Florida Power Development LLC Metal/Non-Metal

Employee removed glasses to view settings on survey device. Afterwards, EE attempted to don safety glasses, misjudged the clearance and inadvertently inserted the end of the safety glasses into the corner of left eye. A witness informed the injured employee that blood was accumulated in the corner of left eye.

Lifting beam into place. When the rigging bottomed out the employee lifted the beam to unhook the choker.

Emp stepped off bay and R foot went down into channel between two bays causing employee to lose balance falling forward. Emp attempted to break fall with hands which slipped off bay causing face to impact horizontal support channel. Emp injuries which included facial fracture of mouth will require 1 tooth to be extracted, 22 stitches to Lip, puncture to R thumb and bruised R knee.

Spreader bar was dropped in between tubes to be turned 90 degrees to open gap between tubes for cleaning. Spreader bar was caught between 1st tube in bundle and tube below. Employee tried to remove stuck spreader bar by using force with his arms agitating back and forth without success. Employee retrieved larger spreader bar and separated tube bundle to remove stuck spreader bar.

Worker was moving a piece of steel rod and it cut his right forearm

Employee was moving 4 schedule 40 carbon steel pipe (35lbs) into position at a receiver tank. The employee he felt pain in his stomach but he thought it was something he ate. The employee reported his injury the next day via phone (Sunday 06/23/13) and was taken to the doctor on Monday for examination on Monday 06/24/13 for examination and was diagnosed a Umbilical hernia.

While erecting structural steel components, an employee was using a sleever bar to align holes in preparation for inserting bolts. The employee was pulling the bar with both hands when it became dislodged from the connection point. The sleever bar struck the employee in the face at the nose-cheek juncture. Employee suffered a laceration and broken nose.

Employee was laying steel checkered plate at the hog tower when he felt a pop in his left arm.

A millwright was assembling a drag chain by using a crane to stretch out sections of the chain so the next section could be attached to the end. While a section of one of the drag chains was hanging from the crane the rigging came off of the hook and the load fell striking an employee.

Employee was driving rebar stake to establish danger barricade around an excavation. He picked up too high and missed the stake pinching his finger between rebar and driver.

After installing a girder beam in the ESP, all rigging was removed from the crane. The employee was attempting to remove a tag line from the girder beam. He pulled on the rope to see if it was entangled or still tied. The rope broke and the employee fell backwards 10' until his PFAS arrested his fall. During his descent his left foot impacted a walkboard fracturing his left ankle.

Insect bite, cellulitis (soft tissue infection).

Employee was cleaning an area for a weld repair. Employee right eye became irritated with what felt like a foreign object.

EE was welding and stopped to replace the welding rod, picked up his hood and something got in his left eye.

Operating front end loader in coal yard. While scooping a load of coal, tried to roll the bucket back, rear end went up in air. Coal pile gave way, rear end came down hard . The air seat came down and bottomed out. Injured his lower back.

Employee was mowing lawn around office building, grass & dust was blowing around. Later in the day he noticed something in his left eye. He washed out his eye & it felt better, later in the evening he felt something in his eye again. Dust in left eye, irritated , Foreign body left eye, Corneal abrasion. Employee has achieved M.M.I. with no functional limitations.

Oil gun was attempting to retract from the boiler, when it jammed against the igniter. EE lifted up on the igniter to free the oil gun and the gun shot back and pinched his right hand ring finger.

Two employees were moving the Sandpiper Portable Sump Pump out from between the Sump Pumps 1A & 1B. One was pushing the Pump forward while the other was lifting it up with the chain hoist. The Pump started to roll toward Sump Pump 1A; injured tried to hold it back, trapped his (R) hand smashing pinky finger between pumps.

Working on Coal ramp with loader, was bouncing in loader. Back started hurting around end of shift.

Employee was repairing tube leaks on reheat header. we were using the pneumatic grinder to clean tubes and dirt blew in his left eye.

EE WAS CLEANING OUT THE HOPPERS ON THE BAGHOUSE.EE OPENED THE DOOR AND THE MATERIAL WAS PACKED IN TIGHT. WHEN THE MATERIAL WAS BROKE IT STARTED FLOWING OUT, AND THE HOT MATERIAL WENT DOWN INDIDE HIS BOOTS.

EE WAS LEAVING BOILER THRU CHAIN CONVEYOR. HE STEPPED FROM TOP LEVEL ONTO BOTTOM SCAFFOLD BAORD. THE BOARD BROKE AND HE FELL 6 FEET INTO CHAIN CONVEYOR.

EE LOST HIS FOOTING WALKING ALONG RAILROAD TRESSELL GOING TO HIS CAR.

EE WAS SWEEPING, REMOVING DIRT FROM UNDER TABLE WITH A BROOM, WHEN HE FELT SOMETHING IN HIS EYE.

