Grove Stone Quarry Metal/Non-Metal

EE was using a pry bar to unclog rip rap that was hung in a chute. When the rock came loose it fell onto the EE's hand smashing their left index finger. The EE was treated and received 3 sutures in the finger making this reportable to MSHA.

EE was attempting to put a sheave on a pulley shaft that had been cut, the EE cut EE's left middle finger on a bur on the shaft. EE was taken to the urgent care where EE received stitches in EE's finger, making this reportable to MSHA.

EE was loading a hydraulic cylinder and was holding by the head cap, when EE dropped the cylinder to the floor the barrel collapsed mashing EE's fingers in between the eye and head cap. This resulted in broken fingers on both hands. EE has splints on 3 different fingers making this accident reportable.

EE was walking across flat ground after a rain event and slipped in mud and fell landing on EE's left shoulder. EE was still hurting and went to get checked out and was released to light duty until on 3/20/23 until EE has surgery. EE's job duty has changed, and EE will miss time for recovery making this accident reportable.

EE was in the manlift helping to repair a guard. The manlift basket got caught on a piece of metal and then jolted loose. When it came loose, the EE fell against the handrail, hit lower back and pinched EE's sciatic nerve. The doctor placed EE on light duty.

EE was assisting forklift to turnover cheekplate. The forklift operator got the ckeekplate picked up on one side to about 85 degrees. The EE began to push on the cheekplate. The forks lost tension under the plate, popped up, knocked the EE's hand loose from the plate, and the plate fell back on the EE's left, lower leg causing a fracture of the two bones.

EE was lifting a bucket of ABC with EE's right hand and placed it on a hand truck. EE felt a sharp pain in EE's sternum. This was on Friday. On Monday, it was not any better, so EE went to the doctor and was diagnosed with a muscle strain and placed on light duty, thus making the incident reportable.

The EE was working on Tower No. 1. The chute over the scalping screen stopped up and spilled rock out of the chute. The EE saw the material begin to fall, and a 6" rock hit EE in the back causing a Contusion. Doctor put EE on restricted duty for one week, thus causing the accident to be reportable.

Employee was positioning HDPE pipe in fusion machine. 300' length of 18" pipe was suspended from a trackhoe by a chain & being aligned by a rough terrain forklift. Employee attempted to make a final adjustment in the pipe alignment & placed hand between the pipes. At that time the pipe shifted in the chain & entrapped the employee's fingers. Gloves were being worn.

Standing on the trucks ladder, slipped, hit chest on the ladder, contusion right front wall of thorax

The EE was moving sand with the 988 loader when the joystick locked into the autoraise position with a full bucket of sand. Due to the incline of the pile, this raised the counter weight and rear wheels. The operator kicked the loader out and this slammed the bucket to the ground. This threw the operator into the ROPS and caused a 3" gash in head and a concussion.

EE was putting a boom/stick pin in the long reach trackhoe. EE bent over to line up the hole and when EE raised back up, EE felt something "snap" in the lower part of EE's back. Ended up just being spasms resulting in restricted duty causing the incident to be reportable.

The EE was working on a haul truck from a step ladder. EE stepped from the ladder with left foot and left the right foot on the rung of the ladder. This twisted EE's left knee and EE heard a pop. EE was unable to put any weight on it. EE was diagnosed with a sprained knee and was put on light duty until further checkups.

EE was working on a skid steer loader. Upon exiting the loader, stepped down to the concrete floor and left knee twisted, causing fall to the floor. The EE went to the doctor and was placed on light duty for a sprain. Employee has a follow-up appointment on 3/26/18, where they should be released to full duty.

The EE was operating a R-65 Haul truck and smelled rotten eggs, so rolled up the windows. A little later the battery exploded and ruptured EE's right ear drum. Upon further investigation, the alternator was over charging the battery which caused the explosion. The EE was restricted for five days.

The EE was cutting a section off of a conveyor belt using a razor knife. The knife slipped, cutting the EE on the Left Wrist. No Stitches were required, but on 9/16/16, the EE went back to the doctor for a follow up and they prescribed antibiotics for fear of infection, thus making the accident reportable.

