAKING SOME ELECTRICAL CHECKS AT THE 10E #1 HEADER TRANSFORMER WHEN HE LEANED OVER TO ENGAGE THE 100 AMP/440 BREAKER WITH HIS RIGHT HAND UNAWAR E THAT THE PROTECTIVE COVER WAS MISSING FROM THETOP OF THE BREAKER. HIS RIGHT HAND CAME IN CONTACT WITH ONE OF THE LEADS CAUSING THE ELECTRICAL SHOCK.

THE INJURED STATED THAT HE WAS WALKING THE 65 N BLEEDER MAKING A WEEKLY EXAMINATION WHEN HE RUBBED HIS FOOT AGAINST A SHARP EDGE ROCK CAUSING THE INJURY.

THE INJURED STATED THAT HE WAS MOVING A BATTERY CELL AT THE END OF THE TRACK AT THE 8560 CHARGING STATION TO THE FORK LIFT WHEN HE EXPERIENCED A PAIN IN HIS LOWER BACK

THE INJURED STATED THAT HE WAS WASHING OUT THE SCRUBBER DUCK WORK ON THE #4 MINER ON 8560 SECTION WHEN HE BUMPED HIS ELBOW ON THE SIDE OF THE DUCK WORK ON THE MINER CAUSING THE INJURY.

EE STATED THAT HE WAS IN THE PROCESS OF SETTING THE LAST ROOF BOLT ON THE RIGHT SIDE IN THE FACE OF THE #3 ROOM WHEN A PIECE OF DRAW ROCK APPROX. 5' X 4' AND UP TO 4" THICK, FELL FROM THE ROOF GLANCING OFF OF THE CANOPY SHARP EDGE DOWN STRIKING ON THE TOP OF HIS FOOT BEHIND THE STEEL TOE ON HIS BOOT CAUSING THE INJURY.

EE WAS HELPING SPLICE THE 6560 SEC. BELT AT THE TAIL PIECE WHEN THE BEL CLAMPS SLIPPE AND CAUGHT EE'S LEFT HAND CAUSING THE INJURY.

THE INJURED STATED THAT HE WAS LIFTING A BATTERY CROW ON THE #2 RAM CAR IN THE 6560 CHARNIGN STATION WHEN THE EXPERIENCED A PAIN IN HIS LOWER BACK CAUSING THE INJURY.

EMPLOYEE HAD TAKEN TRACK LOCOMOTIVE TO THE 85 N #2 HEADER TO BE USED IN PULLING THE 85N #2 BELT BACK TOGETHER.EMPLOYEE HAD FOLLOWED BEHIND THE TRACK MOTOR ON HIS TRACK JEEP TO DELIVER SOME PAR TS AT THE 85 N #2 HEADER. EMPLOYEE DELIVERED ANDWAS TRAVELING BACK AND STOPPED TO PICK UP OTHERS. THE TRACK MOTOR RAN INTO THE BACK OF THE JEEP,JARRING EMP. & CAUSING INJURY. MOTOR P BRK NOT

THE INJURED STATED THAT WAS OPERTING A 820 RAM CAR TRAVELING FROM THE FEEDER TO THE LEFT SIDE OF MINER WHEN TH ERAM CAR RAN OVER A ROCK IN THE ROAD WAY ANND BOUNCE DHIS HEAD AGAINST THE CANOPY CAUSING THE INJURY.

THE INJURED WAS PINNING THE X-CUT BETWEEN THE HEEADING AND #1 RIGHT ENTRY WHEN A PIECE OF DRAW ROCK ABOUT 1"-2" THICK FELL FROM BETWEEN 2 ROOF BOLTS STRIKING ON THE BACK OF THE HEAD CAUSING TH E INJURY. ACCIDENT OCCURRED ON THE 6560 SECTION.

THE INJURED STATED HE & ANOTHER EMPLOYEE WERE PICKING UP A SPEED REDUCER TO PUT IN THE BACK OF A RAM CAR TO CARRY TO THE SECTION WHEN HE EXPERIENCED A SHARP PAIN IN HIS RIGHT SIDE.

EE STATED HE WAS DUMPING A CAR OF COAL AT THE FEEDER WHEN HE NOTICED A LARGE ROCK HAD FELL BETWEEN THE DUMPING PAN AND THE BACK OF THE RAM CAR, WHILE EE WAS IN THE PROCESS OF MOVING THE ROCK F ROM THE CAR HE EXPERIENCED A PAIN IN HIS LOWER BACK.

AT APPROX. 7:25 AM ON 9-13-93, A ROCK FALL WAS DISCOVERED IN THE #1 RT. ENTRY 24+40 ON SECTION 8515-THIS FALL OCCURRED IN THE INTERSECTION. THE SECTION FACE TRANSFORMER WAS CAUGHT IN THIS FALL -THIS FALL IS APPROX. 20' LONG,20' WIDE & 3' TO 4' HIGH. THE AREA OF THE FALL WAS BOLTED WITH 36" JENNMAR BOLTS. THE TRANSFORMER WAS RECOVERED.

THE INJURED STATED THAT HE WAS WALKING THRU THE CROSS CUT BETWEEN THE 3 & 4 LEFT ENTRY ON SEC 6565 WHEN A PEACE OF DRAW ROCK FELL FROM THE ROZY STRIKING HIM ON THE RT FOOT CAUSING THE INJURY.

THE INJURED STATED THAT HE WAS IN THE PROCESS OF CHANGING OUT HIS BATTER ON HIS RAM CAR IN THE 6565 CHARGING STATION WHEN HE SLIPPED AND FELL IN TEH BATTERY TRAY CAUSING THE INJURY.

THE INJURED STATED THAT HE WAS HELPING I.NAME CLEAN UP A ROCK FALL IN THE #1 LT ENTRY ON 8515 SECTION WHEN SLIPPED AND FELL AGAINST A SHARP EDGED ROCK CAUSING THE INJURY.

ON 9-1-93 A ROCK FALL OCCURED INTHE INTERSECTION OF #1 RT ENTRY ON SECTION 8515. THE ROOF IN THIS IS LAMINATED SAND STONE AND WAS BOLTED WITH 36" ROOF BOLTS. THIS FALL WILL NOT BE CLEANUP.