EE WAS PREPARING A BOILER TUBE TO REPAIR A CRACK IN THE TUBE. AIR FROM THE PNEUMATIC GRINDER BLEW DUST UP UNDER HIS WELDING HOOD.

EE WAS STEPPING OVER PIPE & CAUGHT HIS FOOT & FELL LANDING ON HIS RIGHT HAND. EE WAS DISTRACTED & WAS NOT PAYING ATTENTION TO HIS FOOTING.

EE WAS MOVING A 450# DRUM OF OIL ACROSS SHOP FLOOR WHEN HE CAME TO A NARROW OPEING BETWEEN THE 4160 ROOM, DRUM CART ROLLED OVER A SEAM ON THE FLOOR. DRUM CART HIT THE SEAM IN THE FLOOR & JARRE D THE CATCH LOOSE FROM THE DRUM, ALLOWING DRUM TO MOVE UP & FORWARD.

EE STEPPED ON A PIECE OF AROMA FLEX (BLOCK FROM INSULATION), THAT WAS PARTLY UNDER WATER AND HADMUD ON IT. EE SLIPPED AND FELL ON HIS RT. HIP, WHEN HE FELL HE HIT THE LOCKER ALONG THE POWER HOUSE AND WALL.

KNEELING ON CONCRETE, SCRAPING GASKET SURFACES. IMPROPER KNEELING & BENDING PROCEDURES.

EE WAS INSIDE CATIOR VESSEL ON PT #1 TAKING FINGERS OFF DISTRIBUTION READER FOR REPAIRS. AS HE WAS PUSHING HIS WAY OUT OF THE VESSEL, RE CUT HIS LEFT HAND ON THE STAINLESS STEEL DISTRICUTION H EADER.

HAND WAS IN PRONE POSITION WHEN PIN WAS PULLED HAND WAS PINCHED IN BETWEEN A PINCH POINT IN MOWER.

EMPLOYEES WERE CUTTING AND WELDING PATCHES ON SEWAGE TREATMENT PLANT.

WORKING ON GATHERING SCREW AT E-40 BAGHOUSE. CONTRIBUTING FACTOR WAS HEAT.

THE AREA WHERE EE FELL WAS SLIPPERY WITH ALGAE GROWING, BECAUSE OF A STOPPED UP DRAIN.

KNOCKER WRENCH FELL FROM LEDGE OF EXPADSHION JOINT AND DOWN ONTO TOP OF FOOT.

DO NOT KNOW EXACTLY EE FELT PAIN WHEN HE WAS WALKING DOWN FRON E-40 BAGHOUSE.

WORKING ON FLY ASH VALVE 141 HAD END COVER OFF AND WAS APPLYING AIR PRESSURE TO VALVE WHEN VALE PISTON FLEW OUT HITTING RIGHT HAND AND CUTTING RIGHT THUMB.

EMPLOYEE WAS STANDING ON THE FENDER OF THE LOADER WASHING THE WINDOW. HE WAS HOLDING ON TO SIDE MIRROR WITH ONE HAND. HE LOST HIS BALANCE AND FELL TO THE GROUND. HE WAS COMPLAINING OF A HURT B ACK AND SORE LEG.

DRILLING HOLE AT AN ANGLE WHEN DRILL LOCKED UP AND CAUGHT EE'S HAND BETWEEN STEEL.

CLIMBING DOWN BETWEEN BOILER AND CATWALK. EE PUT HIS KNEE ON A ROUND PIECE OF SKIM CAUSING TO GET HIS FOOTING BELOW WHEN HE FELT HIS KNEE POP.

LIFTING CHUTE OUT OF MILL WHEN RIGGING WAS BINDING. LET OFF RIGGING TO ADJUST STRAP CHUTE WAS WEDGED BUT WHEN ADJUSTING STRAP IT FELL ON HAND.

TRYING TO LINE UP SPRINGS IN PULVERIZER BY TURNING COUPLING. HE FELT SHARP PAIN IN CHEST. HE AT THAT TIME DID NOT REPORT ACCIDENT BECAUSE HE DID NOT THINK IT WAS THAT BAD.

TAKING CENTER POST FROM D COAL MILL & CENTER POST FELL FROM MILL LANDING ON UPPER CHEST

EMPLOYEE WAS ASSISTING ANOTHER EMPLOYEE WHO WAS MOVING A WELDING MACHINE. THE INJURED EMPLOYEE WAS CARRYING THE MAJORITY OF THE LOAD. THE INJURED EMPLOYEE FELT A PAIN IN HIS GROIN AREA.

EMPLOYEE WAS USING A PIPE WRENCH & STRAINED HIS BACK. EMPLOYEE DID NOT REPORT INCIDENT TO SUPERVISOR UNTIL 7/25/00 & DID NOT REQUEST TREATMENT UNTIL 7/28/00.

