Buscar en el registro

HE WAS HELPING MOVE A GEAR BOX, WHEN THE SHAFT HE WAS HOLDING BROKE, SNATCHING & SPRAINING HIS RIGHT HAND. AFTER REST DID NOT HELP THE HAND TO HEAL, SURGERY WAS PERFORMED ON 4/18/02 TO REATTAC H A LOOSE LIGAMENT IN THE HAND.

EMPLOYEE WAS IMPROPERLY REMOVING A DRILL BIT ON A FACE HOLE. THE BIT WAS SITTIG ON THE GROUND AND HE REACHED UNDER THE TABLE TO LINE THE BIT UP WITH THE HAMMER AS IT CAME DOWN. HIS THUMB WAS T OP OF THE BIT WHEN THE HAMMER CAME DOWN, AMPUTATING HIS LEFT THUMB. GLOVES WERE ON.

WAS TIGHTENING THE TENSION ROD AT THE PRIMARY CRUSHER WHEN THE ROD BROKE, AND THE TORQUE EXTENSION HANDLE END RAKED ACROSS HIS HAND CAUSING A DEEP LACERATION REQUIRING STITCHES TO CLOSE.

EE WAS MEASURING FOR WEAR PLATE C TWIN SAND SCREW WHEN HE WAS GETTING DOWN TO STRIKE HIS UPPER LIP INTO SAND SCREW. EE WAS WEARING ALL REQUIRED PPE PLUS SAFETY HARNESS.

EE WAS USING A PRY BAR TO REMOVE A ROCK FROM A CHUTE. THE BAR SLIPPED & HE HIT HIS FINGER ON THE EDGE OF THE CHUTE

EE WAS LIFTING SCREENS INTO PLACE ON THE BOTTOM DECK OF #2 SCREEN.

TIGHTENING TAIL PULLEY ADJUSTER NUT WITH 3/4" DRIVE RATCHET. RATCHET SLIPPED OFF OF NUT, CAUSING EMPLOYEE TO CUT PINKY FINGER ON RIGHT HAND BETWEEN RATCHET HANDLE AND ROCK ON THE GROUND.

EE WAS RAISING THE BALL LATCH ON THE GREASE TRAILOR WHEN HE TOOK PIECE OF STEEL PIPE AND TRIED TO KNOCK THE LATCH UP. WHEN HE DID HE SMASHED HIS LEFT RING FINGER BETWEEN THE PIPE AND THE THREE WAY HITCH.

WHILE TIGHTENING THE SCREWS TO A BREAKER IN AN ELECTRICAL BOX THE SCREWDRIVER MADE CONTACT WITH THE METAL FRAME CAUSING AN ELECTRICAL SHORT & F LASHBURNS TO EE'S EYES. HE WAS GIVEN PRESCRIPTIO N FOR HIS EYES.

WHILE TIGHTENING THE SCREWS TO A BREAKER IN AN ELECTRICAL BOX THE SCREWDRIVER MADE CONTACT WITHTHE METAL FRAME CAUSING AN ELECTRICAL SHORT AND ELECTRICAL BURNS TO EMPLOYEE'S FACE, EYES AND FOREARM.

EE HAD BEGUN CLIMBING A LADDER. HE HAD 2 SODAS IN HIS LEFT HAND AND WAS THEREFORE USING HIS LEFT ARM ON THE LADDER RUNG RATHER THAN HIS HAND. HE BEGAN WITH HIS LEFT FOOT ON THE 1ST RUNG AND RT . HAND ON A RUNG ABOUT HEAD HEIGHT. WHEN HE TRANSFERRED HIS WEIGHT ON RT. FOOT ON 2ND RUNG HIS FOOT SLIPPED CAUSING HIM TO FALL ABOUT TWO FEET TO THE GROUND CAUSING A SPRAINED ANKLE & CRACKED

PAD EYE ON JAW PLATE PULLED LOOSE NA DHIT EMPLOYEE ON THE LEFT SIDE OF NECK REQUIRING 4 STITCHES.

