Inglis Quarry: 1 muerte registrada Metal/Non-Metal

Employee was struck by a rock on the back of his neck.

While lifting a screen, the EE twisted the lower back.

employee was using arc gauge hook up to welder cutting off rebar & all thread from form reinforcement. He went to throw away the used rod & part of it dropped off into his boot & burned his leg before he could get his boot off.

Twisted back working on #7 scale weight.

While holding loading plate in awkward position above head onto primary crusher, employee began to experience stiffness to his right shoulder.

The ee was driving the truck in the quarry when the truck hit a dip in the road. The ee complained of pain in his left elbow.

While in the plant using a grinder as part of his job duties the employee got a foreign matter in the right eye.

The employee was moving a junction box for the page 740 dragline. He was walking along side of the junction box as the 966 loader was carrying it with a chain. The chain slipped off hitting the employee in the upper lip.

Employee was getting off water truck picking up lunch box and hit elbow on top of radiator cover.

Piece of steel fell off of a table hitting and braking employees right toe behind the steel in his steel toed boots

Employee slipped off the water truck and injured the left knee.

Employee bent over to retrieve his lunch box when he felt a sharp pain in the middle of his back.

Employee was in haul truck and the loader operator put a load of material in the back of the haul truck. The load had a big boulder that bounced the employee while he was in the haul truck hurting his back.

Employee was trying to fix the fan blade of the air conditioner on a loader when he was cut by the blade causing a laceration on his left middle finger.

EE WAS PERFORMING THE TASK OF GREASING THE HEAD PULLEY OF A CONVEYOR. HE HAD FINISHED GREASING AND WAS ATTEMPTING TO VISUALLY CHECK THE BEARING. HE CLIMBED OUT OF THE GUARDED AREA ON TO THE CONVEYOR BELT WITHOUT FALL PROTECTION. HE SLIPPED AND FELL 30 FEET TO THE STOCKPILE BELOW.

EE WAS REMOVING SIDE PLATE ON #1 SCREEN WITH A PRY BAR AND PLATE POPPED OFF STRIKING EE IN FOREHEAD CAUSING LACERATION OF SKIN REQUIRING STITCHES.

EE STRUCK HIS LEFT KNEE WITH A SLEDGEHAMMER WHILE KNOCKING A WEDGE OUT OF A DRAGLINE CABLE

EE STEPPED ON A ROCK & FELL BACKWARDS ON HIS BACK & HIT ROCKS ON THE GROUND WITH HIS BACK

EE WAS CLIMBING OFF OF LOADER, STEPPED IN A TRENCH AND TWISTED RIGHT KNEE.

THE EMPLOYEE WAS CLIMBING BACKWARDS OFF THE GRADER. THE STEPS BENT UNDER THE EQUIPMENT. THE EMPLOYEE MISSED THE STEP AND FELL BACKWARDS ONTO THEGROUND ON HIS BACK AND RIGHT WRIST.

EE WAS ASSISTING WELDER ON WORK WITH PAGE 740 BUCKET. EE WAS SUPPOSED TO TURN HIS HEAD AND NOT LOOK AT THE WELDING ARC IN PROGRESS. EE CLAIMS HE COULD NOT TURN HIS HEAD IN TIME ON SEVERAL OCCA SIONS. LATER THAT NIGHT HIS VISION BLURRED AND HIS EYES BECAME IRRITATED.

EE WAS WALKING ON TOP OF DRAGLINE TUB & STEPPED INTO AN OPEN MANHOLE ACCESS

THE EE WAS TIGHTENING A 3/4" BOLT ON B CRUSHER AND STRAINED MUSCLE IN HIS FOREARM.

THE EQUIPMENT OPERATOR AND A MECHANIC WERE TEST RUNNING A MACHINE. THE OPERATOR APPROACHED A STEEP INCLINE, WHICH ACCESSES THE HAUL ROAD HILL, WHICH IS NOT PART OF THE REGULAR HAUL ROUTE. THE MACHINE WAS GEARED BY THE OPERATOR TOO HIGH, THE MACHINE LOST POWER, THE OPERATOR SHIFTED DOWN, AND THE DRIVELINE BROKE, AS THE MACHINE ROLLED BACK. THE MACHINE OVERTURNED ON ITS SIDE AS IT WA

EMPLOYEE WAS RETURNING BACK TO THE SOUTH PIT INAR35 EUCLID. HE WAS APROACHING A NARROW PASSAGE AT A COLVERT DITCH WHICH IS GUARDED BY 2.5' X 6'CEMENT BLOCKS LINED ON EACH EDGE. EMPLOYEE STRUCK THE BLOCKS WITH THE RIGHT FRONT WHEEL CAUSING THE TIRE TO DEFLATE INSTANTLY. THE STEERING WHEEL WAS PULLED TOWARD THE RIGHT, SPRAINING EMPLOYYESLEFT SHOULDER.