EE WAS COMING OUT OF A SPACE & THE PERSON ABOVE HIM DID NOT SEE HIM THERE. THE PERSON ABOVE OPENED THE BUILER DOOR AND HOT GLY ASH FELL ONTO THE INJURED EE'S NECK & SMALL SECTION OF HIS RIGHT ARM.

EE WENT TO GET THE ATTENTION OF A CONTRACTOR. THE CONTRACTOR TURNED AROUND WHILE UNHOOKING A GAINT GUN AND EE WAS SPRAYED WITH PAINT.

EE SLIPPED WHEN HE PLACED HIS FOT ON THE EDGE OF A HOPPER & BUMPED HIS SHIN. EE DID NOT REPORT INJURY UNTIL 4/29. DR.'S NOTE DID NOT INDICATE DIAGNOSIS. WE WERE UNABLE TO DETERMINE (THRU DR.) UNTIL 5/9/00.

EMPLOYEE WAS LAYING DOWN TO LOOK AT SOMETHING AND THE NEXT DAY HE SAID THAT HIS RIBS WERE SORE. IT WAS NOT REPORTED UNTIL 3-27-2000.

EE WAS WALKING OUT OF FIRST AID CLASS WHEN SOMEONE STUPPED IN FRONT OF HIM AND HE STEPPED WRONG, TWISING HIS KNEE.

EE WAS MOVING BATTERIES ALONG A SHELF. HE HAD DONE EVERYTHING HE COULD TO MAKE THE JOB EASIER, BUT AT SOME POINT HE STRAINED HIMSELF TOO HARD. THE INCIDENT WAS NOT REPORTED TO HIS SUPERVISOR U NTIL 3-10-2000& EE DID NOT WANT MEDICAL ATTENTION UNTIL 3-13-2000.

EE WAS USING A WRENCH WHEN IT SLIPPED AND HIS HAND HIT A PIECE OF SHEET METAL WHICH CUT HIS RIGHT INDEX FINGER.

WHILE HELPING ANTOHER EMPLOYEE MOVE SOMETHING HE FLT A SLIGHT BURINING SENSATION IN HIS GROIN AREA. IT WENT AWAY THE NEXT DAY, BUT CME BACK. EE DID NTO REQUEST MEDICAL TREATMENT UNTIL 3-16 U NTIL SEEN BY A DR, IT WAS BELIEVED TO BE A GROIN STRAIN.

EE STOOD UP AND HIT HIS HEAD ON A BEAM. HE WAS WORKING ON A TEMPORARY PLATFORM.

THE EE WAS TAKING MEASUREMENTS AND STEPPED IN A DRAIN HOLE.

EE WAS CLEANING HOPPER WITH A ROD WHEN THE MATERIAL SHIFTED AND HE HIT HIS RIBS ALONG THE HANDRAIL.

EMPLOYEE SLIPPED AND TWISTED HIS KNEE, LEFT.

EE STRAINED HIS BACK WHILE UNLOADING TRAILER. THIS WAS AN INCIDENT THAT THE EE DID NOT WANT MEDICAL TREATMENT UNTIL 6-28-99-WHEN SAFETY DEPT WAS NOTIFIED.

EE WAS SORTING CROSSTIES WHEN HE TWISTED THE WRONG WAY & HURT HIS BACK DID NOT NOTIFY MGMT UNTIL5/25/99 HE WAS ATTEMPTING TO MOVE LARGE AWKARD OBJECTS W/O HELP

EE WAS LIFTING OBJECTS TOO HEAVY FOR ONE PERSON. ANOTHER EE NOTICED AND WENT TO HELP HIM FROM THEN ON.

EE WAS IN A AREA WHERE THEY WERE REBUILDING TUBES AND WAS NOT WEARING PPE. HIS WRIST CAUGHT THE END OF A TUBE WHERE IT CUT IT.

EMPLOYEE WAS WALKING UP STAIRS THAT HAD MATERIALBUILD UP ON IT, WHEN HE TWISTED HIS RIGHT KNEE. INJURY WAS REPORTED TO HIS SUPERVISOR ON 03/30/99 AND TO THE SAFETY DEPARTMENT ON 04/02/99.

EE WAS HANDLING SCRAP METAL WITHOUT GLOVES AND CUT HIS RIGHT HAND.

EE WAS WORKING IN TIGHT SPOT. WHEN HE WAS GETTING OUT HE TWISTED WRONG & STRAINED HIS BACK

EE WAS BY THE BOILER WHEN SOME CLINKER FELL INSIDE THE BOILER RUPTURING A STEAM PIPE

WHLE REBRICKING THE KILN, EE HANDED A BRICK UP TO THE CONTRACTOR. THE CONTRACTOR LOST HOLD & IT FELL ON TO EE'S HAND WHILE IT WAS ON THE PALLET OF BRICKS.