ON 8-29-93 AT APPROX. 9:45 PM THE FIRE BOSS DISCOVERED A ROCKFALL IN THE #1 LT ENTRY 19+80 ON SEC. 8515. THIS FALL IS APPROX. 65' LONG, 20' WIDE AND 8' TO 10' HIGH. THIS FELL IN THE CROSSCUT F ROM THE HDG. TO #1 LT. ENTRY. AREA OF FALL WAS BOLTED WITH 36" + 48" ROOF BOLTS. ROOF STRATA IS OF LAMINATED SANDSTONE. A 270 FORKLIFT WAS CAUGHT IN THIS ROOF FALL- THE FORK WILL RECOVER.

AT APPROX. 6:35PM ON 7/29/93 A ROCK FALL OCCURED ON THE 8515 SECTION 19 + 80 THE FALL FILL IN THE LEFT X-CUT, FROM THE BELT HDG. TO THE RIGHT X-CUT IN #1 RT. ENTRY THE FALL IS APPROX. 60' LONG , 20' WIDE AND 2' TO 5' THICK. THE ROOF STRATA IS THIS AREA IS OF COMINATED SAND STONE. THIS FALL WILL BE CLEARED UP AND RESUPPORTED - INVESTIGATED 7/30/93 BY MSHA INSPECTOR

AT APPROX. 9 AM THE 4 MINE ON SEC 6555 WAS IN THE PROCESS OF TAKING THRU 2ND CUT ON THE 352 PILLAR IN THE 3 LT ENTRY WHEN A ROCK FALL OCCURED ON THE LT SELL OF THE HEAD ON THE MINER THE MINER WAS RETRIVED FROM UNDER THE ROCK FALL AT APPROX.5 PM 6-11-93 REPORT MSHA SUB DISTRICT 11AM 6-11-93.

AT APPROX 10:40 AM A ROCK FALL OCCURED ONT EH HEAD OF THE #4-14-CM 10 CONTINUIOUS MINER ON SEC. 6555. THE MINER HAD JUST COMPLETED THE FINAL CUT ON THE #300 PILLAR AND WAS IN THE PROCESS OF B ACK OUT OF THE CUT WHEN THE ROCK FALL OCCURED. T

EE AND COWORKER HAD JUST FINISHED BOLTING THE FACE OF THE #1 LEFT ENTRY. COWORKER WAS TRAMMING THE ROOFBOLTER OUT OF THIS PLACE. EE WAS THE PROCESS OF TAKING DOWN SOME LINE CURTAIN WHEN THE PI N CABLE CAUGHT EE AND TRIPPED HIM AND HE FELL ONHIS RIGHT SIDE CAUSING THE INJURY.

THE INJURED STATED THAT HE WAS WALKING TO THE 15 SOUTH PUMPS TO RE-SET THEM AND AS PUSHING OSME PINE TREE LIMBS OUT OF THE WAY OF HIS TRUCK WHEN A PINE NEEDLE STRUCK HIM TH ELEFT EYE CAUSIGN T HE INJURY.

THE INUURED STATED THAT HE WAS WALKING UP THE 65 NORTH HEADING WHEN HE PASSED UNDER A HIGH VOLTAGE CABLE AND BRUSHED AGAINST A CABLE TIC WIRE STRIKING HIM IN HIS RIGHT EYE CAUSING THE INJURY.

THE INJURED STATED THAT HE WAS REPAIRING A WATER HOSE IN THE 8505 CHARGING STATION WHEN HE CUT HIS LEFT INDEX FINGER ON A WATER HOSE BAND.

THE INJURED AND EE HAD BEEN MAKING SOME REPAIRS ON THE 6545 SECTION FEEDER WHEN THE ACCIDENT OCCURRED EE WAS CHECKING FOR LEAKS ON A GREASE FITTING THAT SERVICES THE FEEDER PICK BREAKER WHEN T HE INTERNAL O BLEW OUT ON THE GREASE FITTING RELEASING STREAM OF GHREASE UNDER PRESURE STRUCKING EE IN HIS LEFT EYE CAUSING THE INJURY.

THE INJURED STATED THAT HE AND OTHER EMPLOYEE HAD JUST FINISHED LOADING SOME MATERIAL IN THE LOADING END OF A RAM CAR ON 8505 SECTION WHEN HE REACHED DOWN INTO THE PAN OF THE RAM CAR TO PICK U P A SLING. HE RUBBED HIS HAND ACROSS A SHARP PIECE OF METAL CAUSING THE ACCIDENT.

A ROCK FALL OCCURRED IN THE BELT HELG ON 6545 SEC. BELT 13+20. THE FALL IS APPROX. 30' LONG' WIDE AND 3' TO 4' THICK-ROOF IN THIS AREA WAS BOLTED WITH 36" JENNMAR CONVENTIAL BOLTS-THE ROOF STR ATA IN THE AREA IS OF LAMINATED SAND STONE-THIS FALL WILL BE CLEANED UP AND RESUPPORTED. ROCK FALL WAS INVESTIGATED BY MSHA INSPECTORS.

INJURED STATED THAT HE HAD BEEN MAKING SOME REPAIRS ON 6545 FEEDER WHEN HE REACHED DOWN TO PICKUP HIS TOOL BOX HE CUT HIS LEFT INDEX FINGER ON A WELDING ROD CAN CAUSING THE INJURY

38509NJURED STATED THAT HE HAD LEFT HIS RAM CAR ON 85TH FOR EXCRETORY PURPOSES WHEN A SMALL PIECE OF SCALE ROCK FELL FROM THE ROOF STRIKING HIM ON THE RIGHT SHOULDER CAUSING THE ACCIDENT.

A ROCK FALL WAS DISCOVERED BETWEEN TEH #1 & 2 ROOMS IN THE OLD 6535 ENTRY 3+75. THIS FALL IS APPROX 40' LONG, 22' WIDE AND 4'-6' HIGH. THIS FALL WILL BE CLEARED UP AND RE-SUPPORTED.

6507023-92 A ROCK FALL WAS FOUND IN THE 517 ENTRY 60 & 00 THIS FALL IS APPROX. 70FT LONG 22 WIDE AND 4-6FT HIGH THE AREA OF THE FALL WAS BOLTED WITH 36 INCH PENN MAR CONTENT ROOF BOLTS THIS FA 33025 NOT BE CLEANED UP.

THE INJURED STATED THAT HE WAS HELPING UNLOAD A VIBRATER COIL FROM THE BACK OF A PICK UP TRUCK WHEN HE TWISTED HIS RT KNEE CAUSING THE ACCIDENT OREE WENT TO THE DR HIS HIS INJURY ON 6-17-92 AN D RETURNED TO WORK EE WENT BACK TO THE DR ON 7-16-92 DR TOOK HIM OFF WORK FOR 5 DAYS.

