Ivanhoe Concentrator: 1 muerte registrada Metal/Non-Metal

Night security guard noticed lightning, then at 4:11 noticed the flames. Lightning had struck a power pole next to the reclamation offices near tailings area. The pole was burned beyond use. No damage to the building and no personnel were working in the offices at the time. The fire was extinguished at 4:45.

The employee was starting to walk down an incline into the Sag #1 feed tunnel; he slipped on some mud and fell on his back and right shoulder. He was in pain and taken to the emergency room where he was diagnosed with a dislocated shoulder, and taken off work. ONGOING

A 998H loader was being used to load 740 haul truck. When rolling the bucket out of the bed, a bucket tooth hung on the bed causing employee to move around in the cab.

Employee was working under walkway and looked up, dirt from the walkway above fell and got into employee's right eye. He repeatedly flushed his eye, was examined by an EMT then taken to the clinic and was given a prescription, and returned to work.

The employee was exiting a transportation van at the tailings dam pond 4 location. It was still dark and ground area was level. Upon exit, the employee fell to the ground. The employee had pain in her right lower leg.

Personal Illness. Employee was surveying when he became dizzy and he sat down on the berm. The employee was observed by a co-worker who went to the employee to check on him and he immediately called the supervisor to come to the area where the employee was located. A First Responder was contacted and a Mayday was called. The employee was transported to the area hospital.

Employee was ascending a boarding ladder on a CAT 777 haul truck. When the employee lost his grip, he slipped allowing his body to twist. The employee supported his weight with his right side to prevent from falling to the ground.

An employee was climbing up a boarding ladder, and the employee lost his grip causing the employee to fall to the ground.

Operator driving the 621 water wagon hit a bump in the road sand seat bottomed out causing lower back pain. The seat was not set in proper position allowing full shock absorbing capability.

Employee was bending over closing the drain on the vacuum system in the X-Ray sampling room and when he tried to stand back up, the employee said that he felt pain in his lower back and could not stand up straight.

While placing a steel plate in place as a barrier, the bolt was placed in wrong and the plate slipped and hit the employee on the left foot, fracturing his metatarsal.

Employee was operating a D9 dozer and throttling forward pushing a load. His left hand was on the throttle control and he drove over a small drop off on the ground, jamming his left wrist against the throttle control. He was taken to the clinic, and referred to a specialist for evaluation to determine if he has a tear or hairline fracture in his wrist. Ongoing.

The flotation crew was in the process of installing liners on the spare vertimill screw with the screw suspended 4-6 inches above the ground. The brakes on the crane failed, causing the screw to sway pushing the employee against a crossmember in the stand. He sustained a scrape and contusions on his right shoulder and chest area.

Employee was directing a skid steer operator in lifting a metal saw horse when the saw horse slid off the bucket. The sawhorse landed above the safety toe of his left foot causing a deep contusion.

Employee was washing on the feeder floor at the primary crusher. He turned around to wash a different spot and felt his ankle give and rolled it. He was taken to the doctor, diagnosed with strain, and given restricted duty until 08/15/08. (Same ankle employee injured in 2007)

Employee was mopping the ladies restroom when the end of the fiberglass mop handle poked the employee in the right eye. Employee was working at a faster pace due to not completing assigned areas from the day before.

Employee waw taking antifeeze over to the dozer area. While standing near the dozer station area, he took a step to the right and rolled his right ankle. He was taken in to be checked and taken off work for approx. 4 wks. Currently ONGOING.

Employee was checking vertimill cyclone apexes in underflow tub and got stuck in mud, strained right leg and knee while attempting to free himself.

Employee was struck on the rt side of his face by a wrench on 4/9 while trying to remove a coupling using portapowers, but did not go to the doctor due to lack of visible injury or pain. On 4/18, his wife noticed his eye was not dilating. He was taken to the clinic, diagnosed with inflammation and swelling of the eye ball, given drops, and returned to work.

Employee was in front of the #3 Ball Mill basement floor float trunnion. As he went to leave he slipped on oil on the floor, fell and hurt his left shoulder. He was taken to the ER and taken off work until he can be evaluated by his personal physician on 2/25/08. ONGOING.

Climbing onto boom truck, he felt a sharp pain in right hamstring. Refused medical care until 2/8/08. Was given restricted duty on 2/12/08.

While walking from the thickner, employee slipped on some mud, stumbled but did not fall to the ground and strained his back. He was taken to the ER and taken off and released to his next regular shift, 8/13/07. He reported to work, but complained of pain, was told to see his personal physician, and taken off work until 8/21/07. ONGOING.

Employee was walking upstairs to report to work, carrying his coveralls under one arm, a 32 oz soda in one hand and 2 burritos in the other. As he reached the top of the stairs, with one foot on the step and the other on the landing, he tripped and hit his kneecap, chipping it. Currently ONGOING.

Employee was changing polidecks on #1 sag mill screen bottom deck. Debris entered both eyes when another employee removed a panel causing the debris to fall. When she reported to work the following day, she complained of pain in right eye. Was taken to an OD, and given an antibiotic.

Employee was walking back from the lunch room when he stepped in a puddle of water. The road had just been washed, and water had collected in a pot hole. He stepped on the edge of the pot hole, causing him to fall and twist his ankle. He was taken the ER, taken off work for 5 days, and referred to an orthopedic physician to verify any chips or fractures.

Employee was a passenger in a Kowasaki Mule going down a 5% slope ramp near the moly plant. The ramp was wet with a mud build up at the bottom. When employee hit the brakes, the mule slid into a column, causing the passenger to his his knee on the dashboard. He was taken to the clinic and knee brace was applied.

Employee was walking to the main gate to get a key when he tripped on a step and fell to the ground. He hit and broke his left knee cap on the concrete slab.

Employee was shoveling material off the stacker when he felt a pain on the right side of his back below the shoulder blade. He was treated with an ice pack and ibuprofen and didn't want to see a physician. On 06/06/07, employee requested to see a physician, and was taken off work until 6/11/07.

EE was changing out idler in the concentrator division. While using a pry bar to lift the idler to remove washers from under idler, pry bar slipped; the idler struck his finger resulting in injury.

Employee was driving a forklift down the hill on N side of Met lab & either hit the brakes or reverse pedal at the top of the hill, lost control, and started up the bank to the left. Forklift laid over on its side. Employee sustained a lacerated elbow, which required sutures, road rash on back of shoulders and a fractured nose. He claimed the engine stalled.

Employee was assisting on removing a broken inner liner on Sag #2 when a grinding ball blew up and a piece of the ball hit the employee on the lower jaw, causing a laceration which required two sutures to close.

Employee was going into the supervisor's change room, slipped, fell and hit her head and shoulder on a notice box mounted on the the outside wall. This jarred her neck. She was taken to the dr, diagnosed with a strain, then went the ER and taken off work until 4/13. Currently ongoing.

