Buscar en el registro

EE STATES RODS FELL AND CAUGHT ROD CLAMPS, FOOT PEDAL RELEASE, CAUSING PEDAL TO GO BACK IN UPWARD POSITION WITH EXTREME FORCE.

EE STATED HE WAS GRINDING METAL, WHEN DEBRIS FLEW INTO HIS LT LOWER LEG CAUSING A LACERATION AND A CONTUSION.

WHILE OPERATING BLADE, EE DIRECTED HIS ATTENTIONAWAY FROM THE DIRECTION OF TRAVEL. DURING THIS BRIEF PERIOD OF TIME, THE EQUIPMENT STRUCK AN EMBANKMENT, JARRING HIM UNEXPECTEDLY, RESULTING IN A PULLED BACK MUSCLE.

EE WAS PACKING CEMENT WHEN BAG BLEW UP AND CEMENT GOT UNDERNEATH SAFTEY GLASSES INTO LEFT EYE. EE ALSO TURNED BACK WHEN GETTING UP AND HURT BACK. EMPLOYEE'S EYE IS OK BUT IS ON RESTRICTED DUT Y OF NO LIFTING FOR 4 WEEKS.

WHILE ATTEMPTING TO REPOSITION A PNEUMATIC BAG CHAIR EMPLOYEE BUMPED THE BAGGER START BUTTON & MADE THE BAG CHAIR CYCLE DOWN PINCHING & CUTTINGHIS RIGHT THUMB & FOREFINGER.

SEVERAL EES WERE GRINDING OVERHEAD IN A CONFINED SPACE. PARTICLES OF METAL WILL FALL FROM EQUIPMENT DURING THIS PROCESS. AS A RESULT, A PIECE OF THE METAL GOT UNDER THE WELDING HOOD AND BECAME EMBEDDED IN THE LEFT EYE.

WHILE EMPLOYEE WAS ATTEMPTING TO REPLACE A BAD BEARING, THE TRIGGER ON A 3/4" DRIVE AIR IMPACT WRENCH HUNG IN THE RUN POSITION, CAUSING HIS HAND TO BE CAUGHT AGAINST A PIECE OF UNISTRUT.

EMPLOYEE WAS KNOCKED OFF OF A LADDER WHEN A BEAM OVERHEAD STRUCK THE LADDER. THE BEAM WAS BEING REPOSITIONED.

HE WAS USING A GRINDER TO GRIND ON A PIECE OF PIPE. HE WEDGED THE GRINDER BETWEEN 2 PIECES OF PIPE, WHICH CAUSED THE GRINDING WHEEL TO KICK BACK & STRIKE HIS RIGHT KNEE.

ATTEMPTING TO CLEAR A SANDBLASTER LINE. HAD TURNED OFF AIR SUPPLY, BUT POD WAS STILL UNDER PRESSURE BECAUSE OF PLUGGED LINE. PRESSURIZED AIR AND GRAVEL BLEW OUT ONTO EE'S HAND.

EE WAS WEARING PANTS INSIDE BOOTS THEREFORE ALLOWING HOT METAL TO GET INSIDE BOOT.

EMPLOYEE WAS ASSISTING IN REMOVAL OF 8" BY 8" TUBULAR STEEL FROM NEW CLINKER COOLER. AS ANOTHER EMPLOYEE CUT TUBE STEEL LOOSE WITH TORCH, INJURED EMPLOYEE LOST HIS GRIP ON CUT PIECE (APPROX 18 " LONG) AND DROPPED IT ON HIS RIGHT FOOT, CAUSING A FRACTURE TO BIG TOE.

EE USING TEAR OUT MACHINE IN KILN WHEN A BRICK PRICHOCET OFF MACHINE AND STRUCK HIM ON THE RIGHT FOOT.

EE HAS BEEN BAGGING CEMENT AS HE EXITED PACKER, A SPROUT ON HIS BAGGING SYSTEM INADVERTENTLY ACTIVATED, CAUSING CEMENT TO DEFLECT INTO EE'S EYE. NOTE: HE WAS WEARING A FACE SHIELD AT THE TIME OF THE ACCIDENT

EMPLOYEE WAS USING AN OXYGEN LANCE TO CUT SIDE WALL OUT OF CLINKER COOLER. OXYGEN REGULATOR MALFUNCTIONED CAUSING LANCE TO BACK FLASH AT LANCE HANDLE. EE HAS A 2" 2ND DEGREE BURN TO LEFT WRIST AND A 1ST DEGREE BURN TO LEFT THIGH.