A NEW EE WHO WAS IN TRAINING WAS GREASING MOBILE EQUIPMENT WITH THE GREASE GUN. THE HOSE BECAME TWISTED. THE EE SWUNG THE HOSE TO UNTWIST IT, AND AS HE DID THIS THE VICTIM WAS STRUCK ON THE HE AD ABOVE HIS LEFT EYE CAUSING IT TO LACERATE. STRUCK BY GREASE GUN.

EE WAS REMOVING MATERIAL FROM THE PRIMARY HOPPER AND A BOULDER FELL ON HIS RIGHT HAND. INJRING HIS POINTER FINGER.

THE AREA WHERE ACCIDENT OCCURED WAS ABOUT 1'-2 !1/2' DEEP IN WATER. THE AREA WAS USED TO WASH OUT FROM UNDER A CONVEYOR. THE EE WAS ATTEMPTING TO ACCESS THE CONVEYOR TO GREASE AND HE SLIPPED N EAR THE HOLE WHILE HE WAS PULLING THE GREASE HOSE, HE TWISTED HIS KNEE.

EMPLOYEE PICKED UP TORCH AND THE HOSE HAD A HOLE IN IT WHICH CAUSED FLAME TO COME OUT AND BURN THROUGH THE WORKGLOVES AND BURN THE LEFT THUMB.

WHILE PULLING OFF A SPINDEL WITH TWO OTHER PEOPLE EE S HAND GOT TRAPPED IN BETWEEN THE FORKS OF A BOBCAT AND THE SPINDEL THIS CAUSED THE FINGER ON HIS LEFT HAND TO BE BROKE AND CUT.

EE WA WARNED ABOUT HIGH VOLTAGE WIRES OVERHEAD AND PROCEEDED TO LIFT A BOOM INTO THEM CAUSING HIM TO BE SHOCKED AND THROWN TO THE GROUND. AS A RESULT OF THE FALL HE SUFFERED SERIOUS INJURY TO HIS RIBS AND A HEAD WOUND. THE ELECTRICITY INVOLVED CAUSED HIM TO SUFFER A BURNED TOE.

A HOIST TRAVEL BEAM FELL UNDER LOAD WHILE EMPLOYEE TRIED TO GET AWAY HE CUT HIS SHOULDER REQUIRING 4 STITCHES.

WHILE DRIVING FUEL TRUCK, DEBRIS WAS BLOWING AROUND AND GOT INTO EYE.

EE WAS DRIVING AN EMPTY HAUL TRUCK BACK TO THE PIT TO BE RELOADED. AS HE WAS IN THE APPEX OF A 45 DEGREE CURVE, HE HEARD AND FELT A POP AND LOST STEERING CONTROL. THE EE APPLIED HEAVY BRAKING BUT WAS UNABLE TO STOP THE TRUCK BEFORE IT WENT OVER 2 FT DIRT BERM, INTO A CNAL CONTAINING APPROX. 5-6 FT OF WATER. THE 80 GALLON HYDRAULIC TANK MOUNTED TO THE LEFT SIDE OF THE TRUCK FRAME HA

WORKING SOLID LINE CAP BLEW OFF STRIKING FOREHEAD ABOVE RT EYE

EMPLOYEE REACHED INTO THE SWEEPER WITH LEFT HAND TO BEND BACK CORNER, PIECE OF METAL ON CENTER HIT LEFT INDEX FINGER.

HE WAS WORKING IN A TRANSFORMER THAT WAS ON A SKID WHICH HAD A HOLE IN IT.HE STEPPED BACKWARDS AND HIS LEFT FOOT WENT INTO THE HOLE.HE FELL BACKWARDS WITH HIS BODY ON THE GROUND AND HIS LEFT L EG IN THE HOLE.

HE WAS CHANGING OUT MOTOR IN TOP OF 740 DRAGLINE. IT HAD TWO COMEALONGS ON IT ONE OF THEM SLIPPED PINNING RIGHT HAND AGAINST WALL.