Employee was stepping over a 10" drisco pipe, right foot was over the pipe, foot gave way in sand. When employee tried to catch himself, his left foot stuck and he heard a pop in his left ankle and felt pain. He was taken to the ER, diagnosis pending MRI, taken off work. Currently Ongoing.

Employee was working in ball mill while other employees were using a jack hammer to remove a bolt. When they hit the bolt, feed fell between his safety glasses and eye. He flushed his eyes, but by Wednesday, 2-21, his eye was irritated. He was taken to the doctor, a small speck of metal was removed (not embedded), given antibiotics and returned to work.

Employee was walking from the employee parking lot to the truck shop on the access road when he slipped on pea gravel, causing his feet to come out from under him. He landed on his back and head, causing severe pain to his lower back. He was taken to the ER and taken off work through 01/16/07.

While installing new launders beween the 3 & 4 flotation rows, a hydraulic ram and spacer were being used to expand sections into place. The spacer kicked out from the jack and struck the employee on the right eyebrow, close to the nose, required 3 sutures to close.

While lifting a heavily loaded garbage can, the EE's right shoulder popped resulting in extreme pain for the EE. He was diagnosed with a strained joint and taken off work until his next work rotation, missing his next shift, pm of 8/24. He reported to work on his next rotation, 8/27 and hurt too much to continue working and went home, called requesting to see a DR. ONGOING.

Employee stepped into a hole in the concrete outside the smelter scale house and tripped hitting his chin on the ground and cutting his lower lip with his teeth. He received 3 stitches and was given prescriptions and released to work.

A concentrator employee was walking up the stairs, hit his toe on the first step and twisted his foot sideways. He had some swelling and pain but did not go the doctor. Later that evening the pain and swelling became more intense. He went to the clinic, had x-rays taken. Nothing broken but he does have a sprained ankle and will be on crutches and out at least a week.

Employee was using a hammer to help open a sump gate on Sag 2 sump when he felt a pop in his lower back above his left hip. He continued to work but later after using the skid loader, he felt tingling in his toes. He was taken to the dr. given a prescription and taken off work. Currently on going.

Employee was assisting another employee pulling wire from one level to the next. As the employee above was pulling the wire up, it wrapped around a piece of conduit on the floor, lifting it up and striking the employee between his glasses and hardhat, on the eyebrow, causing a cut which required four stitches to close.

EE was in process of checking flotation for possible start up later in shift. She was walking through area with about 6" of mud. Her feet got stuck in mud, she was trying to move & fell down to her knees. She put out her hands to brake her fall. She had swelling in left wrist so was taken to hospital. Later her knees, rt foot & head started hurting. Given release for 8/11.

While rebuilding a clean-up pump in the shop, the shaft fell off blocking smashing the tip of employee's ring finger. Employee continued working that day, reported to work the next day, but on the third day took himself to the Dr. and was diagnosed with a fractured finger tip. He reported to work with no restrictions.

EMPLOYEE WAS IN A KNEELING POSITION CALIBRATING A MARCY SCALE AT A DISTRIBUTION BOX AND FOUND IT DIFFICULT TO STAND UP. HE WAS TAKEN TO HIS PHYSICIAN, DIAGNOSED WIT A PRE-EXISTING CONDITION, WHICH WAS AGGRAVATED ATTEMPTING TO STAND BACK UP, HE WAS TAKEN OFF WORK FOR 5 DAYS, THEN RELEASED WITH A SEVEN DAY, LESS THAN 10 LBS LIFTING RESTRICTION

SAG MILL MAINTENANCE. EE WAS EXTRACTING THE LIFTER BAR FROM THE WEAR PLATE & IT ROLLED OFF THE BOLT, FALLING AGAINST HIS LEG & CAUSING A DEEP CONTUSION. EE RTW NEXT NIGHT, WORKED SEVERAL HOURS BEFORE COMPLAINING OF PAIN & GOING HOME. HE CALLED OFF SHIFT 5/14 & SAW PERSONAL PHYSICIAN ON 5/16. RECOMMENDED STAY OFF LEG APPROX. 4 DAYS. AS OF 5/26 NOT RELEASED TO RTW.

EMPLOYEE WAS USING A CUTTING DISC ON A 4 1/2" GRINDER TO CUT THE END OFF THE STILL WELLS FROM THE MOLY PLANT. THE BLADE BOUND IN THE STEEL AND KICKED BACK AND STRUCK HIS LEFT WRIST

Fusion tech. was lifting end of 18" HDPE and complained of back strain.

EE WAS CONNECTING THE FLEX HOSE USING DOZER TO PICK UP THE HOSE WITH THE BLADE. DOZER OPERATOR LOWERED THE BLADE SLOWLY WHILE EE WAS TIGHTENING THE BOLTS ON THE PIPE FLANGE. BLADE CAME DOWN ON EE'S LEFT FOOT JUST ABOVE THE SAFETY TOE. EE STATED HE DID NOT REALIZE HIS FOOT WAS THAT CLOSE TO THE BLADE. TAKEN TO ER: DIAG. FRACTURED METATARSAL; SEES ORTH. SPECIALIST ON 1/31/05.

EE was working in the top end of the tower mill where he was required to crawl in & out of a small space for access to the work, unaware of anything his eye until he was home. He reported his eye was hurting. they flushed it at the shop, where they found small piece of metal, some rust & a slight infection & given four rx and return to work. no time loss

EMPLOYEE WAS ON LOCOMOTIVE WHICH WAS PULLING CONCENTRATE CARS. THE AIR BRAKE SYSTEM FAILED RESULTING IN DERAILMENT. THE EMPLOYEE JUMPED FROM THE TRAIN, INJURING HIS RIGHT KNEE, RIGHT HAND AND LEFT SHOULDER. HE WAS TAKEN TO THE DOCTOR AND DIAGNOSED WITH KNEE STRAIN. HE IS TO USE A KNEE BRACE AND CRUTCHES FOR A WEEK, THEN TRY A WEEK WITHOUT; FURTHER EVALUATION AFTER THE SECOND WEEK.

Employee was clearing dirt and rocks from around a pipe trench on uneven ground, Employee lost his balance and fell sideways, his foot was between pipe and dirt, his weight of body falling sideways caused a fracture to his right ankle.

EMPLOYEE WAS HIT IN THE CHIN BY A PIECE OF STEEL THAT SPLINTERED OFF A GRINDING BALL. LACERATION REQUIRED 10 STITCHES. PLANT WAS DOWN, EE'S WERE ON TOUR. BALLS BECOME HOT & WHILE COOLING SOMETIMES HAVE PIECES SPLINTER OFF.