EE WAS TAKING A SHORT CUT AND ENDED UP LOSING HIS BALANCE. HE FELL AND LANDED ON HIS LEFT SHOULDER.

EE TOOK SHORT CUT WHEN EXITING A BOBCAT. HE PLACED HIS FOOT ON THE BUCKET, SLIPPED AND FELL.

EE WAS TRYING TO HELP COWORKERS WITH A PROJECT. THEY WERE POPPING OUT SMALL BALLS USED FOR A GRINDING AID THAT HAD GOTTEN STUCK. EE USED OLD METHODS, AND WAS POPPING THEM OUT BY HAND. ONE FLEW BACK AND HIT HIS RIGHT EYE GLASS LENSE.

EE (ALONG WITH COWORKERS) WERE MOVING A TEMPORARY SERVICE & TRANSFORMER. WHILE MOVING THE PIECE HE FELT A MUSCLE PULL IN HIS ABDOMEN. IT WAS DIAGNOSED AS A HERNIA

EE'S WERE MOVING A PLATFORM TO PERFORM SOME WORK & EE DID NOT SEE PINCHPOINT. FINGER (LEFT RING FINGER) WAS CRUSHED & LACERATED. SURGERY WAS PERFORMED & THE FINGER WAS REPAIRED

EE WAS SPLICING A BELT (CONVEYOR) AND FELT HIS RIGHT SHOULDER POP

A DRAFT CAUSED SOME PARTIVCLES IN THE AIR TO GET INTO THE EE'S LEFT EYE.

EMPLOYEE WAS RUNNING TO CLEAR FALLING CLINKER AND TRIPPED/SLIPPED AND FELL OVER SOME STUDS THAT WERE LEFT IN THE FLOOR. (STUDS HAVE NOW BEEN REMOVED.)

EMPLOYEE WAS IN THE PROCESS OF TURNING OFF THE C/K BELT IN ORDER TO TAKE A C/K SAMPLE. THE AREA WAS DIMLY LIT AND HE STEPPED HALF ON AND HALF OFF AN OBJECT ON THE GROUND AND TWISTED HIS KNEE.

EE SLIPPED AND FELL ON SOME MOSS LANDING ON HIS TAILBONE

COVERING CLINKER PILE WITH TARP. ON A VERY WINDY DAY, WIND CAUGHT THE TARP AND EE FELL ON HIS RIGHT SHOULDER.

HE REPORTED HE WAS HAVING BACK PAIN TO HIS WUPERVISOR. HE SAID HE STRAINED HIS BACK.

EE WAS WALKING DOWN STAIRS ON ABOUT THE 4TH STEP HIS FOOT SLIPPED STRAIGHT AHEAD AND HE FELL DOWN. HECAUGHT HIMSELF WITH HIS HANDS HIS LEFT HAND WAS PUSHED BACKWARD HE WAS TORN CARTILAGE AND 2 SMALL FRACTURES NO DEBRIS OR OIL WAS FOUND OR THE STAIRS.

EE WAS SUPERVISING WELDER ON AN OPERATION WHICH DID NOT HAVE THE APPROPRIATE ARAC SHIELD IN PLACE. DURING THE COURSE OF THE OPERATION EE RECEIVED MINOR WELDING BURNS TO THE EYES.

EMPLOYEE WAS GRINDING PIPE WHEN WHEEL CAUGHT THREDS & THREW HIS FINGER INTO GUARD.

EMPLOYEE WAS IN THE SILO CLEANING THE BUILD UP OF MATERIAL. WHEN HE FINISHED, HE WAS WALKING ON THE MATERIAL. WHILE WALKING ON THE MATERIAL, IT BROKE LOOSE, CAUSING HIM TO LOSE HIS BALANCE & H IT HIS LEG ON THE SIDE OF THE SILO.

EMPLOYEE WAS CLEANING COUPON-MACHINED BEVELED PIPE WITH MINERAL SPIRITS. AS HIS RIGHT HAND CAME DOWN AROUND THE PIPE, BEVELED PIPE EDGE CUT THROUGH THE RUBBER GLOVE, CUTTING HIS RIGHT LITTLE F INGER.

EMPLOYEE WAS STRIPPING WIRE WITH A POCKET KNIFE HOLDING CABLE WITH LEFT HAND RIGHT HAND SLIPPED CUTTING LEFT PALM.

CARRYING BOOKS DOWN CONTROL ROOM STAIRS, SLIPPED TO NEXT-TO-LAST STEP ABOVE LANDING, HIT LEFT RIB CAGE ON LOWER HAND RIAL.

ADJUSTING GRATING ON TOP OF GRIZZLEY WHEN HAND WAS STRUCK BY OTHER EMPLOYEE WITH A HAMMER

WIPING OFF AIR CONDITIONER HAND PASSED OVER METAL PIPE CUT R PALM

ATTEMPTING TO REPAIR MACHINE HAND SLIPPED HIT FAN

RIGHT PINKIE FINGER WAS PINCHED BETWEEN SHEAVE AND CABLE GUIDE OF CRANE CABLE BLOCK.

