Buscar en el registro

Employee was attempting to transfer lanyard from structure to the basket of a boom lift and fell approximately 14'.

Hurt back while helping change lower deck screens.

While unloading screen panel from loader bucket onto catwalk, operator cut right wrist while setting it down on the catwalk.

Laborer was working on screen deck and twisted right knee while lifting screen.

Attempting to lift boat from water.

windy conditions, blowing debris around. debris entered eye around safety glasses

While placing a new belt on a dry El Jay screen catwalk, he turned wrong and heard knee pop.

While working on dredge ladder wind blew particles into right eye.

While shoveling rock from under conveyor, had sharp pain in back of neck.

While performing repairs to hazemag crusher, during repairs bumped elbow.

EMPLOYEE WAS WALKING ON CONVEYOR BELT. HE LOST HIS FOOTING. EMPLOYEE FELL 15 FEET 5 INCHES TO THE GROUND. POSSIBLE BACK, LUNG AND RIB INJURIES ON LEFT SIDE.

EXITING LOADER W/O 3-POINT CONTACT & MISSED THE STEP ON THE LADDER, HE FELL TO THE GROUND.

Operating Cat 992 loader.

Wiring secondary disconnect box without proper lock-out causing electrical burn to hand. Written disciplinary action taken.

PULLED GENERATOR OFF DREDGE & PULLED GROIN MUSCLE. ON 12/22/04, RE-INJURED MUSCLE STRAIN WHEN PULLEY & CABLE WERE DROPPED CAUSING FOCUS OF WEIGHT ONTO EMPLOYEE.

Another employee dropped ladder - hitting employee on head.

LIFTING CONVEYER BELT OF ROLLED STEEL.

Prying a 6' piece of steel, bar slipped off pinch point.

EE WAS STANDING ON CATWALK THAT SURROUNDS SCREEN & ATTEMPTED TO LIFT A 2" SCREEN UP TO A CO-WORKER WHO WAS ON TOP OF SCREEN. WHILE LIFTING THE SCREEN, EE FELT A PULLING SENSATION IN HIS RIGHT GROIN AREA. HE WAS SENT TO 1ST HEALTH CARE & WAS DIAGNOSED WITH AN INGUINAL HERNIA.

DRILLING, SLIPPED & STRAINED SIDE.

USED BAR TO THROW A VALVE. BAR SLIPPED SMASHING HIS FINGER.

BRICKING KILN, BECAME OVERHEATED, APPEARED TO HAVE HEAT EXHAUSTION, TRANSPORTED TO E.R.

EE REMOVING CHUNK OUT OF SAND SCALE WITH SLEDGE HAMMER. CHUNK FELL OUT ONTO LEG. EE PUT ON LIGHT DUTY AFTER DR'S APPT ON 7/21/03.

DUST WAS BLOWN INTO EMPLOYEE'S RIGHT EYE.

ENERGIZED ELECTRICAL WIRE TOUCHED GROUND SURFACECAUSING FLASH AND BURN TO EMPLOYEE'S FACE AND HANDS.

EMPLOYEE KNOCKING DOOR ON #4 FINISH MILL WITH SLEDGE HAMMER STRAINED LEFT SHOULDER.

EE BECAME ILL WHILE WELDING IN AN ENCLOSED AREA.

EE EXITED TRUCK TO CHECK TAILGATE & WAS CLEANINGMATERIAL FROM THE TAILGATE PIN. WHEN AIR OPERATED LATCH ACTIVATED OPENING THE CLOSING ON LEFT HAND CRUSHING IT

CHANGING FLOW OF CEMENT FROM ONE SILO TO ANOTHER, PULLED SLIDE AND DUST BLEW UP IN EYES.

EE WAS CLEANING OFF DUST ON TOP OF COOLER WITH AIR LANCE. HE WAS WEARING A FACE SHIELD & SAFETY GLASSES BUT THE DUST BLEW UP UNDER HIS SHIELD & GLASSES INTO HIS LEFT EYE.

EE WAS MAKING HIS WALK AROUND ON #4 DUST COLLECTOR. TURNED AROUND AND CAUGHT HIS FOOT ON A TOE GUARD. TRIPPED AND FELL ON LEFT WRIST.