THE EMPLOYEE WAS STANDING IN FRONT OF THE LOADER BUCKET TOOTH, WHILE ANOTHER EMPLOYEE USED A 41 LB HAMMER TO HIT THE BACK OF THE TOOTH, WHEN A PIECE OF METAL BROKE OFF, STRIKING THE EMPLOYEE ON THE HAND.

EMPLOYEE WAS INSTALLING HOODS ON LIGHT FIXTURES IN FLOATATION AREA. EMPLOYEE IS SENSITIVE TO CONCENTRATION.

LEAVING WORK PLATFORM UNDER GMT, PLACED HAND ON THE CATCH OF A SAFETY BAR. SAFETY BAR DROPPED AND LANDED ON RIGHT MIDDLE FINGER.

LIFTING STEEL FLIGHTS FOR FEEDER. PLACED HANDS ON LOAD TO GUIDE IT, CAUSING A PINCH POINT.

EMPLOYEE DROPPED TRICON ON HIS LEFT FOOT, WHEN IT SLIPPED OUT OF HIS HANDS.

OPERATING DOZER ON STOCK PILE, EMPLOYEE THOUGHT HE FELT THE DOZER SHIFT AND JUMPED FROM DOZER.

AS EE CRAWLED OUT OF THE MOLY CELLS, HE LOOKED UP TO GET OUT AND A PIECE OF GRATING USED TO BLOCK THE LADDER SWUNG AND THE CORNER HIT HIM ON THE LIP.

EE INJURED LEFT ANKLE WHILE DISMOUNTING BULLDOZER AFTER DISCUSSING WORK SCOPE WITH EQUIPMENT OPERATOR.

EMPLOYEE WAS STANDING OUTSIDE LUNCH ROOM PULLINGOFF COVERALLS AND STRAINED HIS BACK.

WORKING ON SAG 2 DISCHARGE END TAKING OUT BOLTS WITH 90 POUND JACKHAMMER AND WAS HOLDING A TOOL AND PULLING AT THE JACKHAMMER WHEN IT SLIPPED AND PULLED THE EMPLOYEE'S ARM BACK. DID NOT SEEK M EDICAL ATTENTION UNTIL OCTOBER 5, 1999.

WHILE REMOVING THE #1 BALL MILL LINER & LOADING LINER ON LINER CART EE PINCHED LEFT MIDDLE FINGER

WHILE REPLACING A LINER,USING A DOUBLEJACK HAMMER THE EE STRUCK THE LINER & A SLIVER OF METAL STRUCK HIS KNEE

EE STATES HE WAS TIGHTENING BOLTS ON CRANE POD AND FELT PAIN IN THE RIGHT WRIST; ON 7/17/99 EE REPORTED CON'T DISCOMFORT IN RIGHT WRIST

EE WAS TAKING A HYDRUALIC HOSE OFF (CYLINDER) ON THE #4 BALL MILL, LIGHTLY TAPPING WITH A HAMMER. WHEN IT RELEASE, IT HIT HER ON THE LOWER LEFT JAW.

THE EMPLOYEE WAS TAKING THE DISCHARGE LINE APART ON A SAMPLE PUMP AFTER IT HAD CHOKED. THE DISCHARGE LINE DISCONNECTED AND THE SLURRY SPRAYED HIM IN THE FACE.

EE HAD BEEN MOVING ANGLE PIPE AND FELT BURNING SENSATION ON RIGHT ABDOMEN AREA. THAT EVENING HE NOTICED A BULGE IN THE SAME AREA. IT DIDN'T HURT, BUT BEGAN TO GROW AFTER A FEW DAYS.

EE WAS CLEANING OFF THE SCREEN IN THE LIME AREA.SOME LIME SPLASHED ON HIS FACE AND IN HIS LEFT EYE

THE EMPLOYEE WS WALKING INTO WORK. HE STOPPED TO WAIT FOR ANOTHER EMPLOYEE AT THE PARKING LOT,ANDWHNE HE TURNED HE TRIPPED ON A 1/2" SLAB OF ROUGHT CEMENT PAD AND FELL,LANDING ON HIS ELBOW.

EE WAS ALLIGNING A DISCHARGE LINE ON 33PP24, WHILE PULLING ON THE LINE, THE EE SLIPPED OFF THE PUMP SUPPORT & TWISTED HIS BACK. PRESCRIPTION WAS ISSUED.

WHILE PUTTING BEAM ON FEEDER BELT THE BEAM SLIPPED OFF AND CAUGHT RIGHT MIDDLE FINGER WHICH WAS LACERATED ADN REQUIRED 2 SUTURES. X-RAY REVEALEDSMALL FRACTURE ON DISTAL END OF FINGER.

WHILE USING 1/2" IMPACT, EMPLOYEE ALLEGES HIS IGHT WRIST STARTED TO HURT. REQUESTED TREATMENT 5-11-98, CAUSATION INVESTIGATION ONGOING.

THE EMPLOYEE WAS ATTEMPTING TO PRY OPEN AN AIR VALVE. THE PRY BAR SLIPPED AND LACERATED THE RIGHT RING FINGERTIP WHICH REQUIRED THREE SUTURES.

REPLACING A TRAMP CYLINDER ON DRY CRUSHER, SAFETY BLOCK POPPED & STRUCK EE'S HARD HAT, WAS PUSHED DOWN TOWARDS HIS RIGHT SIDE OF HIS FACE & LACERATED THE CHECK.

EMP WAS BACKING UP A WHEELED LADDER AND STEPPED ON A DECK INSPECTION DOOR THAT GAVE WAY. CAUGHT HIMSELF AS ONE LEG WENT INTO THE OPENING. EMP EXPERIENCED BACK PAIN BUT CONTINUED TO WORK THROUG H 9-28-96. EMP BEGAN LOSING TIME ON 9-29-96 WHENHE DID NOT COME BACK TO WORK.

EMPS LEFT LITTLE FINGER WAS FRACTURED WHEN CAUGHT IN A PINCH POINT BETWEEN AN I BEAM AND A CHUTETHAT WAS BEING PUT INTO PLACE.

FINGER WAS CUT WHEN IT WAS CAUGHT IN A PINCH POINT BETWEEN A MOTOR BASE AND A MOUNTING BOLT.

EE WAS USING A PRYBAR TO OPEN A VALVE AND PINCHED LITTLE FINGER CAUSING A SMALL EVULSION.

EMPLOYEE WAS LOADING A DUMP TRUCK WITH A BACKHOE WHEN HE LOST CONSCIOUSNESS.

A PIECE OF METAL FELL ON EMPLOYEES ARM WHILE HE WAS LINING A BALL MILL SPOUT A LACERATION REQUIRING SUTURES RESULTED

EE WAS SETTING BRAKES ON RAIL CAR, WHEN THEY COUPLED HE FELL BETWEEN THE COUPLE AND PLATFORM SMASHING FOOT, THEN CARS BACKLASHED RELEASING FOOT AND EE FELL TO THE GROUND. TORN LIGAMENTS IN ANK LE.