WHILE REMOVING SHANK ON DRAGLINE BUCKET, ANOTHER EMPLOYEE SLIPPED WITH 20 LB SLEDGE HAMMER AND HIT SECOND FINGER LEFT HAND.

WORKING ON SUMP PUMP PLANT PRYING WITH PRY BAR FELL BACK ON STEEL PIPE TWISTING HIS BACK

WHILE USING WRENCH TO TIGHTEN BOLTS WRENCH SLIPPED OFF BOLT & THIRD FINGER OF RT HAND WAS PINCHED BETWEEN THE WRENCH & THE WALL OF THE CRUSHER

WHILE DISMOUNTING THE PAGE 740 DRAGLINE, EMPLOYEE SLIPPED ON LAST RUNG OF LADDER AND THEN GRABBED LADDER WITH LEFT HAND TO KEEP FROM FALLING, HURTING LEFT SHOULDER.

HE WAS PUTTING WEAR PLATE IN POWER SCREEN AND TRYING TO PUT PLANT LINE IN; STRAINED BACK.

EMPL STATED HE WAS IN CATCHING BALL POSITION ONE KNEE DOWN & PULLING HOSE FROM TRUCK & HE WENT TO STAND UP & LEG LOCKED & HE COULDN'TMOVE.

HE WAS PULLING CHAIN ON WHINCH TO LIFT GREASE TUB ONTO DRAGLINE HIT LEFT INDEX FINGER ON SHARP EDGE OF T HANDLE, CUTTING THE TOP OPEN OF LEFT INDEX FINGER.

WHILE USING GRINDING DISC; GOT STEEL IN LEFT EYE.

SAT DOWN AT COMPUTER FELT LIGHT HEADED FELL STRIKING LEFT SIDE OF FOREHEAD & LACERATING & LANDING ON LEFT SHOULDER ON FLLOR UNCONSCIOUS FOR APPROX 15 MINS.

STEPPED ;ON NAIL, WENT THROUGH BOOT IN BOTTOM OF R FOOT

CUTTING TAPE WITH KNIFE, IT SLIPPED FROM HAND WENT IN L KNEE

HE WAS TRYING TO ALIGN BOLT HOLES ON DRAGLINE BRAKE BAND.PRY BAR SLIPPED AND FINGER TIP WAS PINCHED OFF (RIGHT INDEX).

WHILE COMING OFF DRAGLINE, SLIPPED AND FELL WHILE ON SHOE OF DRAGLINE, HIT RIGHT ARM.

HE WAS HELPING WELDER ALL DAY IN A DARK TANK IN CLOSE SURROUNDINGS AND WAS FLASHED SEVERAL TIMES.

WHILE CHECKING ELECTRICAL WIRING ON THE ROOF OF THE DRAGLINE,METAL FLAKES THAT THE PAINTERS WERE SCRAPING OFF BLEW INTO RIGHT EYE.

HE WAS TRANSFERRING MATERIAL WITH A FRONT-END LOADER. HE HAD THE BUCKET TOO HIGH IN THE AIR FOR THE TERRAIN. THE LOADER TOPPLED OVER, THROWING HIM FROM THE CAB.

TWISTED RIGHT WRM AT THE ELBOW WHILE LIFTING A 55 GALL BARREL ONTO THE BED OF A COMPANY PICKUP TRUCK.

HE WAS PUTTING A PIECE OF PIPE INTO LATHE AND WRENCHED HIS BACK.

HE WAS USING A TORCH WHILE CUTTING SCREEN IN A SHAKER DECK TOOK SAFETY GLASSES OFF TO GET A BETTER LOOK THEN RESUMED CUTTING WITHOUT PUTTING GLASSES BACK ON

HE WAS LIFTING SHANK FROM DRAGLINE BUCKET; SLIPPED & TWISTED LOWER BACK.

LIFTING TIMBER AND STUMBLED AND ATTEMPTED TO MAINTAIN BALANCE CAUSING PAIN IN THE LEFT GROIN AREA.

ATTEMPTING TO LIFT A STEEL LID WHICH THEN FELL AND PINCHED THE MIDDLE FINGER ON LEFT HAND.

PULLING ON SCAFFOLDING & INJURED SHOULDER

CARRYING CABLE TRAYS & STEPPED BACKWARD INTO A HOLE & HURT RIGHT LEG

GOUGING OUT WELD AND HOT SLAG FELL INTO LEFT SHOE AND BURNED FOOT.

FOREIGN OBJECT EMBEDDED IN EYE.