EE was attempting to put a pin back into a Euclid R-90 Haul Truck. Employee was using air tools. During the process, got something in left eye. The next day employee went to the doctor and they had to remove a piece of metal from eye. Employee was wearing safety glasses at the time of the accident.

There was a trespasser on the border of our property who jumped off an elevated surface, head first into the Swannanoa River. The trespasser hit head on the river bottom and was taken away by paramedics. We do not know the extent of injuries due to privacy laws. EMS told us that injured was coherent and answering questions on way to hospital, so we did not immediately report.

EE was welding in a chute. He finished with one welding rod and attempted to throw it onto a shelf close to him. When he threw it, it bounced off a plate and came back into his left shoe burning his leg. Accident occurred on 7/11/13, but EE did not feel need to go to doctor until 7/23/13, which is when we got diagnosis of 3rd degree burns, making it reportable.

The contract employee was notching a board that he was replacing on the office wall. As he was cutting the board, the knife slipped off of the board and hit his right thumb. The employee went to urgent care and the laceration required 5 stitches, thereby making the accident reportable. Name of contractor is Osada Construction

EE was helping to install new guard on a conveyor drive. While in the seated position, the EE felt a pain in his groin area. He stood up and felt a knot in his right groin area. Went to the doctor and had a hernia. The doctor restricted activity for 10 days to no lifting over 10 lbs.

EE was changing a hydraulic hose on a rock breaker. He was pulling with one wrench and pushing with another. When he broke the connection loose, the wrench came back and hit him in the mouth. He bruised his lip and chipped his front tooth

EE was cleaning up on Scalping tower when a rock came off screen and struck EE on Back. Doctor said the EE's back was bruised. Came back to work. On 4/21/09, EE went back to doctor for checkup and doctor scheduled physical therapy for bruise. Started physical therapy (ten sessions) on 4/27/09, and accident became reportable on 4/27/2009.

EE claims that he finished his shift, got down off of his haul truck and was walking to the shop to put his keys away when he must have stepped on a round rock and twisted his ankle. Reported it to supervisor two days later. Went to the doctor two days after that and doctor took out of work due to sprained ankle.

The EE was guiding a euclid onto a low boy, when he slipped and fell on the trailer rail. At the time the EE said he was fine. Since, he has come back and said that he has had problems with his back. After going to the doctor, the doctor said he needed surgery. The accident became reportable on March 10, 2008 after having surgery and becoming lost time.

The employee was cleaning out a clogged chute leading off the primary crusher. Once unclogged, the employee walked away from the chute and rock fell from the top of the chute, striking the employee's left hand.

Employee was closing the tailgate on a company pick up truck when he caught his right hand index finger between the right side of the gate and side of the bed.

EE WAS CUTTING A PLASTIC TIE WITH A POCKET KNIFE. THE KNIFE SLIPPED WHEN THE TIE WAS CUT THROUGH, CUTTING EE'S RIGHT INDEX FINGER.

EE was unloading a d-7 dozer at the quarry. He was reconnecting the angle arm on the blade prior to unloaidng and felt a burning in his lower back.

Employee was cleaning a crusher shaft with a wire wheel grinder. He nelt down on the floor and bumped the grinder, sending it into his right leg.

EE WAS HOLDING 2 PIECES OF 11/2 STEEL WATER PIPEWHILE ANOTHER EE WAS TIGHTENING THEM. WHEN THE INJ EE RAISED UP HE FELT A SHARP PAIN IN HIS LEFTSIDE (EE TO SEE SURGEON ON 6/20/01)

SERVICE MAN WAS REMOVING LRI & LRO WHEEL & TIRE ASSEMBLY HAD REMOVED OUTSIDE ASSEMBLY WAS REMOVING SPACER WHEN IT FELL TO THE GROUND BOUNCED PINNING RING FINGER ON RIGHT HAND BETWEEN SPACER BA ND AND CRANE ON OTR TRUCK.