EMPLOYEE WAS WASHING DOWN THE FLOOR OF THE MILL BUILDING WHEN SOME CONCENTRATE SPLASHED INTO HIS EYE

WHILE USING A CHIPPING HAMMER, A METAL SLIVER 1/8" LONG PENETRATED HIS LEFT GLOVED THUMB. THE SLIVER WAS REMOVED AND THE WOUND WAS SUTURED.

WHEN CUTTING TAPE OFF WELDING LEAD, KNIFE SLIPPED & CUT HAND; REQUIRED SIX [6] STITCHES; WENT BACK ATO WORK AT 10:30 AM; NO LOST TIME. [NOTE] THIS WAS AT THE SMELTER PER CALL TO MR. REED

STANDING ON A PLATFORM OVER BASIN LAUNDER UNHOOKING A GATE CHAIN WHEN THE PLATFORM SLIPPED OFF THE WOODEN SUPPORT, CAUSING EE TO FALL AND HIT HIS LEFT KNEE ON THE CEMENT WALL. RESULT INDICATED BONE CYST NOT RELATED TO THE ACCIDENT AND POSSIBLE SMALL TEAR OF THE CARTILAGE.

I.NAME CAUGHT LEFT RING FINGER BETWEEN 4" OPENING AND A SLEDGE HAMMER HANDLE WHILE HAMMER WAS BEING USED IN A FLOAT CELL.

HE WAS HELPING ANOTHER EMPLOYEE LOCATE A HEATER SWITCH ON THE #6 CRANE WHEN HE STEPPED INTO A MOTOR HOLE.

I NAME WAS REMOVING A CLEVIS BOLT OFF A VALVE USING A BALL PIN HAMMER WHEN HE STRUCK HIS LEFT THUMB

EMPLOYEE SLIPPED ON A FORM AND TWISTED KNEE.

HE WAS INSTALLING A CONVEYOR PULLEY GUARD WHEN IT SLIPPED AND PINCHED HIS RIGHT INDEX FINGER BETWEEN THE GUARD AND A SUPPORT BEAM.

FIRE DAMAGE TO CONV BELTING CONV TABLE ELECT CABLING AND TRAYS HEAD TAKE UP, ON INJ DURING FIRE FIGHTING

INJURED WAS HELPING TO LOAD A JACK HAMMER IN A BOBCAT BUCKET WHEN HIS LEFT HAND FINGERS WERE CAUGHT BETWEEN THE HAMMER AND THE BUCKET.

INJURED ALLEGES THAT WHILE CARRYING A BOBCAT TIRE IN THE MOLY PLANT,HE SLIPPED ON AN OIL SPILL AND FELL ON HIS UPPER RIGHT HIP.HE REFUSED MEDICAL ATTENTION ON THE DAY OF THE ALLEGED ACCIDENT.H E STARTED VACATION ON 05-26-90.INJURED RETURNED FROM VACATION ON 06-10-90 WHEN HE ASKED TO SEE A DOCTOR.HE WAS GIVEN ADVIL AND RETURNED TO WORK.HE CONTINUED TO WORK UNTIL 10-30-90 WHEN HE PRO

I.NAME USING POCKET KNIFE TO CUT PIECE OF RUBBER LINING,CUT LEFT INDEX FINGER REQ 4 SUTURES.

I.NAME PICKING UP THICKTIONARY CUTTER IT SLIPPED FROM HER HANDS AND CAUGHT LEFT INDEX FINGER BETWEEN TABLE AND CUTTER.

EMPL WAS HLEPING TO LIFT VULCANIZER WHEN HE FELT PAIN IN LOWER BACK.

HE WAS HIT ON THE UPPER RIGHT LIP BY A PIECE OF METAL WHICH CAME OFF A PRIMARY CRUSHER LINER THAT WAS BEING WEDGED OUT BY A ROCK BREAKER.

I.NAME STRIKING A BEARING WITH HAMMER TO REMOVE IT OFF SHAFT WHEN PIECE OF BEARING BROKE OFF AND STRUCK I.NAME ON RIGHT KNEE.

HE WAS DISMOUNTING A DOZER FROM THE TRACK WHEN HE SLIPPED AND THIS CAUSED HIS LEFT KNEE TO HIT THE CORNER OF THE TRACK.

I.NAME OVERSTRETCHED RIGHT SHOULDER ,PUMP HE WAS PUSHING CAME OFF PULL LIFT.

WALKING UP SET OF STAIRS L KNEE GAVE OUT ON HIM HAS PRE EXISTING CONDITION HAS UNDERGONE SURGERY ON KNEE. DID NOT SEEK MED ATTENTION TILL 12-08-89

I.NAME WAS WALKING WHEN HE SLIPPED ON AN OIL SPILL CAUSING HIM TO LOSE HIS BALANCE AND FEEL A PAIN IN HIS LOWER BACK. I.NAME DIDN'T FALL.

I.NAME ANOTHER EMPLOYEE WERE LOADING EMPTY 55 GALLON DRUMS ON THE BACK OF A PICKUP TRUCK WHEN I.NAME FELT A MUSCLE PULL ON HIS ELBOW.

HE WAS BACKING A CHERRY PICKER FROM A RESERVIOR WHEN THE ENGINE DIED CAUSING HIM TO LOSE CONTROL AND HIT A BANK WITH THE REAR TIRES. THE CHERRY PICKER TRUNED ON ITS SIDE BUT HE REMOINED IN TH E CAB.

I.NAME WAS WASHING DOWN A CONE IN THE P-PLANT WITH A WATER HOSE WHEN A CLUMP OF CONCENTRATE AND DEBRI CAME LOOSE ON THE BOTTOM OF THE CONE AND SPLASHED ON HIS FACE AND EYES.

I NAME WAS CARRYING A ROLLED FIRE HOSE & A PIPE WRENCH DOWN A STAIRWAY WHEN HE CAUGHT HIS FOOT ON A TOE BOARD CAUSING HIM TO FALL

WALKING BY NO 1 AND NO 2 TUNNELS ON RAMP SLIPPED ON MUD REACHED TO CATCH ON RAILING FELT PAIN R SHOULDER

HE WAS INSTALLING A PRIMARY FUSE ON A HIGH LINE AT THE SOUTHSIDE BOOSTER STATION WHEN HE EXPERIENCED A MILD PAIN IN HIS GROIN.

I.NAME WAS HELPING ANOTHER EMPLOYEE PUT A SPLASH GUARD ON THE SOUTH CYCLONE UNDERFLOW BOX WHEN THE SPLASH GUARD SLIPPED FROM I.NAME'S HANDS AND CAME DOWN ON HIS LEFT HAND. EMPLOYEE WAS RE-EXAM INED ON THIS DATE (MAY 19, 1989) AND FOUND TO HAVE A HAIRLINE FRACTURE OF THE 3RD METACARPAL, LEFT HAND.