INJ HANGING UP PIECE OF LINE CURTAIN IN #2 LT ENTRY WHEN A ROCK 3'WIDE X 5'LONG X 3-8" THICK FELL FROM BETWEEN AND AROUND A BOLTED AREA PULLING EMPL DOWN TO THE FOOTWALL CAUSING THE ACCIDENT.T HE LOOSE ROOF IN THIS AREA WAS UNDETECTED,NO SIGNS OF BREAKS.

THE INJURED STATED THAT HE WAS IN THE PROCESS OF CHANGING OUT A RAM THE BATTERY IN THE 9 CHANGING STATION WHEN BUMPED HIS HER AGAINST A FIRE SUPPRESSION SPRAY NOZZLE CAUSING THE INJURY.

THE INJURED STATED HE WAS JACKING UP A WRECKED MAN BUS WHEN THE JACK SLIPPED AND FELL AND THE JACK LEVER STRUCK HIM ON THE INSIDE OF RIGHT KNEE CAUSING INJURY.

INJ DRAGGING UP SOME PLASTIC CURTAIN IN #2 RT ENTRY ON 6535 SECTION.PASSED THROUGH DROP CURTAIN,STRUCK HEAD ON A CURTAIN BOARD CAUSING THE INJURY.DIDNT SEEK MED. ATTENTION UNTIL 3-13-92.

THE INJURED STATED THAT HE WAS WALKING FROM THE PREP-PLANT TO THE STRIP COAL HOPPER WHEN HE STEPPED IN A HOLE ALONG THE HAULAGE ROAD CAUSING THE ACCIDENT.

ROOF BOLTING WITH #9 EIMCO PINNER IN X-CUT BETWEEN HDG & 1 RT SECTION 65 NORTH.I.NAME MOVED BOOM SWING OVER LEVER THAT CONTROLES THE BOOM SWING DID NOT CENTER CAUSING BOOM TO CONTINUE TO MOVE. I.NAME CAUGHT FINGE BETWEEN 2 DRILL STEELS CAUSING INJURY.

THE INJURED WAS MAKING AN INSPECTION OF THE #9 POND BEHIND IN ROOF REFUSE PILE. WHEN HE LOST HIS FOOTING AND SLIPPED AND FELL ON A SHARP EDGED ROCK. CAUSING THE INJURY.

THE INJURED STATED THAT HE WAS IN THE PROCESS OF REMOVING A GUARD FROM MOTOR AT STRIP COAL BREAKER. GUARD WAS ALREADY PARTIALLY LOOSE IN REMOVING THE GUARD IT FELL AND CUAGHT HIS FINGER BETWE EN GUARD AND BELT STRUCTURE CAUSING THE INJURY.

INJ STATED THAT HE WAS IN PROCESS OF PLACING SECTION OF PIPE IN PIPE FUSING MACHINE WHEN PIPE HOLDING CLAM ACCIDENTALLY CLOSED & CAUGHT FINGER CAUSING INJURY.

RF FALL IN CROSS CUT 20'L 20'W 4 'TO 5' T

AT APPROX 2 PM ON 7-8-91 A ROOF FALL OCCURRED IN THE 10 EAST TRACK SLANT 41+40. THE FALL IS APPROX 30' LONG 20' WIDE AND 3' 60 4' HIGH. THE ROOF STRATA IN THE AREA IS OF SANDY SHALE. THE RO OF WS SUPPORTED WITH 48' CONVETIONAL 3/4 ROOF BOLTS. THE FALL WITH NOT BE CLEANED.

THE INJURED WAS HELPING ANOTHER EMPLOYEE ROLL OUT OF THE TRACK IN THE SLOPE BOTTOM WHEN THE BAR ROLLED BACKWARD AND CAUGHT INJUREDS FINGER BETWEEN THE BAR AND THE TRACK RAIL CAUSING THE INJURY .

FALL IN INTERSCTIONOF 2 FT 30'L 35'W 5-6' H

THE INJURED STATED THAT HE WAS KNEELING BEHIND THE PINNER IN THE #5 RT. ENTRY ON SECTION 6525 WHEN THE SCOOP CAME THROUGH THE DROP CURTAIN BEHIND THE PINNER BUCKET FIRST, CRUSHING THE INJURED BETWEEN THE SCOOP BUCKET AND THE BACK OF THE PINNER.

THE INJURED STATED THA HE WAS WALKING TO THE SECITON FROM THE END OF THE TRACK IN 65 WITH HEADING WHEN A ROCK FELL FROM THE ROOF AND STRUCK HIM ON TOP OF THE LEFT FOOT CAUSING THE INJURY.

RF FALL ON SECTION 65 NO 40' L 20' W 5' - 6' H BOLTED WITH CONV RF BOLTS WILL BE CLEANED UP

ON 04-11-91 AT APPROX 9:30PM THE SECT ION FOREMAN ON 65NO REPORTED THAT A ROOFFALL HAD OCCURED IN THE #4 RT ENTRY FACEX-CUT THE FALL IS APPROX 20FTLONG 70FTWIDE & 5-6FT HIGH THE AR3EA OF THE F ALL WAS BOLTED WITH 4X3/4XXCONVENTIONAL ROOFBOLTS THE ROOF STRATA IS OF LAMINATED & STONE THIS FALL WILL NOT BE CLEANED UP

INJURED STATED HE WAS CARRING A PIECE OF CHANNEL IRON ON HIS SHOULDER. INTO THE SHOP. WHEN HE MOVED IT TO REPOSITION IT ON HIS SHOULDER. SOME FOREIGN MATTER BLEW INTO HIS EYE CAUSING THE IN JURY.

A APPROX. 8:45 AM ON 4-2-91, A ROOF FALL OCCURRED IN TEH #2 RT. ENTRY SPAD 30+50. THIS FALL IS APPROX. 65' LONG, 22'-24' WIDE AND 5'-6' THICK. THE ROOF STRATA IN THE AREA OF THE FALL IS OF LAM INATED SAND STONE (65 NORTH SECTION). THE ROOF WAS SUPPORTED WITH 6'X3/4 CONVENTIONAL GROUTED ROOF BOLTS. THIS FALL WILL NOT BE CLEANED UP.

