ALICO ROAD QUARRY Metal/Non-Metal

EE was attempting to turn a rotor on the Hazemag Impact Crusher when EE's right little finger became pinched between the blow bar and the inside liner of the crusher. Stitches were required and a fracture was also present.

EE was wiping face when they felt something in their eye. EE flushed the eye and that did make it better. EE was taken to an eye specialist and the foreign matter was removed from the eye with a mechincal probe and antiobitic eye drops were administered one time.

Electric motor shorted. Hydraulic line ruptured and sprayed turbo. Fire burned for 47 Minutes. NO injury

Employee was on back inspecting the inside of the sizing screen. As employee was crawling on back employee rested back on a dam causing employee pain to back. Employee was taken to clinic on 6/29/2018 and returned to full duty. On a follow up visit to the clinic on 7/12/2018 employee was put on restricted duty.

Employee was operating a haul truck and the bed of the truck was lifted by loader when the bucket pushed down material at the end of the bed. Bed lifted and came down shaking the truck.

EE was dismounting the 4600 Drag Line. When EE stepped on the second step from the top EE's foot slipped off. This caused EE to loose EE's handhold and fall to the ground. This resulted in a fracture to the LEFT hip. EE fell approximately 4'.

Employee suffered from a heat related illness while performing maintenance on a haul truck step

Employee suffered from a heat related illness while using a 1" water hose at the sand plant.

On Saturday October 4th, employee was welding a pipe from the trammel screen pan to our fines pump. Employee did not report any issues. Monday morning employee complaint about a sore back.

Employee informed that he felt "a little stiff" in the morning. He did not attribute it to any particular event at this time. We logged the incident in the first aid register at that time and followed up with him later that Friday. However on Tuesday morning 07/22/2014 he complained again of stiffness in his back. He was taken to a clinic. He was diagnosed with a strain back.

Employee complained about back pain on Wednesday 12/11/2013. He claimed that he felt OK through the weekend and Tuesday, but on Wednesday he reported some discomfort. He never reported this but until Wednesday 12/11/2013

A non-chargable incident occured at the end of the shift when the two dragline operators turned down the machine. One of the operators told his partner he believed he was having a heart attack. His partner called the EMS 911 and took him to the main gate. Five minutes later the ambulance arrived and took the employee to the hospital where he passed away about one hour later.

Two EE's were placing 6" PVC pipe at a tire wash. After gluing into place, they were back filling a Bobcat. As EE swung the backhoe for more material, injured EE reached down and pulled up on the pipe, the bucket of the backhoe passed, caught the tip of EE's right index finger between it and the end of the PV pipe, cutting a piece of skin.

The Counterweight did not line up with the saddle, a come-along was attached to the frame on the conveyor. He took a closer look to see what it was hanging up on and in the process put his hand on the frame of the take-up system, the weight shifted catching the tip of the middle and ring finger on his right hand between the frame and the weight.

While working on removing bucket pin on a 992 loader, dust went into employee's eyes, possibly from the exhaust from the Impact wrench while working in a confined area (employee was wearing prescription safety glasses with side shields).

Employee was splicing the wire for the installation of a replacement light fixture on the #2 Hazemag crusher, as he was cutting off the outer cover of the cable the knife slipped and cut his thumb.

Employee was washing down under the secondary plant screening tower with a water hose, when he lost his footing on the ground and fell.

Employee slipped off the last rung of a ladder and bumped his right knee on the catwalk surface of a conveyor on 2-16-05: (Employee requested medical attention for the first aid incident on 2/23/05, at which point he was taken to workers compensation.)

Employee was changing a broken blow bar in the Humbolt Primary crusher and a small sliver of the blow bar struck him in the left leg.

EE was attempting to tighten a bolt on the drag friction with a hand wrench. The wrench was struck by a drum bolt causing EE's ring finger on L. hand to become pinched between the wrench and drag friction. A fracture to the last digit of the ring finger on the L. hand was realized.

Employee bumped his knee on the machine, while making repairs on a 926 loader. NOTE: (EE sought medical treatment on January 17th, 2005; prior to this date, it was a first aid log entry)

Employee was removing a bearing sleeve from a shaft with a hammer and a shard of metal broke off and cut the employees left arm.

OPERATOR WAS RAISING UP THE BOOM. HE GRABBED THE MASS PIPE AND THE BOOM STABILIZER CRUSHED HIS FINGERS.

EE WAS LAYING OUT BOOSTERS ON SHOT & GROUND WAS MUDDY. EE SLIPPED AND STRAINED HIS BACK WHILE TRYING NOT TO FALL.