I NAME WAS MOVING MOLY DRUMS WITH A DOLLY WHEN HE LOST CONTROL OF THE DOLLY AND DRUMS CAUSING THE DOLLY HANDLE TO HIT HIM ON UPPER R KNEE

I NAME WAS SUING A COME-A-ALONG TO RAISE A PUMP AS THE TENSION INCREASE IT CAUSED I NAME TO USE BOTH HANDS TO PULL ON THE HANDLE AND CAUSED HIS R SHOULDER TO HURT I NAME HAS HAD PREVIOUS PROBL EMS WITH HIS R SHOULDER

EMPL WAS LIFTING SPARE TIRE OUT OF BACK OF PICKUP & PULLED MUSCLE ON LEFT SIDE OF BACK UNDER LEFT SHOULDER BLADE.

EMPLOYEE WAS WORKING INSIDE 1 SAG MILL ON THE LINER HANDLER, WASHING INSIDE THE SAG MILL WITH A WATER HOSE, WHEN HE FELT SOMETHING HIT HIM ON TOP OF HIS SAFETY HAT APPARENTLY A STEEL GRINDING BALL ANOTHER EMPLOYEE SAW HIM START TO FALL DOWN AND CAUGHT HIM, THUS AVOIDING FURTHER INJURY.

EMPLOYEE WAS REMOVING THE RETAINING CLIPS ON SOME FLOOR GRATING AT THE COPPER MOLY THICKNER. EMPLOYEE WAS USING A PRY BAR TO BREAK THE TACKS ON THEM. THE FIRST TEN CAME OFF ALL RIGHT, BU THE LAST ONE POPPED OFF AT A HIGH SPEED, CLIPPING EMPLOYEES RIGHT EAR.

EMPLOYEE STATES THAT HE HURT HIS BACK DESCENDING A LADDER. HE WALKED TO THE ELECTRICAL SHOP AND SAT DOWN IN A CHAIR AND COUL NOT GET UP. HE STATED HE HAD A SHARP PAIN IN HIS BACK WHEN ATTEMP TING TO STAND.

MOVING FUEL TANK WITH CRANE USING 6IN STRAPS HOOK ON STRAPS PINCHED FINGERS BETWEEN HOOK & TANK THIS ACCIDENT WAS MISTAKENLY RECORDED UNDER OSHA & WAS FOUND DURING AN INTERNAL RECORDS AUDIT

EMPLOYEE WAS UNCHOKING A PUMP. TWO PLATE COVERS OVER THE DITCH HAD BEEN SEPARTED ABOUT FOUR INCHES FRO WORKING ON LINE. EMPLOYEE ACCIENT;Y STEPPED BETWEEN THE TWO COVERS AND FELL INTO THE LA UDER, INJURING HIS RIGHT LEG.

WHILE STRIPPING A CONVEYOR EMPL WAS PULLING HOOK KNIFE ALONG CABLE WHEN BLADE BROKE CAUSING KNIFE TO SLIP AND CUT LOWER R THIGH THIS INCIDENT IS AN OVERSIGHT FOUND DURING AN INTERNAL AUDIT CHE CK OF RECORDS

EMPLOYEE WAS WASHING THE TAILINGS PUMPHOUSE FLOOR WHEN HE SLIPPED AND FELL, HURTING LEFT ARM.

EMPLOYEE WAS WORKING AT #1 CYCLONE DUSTER,WALKED INTO A DOWNWARD PROTRUDING PIPE.WAS WEARING HIS FACE SHIELD UP,AND EXTRA INCH OR TWO CAUGHT ON THE PIPE.HIS HARD HAT WAS FLIPPED OVER AND HE FE L BACKWARDS ,LANDING ON THE GROUND.

EMPLOYEE WAS GETTING READY TO USE A WATER HOSE IN FLOTATION AREA WHEN HE NOTICED THAT ONE OF THE HOSE CLAMPS WAS LOOSE HE H IT THE CLAMP WITH A HAMMER TO TIGHTEN IT WHEN HE TURNED ON THE WATG R THE CLAMP BROKE APART & STRUCK HIS ARM

EMPL AND ANOTHER WERE PICKING UP WHEELBARROW TO DUMP FLOOR DRI INTO TRASH DUMPSTER OUT SIDE SHOP WHEN INJURED FELT PAIN IN LOWER BACK. WHEELBARROW & LOAD WEIGHTED APPROX 40#. CONTINUED TO W ORK UNTIL 11/30/88.

WAS CLOSING LEAKING VALVE USING CHEATER PIPE & VALVE STEM BROKE OFF CAUSING HIM TO STRAIN BACK.

EMPLOYEE WAS ASSISTING WITH A BALL MILL RELINING JOB LINERS WERE BEING MOVED INTO PLACE WITHA FORKLIFT WHICH HAD AN EXTENSION ON IT. EMPLOYEE GOT HIS HANDS BETWEEN THE EXTENSION AND BALL MILL LINER TO RE-RIG THE CABLES, AND THE FORKLIFT HUNG UP, THEN DROPPED AND CAUGHT HIS RIGHT HAND BETWEEN THE LINER AND THE LIFTING ARM.

EMPL FIRST INJURED KNEE 3/20/88 ON 11/6/88 HE WAS PUSHING 1/3 FULL BARREL OF GREASE INTO ELEVATOR WHEN HE SLIPPED & FELL ON RIGHT KNEE & REINJURED IT.

EMPLOYEE WAS LOOSENING BOLGTS ON A TGAILINGS PUMP WITH 11/2 IMPACT WRENCH WORKING WITH HANDS OVER HEAD WHEN BOLT CAME LOOSE WRENCH KICKED BACK EMPLOYEE WAS TRYING TO HOLD ON TO THE WRENCH & KEEP HIS BALANCE FELT PAIN IN STOMACH DIAGNOSED AT THAT TIMEA S UMBILLICAL STRAIN BECAME A LOST-TIME INCIDENT EFFECTIVE 110388 WHEN HE WAS RE-DIAGNOSED AS HAVING A HERNIA

EMPL ASSISTED IN CHANGING OUT TWO IDLERS ON COARSE ORE FEEDER BELT WHICH REQUIRED ALOT OF PULLING & PUSHING & ALLEGES HE EXPERIENCED LOWER BACK STRAIN WHILE DOING SO.