THE INJURED STATED THAT HE WAS CARRING A BELT ROLLER FROM A MAN BUS TO A UNI-TRAC (SCOOP) WHEN HE TRIPPED AND LOOSE HIS FOOTING DROPPING THE ROLLER ON THE MAN BUS AND CAUGHT HIS FINGER CAUSING THE INJURY.

AT APPROX. 7:00 PM ON 3-27-91, A ROOF FALL OCCURRED IN THE 65 NORTH BELT HDG. SPAD 31+70. THIS FALL IS APPROX. 50' LONG, 24' WIDE AND 6'-9' THICK. THE FALL AREA WAS BOLTED WITH 6'X3/4 CONVENTI ONAL GROUTED ROOF BOLTS. THE ROOF STRATA IN THIS AREA IS OF LAMINATED SANDSTONE. THIS FALL WILL BE CLEANED UP.

THE INJURED STATED THAT HE AND ANOTHER EMPLOYEE WERE UNLOADING A 10 HP SUBMERGIBLE PUMP OFF A MAN BUS ALONG SIDE THE 10 EAST TRACK WHEN THE PIPE ON ONE END OF THE PUMP SPLASHED WATER AND MUD I N THE INJUREDS EYES.

HELPING LOAD BLOCKS

THE INJURED STATED THAT HE WAS LOOSENING THE BOLTS ON THE CONTROL PANEL COVER ON THE #7 RAM CAR WHEN HE EXPERIENCED A PAIN IN HIS LOWER BACK.

THE INJURED WAS BUILDING SEALS ON 10 WEST.HE WAS TOPPING OFF A SEAL AND A PIECE OF ROCK KICKED OFF AND CAUGHT HIS FINGER BETWEEN THE ROCK AND A SEAL BLOCK CAUSING THE INJURY.

THE INJURED STATED THAT HE WAS IN THE PROCESS OF CHANGING A SPEED REDUCER ON AN 820 RAM CAR ON SECTION 1010, THE INJURED WAS LIFTING ONE END OF THE SPEED REDUCER WHEN FELT A PAIN IN HIS LOWER BACK.

THE INJURED STATED THAT HE HAD BEEN BURING AND WELDING FOR SEVERAL HOURS. ON THE CONTINIOUS MINER ON SECTION 6515 WHEN BE RECEIVED BURNS TO BOTH OF HIS EYES (FLASH BURNS).

I NAME STATED THAT HE WAS BLOWING A CABLE STRAIN CLAMP ON 14 CM10 MINER WHEN HE EXPERIENCED A SHARP PAIN IN HIS LEFT SHOULDER & NECK

AT APPROX 11:30 PM A ROOF FALL WAS DISCOVERED IN THE #2 RT ENTRY TO THE #3 RT ENTRY. THE ROOF FALL IS APPROX 80' LONG 20' WIDE AND 3' TO 6' THICK. THE ROOF STRATA IN THE ROOF AREA WAS SUPPORTE D WITH 36" X 3/4" CONVENTIONAL ROOF BOLTS, 8' ROOF BOLTS AND WOODEN CRIBS HAD BEEN SET AS SUPPLEMENTAL SUPPORT IN THE AREA OF THE ROOF FALL. THIS ROOF FALL WILL NOT BE CLEANED UP.

AT APPROX. 9:40 PM A ROOF FALL OCCURRED STARTING IN THE HDG CROSSCUT TO THE #2 RT ENTRY 9+60. THIS FALL IS APPROX 120' LONG AND 20' TO 30' WIDE AND 3' TO 6' THICK THE ROOF STRATA IN THE FALL A REA WAS BOLTED WITH 36" X 3/4" "B" BELL CONVENTIIONAL ROOF BOLTER THIS ROOF WILL NOT BE CLEANED UP. THIS ROOF FALL OCCURRED ON THE 3535 SECTION ID 005.

THE INJURIED STATED THAT HE WAS CARING A BAG OF CEMENT TO BUILD A BRATICE ON THE RETURN. BRATTICE LINE WHEN HE SLIPPED AND FELL CAUSING THE INJURY.

THE INJURED STATED THAT HE WAS WALKING OUT OF THE 10 EAST INTAKE ESCAPEWAY WHEN HE TRIPPED OVER A SMALL PILE OF DRAW ROCK CAUSING THE ACCIDENT.

TRAMMING RAM CAR, RAN OVER OBST. IN ROAD, HEAD AGAINST CANOPY

INJURED STATED THAT SHE WAS SHOVELING LOOSE COAL ONTO THE 10EAST BELTLINE WHEN SHE TRIPPED OVER A ROCK IN THE WALKWAY CAUSING HER TO FALL ON HER BACK CAUSING THE ACCIDENT

DISMANTLING OVER HEAD CRANE STRUCTURE,LADDER WAS LEANED ON A A-FRAME,ANCHORED ON A CONCRETE PIECE FRAME GAVE WAY CAUSING HIM TO FALL,CUTTING RIGHT ARM.

THE INJURED STATED THAT HE WAS CUTTING SOME HOLES IN A PIECE OF RUBBER BELT WITH A BELT KNIFE WHEN THE KNIFE SLIPPED AND CUT HIS LEFT THUMB CAUSING THE INJURY.

THE INJURED STATE THAT HE WAS BUILDING A BRATTICE ON THE RETURN SIDE ON 6505 SECT IN WHEN OTHER PASSED THINK THE SOAME CROSS CUT OPERATING A UNI TRAC UNAWARE EE WAS WORKING IN THE SAME CROSSCU T BECAUSE A DROP CULTERAN WAS HUNG UP BETWEEN THE AREA WHERE HE WAS WORKING WHEN THE FRONT END OF THE BUMPED INTO A STACK OF BRATTICE BLOCKS A BLOCK FELL ONTO HIS LT FOOT CAUSING THE ACCIDENT

THE INJURED STATED THAT HE WAS HELPING ANOTHER EMPLOYEE ROLL UP A SECTION OF BELT AT THE 35 SOUTH #2 HEADER WHEN HE EXPERIENCED A SHARP PAIN IN HIS LOWER BACK.