EMPLOYEE WAS GRINDING A PIECE OF STEEL ON A PEDASTAL GRINDER, STEEL GOT CAUGHT BETWEEN GRINDING WHEEL AND GUARD AND SLAMMED DOWN ON THE GRINDER REST, CATCHING EMPLOYEE'S LEFT INDEX FINGER BETW EEN STEEL AND GRINDER REST.

EE WAS GRINDING (WEARING FACE SHIELD & SAFETY GLASSES) FELT DUST IN HIS R EYE

EMPLOYEE HOLDING 4"X2"X3' PIECE OF INSTULATION WITH LEFT AHND WHILE DRILLING WITH RIGHT HAND. THE DRILL BIT CAUGHT PART OF HSI GLOVE AN DFRACTURED LEFT 5TH FINGER.

EE WAS ATTEMPTING TO REMOVE FOREIGN MATERIAL FROM A CEMENT PAKER. THE INJ EE GAVE INSTRUCTIONTO A FELLOW EE TO TURN THE IMPELLER BY HAND HIS HAND WAS TOO CLOSE TO THE IMPELLER & WAS CAU GHT BETWEEN THE IMPELLER & THE HOUSING

WHILE REMOVING ROCK FROM BEHIND THE DEFLECTOR SHIELD ON THE NORTH SIDE WHEEL IN THE JAW THE DEFLECTOR MOVED & CAUGHT ON HAND

HOT DUST WAS EXPELLED FROM PREHEATER, UNLATCHED PORT ABOVE ANALYZER PROBE. EMPLOYEE RECEIVED A BURN ON HIS FOREARM.

OUTRIGGER OF CRANE WAS PLACED ON VICTIM'S RIGHT FOOT. TENDON, LIGAMENT AND BONE DAMAGE.

EE WAS AIR-ARCING A BUCKET LINER CUT OFF THE 998B AFTER AIR-ARCING HE SWITCHED THE AIR HOSE TO A PNEUMATIC DHARGE AS SOON AS HE STARTED CHIPPING. THE AIR HOSE UNCOUPLED AND STRUCK EE ON THE SI DE OF HIS FACE.

WENT TO DUMP P-1 TROUGHING ROLLER END TAB CAUGHT SLEEVE ROLLER FELL ON MIDDLE FINGER AND FRACTURED.

WHILE BURNING A HOLE IN CONVEYOR FRAME A PIECE OF HOT SLAG BOUNCED UNDER GLASSES AND BURNED RIGHT EYE.

EE WAS WORKING ON THE SCREENS WITH HIS IMPACT GUN WHEN THE PIN THAT HOLDS SOCKETS CAME OUT & CUTHIS HAND

WHILE GRINDING ON BELL HOSUING A PIECE OF METAL FLEW OFF AND HIT HIM IN THE RIGHT EYE. THE EE ALLERGED HE WAS WEARING SAFETY GLASSES AT THE TIME BUT NOT A FACE SHIELD.

WHILE WELDING SPARK FLEW IN EAR.

THE LAYER PUSHER OF THE PALLETIZER BECAME JAMMED. EE THREW MAIN DISCONNECT ON MACHINE, BUT HE DIDN'T THROW IT FAR ENOUGH NOR DID HE DO A PROPER LOCKOUT AND TEST OF THE MACHINE. WHEN HE WENT TO RELEASE THE JAM, THE MACHINE WAS STILL ENERGIZED AND WHEN IT BECAME UNJAMMED, IT CAUGHT BOTH LEGS BETWEEN THE LAYER PUSHER AND FRAME OF THE PALLETIZER.

EE WAS OPERATING A DOZER. AS HE TURNED HIS HEAD TO LOOK TO THE REAR HIS HEAD STRUCK THE HANDLE OF THE FIRE EXTINGUISHER WHICH WAS MOUNTEDF IN THE CAB. THIS LACERATION REQUIRED STITCHES.