AT END OF SHIFT, HE WAS WALKING OUT OF APRON FEEDER TUNNEL AHEAD OF A BOBCAT BEING OPERATED BY ANOTHER EMPLOYEE. THE BOBCAT STALLED OUT AND BEGAN TO ROLL DOWN THE TUNNEL INCLINE, GAINING SPE ED AND HE WAS RUNNING IN FRONT OF IT. BOBCAT OPERATOR RAN IT AGAINST CONVEYOR STRUCTURE TO STOP IT. HE RAN TO THE BOTTOM OF THE TUNNEL AND SOMEHHOW TRIPPED AND FELL INTO THE CLEANUP PUMP SUMP,

EMPL WERE INSTALLING APUMP AT PRECIPITATION PLANT I NAME WAS HOLDING SOCKET WRENCH ON LOWER FLANGE BOLT WHILE OTHER EMPL TIGHTENED IT THE WRENCH SLIPPED AND CUT I NAME FIRST JOINT OF R LITTLE FINGER

EMPLOYEE WAS SWITCHING BOXCARS AT CATHODE LOADING DOCK USING SWITCHMASTER THE SWITCHMASTER COUPLED TO A LOADED BOXCAR GAINED EXCESSIVE SPEED AND EMPLOYEE WAS UNABLE TO STOP THE UNIT AFTER TR AVELING 1.2 MILES ON THE MAIN TRACK THE EMPLOYEE JUMPED FROM THE UNIT DUE TO THE HIGH SPEED OF TRAVEL HE WAS UNABLE TO MAINTIAN HIS BALANCE WHEN HE HIT THE GROUND TUMBLED FORWARD ONTO HIS FA

EMPLOYEE WAS CHECKING THE OVERFLOW CYCLONES ON THE BALL MILLS WHEN HE STRUCK HIS HEAD AGAINST AN I BEAM SUPPORT AND TWISTED HIS NECK

REMOVING THE DISCHARGE SPOOL ON A PUMP FOR REPAIRS USING A CRESCENT WRENCH TO PRY ON THE SPOOL TO REMOVE IT EMPLOYEE SLIPPED AND TWISTED HIS BACK

WALKING DOWN INCLINE AT #1 SAG TUNNEL SLIPPED AND INJURED HIS BAKC

WHILE CHANGING A POLY DECK PANEL ON SCREEN, TOP DECK, HOOKED RIGHT RING FINGER AND TWISTED IT.

EMP WA S EMPTYING REGRIND BUCKET HOLDING BUCKET HANDLE WITH LEFT HAND WHILE HITTING HANDLE WITH SLEDGEHAMMER USING RIGHT HAND. MISSED HANDLE AND STRUCK LEFT HAND WITH SLEDGEHAMMER

ATTEMPTING TO OPEN THE DOOR ON THE TOWER MILL WITH ANOTHER EMPOLOYEE HE WAS TIGHTENING ON PULL LIFT WHILE OTHER EMPLOYEE WAS HITTING THE DOOR WITH A HAMMER THE DOOR SWUNG OPEN WHILE I NAME HA D PRESSURE ON PULL LIFT PRESSURE ON PULL LIFT RELIEVED SUDDENLY CAUSING I NAME TO FALL OVER BACKWARD LANDING ON A PIPE ALIGNMENT CLAMP WHICH WAS ON THE FLOOR

EMPLOYEE STRAINED HER BACK WHILE PULLING HEAVY HOSE TO THE 30' THICKENER AT CONCENTRATOR

WENT TO CHECK SCREW CONVEYOR CHUTE. OPENED LID AND AIR, MOLYBDENITE AND STEAM BLEW OUT INTO HIS FACE

SLIPPED IN OIL, TWISTED RIGHT KNEE. EMPLOYEE ALLEGES THE INCIDENT HAPPENED 3-4 WEEKS PRIOR TO 5-26-88, EXACT DATE NOT AVAILABLE. DATE OF FIRST TREATMENT IS 5-26-88.

ASSIGNED TO REMOVE BROKEN IDLERS FROM THE ROADWAY ALONG THE RECIRC CRUSHER AREA I.NAME AND ANOTHER EMPLOYEE LIFTED A 54 IN RETURN GUIDE IDLER WHICH HAS A SWIVEL POINT IN THE MIDDLE THE SWIVEL PORTION OF THE IDLER TURNED PINCHING I.NAMES LEFT THUMB

EMPLOYEE WAS KNEELING DOWN TRYING TO REMOVE A PIECE OF GRATING.GRATING STILL HAD A SMALL AREA WELDED ON ONE OF THE RAILS,AND AS HE JERKED ON IT HE FELT AMUSCLE PULL IN RIGHT SIDE OF LOWER ABCK

THE INJURED WAS WORKING INSIDE #4 BALL MILL AS PART OF A 6-MEN CREW.THEY WERE USING A 1 1/2 TON PULL A FEED END LINER FROM THE CENTER OF THE MILL TO THE OUTER FEED END LINER AREA.THE LINER WAS DRAGGING OVER THE BALL LOAD,IT SUDDENLY MOVED FAST AND CAUSED THE PULL LIFT TO TURN.THE HANDLE OF THE PULL LIFT PINCHED HIS AHND BETWEEN THE HANDLE AND THE MILL SHELL.

EMPLOYEE WAS STRAIGHTENING OUT A HANDRAIL ON NO.3 BALL MILL CHUTE WITH 24" CRESCENT WRENCH.HE WAS PUSHING AWAY FROM HIMSELF WHEN HE FELT A PAIN IN HIS ABCK.

EMPLOYEE JUMPED OFF FROM PLATFORM OF HYDROLIFT TRUCK, A DISTANCE OF ABOUT 2 OR 2 1/2 FEET, TO THE GROUND, LANDED ON BOTH FEET AND FELT SHARP PAIN IN LOWER LEFT BACK.

AS EMPLOYEE WAS ENTERING COMPARTMENT ON NO. 5 CRANE HE SLIPPED ON OILY FLOOR AND TWISTED RIGHT LEG.

EMPL ASSIGNED T2 CONCENTRATOR TO ASSIST MAINTENANCE MECHANICS IN CHANGING THROAT FEED END LINERS ON #1 BALL MILL.WRESTLING LINER INTO PLACE AND STRAINED HIS BACK.

EMPL TURNING A 5ALVE USING A BAR GOT PAIN IN RIGHT HAND AND ARM.