EMPLOYEE WAS CLIMBING OUT OF A CHUTE WHEN HIS FOOT SLIPPED AND HIS KNEE TWISTED.

EE WAS LOADING TRUCKS WITH A 980F WHEEL LOADER. THIS LOADER HAS FINGERTIP CONTROL AS TO SPEED AND BUCKET MANEUVERABILITY. EE NOTICED A STINGING SENSATION IN HIS RIGHT SHOULDER. AFTER SEVERAL H OURS THE PAIN DID NOT SUBSIDE SO MEDICAL ATTENTION WAS SOUGHT.

EMPLOYEE WAS PLACING SCREENS IN #2 SCREEN. HE WAS LYING ON HIS BACK BETWEEN DECKS 1 & @. HE WAS TURNING TO GO IN A BETTER BOYD POSITION WHEN HE STRUCK A SHARP PORTION OF THE UPPER DECK FRAME . WITH HIS RIGHT CHECK RESULTING IN A SMALL CUT IN WHICH THREE STITCHES WERE TAKEN.

EMPLOYEE WAS PRYING A ROCK LOOSE IN FEED HOPPER. IT ROLLED WHEN FREED AND STRUCK HIM IN LEFT KNEE.

EE WAS ATTEMPTING TO CLEAR A ROCK FROM THE TAKE UP PULLEY. EE WAS STANDING ON THE GROUND WITH LEFT HAND HOLDING THE PIPE THE TAKE UP PULLEY WEIGHT OPERATES IN. HE SIGNALED FOR THE BOLT TO BE B UMPED AROUND WHICH SHOULD CLEAR THE ROCK. WHEN THE BELT (BOLT?) WAS BUMPED THE COUNTERWEIGHT SWUNG SIDEWAYS PINCHING EMPLOYEE'S LEFT INDEX FINGER.

INJURED PERSON WAS ASSISTING IN THE REMOVAL OF A MOTOR SHIV ON THE PRIMARY JAW CRUSHER. UPON DISASSEMBLY THE SHIV FELL TO THE GROUND PINCHING HIS LITTLE FINGER ON THE LEFT HAND BETWEEN THE SHI V AND THE GROUND.

INJURED WAS CARRYING A PIECE OF METAL TUBING TO BE USED FOR A SCALE GUARD. HE SLIPPED AND FELL AND THE TUBING (WEIGHING 60-80 LBS) LANDED ON HISLEFT HAND.

FELL THROUGH JAW CRUSHER APPROX 10' MOVABLE JAW WAS NOT STATIONARY-EMPLOYEE WAS REMOVING A WEDGE.

THE EE WAS CHANGING A TOOTH ON HIS LOADER. HE USED A HAMMER TO HIT THE TOOTH AND LOSING IT UP. WHEN HE HIT THE TOOTH ON THE POINT END A CHIP CAME OFF AND HIT HIM IN HIS LEFT UPPER ARM BICEP.

EE WAS SHARPENING DRILL BIT WHEN WINDS BLEW PIECE OF HOT SILICA AROUND SAFETY GLASSES AND EMBEDDED ITSELF INTO EYE.

SHROUDS WERE BEING REPLACED ON THE CAT 990 LOADER BUCKET. THE NUTS WERE BEING REMOVED BY AN AIR IMPACT WRENCH & THE BOLTS HAVE A FIT TO PREVENT SPINNING. WHILE REMOVING ONE OF THE NUTS THE BOL T CAME OUT OF THE FIT WHILE EE WAS ATTEMPTING TO KEEP IT SECURE IN PLACE. THE BOLT SPUN & DUE TO THE SHARP EDGE CREATED BY WEAR ON THE BOLTHEAD CAUSED A LACERATION TO EE'S RIGHT INDEX FINGER

EE ATTEMPTING TO CUT RUBBER BELT INTO WHEN BOX KNIFE SLIPPED AND CUT LEFT THUMB REQUIRING 5 STITCHES.