WHILE WORKING IN A DITCH, SQUATTED DOWN TO ASSIST ANOTHER JOURNEYMANB AND HIT A PIECE OF 2" WATER -PIPE THAT WAS PROTRUDING FORM SIDE OF DITCH.

EE WAS MOVING A WINDOW THAT WAS BROKEN. GLASS FELL OUT OF THE WINDOW, CUTTING HIM ON THE LEFT LEG BENEATH THE KNEE.

EE WAS OPENING A METAL GATE AND CAUGHT HIS RIGHT THUMB IN A PINCHPOINT.

REMOVING NYLON CABLE TIES FROM BROKEN GREASELINEON G-525 R-90 TRUCK WITH POCKET KNIFE. KNIFE SLIPPED CUTTING BETWEEN MIDDLE FINGERS ON LEFT HAND

EE WAS CLEARING BRUSH ALONG HAUL ROAD AND WHILE CUTTING A TREE, THE CHAINSAW KICKED BACK AND STRUCK HIS KNEE.

EE WAS CLEANING UP TOP DECK ON TOWER WHEN ASKED TO HELP FLIP OVER THE FRONT GUARD CHUTE ON THE SCREENING UNTI WHICH WEIGHS APPROX. 200 LBS THE EE FAILED TO LET CHUTE RELEASE ON THE RELEASE SIG NAL WHEN PULLED TO THE PIVOT POINT HIS FINGER WAS CAUGHT BETWEEN THE CHUTE AND UPRIGHT BEAM.

EMPLOYEE WAS HELPING TO INSTALL ENGINE IN THE R-22 EUCLID REAR DUMP TRUCK AND WAS ALIGNING BOLT HOLES TO MOTOR SUPPORT FRAMES. EMPLOYEE WAS FEELING FOR ALIGNMENT WITH FINGER WHEN PRY-BAR SLIP PED AND ENGINE SHIFTED AND CUT-OFF TIP OF FINGER.

WAS ASSISTING IN LIFTING A 55 GAL. BARREL OF ANTI FREEZE TO AN UPWRIGHT POSITION FROM ITS SIDE AND HURT HIS BACK.

EE WAS PRYING OR AN R-35 REAR DUMP LEAF SPRING WHEN THE PRY BAR SLIPPED AND CRAZED ACROSS EE S RT FORHEAD WHICH RESULTED INA CLEAR CUT WHICH REQUIRED 6 STITCHES. EE RETURNED TO WORK THE SAME D AY.

EE WELDED 3INX3INX4FT ANGLE ACROSS OPENING OF FEEDER PAN WHILE LIFTING FEEDER WELD BROKE LOOSE ANGLE FELL STRIKING EE IN FOREHEAD JUST UNDER HARD HAT 11/2IN CUT 8 STITCHES

STRIKING LOADER TOOTH VICTIM WAS REMOVING LOADER TOOTH WHEN CHIP OF METAL FLEW & STRUCK HIM IN STOMACH AREA. MEDICAL ATTENTION DID NOT SEEM NECESSARY AT TIME. PIECE OF METAL WAS FOUND TO STILL BE IMBEDDEED LATER & HAD TO BE REMOVED BY DR.

FALL TO SAME LEVEL. EMPLOYEE WAS INSTALLING A MUD FLAP ON AN R-50 WATER TRUCK WHEN THE FLAP FELL KNOCKING THE EMPLOYEE OFF BALANCE CAUSING HIM TO FALL ONTO THE CONCRETE APRON HITTING HIS ELBOW ON THE CONCRETE. THIS CREATED A FRACTURE ON THE LEFT RADIAL HEAD ELBOW.

EMPL WAS GUIDING DRIVE BELTS ONTO CRUSHER FLY WHEEL AS ANOTHER EMPL WAS ROTATING FLY WHEEL BY HAND. INJ ALLOWED LEFT RING FINGER TO INADVERTANTLY GET CAUGHT BETWEEN DRIVE BELT & FLY WHEEL RESU LTING IN MASHED & CUT FINGER.