EMPLOYEE WALKED3UP BEHIND ANOTHER EMPLOYEE WHO WAS CUTTING ELECTRODES WITH A CUTTING TORCH, TRIPPED AND LOST HIS BALANCE, AND EITH TOUCHED HOT CUTTIING TORCH OR LANDED WITH HIS HAND ACROSS THE FLAME. 3

WHILE USING HYD9AULIC JACK 12 TON, TO OPEN FEED BOX TO INSTALL LINER INSERT, THE JACK SLIPPED OFF AND HIT EMP ON UPPER LEFT THIGH

EMPLOYEE WAS LI0TING A COOPER MOLY PUMP OUT OF SUMP WHERE IT HAD FALLEN. HE DID NOT ASK FOR ASSISTANCE, BUT TRIED TO LIFT THE PUMP BY HIMSELF, AND PULLED SOMTHING IN HIS BACK. THIS WAS ORIGINA

EMP AND ANOTHER3EMPLOYEE WERE REMOVING A PUMP MOTOR FOR REPAIRS, HE WAS USING A PRY BAR TO MOVE PUMP. WHEN HE PULLED UP ONTHE BAR HE HURT HIS LOWER BACK

WHILE CUTTING M9TAL A PIECE OF SLAG WENT INTO LEFT EAR.

EMPL REACHING U1 FOR ROLL OF TOWELS WHICH WERE STORED INBOX ON HIGH SHELF IN STORAGE ROOM.BOX CAME DOWN ON TOP OF HIM AND HE PUSHED BOX BACK UP ON THE SHELF HE SPRAINED HIS BACK.

I NAME WAS ASSI8TING WITH RTHE REASSEMBLY OF #1 BALL MILL CLUTCH. WHILE TURNING THE CLUTCH WITH A NYLON SLING THE OVERHEAD CRANE THE SLING CAME LOOSE AT ONE END AND STRUCK I NAME IN THE NO NOSE. BLEEDING 7OULD NOT BE STOPPED SO EMP WAS TTRANSPORTED BY AMBULANCE TO LAS CRUCES HOSPITAL FOR FURTHER TREATMENT BY EENT SPECIALIST, DR PAI

EMP WAS WORKING3IN THE CRUSHER POCKET WHEN A BASEBLL SIZED ROCK FELL APPROX 15 FT, HITTING LEFT HAND ON BACK SIDE, RIGHT HAND AND RT LEG

EMPLOYEE WAS LO4ERING AN ENGINE SIDELINER FROM APUMP.AS IT WAS SET DOWN ON THE FLOOR THE INJURED WAS STANDING ON THE SOUTH SIDE,GUIDING IT WITH HIS LEFT HAND,WHEN IT SWUNG TO THE SOUTHWEST,PI NCHING HIS LEFT3THUMB BETWEEN SHACKLE OR CABLE AND THE SUCTION SIDELINER PUMPCASE.

EMPLOYEE WAS DO3NG ROUTINE WORK IN X-RAY ROOM, UNCHOKING X-RAY LINE.BENT OVER TO CHECK X-RAY WINDOW AND WHEN HE STRAIGHTENED UP HE FELT A SHARP PAIN IN THE SACROILIAC AREA.

WAS ASSIGNED TO3REPAIR #1 SAG (SEMI-AUTOGENOUS GRINDING) BALL MILL FEED BOX CARRIAGE JATOPS. WHILE ATTEMPTING TO FIT A PIECE OF CHANNEL PLATE HE DROPPED IT ON HIS LEFT FOREARM.THE PLATE WAS HO T WHERE HE HAD 6EEN CUTTING ON IT LAND IT BURNED HIS ARM.

EMPLOYEE WAS PA9T OF A 7-MAN CREW CHANGING SHELL LINERS AT #2 SAG MILL.HE WAS COMING OFF THE SAG MILL LINER HANDLER MACHINE AND STEPPED ON A 1 1/2 INCH WASH WATER HOSE, TWISTING HIS LEFT ANKL E. 3

EMPLOYEE WAS WA5KING TO REGRIND MILL CARRYING BUCKETS FOR OIL,SLIPPED ON SOME MUD ON THE FLOOR AND FELL BACKWARD,CATCHING HIMSELF ON HIS HANDS.

DURING CLEANUP 5T THE CONCENTRATOR MAINTENANCE SHOP A SEMI-AUTOGENOUS GRINDING MILL JACK SHIFTED AND THE HYDRAULIC HOSE FITTING STRUCK I NAME LEFT BIG TOE RESULTING IN A FRACTURE.

EMPLOYEE SLIPPE8 ON GRAVEL AND TWISTED LUMBAR REGION. (RX: MOTRIN;ROBAXIN)

EE ALLEGES HE W5S HELPING GRINDING OPERATOR CHANGE CYCLONES ON 5-25-87 WHEN A WRENCH SLIPPED AS HE WAS REMOVING SOME BOLTS & HE HIT HIS RT AH %@*%* HAND AGAINST A SUPPORT BEAM & HE HAS CON TINUED TO HAVE 8ORNESS IN HIS RT WRIST.

EMPLOYEE HAD JU8T FINISHED CLEANING AT THE CRUSHER AND WAS PULLING HIMSELF OFF THE CONVEYOR BELT WHEN HE MISSED HIS FOOTING AND CAUGHT HIS LEFT HAND BETWEEN TWO BEAMS,HANGING HIMSELF BY HIS LE FT HAND. ANOTHE9 EMPLOYEE WITNESSED THE ACCIDENT AND HELPED INJURED EMPLOYEE DISLODGE HIS HAND AND GET DOWN. (RX DARVON).

EMP WAS CLEANIN1 AN OIL RESERVOIR AT THE CONCERTRATOR WHEN THE LID SLIPPED AND FELL ON HIS LEFT HAND. 3RD & 4TH FINGERS

EMP WAS WORKING3AT SEVERAL JOBS AT THE CONCERTRATOR DURING THE DAY. HE GOT A PIECE OF FOREIGN MATERIAL INTO HIS R EYE, BUT WAS NOT SURE HOW OR WHAT TIME IT HAPPENED, ONLY THAT ABOUT 3:00 PM IT STARTED IRRITAT3NG HIS EYE SUFFICIENTLY TO WARRANT ATTENTION. HE WAS TRANSPORTED TO MEDICAL CLINCI FB REMOVED BUT STILL HAD RUST RING, SO WAS REFERRED TO OPTHLAMOLOGIST FOR FURTHER TREATMENT

EMPLOYEE WAS PA9T OF A CREW INSTALLING THE WEST SCREEN SPLASH CURTAIN. THE CURTAIN WAS SUSPENDED FROM THE OVERHEAD CRANE. AS THE CURTAIN WAS BEING PULLED INTO PLACE THE CURTAIN FRAME GOT CAUGH T UNDER THE UPR3GHT SUPPORT AND SNAPPED UP, STRIKING EMPLOYEE IN THE MOUTH AREA.

EMPLOYEE WAS OP9RATING A BOBCAT LOADER.WHEN HE PARKED THE LOADER, HE WAS UNABLE TO GET OFF THE LOADER BECAUSE OF BACK PAIN.

THE INJURED WAS3ASSISTING MAINTENANCE EMPLOYEES AT CRUSHER. HE WAS CUTTING SOME RUBBER SKIRTING TO INSTALL ON SIDEBOARDS WHEN THE POCKET KNIFE SLIPPED FROM THE RUBBER AND STRUCK HIS LEFT THIGH ,CAUSING A PUNC7URE WOUND.