THE TRUCK EMPLOYEE WAS DRIVING STALLED WHILE TRYING TO PULL UP THE RAMP FROM THE LOADING AREA, CAUSING THE TRUCK TO ROLL BACKWARDS DOWN THE RAMP AND TURNING OVER ON ITS SIDE WHEN THE TRUCK WENT UP THE EMBANKMENT TO STOP ITS ROLL. THE TRUCK LAID OVER ON THE SIDE OPPOSITE FROM THE CAB AND THE EMPLOYEE CUT HIS FOOT INSIDE THE CAB WHEN IT LAID OVER ON ITS SIDE.

GRIZZLY FEEDER WAS NOT WORKING PROPERLY/OPERATOR WENT TO DRIVE SYSTEM FOR A VISUAL INSPECTION/LEANING OVER MOTOR ALBWING HIS GLOVE TO BE CAUGHT PULLING HIS HAND INTO PINCH POINT CAUSING LACERA TION TO HIS HAND. GRIZZLY FEEDER

EE AND EE WERE TOLD TO CARRY SCREEN CLOTH TO THE TOP OF #2 SCREEN DECK, EE WAS BEING TREATED FOR A PRE EXISTING RIGHT SHOULDER PROBLEM. EE DID NOT MAKE THE FORMAN UNDERSTAND HE HAD A PROBLEM WITH HIS SHOUULDER. EE INJURED HIS RIGHT SHOULDER WORSE BY CARRING THE WEIGHT OF THE SCREEN CLOTH.

WHILE CUTTING INSULATION TO INSTALL A CONDUIT BOX, THE KNIFE THAT EMPLOYEE WAS USING SLIPPED, CUTTING EMPLOYEE'S LEFT THUMB. SIX STITCHES WERE REQUIRED TO CLOSE WOUND.

WHILE HELPING TO GUIDE A CRUSHER MOTOR INTO PLACE, EE'S LEFT FOOT SLIPPED OFF OF THE CATWALK (OTHER FOOT WAS ON THE MOTOR BASE)ONTO CONVEYOR C-1APPROX 36", HIS RIGHT HAND INDEX FINGER MADE CON TACT WITH THE MOTOR BASE WHERE IT WAS STRUCK BY A LINE BAR HE HAD BEEN HOLDING

A WELDER WAS WELDING A PLATE INTO THE PRIMATY DUMP HOPPER. INJURED (THE PRIMARY OPERATOR) WAS PRESENT. HE WAS CLEANING ROCK AWAY FROM ANOTHER AREA TO BE WELDED. HE WAS APPROX 5' FROM THE WELDI NG ARC.

EE WORKED HIS ENTIRE SHIFT IN THE HEAT 95 DEGREE AND DRANK A LOT OF FLUIDS. AFTER LEAVING WORK OAND RETURNING HOME DECIDED TO GO TO HOSPITAL BECAUSE HE FELT DEHYDRATED DR SAID HE HAD HEAT EXHA USTION AND INSTRUCTED HIM TO DRINK PLENTY OF FLUIDS AND TAKE A DAY OFF.

EE WAS EXITING A 7TON CRANE. FROM A SITTING POSITION ON A FLAT SURFACE WITH LEGS HANGING OVER THE SIDE PURPOSELY SHIFTED HIS BUTTOX & FREE FELL APPROX 24" TO THE GROUND INJURING HIS LEFT KNEE.

THE EMPLOYEE WAS FIXING A RUBBER WAER LLINE WHEN HE CUT THROUGH THE LINE WITH A KNIFE AND CUT HIS INDEX FINGER.

WHILE CHANGING SCREEN CLOTH ON #3 SCREEN TOWER, INJURED & EMPLOYEE WERE ATTEMPTING TO THROW USED SCREEN CLOTH FROM CUT WALK WHEN A PROTRUDING WIRE CAUGHT THE TOP OF INJURED'S RIGHT HAND CAUSIN G A 1" LACERATION REQUIRING 6 SITCHES.