EMPLOYEE WAS DRIVING DOWN A RAMP FROM A BENCH, THE ENGINGE QUIT RESULTING NO STEERING, EMPLOYEE JUMPED OUT WHILE TRUCK WENT THROUGH BERM AND TURNED OVER ON ITS SIDE OFF A 20 FT EMBANKMENT. EM PLOYEE SUFFERED CUTS AND BRUISES FROM CONTACT WITH GROUND AFTER JUMPING FROM TRUCK.

VICTIM WAS REMOVING MAIN BEARING CAP FROM A 8V71 DETROIT ENGINE WHEN IT SUDDENLY CAME LOOSE CAUSING THE VICTIM TO SCRAPER HIS FINGER ACROSS A BURRED EDGE OF THE ENGINE BLOCK - THIS PROCESS IS DONE BY HAND-THIS TOOK 7 STITCHES IN RIGHT INDEX FINGER.

AIR ARC ELDCTRODE FELL AGAINST LOADER ARM & FLASHED OFF CAUSING FLASH BURRS TO THE INDIVIDUALS EYES THIS WAS DONE WHILE INDIVIDUAL WAS SLAGGING OUT THE CRACK

THE 61 B DRAG BUCKET TAGLINE CABLE SLIPPED FROM HELPERS HAND:RAPID RETRACTION OF THE CABLE CAUSED A WHIPPING ACTION OF THE CABLE WHEN IT GOT CLOSE TO THE REEL.THIS WHIPPING MOTION IS WHAT STRU CK THE VICTIM ACROSS THE LEFT SIDE OF THE HEAD CAUSING SEVERE LACERATIONS TO THE HEAD AREA.THE VICTIM ALSO FELL FROM THE BOON.APPROX 8'TO THE GROUND.SKULL FRACTURE -LACERATION OF THE LEFT EAR

GLOVE STUCK BY WIRE CLOTH INTANGLING AND JERKED VICTIMS ARM CAUSING HIM TO LOOSE BALNCE AND FALL TO LOWER LEWVEL STRICKING AGAINST WIRE CLOTH WHICH CAUSED A PUNTURE WOUND TO THE NOSE OF VICTIM .

REMOVING 2'X 2' SECT OF METAL WHEN SHARP CORNER LACERATED LEFT INDEX FINGER ABOVE KNUCKLE.

EMPLOYEE SPRAYED STARTING FLUID ON A RAG AND SPILLED SOME ON HIMSELF. WHEN HE LIT A MATCH TO LIGHT THE TORCH HIS PANTS CAUGHT FIRE, BURNING HIS STOMACH NOTE EMPLOYEE WORKED THE FOLLOWING DAY AND HAS NOT RETURNED AT THIS TIME.

EMP WASIN PROCESS OF PATHCING A SCREEN ON THE TP ADECK AS HE CROSSED A SPRAY BAR HIS FOOT SLIPED AND STRUCK THE END OF THE EXPOSED 7/8" HOOK BOLT

EMPLOYEE WAS PULLING BINS WITH 35 EUC. HE STRUCK A STRUCTURAL BEAM OF PLANT SIDE. HE WALKED OUT ON THE DECK AND ATTEMPTED TO REPAIR DAMAGE WITH A HAMMER, HE TURNED AROUND AND EITHER STEPPED BACK AND/OR SLIPPED AND FELL OFF THE TRUCK, SIX FEET TO THE GROUND.

EMPLOYEE WAS HELPING TO DISASSEMBLE A FRONTEND LOADER FOR TRANSPORTATION. THIS REQUIRED BLOCKING THE MACHINE WITH CROSSTIES FOR SUPPORT AND PARTIAL DISASSEMBLY (REMOVAL OF SOCKET AND TIRES). B ACK WAS ALLEGEDLY STRAINED DURING THE AFTERNOON'S ACTIVITIES TO ACCOMPLISH THE TASK.