ROCK FALL OCCURRED ON THE 3525 SECTION. THIS ROCK FALL FELL IN THE INTERSECTION IN THE #1 LT. ENTRY 12+60 CROSS CUT EXTENDING THROUGH THE CROSS CUTS TO THE #3 RT. ENTRY APPROX. 240 FT LONG, 20 FT WIDE AND 4 FT TO HEIGHT UNKNOWN. THE ROOF IN THE FALL AREA HAD BEEN BOLTED WITH 4 FT & 8 FT TENSION 3/4 ROOF BOLT WOOD CRIBS HAD ALSO BEEN SET IN THE INTERSECTIONS OF THE FALL AREA. THIS R

THE INJURED STATED THAT HE WAS PUTTING IN A FRONT DRIVE SHAFT FOR THE CONVEYOR CHAIN ON THE 5 MINER ON 6505 SECTION WHEN HE TURNED AROUND TO REPOSITION HIMSELF UNAWARE HIS LEFT FOOT WAS CAUGHT BETWEEN A CRIB WHEN HE ROLLED OVER HE TWISTED HIS LEFT KNEE CAUSING THE INJURY.

THE INJURED STATED THAT HE WAS CHANGING BITS OUT OF THE FEEDER PICK BREAKER, WHEN THE ACCIDENT OCCURRED. HE WAS KNOCKING A BIT OUT OF A BIT LUG WITH A BALL PINNY HAMMER, WHEN HE STRUCK HIS LE FT THUMB WITH A HAMMER.

PUSHING AGAINST RAISEBORE MACHINE DRILL STEM FELT SHOULDER PAIN CONTINUED WORKING UNTIL 08-05-90AT WHICH TIME HE WAS LAID OFF ON 07-31-90 HE REPORTED HE WAS HAVING PROBLEMS WITH SHOULDER DRS CARE 08-07-90 UNTIL SURGERY 09-27-90

INJURED STATED HE HAD PICKED UP MINER CABLE IN #2 RIGHT ENTRY & WAS IN PROCESS OF HANGING CABLE UP WHEN HE EXPERIENCED SHARP PAIN IN LOWER BACK.

INJURED STATED THAT HE WAS HELPING I NAME HANG UP THE CABLE ON HANGER BOARDS ACROSS THE BELT HEADING WHEN HE EXPERIENCED A SHARP PAIN IN HIS LOWER BACK

THE INJURED STATED THAT E.NAME, SUPPLYHOUSE MAN WAS HELPING HIM PICK UP RIPPER CHAIN TAKE-UP ASSEMBLY FOR A 14 CM MINER TO BE PLACED ON THE WHEEL CART WHEN ONE PART OF THE CHAIN ASSEMBLY SLIPP ED, CATCHING I.NAME'S FINGER BETWEEN THE CONCRETE PAD AND THE CHAIN ASSEMBLY CAUSING THE ACCIDENT.

INJURED STATED THAT HE WAS CLIMBING UP LADDER IN OLD SHOP TO REMOVE FAN SIGNAL SWITCH WHEN HE BRUSHED AGAINST SUPPORT BEAM & GOT SOMETHING IN LT EYE CAUSING INJURY.

THE INJURED STATED THAT HE WAS LOADING 5 GALLON CANS FO OIL ONTO THE SEMI-TRAC AT THE 3515 MATERIAL POINT WHEN HE SAID THAT HE LOST HIS FOOTING AND SLIPPED AND PULLED SOMETHING IN HIS LOWER BA CK.

AT APPROXIMATELY 7:30 PM A ROCKFALL OCCURRED ON THE CUTTING HEAD ON THE #5 CONTINUOUS MINING MACHINE,WHICH HAD JUST TAKEN THE LAST CUT FROM THE #23 PILLAR.THE MINER WAS BEING OPERATED BY MEANS OF REMOTE CONTROL.THE TYPE OF MINING WAS OF SPLIT PILLAR PLAN.THE #5 MINER WAS RETRIEVED FROM THE ROCKFALL.THE ROCK FALL WAS APPROXIMATELY 20' IN LENGTH ACROSS THE HEAD OF THE MINER,THICKNESS

INJ TAKING DOWN SOME CURTAIN WITH CLAW HAMMER IN FACE OF #3 RIGHT ENTRY WHEN HAMMER SLIPPED OFF NAIL AND STRUCK HIM IN THE MOUTH CAUSING INJURY.

FIRE BOSS DISCOVERED ROCK FALL IN 1 L ENTRY 4'T, 20'L 20'W BOLTED WITH 36" CONVENT BOLTS WILL NOT BE CLEANED UP

STATEMENT FROMT HE INJURED W NAME WAS LIFTING THE CYCLONE BODY UP WITH AN ELEC HOIST TO MOVE IT OUT OF THE WAY SO AS OTHER PARTS COULD BE HOISTED UP I NAME WAS ASSISTING IN THIS TASK AND CYCLO NE BODY BECAME LODGED BETWEEN THE WALK AND THE FLORR WHEN I NAME ATTEMPTED TO PULL IT LOOSE IT TURNED OUT AND CAUGHT HIS FINGER CAUSING THE INJURY

THE INJURED STATED THAT HE AND W NAME WERE CHANGING OUT SOME DEWATERING PADS IN THE DISCHARGE END IN THE BUMP CRAL WASH BOX I NAME WAS KNOCKING THE PADS INTO PLACE WITH A HAMMER WHEN THE HAMME R GLANCED OFF OF THE SIDE OF THE WASH BOX STRIKING HIS #2 FINGER CAUSING THE INJURY

STATEMENTS FROM INJURED AND SECTION FOREMAN I NAME STATED THAT HE AND W NAME HAD JUST LOAD THE DUAL BOOM PINNER INTO THE #1 L ENTRY AND HE WAS DRILLING THE ROOF BOLT HOLE ON THE L SIDE OF THE ENTRY WHEN A PIECE A UNDETECTED SCALE ROCK FELL FROM THE ROOF INTO THE CANOPY THEN INTO THE L COAL RIB BREAKING OFF OF THE RIB STRIKING I NAME ONT HE SIDE OF HIS CAUSING THE INJURY

THE INJURED STATED THAT SHE WAS HELPING ANOTHER EMPLOYEE SOME CRIBS BLOCKS ON A RAM CAR AT THE MATERIAL POINT WHEN SHE EXPERINCED A SEVERE PAIN IN HER LOWER BACK.

THE INJURED STATED THAT HE WAS PUTTING THE RUB BAR ONTO THE SIDE OF THE #4 MINER WHEN HE EXPERIENCED A PAIN IN HIS LOWER BACK.