THE EE WAS EXITING HER PICKUP AT THE 4600 DRAGLINE WHERE SHE WORKS, WHEN SHE WENT TO CLOSE THE DOOR, SHE REALIZED THE SEATBELT IN THE WAY AND WENT TO GRAB IT, WHICH CAUSED HER TO CATCH HER RIGHT HAND IN THE DOOR AS IT CLOSED.

Employee was welding inside the welding shop and his foot became entangled in the welding lead which caused him to fall and hit his shoulder on the floor. The ee did not seek medical treatment for the injury until Nov 24, 2004.

EE WAS WASHING OUT TAIL SECTION OF CONVEYOR WITH WATER HOSE WHEN A ROCK FELL FROM OVERHEAD CONVEYOR AND STRUCK EE IN HARD HAT.

WHILE GREASING THE BUCKET PINS ON A LOADER, THE HOSE FLEW OFF AND STRUCK EE ON THE RIGHT SHOULDER CAUSING A PUNCTURE WOUND.

WHILE UNDOING BOLTS FROM MACHINE, A PIECE OF A RUSTY METAL BOLT GOT INTO THE EMPLOYEES RIGHT EYE.

WHILE PREPARING TO SET BLAD ON D-9 DOZER EE LIFTED THE BLADE PUSH ARM & WAS NOT PROPERLY BALANCED MOVING & STRIKING THE EE IN THE RIGHT CALF SHIN AREA PUNCTURING THE SKIN & SWELLING THE LEG

CHANGING A HOSE ON THE PRIMARY ON THE GROUND LOW, WHERE TRUCKS DUMP INTO HOPPER, EE WAS IN THE AREA WEARING HIS HARD HAT, A ROCK CAME DOWN HITTING THE EE ON THE HARD HAT, HE FELL, HIS HARD HA T CAME OFF AND EE HIT HIS HEAD ON THE ROCKS.

EE TOOK OFF SAFETY GOGGLES TO CLEAN OFF DUST. WHEN HE FLEW INTO HIS GOGGLES A FOREIGN BODY FLEW INTO HIS RIGHT EYE. '

WHILE ATTEMPTING TO KNOCK A TOOTH OUT OF A LOADER BUCKET A METAL FRAGMENT PUNCTURED HIS RIGHT ARM.

EMPLOYEE WAS DRIVING HIS TRUCK AND HIT A SPEED BUMP, INJURING HIS STOMACH WALL.

WHILE EMPLOYEE WAS PULLING A PIECE OF METAL OUT OF THE CRUSHER HE CUT HIS LEFT THUMB.

EMPLOYEE PINCHED NERVE ON NECK WHILE WORKING ON THE LOADER.

WHILE BENDING DOWN TO PICK UP IMPACT IDLER EMPLOYEE FELT SHARP PAIN ON LOWER BACK.

EE LOST HIS BALANCE WHILE WORKING ON A LADDER AND FELL & BRUISED HIS ARM.

EMPLOYEE WAS CARRYING A STEEL PLATE DOWN A FLIGHT OF STAIRS WHEN HE SLIPPED & FELL CAUSING AN AVULSION OF THE LEFT THUMBNAIL.

EMPLOYEE WAS WALKING THROUGH THE YARD WHEN HE WAS STUNG NEAR THE RIGHT EYE BY A BEE.

EMPLOYEE STRAINED HIS LOWER BACK WHILE ATTEMPTING TO CATCH A HOSE WHICH WAS FALLING DOWN.

EE WAS HIT ON HIS HARD HAT BY A ROCK WHICH WAS THROWN OUT OF THE CRUSHER.

EE WAS CLEANING OFF THE DRAGLINE WHEN HE TURNED AROUND AND HIT HIS LEFT ARM WITH THE BOOM AND BRUISED IT.

EMPLOYEE WAS SWINGING A SLEDGE HAMMER WHILE DOING MAINTENANCE IN THE PLANT AND STRAINED HIS RIB CAGE.

EE STRAINED LEFT HOULDER WHILE OPERATING A FRONT END LOADER, LOADING HAUL TRUCKS WITH EXCAVATED LIMESTONE IN THE PIT.

EMPLOYEE BURNED LEFT FOOT WHEN A PIECE OF HOT METAL FELL INTO HIS BOOT. HE WAS CUTTING METAL WITH A TORCH.

EMPLOYEE DISENGAGED CLUTCH ON A MOTOR, AS HE WASREMOVING HIS HAND THE CLUTCH LEVER JUMPED OUT OF POSITION SMASHING THE MIDDLE FINGER OF HIS LEFT HAND.

EMPLOYEE WAS DOING A SERVICE ON 980F LOADER. HE UNSCREWED AND OIL SPILLED OUT ALL OVER EMPLOYEE GOING INTO BOTH EYES.

EE'S WERE INSTALLING A GEARBOX AND IT SLIPPED AND FELL CUTTING THE BABY FINGER REQUIRING THREE (3) STITCHES.