WAS CHIPPING SLAG OFF OF WELD IN AN ENCLOSED APCE WITH AN AIR SCALER AND A PIECE OF SLAG FLEW INTO HIS EYE

EMPL SPILLED DIESEL ON BOTH FEET THEY LATER BLISTERED & GOT INFECTED. DID NOT REPORT INJURY UNTIL 10/17/89 WHEN HE SOUGHT MEDICAL ATTENTION.

EMPL WAS USING AN AIR GRINDER AND SOME DUST WENT UNDER HIS WELDING HOOD PAST SAFETY GLASSES INTO HIS L EYE

SHE WAS WALKING DOWN INCLINE, LOST HER FOOTING. I FELL, BREAKING HER RIGHT LEG.

SAFETY GLASSES FOGGED UP DID NOT SEE OVERHANG, OVERHANG PUSHED GLASSES OFF AND CUT NOSE ON UPPER LEFT NEXT TO EYE AND UNDER BROW ON LEFT EYE, KNOCKED OFF HARDHAT.

HE WAS WORKING ON TUB WHEN CHUNK OF METAL FELL IN HIS BOOT AND WAS BURNING HIS FOOT, HE COULD NOT REMOVE HSI BOOT, THE BURN IS ABOUT THE SIZER OF A QUARTER AND WAS BLISTERED AND RED AND BURNS .

OVERCOME BY HEAT FROM SUN AND WELDING.

LIFTING CROSSTIES IN AWKWARD POSITION, PULLED BACK, OFF WORK ONE DAY FOR REST.

SWEAT & OIL IN EAR-HURTING-EAR INFECTION.

WHILE RIDING IN LOADER HIT BUMP & CAME DOWN HARD ON SEAT

HE WAS LIFTING STEEL PIN FROM FAIRLEAD TO LOAD ONTO A TRUCK AND PULLED A MUSCLE ON RIGHT SIDE OF LOWER BACK.

HE WAS ON DRAGLINE WALKING & FOOT CAUGHT ON LOOSE BOLT IN FLOOR-SLIPPED AND FELL ON LEFT HAND.

HE WAS WORKING ON LAB TRUCK BRACE THAT WAS HOLDING THE HOOD OPEN SLIPPED OFF AND THE HOOD CAME DOWN ON HIS LEFT HAND ABOVE THE KNUCKLES.

HE WAS CRAWLING UNDER TRUCK IN MUD KNEELING IN MUD ON ROCK HE COULDNT SEE & HIS RT KNEE TWISTED & HE HEARD CRACKING NOISE

I,NAME WALKED INTO THE PARTS ROOM & OTHER EMPLOYEE CAME AROUND THE CORNER WITH AN AIR HORN & SET IT OFF CLOSE TO HIS EAR.

HE WAS RUNNING THE CRUSHER WHEN HE TURNED FROM THE SURGE LINE TOWARDS THE WOBBLERS, SOMETHINBG HIT HIM IN THE LEFT EYE.

HELPING WELDER WORK ON CATWALK AND GLANCED UP OVER AT THE WELDER COUPLE OF TIMES AND WOKE 10:00 PM WITH FLASH BURNS.

HE WAS PREHEATING A BAR ON DRAGLINE BUCKET AND A PIECE OF HOT METAL FLEW INSIDE HIS GOGGLES AND BURNING BOTH EYES

THOUGHT WELDER HAD FINISHED AND LOOKED OVER -GOT FLASHBURN IN BOTH EYES.

HE HURT HIS BACK SHOVELING MATERIAL.

WORKING IN SHOP BENT OVER AND PICKED UP AXLE AND LOWER BACK POPPED.

FALSH BURN TO LEFT EYE DOING MACHINE WORK LOOKED OVER AT WELDER. INJURY WAS NOT REPORTED UNTIL 12-19-88.

LIFTING RAILROAD TIE TIE SLIPPED AND HYPER EXTENDED LEFT THUMB.

HE WAS WORKING ON CONVEYOR BELT CUTTING DRIP PAN: RT FOOT SLIPPED OFF ANGLE/IRON, HE FELL BACKWARDS - CAUGHT SELF WITH RT. ARM. LEFT LEG HOOKED, WRAPPED AROUND BAR.

HE WAS GETTING DOWN OFF LOADER AND STEPPED ON ROCK WITH RIGHT ANKLE TWISTING AND BREAKING IT.