EMP WAS INSTALL3NG A FLIGHT BASE ON THE REWASH SCREW CONVEYOR WITH 2 OTHER WORKWERS IN AN EFFORT TO POSITION AND PLACE THE BASE IN A CONFINED AREA, HE TWISTED AND STRAINED THE R PECTORAL MUSC LE 3

LOADER BEING US9D TO PULL BY CHAIN A HOPPER CAR WHICH HAD DERAILED,BACK ONTO TRACKS.OPERATOR CLIMBED DOWN TO GROUND TO OBSERVE PROGRESS.WALKED AROUND LOADER OUT OF VIEW TO BOARD LOADER.RIGHT KNEE DISLOCATE8 FOR NO APPARENT REASON AND HE FELL TO GROUND AND CALLED FOR HELP.

WAS CLIMBING DO4N OFF FRONT END LOADER AFTER GREASING TOP ARMS & MISSED BOTTOM RING ON LOADER LADDER WHICH THREW HIM OFF BALANCEHE STUCK OUT HIS ARM TO CATCH HIMSELF & JAMED IT AGAINST THE LO ADER THUS SLIGH7LY CRACKING HIS RT FOREARM

FOOT SLIPPED TO3ONE SIDE WHILE WALKING ON SHOVELCATWALK.ABSENT FOLLOWING DAY TO GO TO DR.FOLLOWING MONDAY HE CALLED AND SAID HE COULDNT COME TO WORK BECAUSE OF POSSIBLE ULCERS CAUSING SEVERE S TOMACH PAINS WH3CH PROBABLY CAUSED HIS BACK TO HURT.WE DECIDED TO GIVE HIM BENEFIT OF DOUBT.

I.NAME WAS HELP3NG TO BREAK A BEARING HOUSING ON 5X14FT SCREENS & HOUSING WHICH WEIGHT 50LBS DROPPED ON I.NAME FOOT I.NAME WENT TO DOC & WAS TREATED FOR A SPRAIN RELEASED & RET URNED TO WORK THE NEXT DAY I.3AME LATER (SEVERAL WEEKS) REINJUSREDS ANKLE BADLY AT HOME-ACCORDING TO I.NAME BROTHER & WAS ABSENT FOR WEEKS WE FINALLY AGREED TO ALLOW I.NAME TO FILE ON AN INS GIVING I.NAME T

EMPL CLEANING O6T CHUTE ON PLANT.DIRT GOT INTO EYE WHICH HE WASHED OUT.HOWEVER,EYE BECAME INFECTED AND SWOLLED NEXT DAY SO SENT TO DR.

EMPL HOLDING NU7 WITH WRENCH WHEN HE LET WRENCH SLIP AND HANDLE STRUCK HIM IN JAW.NUT EMPL WAS HOLDING WAS ON LEAF-SPRING SUPPORT ON R-35 EUC TRUCK.

EMPL PULLING OU7 BOOM CABLE ON DRAGLINE AND HIS BACK GOT SORE.NO ACCIDENT DESCRIBED.

VICTIM WAS REMO5ING A FINGAL DRIVE ROCK RING ON EUCLID TRUCK WHEEL HUB WHEN HE JAMMED HIS LEG AGAINST STUDS STICKING OUT FROM HUB

VICTIM HAS AN U5CER ON HIS FOOT THAT WAS STIMULATED BY HIS DIABETIC CONDITION. VICTIM SAID HE MIGHT HAVE BUMPED HIS HEEL WHILE OPERATING THE DOZER WHICH COULD HAVE INTIATED THE SITUATION.

EE WAS STEPPING DOWN OFF THE D RAGLINE SERVICE TRUCK & DISLOCATED HIS RT KNEE AS HIS FOOT TOUCHED THE GROUND NO ACCD OCCURREED

I.NAME WAS MARKING HOLES ON A MOTOR TO DRILL FOR MOUNTING ON ELECTRICAL BOX HE WAS IN A KNEELING POSITION & FELL A BACK PAIN AS HE WAS STRAIGHTENING UP INTO THE STANDING POSITION

EMPL STEPPED DOWN OFF EUC AT END OF SHIFT SPRAINED HIS ANKLE.

JERKED HEAD TO SIDE TO AVOID GETTIN DIRT IN FACE WHILE LOOSENING BOLT NUT ON BRAKE LIGHT OF EUCLID.LATER FELT PAIN IN LOWER BACK.