AT APPROX 10:30PM ON 10/8/89 THE FIRE BOSS DISCOVERED A ROCK FALL ON SECTION 3515 14+00 THE ROCK FALL FELL IN BELT HDG EXTENDING THROUGH THE CROSS CUTS FROM THE BELT HDG TO THE #2 LT ENTRY THI S ROCK FALL IS APPROX 120'L 22'W 8'T THE AREA THE FALL WAS SUPPORTED WITH 36X 3/4 B CONVENTIONAL BOLTS THE PORTION OF THE ROCK FALL IN THE BELT ENTRY WILL BE CLEANED UP AND RESUPPORTED A CONT

AT APPROX. 9-25-89 THE FIRE BOSS DISSCOVERED THAT A ROOF FAALL HAD OCCURRED IN THE INTERSECTION IN THE #2 ENTRY ON SECTION 2515. THE FALL IS APPROX. 60 FEET LONG, 18 FEET WIDE, 40 FEET HIGH T HIS FALL WILL NOT BE CLEANED UP.

AT APPROX. 5:00 AM ON 9/25/89 FOREMAN DISCOVERED THAT A ROCK FALL HAD OCCURRED IN THE #1 LT. ENTRY ON SECTION 65 NORTH-13+10 TO 14+90 THE FALL IS APPROX. 180' LONG, 22' WIDE AND 6' TO 8' THICK . THE ROOF IN THIS AREA WAS BOLTED WITH 48" TENNMAR COUNTINATION BOLTS. THIS ROOF FALL WILL NOT BE CLEANED UP.

AT APPROX 4:00PM A ROOF FALL OCCURRED IN THE BELT HEADING (SHORT BOY) ENTRY THE 3505 SECTION.THE FALL IS APPROX 60' LONG 24' WIDE AND 4'TO 6' THICK.THE ROOF STRATA WAS BOLTED 4'AND 6' JENNAR C OMBINATION ROOF BOLTS-THIS FALL WILL NOT BE CLEANED UP.

THE INJURED STATED HE WAS BURNING SOME HOLES IN A PIECE OF METAL, WHEN HE FINISHED HE DROPPED THE PIECE OF METAL ON THE FLOOR AND A SMALL PIECE OF FORIEN MATTER FLEW UP IN HIS RIGHT EYE CAUSIN G THE INJURY.

I.NAME THEN PROCEEDED OT WALK BETWEEN THE TWO RAM CARS AT WHICH TIME E.NAME BEGAN TO TRAM THE #1 RAM CAR IN THE REVERSE DIRECTION CATCHING I.NAME'S LEGS BETWEEN THE BUMPER OF THE #1 AND #4 RA M CARS CAUSING THE INJURIES. E.NAME WAS ON THE INBY SIDE OF THE DROP CURTAIN BETWEEN THE FIRST AND SECOND CROSS-CUTS AND APPARENTLY DID NOT REALIZE THAT I.NAME WAS IN THE PROCESS OF WALKING BE

I.NAME RIDING IN FRONT OF TRACK JEEP.COMING OUT 35 SO.TRACK ENTRY WHEN ACCIDENT OCCURRED.STARTED DOWNHILL AT 35 SO CURVE.STARTED APPLYING BRAKES ON JEEP UNAWARE HIS PANTS LEG HAD GOITTEM TANGL ED UP WITH THROTTLE LEVER.THIS CAUSED SPEED OF JEEP TO INCREASE.COULDNT SLOW DOWN JEEP EXCEPT TO STRIKE PARKED BUS.

AT APPROX. 730 AM THE GENERAL FOREMAN FOUND A ROOF FALL ON THE 3505 SECTION BELT LINE THIS ROOF FALL IS APPROX. 15 FT LONG 25 FT WIDE AND 4 FT THICK AND WAS BOLTED WITH 48 INCH COME OVER 3/4 I NCH ROOF BOLTS THE ROOF STRATA IN THIS AREA IS OF LANINATED SAND STONE. THIS FALL WAS CLEANED UP AND THE ROOF WAS BE SUPPORTED 36 INCH BELT CONVEYOR WAS CAUGHT IN THIS ROOF FALL.

I.NAME WAS PINNING THE ROOF IN THE #2 TR. ENTRY WHEN THE ACCIDENT OCCURRED. I.NAME HAD JUST STARTED DRILLING A ROOF BOLT HOLE AND HAD TAKEN THE SHORT DRILL, STEEL OUT OF THE HOLE AND LAYED IT AGAINST THE SIDE OF THE BOOM ON THE PINNER, UNAWARE THAT HE HAD LOOSENED THE BOTTOM OF THE DRILL STEEL ON THE TOP OF HIS LEFT FOOT. WHEN I.NAME FINISHED DRILLING THE ROOF BOLT HOLE WITH THE LO

THE INJURED STATED THAT HE WAS TRAVELING UP TO THE 35 SOUTH MATERIAL ROADWAY ON A RAM CAR WHEN THE RAM CAR PASSED THROUGH A DROP CURTAIN THE CURTAIN SLAPPED AGAINST HIS FACE STRIKING CHIN IN T HE RIGHT EYE CAUSING THE INJURY.

INJ STATED SHE WAS GETTING OUT OF MANTRIP TRIIPPED AND FELL ON R ARM BENDING IT BACK CAUSING THEE INJ.

LETTING CANOPY DOWN ON #14 BOOM PINNER.THE CANOPY HUNG ON A DRILL STEEL IN TRAY.HE REMOVED DRILL STEEL FROM BENEATH CANOPY AND IT FELL MASHING END OF INDEX FINGER ON RIGHT HAND CAUSING INJURY. SECT 3505.

THE INJURED STATED THAT HE WAS KNOCKING A BIT OUT OF THE HEAD ON THE #3 MAIN WITH A PUNCH WHEN A SMALL PIECE OF METAL CHIPPED OFF THE END OF THE PUNCH STRIKING THE INJURED IN THE CHIN CAUSING THE INJURY.

INJ WALKING AROUND END OF SCALE RAMP AT TRACK SCALE HOUSE WHEN HE LOST FOOTING.SLIPPED AND FELL STRIKING HEAD ON EDGE? OF CATWALK CAUSING INJURY.

STATEMENT FROM INJURED. THE INJURED STATED HE HAD JUST ADDED A 3' EXTENSION TO THE DRILL STEEL SO AS TO FINISH DRILLING A ROOF BOLT HOLE IN THE HIGH BOLT IN THE 3505 BELT HEADING. UNAWARE THAT HE HAD LEANED AGAINST THE BOOM LEVER, RAISING THE BOOM UP CATCHING HIS RIGHT ARM BETWEEN THE BOOM AND CANOPY CAUSING THE INJURY.