WHILE INPECTING V BELTS HIS FINGERS BECAME PINCHED BETWEEN BELTS AND SHEAVE.

EMPLOYEE CHANGED POSITION TO GET A BETTER VIEW INSIDE THE TURBINE HOUSING & BUMPED HIS KNEE ON THE CONCRETE FOUNDATION

EMPLOYEE WAS CLEANING SUBMERGED CHAIN CONVEYOR BOTTOM OF BOILER, STANDING ON FLOOR HOLDING LADDER, WHILE COWORKER ON LADDER WAS HAMMERING ON BOILER TO LOOSEN MATERIAL. SUDDEN DISLODGE OF MATER IAL CAME DOWN. IMMENSE CLOUD OF LIME DUST/WATER ENGULFING EMPLOYEE. EMPLOYEE WAS WEARING ALL REQUIRED SAFETY GEAR.

EMPLOYEE WAS CLEANING SUBMERGED CHAIN CONVEYOR BOTTOM OF BOILER, STANDING ON LADDER USING HAMMER BANGING ON THE SIDE OF THE BOILER TO LOOSEN MATERIAL ON TRANSITION CHUTE. SUDDEN DISCHARGE OF M ATERIAL CAME DOWN CAUSING IMMENSE CLOUD OF LIME.LIME/LIME WATER ENGULFED EMPLOYEE. EMPLOYEE WAS WEARING ALL REQUIRED SAFETY GEAR.

EMPLOYEE STRAINED HIS BACK BY MOVING A BOX HE WAS INSTRUCTED TO DISASSEMBLE.

CHANGING AIR HOSE ON CLYCLONES HOT MATERIAL DISCAHRGED FROM AROUND CLEAN OUT AIR LANCE.

I.NAME WAS ASSSIGNED TO HELP CLEAN OUT SUBMERGED CHAIN CONVEYOR. HOT MATERIAL PUFFED OUT OF THE ACCESS DOOR AND CAME IN CONTACT WITH HIS ARMS AND NECK.

HOLDING A PRYBAR ON A CHAIN WHEN THE CHAIN BROKE & HIT THE EMPLOYEES FINGER

TONGUE OF WELDER FELL ON EMPLOYEES FOOT WHEN HE TRIED TO MOUNT IT ON THE BUMPER OF A PICKUP EMPLOYEES LEFT FOOT WAS BROKEN

EMPLOYEE WAS CUTTING TAPE FROM A VACUUM HOSE WHEN THE KNIFE SLIPPED, CUTTING HIM ON THE FOREARM. INJURY BECAME INFECTED ON 3-6-89 AND WAS UNABLE TO WORK.

PRYING PC OF STEEL FORM CYCLONE WHEN IT CAME LOOSE PINCHED THUMB AGAISNT PC OF ANGLE IRON CUTTING TENDON IN HIS THUMB

MATERIAL SAMPLER PLUGGED UP. EMPLOYEE THOUGHT THE MOTOR WAS TRIPPED OUT BUT IT WAS NOT. HE STUCK HIS RIGHT HAND IN SCREW TO CHECK FOR MATERIAL. THE SCREW WAS STILL TURNING CAUSING THE TIP OF H ISRIGHT MIDDLE FINGER TO BE CUT OFF.

PAYLOADER GOING IN FORWARD MOTION TO FEED HOPPER AT CPL A03 BELT.GROUNDMAN WALKED INTO RIGHT CORNER OF BUCKET KNOCKING HIM TO GROUND CAUSING RIGHT FRONT WHEEL TO RUN OVER LEGS.CONDITIONS WERE DRY & SUNNY.

EMPLOYEE WAS DRIVING A BEARING RACE OFF WITH A HARD FACED HAMMER THE BEARING RACE SPLIT AND A PIECE OF IT FLEW OFF AND IMBEDDED IN HIS ARM

EMPLOYEE WAS UTILIZING A CHIPPING HAMMER AS A DRIFT PIN TO LINE UP A BOLT HOLE ON A COVER PLATE HE STRUCK THE CHIPPING HAMMER WITH A BALLPEEN HAMMER WHICH CAUSED THE WEDGE END OF THE CHIPPING HAMMER TO FRAGMENT OFF AND IMBEDD IN HIS LEFT FOREARM

EMPLOYEE WAS RIGGING A CROSSTIE THAT WAS TO BE REMOVED FROM A PILE OF SCRAP LUMBER. HE STEPPED BACK ONTO A BOARD WITH A NAIL IN IT WHICH PUNCTURED HIS BOOT AND FOOT.