EE WAS GIVEN JOB ASSIGNMENT TO WORK IN DUST COLLECTOR. HE WAS ALSO INSTRUCTED BY SUPERVISOR TO WEAR GOGGLES IN THIS AREA. EE IGNORED THE SAFETY INSTRUCTIONS & WORE REG. SAFETY GLASSES. THERE WAS A MAJOR DUST FALL & EE GOT DUST IN EYE. 1ST AID WAS GIVEN 9:15AM. OVER WEEKEND EYE BECAME INFECTED AND INFLAMMED. DR. ON THE 28TH PUT EE OFF WORK UNTIL 11/4.

ANNUAL HEARING TEST REVEALED A 25 DB SHIFT IN RIGHT EAR. SEE ATTACHED COPIED OF TEST & LETTERS.

EE WAS TIGHTENING A SPANNER NUT WITH A HAMMER AND A CHISEL BIT FROM A CHIPPING HAMMER. PIECE OF THE CHISEL BROKE OFF AND PUNCTURED LEFT ARM OF EE.

EMPLOYEE WAS CLOSING TAIL GATE ON DUMP TRUCK AND CAUGHT FINGER WHILE GATE WAS CLOSING. SPLIT LEFT INDEX FINGER. SUTURES REQUIRED.

HOT CLINKER ON CONVEYOR BELT. TEMP SENSOR MALFUNCTION SHOWING A 300 READING WHEN ACTUALLY TEMP WAS 700 DEGREES. BELT WAS ON FIRE THAT LASTED MORE THAN 30 MINUTES. WAS PUT OUT WITH EXTINGUISHER S.

MANUALLY TURNING CRANE BUCKET HE CAUGHT LEFT THUMB ON METAL SPUR CAUSING A LACERATION OF THUMB.

CUTTING BELT (FLASHING) WHEN KNIFE SLIPPED & CUT LEG.

EMPLOYEE WAS CLEARING A PLUG IN THE PRE-HEATER BUILDING THROUGH A POKE HOLE. HE WAS NOT WEARING THE PROTECTIVE COAT, FACE SHIELD & USING A SHORT AIR LANCE. THESE ITEMS WERE AVAILABLE FOR USE. HOT FEED BLEW OUT THE POKE HOLE & CAUSED SECOND DEGREE BURNS ON ARMS, BACK & FACE.

EE SLIPPED WHILE WORKING ON PUMP-LOSS BALANCE.

EMPLOYEE DRAGGED CHARGED AIR LANCE ACROSS FLOOR; VALVE OPENED; LANCE TOOK OFF & HIT SAFETY GLASSES & CUT FACE ABOVE RIGHT CHEEK.

EMPLOYEE CARRYING HEAVY TOOLS ON SHOULDER WHILE CLIMBING LADDER TO GET TO CRANE. RESULT WAS SEPARATION OF RIGHT SHOULDER.

EMPLOYEE HOLDING WRENCH FOR ANOTHER EMPLOYEE TO HIT WITH HAMMER. EMPLOYEE MISSED WRENCH AND HIT THUMB OF 1ST EMPLOYEE.

EMPLOYEE WAS WORKING ON ELEVATOR DOORS WHEN ONE OF THE TENSION BARS CAME LOOSE AND STRUCK THE EMPLOYEE IN THE BACK OF THE HEAD.

WALKING OUT OF OFFICE, STEPPED OFF A STEP AND IMMEDIATELY WENT TO THE GROUND.

PICKED UP BEARING TO MOVE, SWUNG AROUND & SMASH-ED LEFT LITTLE FINGER AGAINST HANDRAIL.

EE WAS IN SILO CLEANING MATERIAL. AIR FLOW FROM HOLE IN BOTTOM WAS BLOWING CEMENT INTO EE EYES. PROPER PPE WAS NOT WORN.

MOVING OIL BARRELS USING 2 X 4 BOARD, IN PROCESS HAND SLIPPED AND THE BOARD STRUCK THE RIGHT HAND.

WELDER WAS BEING LOADED INTO PICKUP TRUCK. WHILEGUIDING WELDER HIS FINGERS WERE CAUGHT BETWEEN EQUIPMENT AND WELDER.

EMPLOYEE WAS CUTTING CLINKER BELT WITH UTILITY KNIFE, CUTTING MOTION WAS TOWARD EMPLOYEE BLADE PIERCED RIGHT THIGH. 3 STITCHES WERE NECESSARY.