MISUSE OF CHEMICALS--EE WAS CLEANING HIS FRONT END LOADER WITH RIPPER II (A DEGREASER) AND MINERAL SPIRITS. HE BURNED BOTH HANDS. EE DID NOT USE GLOVES.

EE WAS REPAIRING A HAUL UNIT ENGINE USING A DRILL. THE ANGLE & POSITION OF THE DRILL & APPLYING PRESSURE AGGRAVATED MY RIGHT ELBOW. EE CHOSE NOTTO GO TO THE DR UNTIL 2/199 AT THAT TIME IT WAS DR FIRST CORTISONE INJECTION & IT BECAME DR. TREATABLE

EE ATTEMPTED TO CLOSE THE DOOR OF THE HAUL TRUCK. IT SLAMMED SHUT BUT DID NOT CATCH AND BOUNCED OUT AND BACK AGAIN AND CAUGHT RIGHT THUMB.

WHILE DRIVING THE OLD HANDLE OUT OF A SLEDGE AMMER, EE MISSED THE KEYSTOCK WITH A SMALLER HAMMER AND STRUCK HIS LEFT THUMB

WHILE ADJUSTING THE INTERLOCK FRICTION ON THE 4600 DRAGLINE, THE WRENCH SLIPPED OFF AND HIT HIM IN THE MOUTH.

EE WAS CLIMBING LADDER OF TRUCK WHEN HIS FOOT SLIPPED AND HE STRUCK HIS RIGHT HAND ON THE BUMPER OF THE TRUCK.

EMPLOYEE FELT IRRITATION IN LEFT EYE.

EMPLOYEE WAS TROUBLE SHOOTING FOR AN AIR LEAK ON BRAKES OF FRONT END LOADER WHEN HIS FINGER BECAME CAUGHT IN AIR CHAMGER.

A COIL OF WIRE WAS BEING PASSED TO ME AND THE SUN CAUGHT MY EYES AND THE TEST CLIP STRUCK ME IN THE MOUTH. IT CHIPPED THE FRONT TOOTH IN HALF.

THE BOOM ON THE CRANE COLLAPSED WHILE LIFTING THE CRUSHER. THE BLOCK STRUCK THE EMPLOYEE CAUSINGA POSSIBLE FRACTURE OF THE RIGHT ANKLE.

EMPLOYEE WAS CLIMBING LADDER TO CRUSHER CONTROL HOUSE. FOOT SLIPPED AND HE FELL CAUSING HIM TO INJURE RIGHT KNEE. (IT WAS RAINY AND THE GROUND WAS MUDDY).

EE WAS CLIMBING BACK INTO TRUCK HE HAD BEEN FUELING HIS TRUCK, HIS LEFT FOOT SLIPPED ON THE LADDER CAUSING HIM TO FALL TWISTING HIS RIGHT FOOT.

EMPLOYEE ATTEMPTED TO REMOVE RADIATOR CAP FROM DRAGLINE ENGINE, PRESSURE CAUSED HOT WATER TO SPILL OUT BURNING LEFT FOREARM.

EMPLOYEE WAS STEPPING OFF LADDER OF HAUL UNIT AND SLIPPED ON GRAVEL ON GROUND AND TWISTED RIGHT ANKLE.

EE WAS PUTTING A V BELT ON FEEDER PULLEY WHEN HIS FINGER BECAME CAUGHT BETWEEN THE BELT AND THE PULLEY LACERATION TO LEFT MIDDLE FINGER.

EMPL CLIMBED DRILL MAST TO LOWER CANOPY INTO ITS PROPER POSITION. WIND BLEW CANOPY TO RESTING POSITION,KNOCKING EMPL TO THE GROUND.

EMPLOYEE WAS CLIMBING LADDER INTO TRUCK AND SLIPPED HITTING LEFT KNEE.

CHECKED WATER IN RADIATOR OF WELDING TRAILER,STEPPED DOWN ONTO FRAME OF TRAILER.MISSED FRAME & FELL HITTING LEFT ELBOW AND RIGHT HAND ON GROUND.

PINCHED RIGHT INDEX FINGER WHILE WORKING ON A PULLEY WHEN INSTALLING A HUB AND BUSHING INTO A PULLEY PINCHING FINGER.

ASSISTING IN REPAIRING DRIVE BELT ON SIZING SCREEN. TENSION BOLT BROKE LOOSE FROM WELD STRIKING HIM IN RIGHT ABDOMEN, CHEST.

PREPARING TO GET UP IN HAUL UNIT EMPLOYEE PUT FOOT INTO CAHIN STEP AND SLIPPED AND FELL SPRAINING RIGHT FOOT.EMPLOYEE HAD MUD ON SHOE.