EMPLOYEE WAS STRIPPING ELECTRICAL CABLE WITH A POCKET KNIFE. HIS STROKES WERE TOWARD HIS LEFT HAND WHICH WAS HOLDING THE CABLE. UPON HIS LAST STROKE, THE KNIFE CAME INTO CONTACT WITH HIS LEFT THUMB THUS CAUSING THE LACERATION.

EMPLOYEE WAS ATTACHING A MULTI-METER TEST LEAD TO B PHASE OF A 480 VOLT CONTROL UNIT WHEN IT CONTACTED THE STEEL STRUCTURE HOUSING TH E ELECTRICAL APPARATUS THUS CAUSING A PHASE TO GROUND CIR CUIT RESULTING IN A VERY LARGE AND EXTREMELY HOT ELECTRICAL FLASH OR ARC

EMPLOYEE WAS HOLDING MULTI-METER TEST LEAD TO A&C PHASE OF A 480 VOLT CONTROL UNIT. HIS PARTNER ATTEMPTED TO ATTACH A LEAD TO B PHASE WHICH THEN CONTACTED THE STEEL STRUCTURE HOUSING THE ELECT RICAL APPARATUS THUS CAUSING PHASE TO GROUND CIRCUIT RESULTING IN A VERY LARGE AND EXTREMELY HOT ELECTRICAL FLASH OR ARC TO BE PRODUCED.

EMPLOYEE WAS USING AN AERSOL SOLVENT TO CLEAN A PIECE OFINSTRUMENTATION. THE CAN OF SOLVENT WAS FULL BUT LITTLE FLOW THROUGH THE EXTENSION NOXZZLE. EMPLOYEE SHOOK THE CAN ONCE AGAIN AND SOLVEN THAT WAS REMAINSING IN EXTENSION TUBE CAME OUT AND SPLASHED INTO HIS EYE CAUSING THE CHEMCIAL BURN.

EMP WS HANDLING GAS CYLINDERS WHEN ONE ROLLED ON HIS LITTLE FINGER.

EMP WAS CLOSING A VALVE WHN HE COMPLETED THIS TASK HE STARTED TO EXIT THIS CONFINED AREA, HIS BACK CAME IN CONTACT WITH A HOT PIPE.

EMP WA> ADJUSTING OUR CHLORINATOR SYSTE M WHEN HE ACCIDENTLY INHALED CHLORINE GAS THAT WAS LEAKKING.

EMP WAS SITTING ON THE BACK OF A FORKLIFT ACTING AS A COUNTER WEIGHT. THE FORKLIFT MOVED CAUSING THE EMP TO FALL HE TRIED TO GRAB ONTO THE CONOPY AND HE CUT HIS HAND ON A PC.O F METAL

EMPLOYEE WAS OPERA TING A MOTOR CONTROL VALVE IN A MANUAL STATE LOCALLY MANUAL LEVER KICKED OUT & THE HAND WHEEL SPUN BACKWARDS THE HANDLE ON THE HAND WHEEL STRUCK HIS RT.WRIST BREAKING IT

EMPLOYEE WAS OPERATING A PNEUMATIC IMPACT WRENCH WITHOUT WEARING A FACE SHIELF ONLY SAFETY GLASSES METAL PARTICLES FINE WERE BEING BLOW AROUND AND FEW LODGED IN HIS LEFT EYE.

EMPLOYEE WAS OPERATING A PNEUMATIC IMPACT WRENCH WITH-OUT WEARING A FACE-SHIELD, ONLY SAFETY GLASES. METAL PARTICLES (FINE) WERE BEING BLOWN AROUND AND A FEW LODGED IN HIS RIGHT EYE.

EMPLOYEE WAS ATTEMPTING TO CHIP AWAY THE REMAING STUB OF A SLEDGE HAMMER HANDLE THAT WAS STELL AFFIXED INTO THE SLEDGE HEAD WITH A WELDING SLAG CHIPPING HAMMER THE HAND THAT WAS STABLIZING THE SLEDGE HEAD SLIPPED AS HE WAS COMMING ON DOWN STROKE WITH THE CHIPPING HAMMER THUS CONTACTING HIS LEFT WRIST PUNCTURING IT.

EMPLOYEE CLIMBED OVER A HAND RAIL AND LOWERED HIMSELF DOWN TO A ROOF TO CLEAN UP SOME KILN FEED SPILLAGE WHEN HE LOWERED HIMSELF DOWN TO A ROOF TO CLEAN UP SOME KILN FEED SPILLAGE WHEN HE LOWE RED HIMSELF AS FAR AS HE COULD GO HE LEFT GO AND DROPPED THE REST OF THE WAY DOWN 4 FT INTO A PILE OF HOT 125 & F KILN FEED. THE KILN FEED ENTERED HIS RIGHT BOOT AND CAUSED BURNS 2ND DEGREE T

EMPLOYEE WAS USING A LARGE HIGH SPEED PEDESTAL GRINDER TO GRIND EDGE DOWN ON A 1INCH WASHER HIS HAND SLIPPED & HIS FINGER CAME IN CONTACT WITH GRINDING WHEEL CAUSING INJURY TO HIS RT.FINGER

EMPLOYEE WAS DESCENDING THE STEPS BY A BELT CONVEYOR. WHEN THE EMPLOYEE MADE/TOOK HIS LAST STEP ONTO THE GROUND, HE OVERTREAD HIS ANKLE ON AN UNEVEN PORTION OF THAT GROUND.