HE WAS WORKING AND CHAIN SLIPPED ON COME A LONG WHILE MOVING A PIECE OFEQUIPMENT FROM BACK OF PICK UP TO DRAGLINE.

HE WAS COMING DOWN FROM A RAIL OFF DRAGLINE BY ONE OF THE LEGS AS HE PUT HIS FEET ON THE GROUND HE LET GO OF THE RAIL & HE SLIPPED & T WISTED HIS LEFT KNEE

WORKING ON DRILL RIG AND BENT DOWN TO JPICK UP TOOL AND AS HE WS LIFTING IT AND SWING ING AROUND FELT SOMETHING POP IN BACK.

HE WAS GETTING DOWN OFF LOADER AND HIS FOOT SLIPPED WHEN HE WENT TO GRAB LADDER. HE MASHED HIS KNUCKLED OF RIGHT HAND.

HE WAS CUTTING BOLTS WITH TORCH AND SLAG FLEW BACK LANDING ON HIS LEFT HAND BURNING IT.

HE WAS WELDING AND CHIPPED SLAG AND A PICE WENT INTO LEFT EYE.

WHILE CUTTING WITH A TORCH AT DRAGLINE BUCKET TORCH BLEW FIRE BACK INTO FACE

HE BENT DOWN TO PICK UP EDGE OF EUCLID TRUCK HUB TO PUT ONTO HAND TRUCK TO MOVE IT, SHARP PAIN APPEARED IN LOWER BACK.

HE WAS CRAWLING THROUGH A CHUTE HOLE ON SECONDAY SHAKER & CAUGHT RIBS ON METAL PLATE.

HE WAS SITING ON THE CRUSHER STAIRS EATING A SANDWICH WHEN HE WAS HIT ON THE LEFT SHOULDER BLADE BY A GOOD SIZED ROCK.

DOING MAINTENANCE ON STACKER CONVEYOR BELT HIT RT.SHOULDER ON BEAM

ISN,T SURE HOW OR WHEN INJURY OCCURRED HIS LEFT EYE STARTED HURTING.

HE LOST H IS BALANCE & FELL FROM CONVEYOR WHILE WORKING IN PLANT

I.NAME WAS USING STEAM CLEANER IT SLIPPED OUT OF HIS HAND STEAM BURNED HIS RT.ARM

HE WAS WORKING ON PRIMARY SHAKER TOP ON 5-19-88. STOOD UP HIT HEAD ON CROSS BEAM. ON 5-23-88 WAS WORKING ON FEEDER JAMMED HEAD ON CROSS BEAM.

CLIMBED UP ON WATER TRUCK BACK POPPED.

I.NAME ON 051788 REPORTED HIS LEFT SIDE & STOMACH WAS HURTING & HE THOUGHT HE MIGHT HAVE HURT HIMSELF WHILE REPLACING CONVEYOR BELT ON 051288 HE WENT TO DOC.& WAS DIAGNOSED AS POSSIBLE KIDNEY STONES NOT WORK RELATED ON 052188 WE GOT ANOTHER REPORT FROM DOC.LISTING SACROLIZE JOINT STRAIN AS INJURY

HOSING OUT THE THROUGH STACKER BELT TIGHTENED UP MUSCLES IN BACK.

STRAINED BACK WHILE SHOVELING AT PLANT.

OIL LEAK FROM CHAIN CASE SLIPPED IN OIL & FELL LANDING ON HIS BACK

HE PULLED MUSCLE IN LOWER RIGHT BACK PULLING HOSE UP BELT LINE.

CALLED IN 010588 SAID HE STRAINED HIS LOWER BACK & GROIN LIFTING BOXES OF EXPLOSIVES & LOADING HOLES

HE WAS BENT AT 4AIST PULLING FROM LEFT TO RT.ON DRIVE BELT ON WOBBLER ON PRIMARY CRUSHER TO LINE UP DRIVE TRAIN CHAIN FELT SOMETHING PULL IN LOWER BACK

HE WAS HELPING 8RILL CREW DRILL HOLES-STEPPED IN HOLE & TWISTED LEFT ANKLE.

HE WAS DRIVING 5OADED HAUL TRUCK UP RAMP TO UNLOAD AT CRUSHER.LEFT WHEELS RAN UP ON BANK AND CAUSED TRUCK TO ROLL ONTO ITS RIGHT SIDE.RIGHT LEG AND FOOT BRUISED AND SCRAPED AND RIGHT SIDE TRAN SPORTED TO 7 RI5ERS EMERGENCY ROOM VIA CITRUS COUNTY EMS AMBULANCE.