EE WAS REPLACING A 1/2" ROLL PLATE TO COVER THE OIL DRUM IN THE DISTER SCREEN. THE 1/2" ROLL PLATE WEIGHT WAS APPROX. 140 LBS AND HAD BEEN CUT IN HALF FOR BEFORE HANDLING. THE 1/2" ROLL PLATE WAS SETTING ON A SCREEN BRACE INSIDE THE SCREEN WHEN IT FELL MASHING HIS LEFT THUMB BETWEEN THE SCREEN BRACE AND THE ROLL PLATE.

WHILE UNLOADING A NEW WELDING MACHINE, THE EMPLOYEE WAS HOLDING ON TO THE TIE DOWN STRAPS, WHICH WERE HOLDING WELDING MACHINE TO A PILOT. WHEN HE WENT TO DISMOUNT FROM THE VEHICLE, HE DID NOT LET GO OF THE METAL STRAP. HE CUT HIS RIGHT HANDRING FINGER AND HAD TO HAVE 5 STITCHES.

EMPLOYEE WAS USING A HAND GRINDER PREPARING A RUSTY METAL SURFACE WHICH WAS TO BE WELDED. EMPLOYEE WAS WEARING SAFETY GLASSES WITH A PAIR OF GRINDING GOGGLES OVER THEM. THIS EMPLOYEE HAS THIN NOSE AND THE NOSE PIECE OF THE SAFETY GOGGLES DID NOT GIVE AN ADEQUATE SEAL LETTING A PIECE OF METAL GO INTO CORNER OF EMPLOYEE'S EYE.

EE WAS STANDING ON A DESK BOLTING ITEM DOWN FROM A WALL. HE STEPPED FROM THE DUST INTO SWIVEL CHAIR WHICH HAD CASTERS ON THE BOTTOM. WHEN HE STEPPED INTO THE CHAI IT ROLLED TO THE SIDE CARTING HIM TO LOOSE HIS BALANCE AND FELL ON HIS BACK ONTO THE CONCRETE FLOOR.

EE WAS DRIVING BARFORD HAUL TRUCK WHEN HE NOTICED A PROBLEM WITH THE POWER STEERING. HE HAD TO STRAIN TO TURN THE STEERING WHEEL IN ORDER TO BACK TRUCK UP TO THE PRIMARY CRUSHER IN ORDER TO DU MP LOAD BEFORE TAKING TRUCK TO THE SHOP TO HAVE STEERING PROBLEM LOOKED AT. WHEN EXITING TRUCK, EE COMPALINED OF PAIN IN HIS BACK AND WENT TO DR.

WHILE CLEANING OUT BUILT UP MATERIAL WITH A HOSE AROUND TAIL PULLEY INSIDE TUNNEL EMPLOYEE REACHED ACROSS BELT TO SPRAY OUT AREA WHEN HIS LOOSE SHIRTAIL BECAME ENTANGLED IN UNGUARDED ROTATING SHAFT HE REACHED DOWN TO PULL SHIRT FREE & AS HEDID HAND SLIPPED & FINGER WAS CAUGHT BETWEEN PLATE ON END OF SHAFT & BEARING HOUSING DISLOCATING FINGER

WHILE TAKING JAM NUTS OFF OF SWINGING DYE AT PRIMARY CRUSHER A WELDING ROD HAD BEEN PLACED INTO A SOCKET TO HOLD IT ONTO AN AIR WRENCH. THE VICTIM WAS HOLDING AIR WRENCH FROM UNDERNEATH INTO PLACE WHEN HIS HAND SLIPPED INTO THE SOCKET AREA CAUSING THE WELDING ROD TO TEAR INTO LEFT HAND.