THE INJURED WAS IN THE PROCESS ON HILING A ROOF BOLT ABLE WITH 3 FT DRILL STELL IN THE BELT BLDG 3505 WHEN THE ACCIDENT OCCURRED FOR DOTY NAG STATION TO DRILL A HOLE WHEN SOME SMALL PIECE OF D RAW ROCK FELL FROM THE TOP OF THE CANOPY HIS RIGHT HAND WAS HOLDING THE DRILL STELL. THE ROTATION STARTED TURNING THE DRILL STELL PULLING HIS HAND AND THUMB AROUND THE DRILL STELL CAUSINT THE

INJURED STATED THAT HE WAS ASSISTING ANOTHER EMPL IN WELDING BELT GUARDS UP AT 3505 BELTHEAD WHEN HE RECEIVED FLASH BURNS TO BOTH EYES.

THE INJURED STATED THAT HE WAS PUTTING A CONVEYOR MOTOR ON THE #5 MINER LOCATED ON 25 NORTH WHEN HE FELL BACK ON HIS FOOT CAUSING THE INJURY.

AT APPROX. 7:15AM ON 1-25-89 IT WAS REPORTED THAT A ROOF FALL HAD OCCURRED ON THE 35 SOUTH IN THE #1 LEFT CROSS CUT EXTENDING TOTHE CROSS CUT LEADING INTO THE #4 LEFT ENTRY. THE FALL IS APPROX . 120' LONG, N' WIDE AND 10' HIGH THE AREA OF THE FALL WAS BOLTED WITH 3' AND 8' JENNEAU POINT ANCHOR ROOF BOLT THE FALL WILL NOT BE CLEANED.

THE INJURED STATED THAT HE WAS DRILLING A HOLE TO INSTALL A ROOF BOTL ON THE RIGHT SIDE OF THE ENTRY IN THE ENTRY. WHEN A SAMLL PEICE OF SCALE ROCK FELL FROM THE ROOF STRICKING HIM ON THE LEF T FOOT CAUSING THE INJURY.

AT APPROX. 7:45 AM ON 12-27-88 THE SECTION FOREMAN ON SECTION 35 SOUTH DISCOVERED A ROOF FALL IN THE #3 LT. ENTRY 15' INBY SPAD 7470. THIS FALL IS APPROX. 20' LONG 20' WIDE AND 4' THICK - RO OF STRATA IN THIS AREA IS OF XXXX SANDSTONE AND WAS BOLTED WITH 48" XXXX ROOF BOLTS AND CRIBBED INBY AND OUTBY FALL - THIS FALL WILL NOT BE CLEANED UP.

AT APPROX. 7:30AM ON 12-27-88 A ROOF FALL OCCURRED IN THE FACE. CROSSCUT IN THE BELT HDG ON SECTION 3605 THIS FALL IS APPROX. 40' WIDE 22' LONG AND 5' THICK. ROOF STRATA IS OF LANGINATED STONE AND WAS BOLTED WITH 48" --BOLTER THIS FALL WILL BE CLEANED U.

EMPLOYEE STATED THAT SHE WAS PICKING UP A ROCK THAT HAD FALLEN OFF OF THE EST BUTT WHEN SHE TRIE TO THROW IT BACK ONTO THE BELT SHE STRAINED HER RIGHT THIGH.

AT APPROXIMATELY 1030 AM ROOF FALL OCCURRED IN THE INTERSECTION IN THE #1 LEFT ENTRY ON SECTION 35 SOUTH 8 +30 THE FALL IS APPROXIMATELY 20' LONG 20' WIDE AND 4' THICK.THE ROOF STRATA INNTHE A AREA IS LAMINATED SAND STONE.THE ROOF WAS BOLTED 36" CONVENTIONAL.BOLTS-THIS FALL WILL BE CLEANED UP AND RESUPPORTED.

INJURED STATED THAT HE & I.NAME & I.NAME WERE STRETCHING OUT THE CABLE IN #1L.ENTRY WHERE THE ACCIDENT OCCURRED I.NAME WAS PULLING 160 CABLE UP THE #1 L.ENTRY WITH XXXX&I.NAME WAS POSITIONED O OUTBY WATCHING SO AS IT WOULD NOT GET HUNG UP WHEN A LOOP IN THE CABLE STARTED MOVING AS I.NAME JUMPED OVER THE CABLE TO SIGNAL I.NAME STOP PULLING THE CABLE & THE CABLE CAUGH

INJURED STATED THAT HE & ANOTHER EMPL WERE USING A BAR TO PRY TRUCK JEEP BACK ON 10 WEST TRACK WHEN HE LOST HIS FOOTING & SLIPPED DOWN & END OF BAR STUCK IN HIS RIGHT HAND CAUSING INJURY.

THE INJURED STATED THAT HE WAS TRAVELING TO THE FACE IN A 270 RAM CAR WHEN HE PASSED THROUGH A DROP CURTAIN. THE CANOPY ON THE I70 RAM CAR HUNG IN A PIECE OF 2" PLASTIC PUMP LINE CAUSING IT TO SEPERATE AND ONE END OF ITS CAME BACK STRIKING HIM UNDER THE RIGHT EYE CAUSE THE INJURY.

INJ WA> SLIDING TOP LID COVER ON CIRCUIT BREAKER. SO AS HE COULD GET TO TRIP UIT IN BOX TO CHECK IT. INJ WA> STANDING ON SIDE OF BOX AND DID NOT KNOW HE HAD HIS HAND UNDER LID CAUSING INJ.

THE INJURED STATED THAT HE HAD JUST POSITIONED HIMSELF ON THE REMOTE CONTROL CONSOL CHAIR LOCATED NEXT TO THE INBY IN THE CROSS CUT BETWEEN #2 & #3 RIGHT ENTRY AND WAS IN THE PROCESS OF TRAMM ING THE MINER BACK TO THE #29 PILLAR TO RESUME SLABKING OF THIS #29 PILLAR WHEN A PIECE OF DRAW ROCK APPROX. 3'1/2" X 4' X 1 1/2" THICK FELL FROM BETWEEN TWO ROOF BOLTS ONTO THE REMOTT CONSOL

A ROOF FALL OCCURRED IN THE BELT CROSS CUT ON SECTION EASR. THE FALL IS APPROX. 45 FEET LONG, 28 FEET WIDE, 8 DFEET THICK. THE SUPPORTED WITJ TEMP. BOLTS TIMBER CRIBS BEEN ADDED AS SUIPPLEM ENT SUPPORT AROUND OUTER EDGES WHEN OCCURRED.