EMPLOYEE WAS EN7ERING A BUILDING FROMTHE OUTSIDE A STRONG GUST OF WIND BLEW THE DOOR SHUT ON EMPLOYEES FINGERS CAUSING THIRD PHALANGE OF MIDDLE FINGER ON RT.HAND TO BECOME BROKEN

EMPLOYEE WAS IN3PROCESS OF OPENING AN ACCESS PORT ON LEVEL OF A 4 STATGE PREHEATGER FOR A CEMENT KILN AS HE OPENED THE DOOR HOT KILN FEED SPEWED OUT & CAME IN CONTACT WITH HIS LEFT & RT.HANDS WRISTS & FOREAR4S CAUSING 1ST & 2ND DEGREE BURNS

THE EMPLOYEE WA8 USING HIGH PRESSURE WATER DIRECTED AT A BUILD-UP OF HOT KILN FEED ON THE FEED SHELF OF THE KILN. WHEN THE WATER WAS APPLIED TO THE BUILD-UP, A BLOW-BACK OF HOT KILN FEED OCCUR RED. THE EMPLOY9E WAS WEARING A PROXIMITY SUIT, BUT SOME OF THE HOT FEED FELL INTO HIS LEFT GLOVE CAUSING 2ND & 3RD DEGREE BURNS TO THE WRIST AND HAND.

EMP WAS WELDING3A PIECE OF SHEET METAL WHEN IT F ELL DOWN ONTO HIS SAFETY BOOT. THE METAL PENITRATED THE BOOT JUST BEHIND THE SAFETY TOE, AND LACERATED HIS TOE

THE EMPLOYEE WA8 STANDING BELOW AND TO THE SIDE OF A BURNER PIPE FOR A KILN THAT WAS BEING LOWERED TO THE GROUND FOR REPAIRS. THE HOISTING DEVICE/COME-A-LONG FAILED TO HOLD THE LOAD AND THE PI PE FELL TO THE 1ROUND STRIKING THE EMPLOYEE ON THE LEFT SHOULDER AND RIB AREA.

EMPLOYEE WAS LI0TING A WELDING ROD OVEN WHICH WAS VERY BULKY AND WEIGHED APPROX. 70 LBS. AS HE WAS MANUVERING AROUND SOME STATIONARY OBJECTS, HE APPARENTLY SUFFERED A BACK STRAIN TO THE LOWER LUMBAR REGION 2F THE BACK.

EMPLOYEE WAS ST5NDING OUTSIDE OF HANDRAIL AND WAS ATTEMPTING TO UNHOOK A COMEALONG FROM A LOAD HE WAS HELPING TO RIG THIS LOAD AS HE REACHED TO UNHOOK THE COMEALONG THE LOAD MOVED CAUSING HIM TO LOOSE HIS B5LANCE AND FALL APPROX 15 FT

EMPLOYEE WAS LI0TING A DISCHARGE HOSE FROM A PUMP WHEN HIS FOOTING LET GO AND HE SLIPPED WITH THE HOSE ON HIS SHOULDER. THE TWISTING MOTION OF HIS FALL STRAINED/SPRAINED HIS LWOER LUMBAR MUSCL ES. 3

EMPLOYEE WAS AS8ISTING IN SETTING A SECTION OF STEEL WHEN IT KICKED OUT STRICKING HIM IN THE CHEST AREA AND HEAD.

DRIVING DOWN HA6L ROAD IN 651 CAT PAN WHEN VEHICLE HIT A PILE OF ROCK LEFT BY AN INDEPENDENT HAULER VEHICLE VEERED RT EMPLOYEE LURCHED FORWARD HITTING HEAD ON THE STEERING WHEEL

OPERATOR DROVE 2OE TO THE EXCAVATION AND AS HEW WAS TURNING AROUND TO OPERATE THE BUCKET THE BACK HOE APPEARED TO JUMP OFF INTO THE HOLE AND PINNED I.NAME CAUSING HIS INJURY

EMPLOYEE WAS GR3NDING ON A PIPE LINE THAT IS UNDER CONSTRUCTION, EPOXY RESIN DUST FROM THE COATING ON THE PIPE LINE WAS LIBERATED INTO THE AMBIENT AIR CAUSING MINOR SECOND. MAJOR FIRST DEGREE BURNS TO THE T3SSUE SURROUNDING THE EYES.