EMPLOYEE WAS IN8TALLING A PLUNGER INTO A PUMP. HE BALANCED THE PLUNGER ON THE EDGE OF THE PUMP TO SPRAY THE PLUNGER WITH WD-40. THE PLUNGER SLIPPED OFF THE EDGE OF THE PUMP. EMPLOYEE GRABBED L XX PLUNGER TO K9EP IT FROM FALLING TO THE FLOOR, PULLED MUSCLE IN HIS LEFT SHOULDER.

WHILE BRINING A3PAIL OF CLEANING SOLVENT TO THE JOB SITE, EMPLOYEE STEPPED OFF FROM AN EMBANKMENT OR BERM APPROX. 2 1/2 FT HIGH AND TWISTED HIS RIGHT ANKLE.

EMPLOYEE WAS LO2SENING A JAMMED NUTON SOUTH TAILINGS THICKENER LIFTING MECHANISM ADJUSTING BOLT. THE NUT BROKE LOOSE, PINCHING EMPLOYEE'S RIGHT LITTLE FINGER BETWEEN THE WRENCH AND DRIVE CHAIN GUARD. 3

EMPLOYEE WAS OP9RATING A BULLDOZER TOWARD THE STOCKPILE SHE CAME TO A CONCRETE DROP OFF LOST CONTROL OF DOZER DOZER ROLLED OFF LANDING ON ITS RT SIDE

EMPLOYEE WAS CL9ANING SCREENS ON A TRANSFER PUMP DISTRIBUTING BOX WITH A WATER LANCE WHEN LIMEWATER WAS SPRAYED IN BOTH EYES EMPLOYEE WAS NOT USING SAFETY SHIELDS WHICH HAVE BEEN PROVIDED

WHILE LIFTING A3FEEDER OF APPROX. 100 POUNDS OR MORE, WITH HELP OF A FELLOW EMPLOYEE, HE FELT SHARP PAIN IN THE GROIN AREA.

FOUR EMPLOYEES 4ERE INSTALLING REVERSE SPRIAL IN DISCHARGE END OF BALL MILL. THERE WAS A LONG CABLE ON THE HOOK, A SHACKLE THAN A CABLE LOOPED THOUGH A HOLE IN THE SPIRAL EXTENSION WHICH WAS B EING INSTALLED.3 AS THE CRANE WAS RAISED THE CABLE SNAPPED. THE CABLE WITH THE SHAKLE SWUNG UP IN THE AIR ON THE WAY DOWN HIT HIM ON THE RING FINGER OF HIS LEFT HAND.

INSPECTING A SE4I-AUTAGENOUS GRINDING MILL & A 5" BALL OF STEEL & MUD CAME OFF THE ROOF &S TRUCK EE O LEFT SHOULDER.

MOVING SOME AIR3HOSE FROM #1 BALL MILL TO #3 BALL MILL. AS HE STARTED TO WALK AWAY WITH THE HOSE HE SLIPPED ON SOME MUD ON THE FLOOR AND FELL.

WAS WALKING AND3TRIPPED OVER PIECE OF PIPE,INJURED LEFT KNEE.

EMPLOYEE WAS RE4OVING A VICTAULIC COUPLING ON A PUMP FEED LINE FOR PUMP REMOVAL.WHEN HE REMOVED THE COUPLING,LIME GUSHED OUT,COMPLETELY SATURATING HIM.LIME GOT INTO HIS EYES.THE VALVES ISOLATI ING THE PUMP HA8 NOT BEEN CLOSED.

I NAME WAS PUTT3NG UP SHEETING THE PULLEY ON TOP CAME OFF HOOK I NAME WAS HOLDING ONTO THE ROPE,WHEN THE WEIGHT OF SHEET AND ROPE TWISTED WRIST.

WHILE LIFTING A3CHUTE, IT TWISTED AND CAME UP BETWEEN THELEGS, LACERATING THE RIGHT TESICLE. TWO STITCHES WERE TAKEN.

EMPLOYEE REPORT9D THAT HE HAD BEEN STRUCK BY A 90 LB JACKHAMMER ON LEFT LEG JUST BELOW KNEE WHEN HE AND A FELLOW EMPLOYEE WERE DRIVING IN LINER BOLTS APPROX 15 MIN LATER WHILE USING A DOUBLE J ACK THE HANDLE 8TRUCK SAG MILL SHELL CAUSING A JOLT TO BOTH WRISTS

EMPLOYEE REPORT9D THAT HE HAD BEEN STRUCK BY A 90 LB JACKHAMMER ONLEFT LEG JUST BELOW KNEE WHEN HE AND A FELLOW EMPLOYEE WERE DRIVING IN LINER BOLTS APPROX 15 MIN LATER WHILE USING A DOUBLE JA CK THE HANDLE S7RUCK SAG MILL SHELL CAUSING A JOLT TO BOTH WRISTS

EMPLOYEE WAS WO9KING INSIDE A BALL MILL WHEN A BELLY LINER FELL FROM THE SIDE OF THE MILL STRIKING EMPLOYEE ON SHIN

TWO EMPLOYEES W9RE LIFTING A BALL MILL LINER WITH A SPUD BAR ONE EMPLOYEE LET GO OF HIS BAR CAUSING I.NAMES BAR TO HIT HIM IN THE RIBS THE BLOW THREW HIM AGAINST THE WALL AND KNOCKED THE BREA TH OUT OF HIM E4PLOYEE DID NOT SEEK MEDICAL ATTENTION UNTIL 10-21-86

WHILE CUTTING B2LTS WITH CUTTING TORCH PIECE OF HOT METAL LANDED ON HIS GLOVE

EMPLOYEE WAS WO9KING INSIDE A BALL MILL WHEN SOME DIRT AND DUST FELL ON HIM HIS EYES STARTED HURTING SO HE WASHED THEM OUT WITH WATER WHILE ON HIS LUNCH BREAK HIS EYES CONTIN6ED TO BOTHER HIM AND ON 10-12-86 HE REPORTED THE CONDITION TO SECURITY AND WAS TRANSPORTED TO MEDICAL CENTER FOR TREATMENT EYE WAS CLEANED AND FOREIGN OBJECT REMOVED FROM CORNE

THREE EMPLOYEES3WERE CHANGING GRATES INSIDE A SEMI AUTOGENOUS GRINDING MILL WHEN A CHUNK OF MATERIAL WHICH WAS STUCK TO THE TOP OF THE MILL BROKE LOOSE SUDDENLY AND FELL HITTING I.NAME ON THE HEAD HE WAS TR5NSPORTED TO HOSPITAL AND ADMITTED OVERNIGHT FOR OBSERVATION