THE EMPLOYEE WAS WORKING ON THE ENGINE OF A CAT 769C HAUL TRUCK TO REMOVE A PISTON AND LINER. THE PISTON ROD NEEDED LINING UP. HE TOLD HIS HELPER TO "TAP IT". THE HELPER THOUGHT HE MEANT BUMP THE STARTER. THE MECHANIC SAID HE MEANT TAP ON THE PISTON WITH A TOOL. HIS HAND WAS CAUGHT BY THE PISTON ROD. HE SUFFERED A CUT AND SOME LIGAMENT DAMAGE TO HIS HAND.

EMPLOYEE WAS DRSIVING A 50 TON HAUL TRUCK FROM POINT LOADING TO PRIMARY CRUSHER THE HAUL ROAD NOT BEING PERFECTLY SMOOTH CAUSED EMPLOYEES SEAT TO BOTTOM OUT AS HE WENT OVER A WALL INTO A DIP W HEN THIS HAPPENED HE BEGAN TO EXPERIENCE BACK &&ARM PAIN LEG PAIN ON THE SIDE AFTER XRAYS HE WAS DIAGNOSED AS HAVING ACCUTECERVICAL LUMBAR MUSCLE GROIN & RELEASED

THE EMPLOYEE WAS PULLING A CABLE ON THE DRAGLINE. HE PULLED TOO HARD AND SPRAINED HIS LEFT SHOULDER.

DRILLER PREPARING TO ADD THIRD DRILL ROD (25'), AFER ATTACHING BOTTOM LOP OF ROD LSING, IGNORED SSAFETY POLICY BY NOT LOOKIN G UP TO BE SURE TOP LOOP WAS ATTACHED CORRECTLY. AFTER HOISTING RO D OUT OF ROD RACK, HE LOWERED IT OUT OF TOP RACK. BECAUSE TOP LOOP OF SLING WAS NOT AROUND ROD , TOP OF ROD TILTED OVER & DRILLER'S RIGHT GLOVED HAND WAS MASHED BETWEEN LOWER SIE OF ROD AND H

GREASING UNDE RWATER TRUNK. SAFETY SHOES WERE TO BIG. AS HIS FEET BENT HIS LEFT FOOT, HSI BIG TOE BECAME CAUGHT ON THE END OF THE STEEL PLATE AND PULLED OFF 1/2 OF THE TOE NAIL.

THE ROCK GUARD ON 1 SCREEN HAD BECOME WORD AND AS EE WAS CLEANING UP CONVEYOR SPILLAGE AROUND THE CONE CRUSHERS A PIECE OF ROCK WEIGHTING APPROX. 10 ACCORDING TO EE COME THERE THE GUARD AND ST ACK EE IN THE MIDDLE OF HIS BACK. THE ROCK FELL APPROX. 10-15 FEET. THERE WERE MINOR BRUISES NO DISCORDATION TO THE BACK.

EE WAS TRAINING TO OPERATE DROPBALL CRANE. DUE TO LACK OF ROOM INSIDE CAB, WAS STANDING OUTSIDE OBSERVING AND A SHARP FRAGMENT OF ROCK STRUCK EE ON THE INSIDE OF RIGHT FOREARM REQUIRING 6 STIT CHES.

THE INJURED PERSON WAS AN ELECTRICIAN HIRED TO RUN A GROUND FAULT TEST. WHILE RUNNING THE TEST AT THE SCALPING SCREEN PLATFORM, HE SAT DOWN ON THE HAND RAIL. WHEN THE WELD BROKE, HE LOST HIS B ALANCE AND FELL TO THE GROUND.

EE HAD LIFTED THE SAND SCREW SIDEPLATE NEARLY INTO PLACE EMPLOYEE SHIFTED PLATE TO ALIGN BOLT HOLES CAUSING A PLATE CLAMP TO LOOSEN SIDE PLATE FELL STRIKING EMPLOYEE HARD ACROSS THE LOWER BACK CAUSING COMPRESSIVE FRACTURES OF ONE OR TWO LUMBAR VERTABRAE