WHILE EE WAS AIR LANCING WALL ON PREHEATER, DUST BLEW INTO HIS EYES. CORNEAL ABRASION REQUIRING PRESCRIPTION MEDICATION.

WHILE REMOVING ROCKS FROM CRUSHER MATERIAL FLEW INTO EYE.

EE WAS CHANGING OUT A CEMENT LINE. PRESESURE FROM PUMP BLEW CEMENT INTO HIS EYES.

EE WAS REMOVING DRILL STEEL SU0PPORT FROM BEHIND DRILL STEEL. ROTARY HEAD NEAR TOP OF TRAVEL TOWER SWUNG AND PINNED EE'S ARM AGAINST TOWER.

PREHEATER WAS PLUGGED WITH HOT MATERIAL. AS EMPLOYEE APPROACHED MAN DOOR, LARGE PIECE OF MATERIL FELL CAUSING HOT MATTERIAL AND HOT AIR TO BLOW BACK THORUGH DOOR,WHICH HIT EMPLOYEE.

THE EMPLOYEE WAS INJURED WHEN HE WAS STRUCK BY A 2 1/2" AIR PIPE. HE WAS ATTEMPTING TO BLEED THE AIR LINE, ALONG WITH A FELLOW EMPLOYEE, BY USING A BALL VALVE THAT WAS INSTALLED IN THE SYSTEM. WHEN THE VALVE WAS OPENED THE FORCE OF THE ESCAPING AIR CAUSED THE PIPE TO TURN AND UNTHREAD FROM THE FLANGE THEN STRIKE THE EMPLOYEE.

WHILE CLEANING CRUSHER DECK ROCK FELL FROM ABOVE AND STRUCK HAND.

EE WAS USING A PORTABLE GRINDER WHEN IT KICKED BACK AND PUSHED HIS HAND INTO THE WORK CAUSING THE INJURY.

JACK HAMMER WAS STUCK, TRIED TO PULL IT OUT.

EE WALKED UNDER AREA OF TORCH CUTTING A 2" CHANNEL IRON STRUCK EE IN RIGHT SHOULDER AREA.

EE WAS CUTTING BOLTS FROM BEAMS WITH TORCH. BOLTWAS CUT LOOSE AND FELL INTO EE'S BOOT CAUSING BURN TO RIGHT ANKLE.

WHILE WELDING INTHE OVERHEAD POSITION, HOT SLAG DRIPPED DOWN SLEEVE OF WELDING JACKET AND ROLLEDDOWN INTO GLOVE, CUASING BURN

WHILE SHOVEL OPERATOR WAS TRAVELING, THE DRIVE SPROCKET RODE UP ON THE TRACK THEN FELL 8 INCHES BACK INTO PLACE.

WELDING HELMET DID NOT PIVOT PROPERLY.

EE WAS SETTING UP A STACKER WHEEL AND ADJUSTING CHUCK TO DIAL. WHEEL FELL OUT OF CHUCK AND STRUCK EE'S LOWER RIGHT LEG, CAUSING A GASH IN THE LEG.

EE WAS USING 110V 1/2" DRILL WHICH AGGRAVATED AN EXISTING ELBOW CONDITION.

EMPLOYEE WAS INJURED USING A TENSIONING TOOL TIGHTENING A DUST COLLECTOR BAG. TOOL SLIPPED OFF STRIKING THE EMPLOYEE IN THE MOUTH CHIPPING A TOOTH.

INJURED AND ANOTHER EMPLOYEE WERE WORKING WITH VACTOR TRUCK. HOSE BECAME PLUGGED. WHEN OBSTRUCTION WAS RELEASED, SUCTION DREW EMPLOYEE'S ARM INTO HOSE.

EMPLOYEE WAS TACKING PAD EYES TO ROTOR, DID NOT GET LENGS FULLY CLOSED WHEN HE STRUCK ARC.

OIL LUBRICATING GUN FELL ON LEFT NASAL BRIDGE. NO OIL IN EYES, NO VISUAL CHANGES. I DID NOT REPORT THIS WITHIN THE 10 DAYS BECAUSE I WAS NOT AWARE OF STITCHES REC'D BY EE. UPON RECEIPT OF DR'S REPORT I FILED THIS REPORT