AN ROOF FALL OCCURRED IN THE ENTRY ON SECTION 2454. SPAD #5140. THIS FALL WILL NOT BE CLEANED UP THE ROOF STARTED IN THE AREA IS OF LAMINATED SAND STONE THIS FALL IS APPROX. 90 FEET LONG, 24 FEET WIDE 2 FEET THICK. 60 FEET OF THIS FALL WAS BOLTED WITH BELL BOLTS.

A ROOF FALL WAS DISCODED IN THE #2 ROUTE SECTION 2550. THIS FALL WILL NOT BE CLEANED UP, THIS FALL IS APPROX. 20 FET LONG, 2/ FEET WIDE, 3 FEET THICK. ROOF SARTED THIS LOCATION IS SANDY SHAL E AND LAMITED SAND STONE AND WAS BOLTED WITH BOLTS.

A ROOF FALL OCCURRED IN THE INTERSECTION OF THE ENTRY INTO THE INTERSECTION OF THE SECTION. THIS FALL WILL NOT BE CLEANED UP THE ROOF STARTED IN THEAREA IS LAMITED SAND STONE. THE FALL WAS B OLTED WITH RESIN BOLTS. THIS FALL IS APPROX. 22 FEET WIDE, J FEET THICK.

AT APPROXIMATELY 5:00 PM ON 09-20-88 A ROOF FALL OCCURRED IN THE X-CUT BETWEEN THE #4 AND #K ROOM ENTRY.RIGHT SIDE OF THE 2545,CATCHING THE #4 JOY MINER (RENBOLT) THE FALL IS APPROX 4' THICK 1 8 TO 22' WIDE AND 50' LONG THE ROOF STRATA IS A SANDY SHADE AND WAS BOLTED WITH 36"TO 48" COMBINATION BOLTS THE MINER WAS TRAVELED REMOTELY BY ITS OWN POWER.

ON 9/19/88, A ROOF FALL WAS DISCOVERED IN THE #1 RT ENTRY IN THE OLD SHORT DOG ENTRY TO THE LEFT OF 10 EAST HEADING (WORKED OUT AREA). THE FALL IS APPROX. 3' THICK, 20' WIDE AND 24' LONG AND W AS BOLTED WITH 36" RESIN BOLTS. THE FALL WILL NOT BE CLEANED UP.

ON 9-17-88 A ROOF FALL WAS DISCOVERED IN THE #4 RT ENTRY ON SECTION 10 E. SPAD 14 AND 79. THIS FAL IS APPROX 30 L, 24' W. AND 5' TO 6' THICK. ROOF STRATA IN AREA IS OF SANDY SHALE. ROOF BOLT ED WITH 48" BOLTS. FALL WILL NOT BE CLEANED UP .

INJURED EMPL STATED THAT HE WAS CLEANING SOME ROCKS OUT OF GRIZZLY AT PREPLANT WHEN ROCK FELL ON HIS HAND CAUSING INJURY.

STATEMENT FROM I.NAME & INJURED I.NAME WAS MOVING DUEL BOOM PINNER INTO THE FACE OF #1 LT ENTRY NO.OF #2 LEFT ENTRY UNAWARE THAT I.NAME HAD POSITION HIMSELF BEHIND CURTAIN IN T HIS PLACE & MO VING PINNER INTO THIS THE CONTROLS & CANOPY (RT.SIDE) CAUGHT I.NAME AGAINST THE R IB CAUSING THE INJURY

THE INJURY STATED THAT HE WAS WALKING BACK FROM THE FACE TO THE FEEDER AND PASSED THROUGH A DROPWATER WHERE THE TOOLS CAR WAS PUSHED AND JAMMED HIS HEAD AGAINST THE CAR CAUSING THE INJURY.

AT APPROX 7:00 AM ON 7/21/88 ROO FALL OCCURRED ON #1 RT ENTRY NEW SECTION 35 SO 2+80 THIS FALL IS APPROX 50' LONG 20' WIDE & 5'TO 8' THICK ROOF IN THIS AREA WAS SUPPORTED WITH 4' & 8' JEN MAR RESIN BOLTS. THIS FALL WILL NOT BE CLEANED UP.

AT APPROX. 8 A.M. THE FIRE BOSS DISCOVERED A ROCK FALL IN THE INTAKE. ESCAPEWAY ON THE EASRT SECTION. THIS FALL IS APPROX. 65 FEET LONG, 22 FEET WIDE, 8 FEET HIGH. THE FALL WAS LOCATED IN T HE 5 WEST HALLWAY.

AT APPROX 6:30 AM ON 6-28-88 THE FIRE BOSS DISCOVERED A ROCK FALL IN THE CROSS CUT BETWEEN #2 AN D#3 LT ENTRY ON SECTION 10 EAST (12+10) THIS FALL IS APPROX 6' LONG 24' WIDE AND 6'-8' THICK ROOF IN THIS AREA WAS BOLTED WITH 36" AND 48" POINT ANCHOR ROOF BOLTS

ON 6/26/88 IN #3 LEFT ENTRY ON SECTION 2550 ROOF FALL WAS DISCOVERED BY FIRE BOSS AT APPROX 7:30 AM THIS FALL IS APPROX 40' LONG, 24' WIDE & 8' HIGH. AREA WAS BOLTED WITH 4'X6' POINT ANCHO R BOLTS. ROOF FALL WILL NOT BE CLEANED UP.

AT APPROX 9:30 PM ON 6/24/88 ROOF FALL OCCURRED IN #2LT FACE ENTRY ON SECTION 2550. THIS FALL IS APPROX 60' LONG, 20' WIDE & 6' TO 8' THICK. AREA WAS BOLTED WITH POINT ANCHOR BOLTS. ON 6/26 /88 IN #3 LEFT ENTRY ON SECTION 2550 ROOF FALL WAS DISCOVERED BY FIRE BOSS AT APPROX 7:30 AM FALL IS APPROX 40' LONG 24' WIDE & 8' HIGH & WAS

THE INJURED STATED HE WAS ATTEMPTING TO SHARPEN A RATCHET(WHILE IN OFFICE).WHILE SHARPENING MACHETE SLIPPED CAUSING THE EMPLOYEE TO CUT THIRD FINGER ON RIGHT HAND.