EMPLOYEE WAS GO3NG TO THE BATHROOM IN A PORTO JOHN WHEN HE WAS SPLASHED AROUND HIS GENILTILES WITH THE CHEMICAL DECOMPOSER CONTAINED WITHIN THE HOLDING TANK. THIS CAUSED SEVERE FIRST, MINOR SE COND DEGREE BUR3S IN THIS AREA. TAKEN TO THE DOCTOR FOR TREATMENT.

EMPL SETTING DO4N LARGE PIECE OF LAB EQUIP AS HE RETURNED TO FULL ERECT POSITION,RIGHT WRIST CAME IN CONTACT WITH SHARP CORNER PIECE OF METAL CAUSING LACERATION OF RIGHT WRIST.

OPERATOR GOT TO2 CLOSE TO THE EDGE OF A SLOPED AREA HE MANEUVERED THE EQUIPMENT SO IT WAS FACING UPHILL INSTEAD OF WAITING TO BE PULLED UP AND OUT BY A DOZER HE GAVE IT THROTTLE AND TURNED THE WHEEL THIS IS 5N ARTICULATED MACHINE THE MACHINE LURCHED AND ROLLED ONTO ITS SIDE THE OPERATOR JUMPED FREE AND CLEAR OF THE MACHINE

EMPLOYEE WAS AL5EGEDLY STANDING ON TUBBING DECK WHEN A KNOCKER WRENCH FELL FROM AN UNKNOWN HIEGTH STRIKING THE EMPLOYEE OF THE LEFT FOOT.

MIXING CEMENT T2 PATCH HOLES IN A CONCRETE PIPE A GUST OF WIND BLEW DRY CEMENT PARTICLES INTO EYE THE EMPLOYEE WAS WEARING SAFETY GALSSES W/SIDE SHIELDS

EMPLOYEE WAS AL5EGEDLY STANDING ON AN APPROX. 9 FT WALL GIVING SIGNALS TO A CRANE. AFTER COMPLETING WORK WITH CRANE EMPLOYEE ALLEGEDLY TURNED AROUND AND STEPPED OFF THE WALL.

THE BOOM OF THE3CHERRY PICKER INADVERTENTLY CAME IN CONTACT WITH LIVE ELECTRICAL WIRES BELOW MENTIONED EMP WAS ATTEMPTING TO CONNECT THE END OF A CHOKER TO THE HOOK AND WAS ELECTROCUTED THE CH CHERRY PICKER W5S GROUNDED OFF

EMPLOYEE WAS AL5EGEDLY HANGING PIPE SUPPORT IN PLACE WHEN HE ALLEDGEDLY FELT SOMETHING PULL IN HIS BACK

EMPLOYEE WSA ALLEGEDLY MOVING OUT OF HE WAY OF ALLEGGED FALLING MATERIAL FROM LEVEL ABOVE EMPLOYEE ALLEGEDLY BECAME ENTANGLED IN WELDING LEADS & THEN ALLEGEDLY STRUCK KNEE AGAINST FAN HOUSING WE HAVE APPROX SIX EMPLOYEES THAT WILL DISPUTE ANY MATERIAL FELL INTO ALLEGED INJURED EMPLOYEES AREA

EMPL PULLING 3-TON CHAIN FALL 30\ FROM ONE LEVEL TO ANOTHER AND SLIPPED ON GREASE AREA TWISTING LOWER BACK.

EMPLOYEE WAS CLEANING TURBIN FLOOR OF SCRAP MATERIAL. HE LIFTED A PIECE OF PLYWOOD WHICH HADBEEN REINFORCED WITH 2X12 LUMBER FORTHE PURPOSE OF COVERING A HOLE. HE TURNED HIS HEAD, SAID SOMETHI NG TO ANOTHER EMPLOYEE AND FELL THROUGH THE OPENING HE HAD UNCOVERED.

EMPLOYEE WAS UNLOADING BARRELS OF STEEL BALLS FROM THE BACK OF A FLAT BED TRUCK WHEN HE SLIPPED ONSOME OIL OR GREASE CAUSING HIM TO FALL TO THE BED OF THE TRUCK.

EMPLOYEE WAS CLEANING MATERIAL FROM AREA AROUND FLOP GATE. GATE STUCK & HE WAS USING A JACK HAMMER TO LOOSEN GATE. HAMMER SLIPPED & GATE KICKED BACK, PINNING HIS RIGHT HAND BETWEEN HAMMER & ED GE OF FRAME.

EMPL WALKING TOWARD BOILER MAKER SHOP ON ACCESS HEAD WHEN HE WALKED INTO 3\\ TUBE THAT WAS OVERLAPPED STACK OF TUBING 5-6\\ CAUSING LACERATION JUST ABOVE LEFT EYE REQ 5 STITCHES.