ON 12 HR.SHIFT 1ERFORMED NORMAL ROUTINE WORK FELT OKAY DURING MAJORITY OF SHIFT AROUND 400-500 NOTICED PAIN STARTING IN LOWER RT.BACK HIP AREA BY SHIFTS END AT 700PM HAD DIFFICULTY GETTING IN TO CAR TO GO HO4E DURING PREVIOUS WEEK NOTICED SHOOTING PAIN IN RT.LEG CANNOT PINPOINT DAY & TIME

I.NAME HAD A SL5G BURN ON LEFT ELBOW WH ICH GFOT INFECT ED & HAD TO BE DRAINED BY DOC.ACCORDING TO A NOTE FROM THE DOC.IT WAS LIKELY JOB-RELAT ED

BACK PAIN-FLARE3UP OF INJURY HE WAS PUSHING BACK CATCH TROUGH ON SHAKER AND LOWER BACK JUST POPPED. MUSCLE SPASMS AND STABBING PAIN IN LOWER LEFT BACK.

HE WAS CLIMBING3BANK STEPPED ON LEDGE LEDGE BROKE HE FELL ON BARGE SLIP TRYING TO GET ON BOAT

I NAME WAS WASH3NG BELOW CRUSHER HOPPER FALLING ROCK HIT CENTER OF LOWER BACK

EMPLOYEE WAS FO5LOWING HAUL TRUCK-STARTED AROUND IT AND COLLIDED WITH ANOTHER HAUL TRUCK.

PATIENT LOOSENI3G BOLTS OR CONVEYOR BELT & SHOVELING DIRT FOLLOWING DAY OF ACCIDENT & EXPERIENCING PAIN IN UNIBILICAL REGION.

WORKING IN DRIL5 RIG #24 HYDRAULIC CYLINDER CAP FELL ON LEFT WRIST AND HAND

HE WAS USING SP9AYER, DIRT AND GREASE FLEW INTO RIGHT EYE.

HE WAS CLIMBING3DOWN LADDER IN PLANT THERE WAS A ROPE DOWN MIDDLE OF LADDER-FOOT GOT CAUGHT & HE FELL FOUR STEPS FROM BOTTOM

THE DOOR OF EUC5ID HAUL TRUCK SLAMMED ON HIS LEFT ANKLE AGGRAVATING AN OLD INJURY INJURY NOT REPORTED UNTIL 10-1-86 3:35 PM

I NAME WAS GETT3NG OFF DRILL-CLIMBING DOWN WITH HANDFUL OF TOOLS AND SLIPPED OFFTRACK STRAINING BACK

HE WAS WORKING 4ETAL DETECTOR IN THE PLANT AND FELL ACROSS IRON RAIL CRACKING 10TH RT RIB

A TRUCK WAS BEI3G TOWED OUT OF THE WATER AND THE CHAIN SNAPPED AND HIT HIM KNOCKING HIM DOWN AND INJURING RT SIDE AND BACK.

WHILE SERVICING3HASUL TRUCK HE CLOSED DOOR AND WHEN HE TURNED BACK AROUND IT HAD SWUNG BACK OPEN AND HE RAN IN TO IT.

GETTING READY T2 SET CYLINDER ON LOADER CYLINDER SHIFTED ON HOIST-HE JUMPED BACK OUT OF THE WAY (THE CYLINDER WOULDN'T HAVE HIT HIM) AND HIT HIS BACK ON BOOM TRUCK.

HE WAS LEAVING 7ONTROL ROOM & FELL OFF THE SIDEOF PLATFORM THEWIND BLEW THE DOOR & HE SLIPPED OFF EDGE OF PLATFORM.

I NAME WAS STEP1ING ON LADDER LOST HIS FOOTING AND FELL TO THE ROCKS BELOW FRACTURING HIS RT ARM

I NAME WENT TO 2IS SUPERVISOR AND STATED HE WAS COUGHING WAS LIMEROCK DUST I NAME WENT TO THE DR WHO HAD CHESTS AND SAID THE CAUSE WAS CHEMICAL BRONCHITUS.

HE WAS PUSHING 2N HYDRAULIC CYLINDER TO SET IN PLACE SLIPPED AND TWISTED RIGHT KNEE.

HE WAS RUNNING 8RILL RIG,WHEN A BOLT CAME LOOSE AND DRILL ROOM HIT LOWER LEFT ARM.