WHILE GRINDING WELD OFF DRAGLINE FLOOR TO INSTALL BRAKE GUIES PIECE OF METAL RUST BLEW & HIT FOREHEAD & LEFT EYE.

IT WAS FOGGY AND THE MOISTURE HAD COLECTED ON THE DRAGLINE AND WINDSHIELD. THE DRAGLINE OPERATOR WENT TO CLEAN THE WINDSHIELD AND SLIPPED AND FELL TO THE GROUND LANDING ON HIS LEFT WRIST.

RASH ON RIGHT WRIST.CUTTING PROCEDURES ON DRAGLINE BUCKET WITH AIR ARC EQUIPMENT USING COPPER COATED CARBON RODS,WEARING LEATHER WELDING GLOVES DUST APPARENTLY GOT IN GLOVE.

LOCKING DOORS ON RAIL CARS,PREPARING TO LOAD THEM,THE DOOR WAS BENT HE PUT ALL HIS WEIGHT ON THE RAIL BAR TO PRY IT UP TO THE LOCK,WHEN THE LOCK FELL INTO PLACE THE RAIL BAR SLIPPED AND HE FEL L ON THE OUTSIDE OF RIGHT FOOT.

WAS REPAIRING 992 LOADER, WHEN GETTING OFF MACHINE STEPPED FROM MACHINE TO GROUND AND TWISTED RIGHT ANKLE.

WALKING DOWN STEPS AT PRIMARY SAND PLANT SLIPPED ON THE CONCRET SLAB ALLEGEDLY SPRAINED LOWER MIDDLE LEFT SIDE OF HIS BACK

USING TORCH TO WELD OFF BUCKET LIP.HOT PEICE OF SLAG FELL,BURNED HOLE IN TROUSER LEG AND FELL INSIDE OF STEEL TOE BOOT.

WHILE PUTTING LID ON STEDMAN CRUSHER, HAD PRY BAR IN BOLT HOLE. HAD ARM HOLDING PRY BAR BETWEEN PRY BAR AND CRUSHER. WHEN LID WAS LOWERED BY A CRANE, PRY BAR WAS PUSHED BACK AND EMPLOYEE'S ARM AND WRIST CORNERED BETWEEN CRUSHER AND PRY BAR. WRIST WAS BROKEN.

WHILE POSITIONING A WEAR PLATE ON THE CUTTING TABLE HIS HAND SLIPPED PLATE CUT T IP OF THIRD FINGER OF RIGHT HAND TWO SUTURES REQUIRED

CUTTING BOLTS O3 A REPAIR LINK AND HIT THE BOLT WITH A CHIPPING HAMMER. A PIECE CAME OFF THE HAMMER AND STRUCK LEFT WRIST.

THE CARDBOARD T6BE STARTED COMING OUT OF THE GROUND, GRABBED FOR THE TUBE AND JUST THEN THE GROUND CAVED IN PUTTING PRESSURE ON TUBE WHICH SMASHED HAND AND FINGER AGAINST DRILL, CAUSING LACERA TION OF FINGER 5EFT HAND.

CARRYING GRATIN1 AT PRIMARY SAND PLANT STRAINED LOWER BACK.

PULLED PIN FROM3TOW BAR ON PORTABLE AIR COMPRESSOR TRUCK ROLLED BACK CAUSING TONGUE OF TOW BAR TO SWING AND COME DOWN ON LEFT FOOT ONE WHEEL WAS NOT BLOCKED CAUSING TRUCK TO ROLL

LOADED DRILL #33WITH BLASTING TUBES SECURING MAST TO DECK WHEN BLASTING TUBE SLID OFF TUBE ROCK ONTO LEFT HAND INDEX AND MIDDLE FINGER

LOOSENING BEARING CAP B OLT WITH A RATCHET AND SOCKET THE BOLT CAME LOOSE AND HE PINCHED R LITTLE FINGER BETWEEN RATCHET AND THE ELECTRIC MOTOR

TAPPING A RAKE BLADE OFF DOZER WITH A HAMMER TO LOOSEN IT, IT FELL ON LEFT FOOT. THREE FRACTURED BONES IN FOOT, AND ONE MISPLACED BONE.

GETTING IN CAR 5FTER WORK, FELT PAIN IN B ACK

WORKING ON TROMMEL WITH COMBO WRINCH, BACK STARTED HURTING AFTER HE GOT HOME.

REPLACING BOLTS IN STEDMAN CRUSHER IT WAS RAINING AND SLIPPERY HE LOST HIS FOOTING AND FELL ABOUT 7 FEET HE LANDED ON LEFT SIDE FRACTURED LEFT WRIST ABRASION TO UPPER LIP AND BRUISED LEFT LEG

DRILLING-DRILL CUT OFF AND PINCHED FINGER -HAD SURGERY.