Norcross Quarry: 1 muerte registrada Metal/Non-Metal

Operator was getting down from machine and lost footing on the next to top step and fell to the ground on their side and it tore a muscle in their leg and cracked a rib.

Employee was changing a head pulley bearing. After removing the turnbuckle EE was caught between the motor and frame.

Employee was repairing the weatherhead on CR4 motor and while removing the bolts with a drill the adapter caught in the bolt and twisted the drill quickly forcing the employee's hand into a piece of expanded metal motor shaft guarding causing a laceration on employee's hand.

Employee was digging in the muck pile when employee alleged that the seat belt hurt abdomen.

Employee alleged strained shoulder while descending a ladder.

On January 26, 2021 employee was moving steel from an overhead rack on the drill when EE felt shoulder pain. EE sought medical attention on March 1, 2021.  An MRI was performed on March 10, 2021 and EE was diagnosed with a rotator cuff tear.  EE will work full duty until EE's surgery date, March 19, 2021, which will then become a lost time incident.

Employee was cleaning a chute when EE was struck by a bar causing a laceration.

The employee sustained a finger injury while replacing feeder bottoms. The chain hoist wasn't secured when positioning the plate and came loose striking the employee's finger. The employee was taken to the hospital for medical treatment resulting in a broken finger/laceration.

On 8/3, EE was installing a guard for a grid coupling. As the guard was lifted, the lid fell back & the corner of the lid struck thumb causing a laceration. EE did not seek medical treatment at that time, but later advised the thumb was swollen, sore & EE was unable to bend it. EE was taken to medical facility on 8/6 where EE was treated for infection.

While the employee was changing the skirt on the transfer point between C-1 & C-2 conveyor, left hand made contact with the metal causing employee to receive a laceration to left index finger. The employee was wearing gloves at the time of the incident.

Employee slipped on catwalk steps and broke his right ankle.

Employee was welding on 7' mainframe on 7/18/2013 when he felt a pain in his right elbow. The pain progressively got worse and on 8/26/2013 he reported it to his supervisor and requested medical treatment.

Employees eyes were burnt while holding shims in place while another employee was welding.

At some time around 11:45 am - smoke was seen on our berm surrounding the property. The fire department was notified, the local MSHA field office was called as well as the 1-800-immediatly reporting line shortly when we realized the fire would not be extinguished within 30 minutes.

Employee was hammering a pin when a piece of metal punctured his left leg.

EE was climbing on the screen to tighten screen bolts, when his foot slipped and he fell to the same level, injuring his left knee.

EE received laceration to the back of the left hand caused by broken glass from picture frame.

Employee picked up rocks in roadway and pulled a muscle in his back.

Sudden movement causing strain to left shoulder.

Employee was found on platform to MCC Building at load out bins. Employees performed CPR until EMS arrived.

Injured worker was attempting to remove a tire from the 980G front end loader, when the tire slipped out of the tire holder and caught his right foot between the outrigger and the tire.

Supervisor/employee was loading screen tubes onto a boom truck with 2 other employees. The supervisor/employee caught his finger between one of the screen tubes and the boom truck.

Employee was changing out troughing guide roller set. Center moved and pinched his finger.

Employee was removing a can from an idler & broke thumb.

A mechanic and the injured employee were installing wear metal onto a loader bucket. The mechanic was tapping the adapter into place when a piece of metal hit the employee in the chin.

EMPLOYEE STRUCK HIS RIGHT KNEE AGAINST THE CONSOLE OF THE PIT LOADER WHILE TRAVELING ACROSS THE PIT FLOOR.

Employee was performing clean-up activities at #3 belt-lower surge tunnel. Abandoned water line-valve he was trying to load onto boom truck. The pipe swung around & smashed his little finger on right hand.

THE INJURED EMPLOYEE WAS STANDING AT THE RIGHT REAR OF A BOOM TRUCK WHEN THE OUTRIGGER WAS LOWERED DOWN ON HIS LEFT FOOT.

EE WAS WELDING BED LINER IN BED OF HAUL TRUCK. CLIP BROKE, CAUSING STEEL PLATE TO FALL ON EE'S FOOT.

The turbo failed on the pit loader resulting in a fire. The ee turned off the ignition, exited the cab and dropped from the midrail on the loader to the ground, approx 5 ft. a fire suppression system was on the loader and a fire extinguisher was located at the door also.

EE WAS CUTTING A CONVEYOR BELT, KNIFE SLIPPED AND CUT RIGHT THIGH.

EMPLOYEE WAS INJURED WHILE CHANGING WEAR METAL ON FRONT END LOADER. THE WEAR METAL SHIFTED AS THE EMPLOYEE WAS ATTEMPTING TO "KNOCK" IT INTO PLACE AND FELL ONTO THE EMPLOYEE'S FOOT.

EMPLOYEE WAS RETURNING WHEEL CHOCK TO STORAGE AREA ON HAUL TRUCK AND POSITIONED HER HAND BETWEEN THE FRAME OF TRUCK AND WHEEL CHOCK.

EE WAS INJURED WHILE MAKING REPAIRS TO A SHAKER USED TO TAKE QUALITY CONTROL SAMPLES. THE GUARD WAS RAISED TO ALLOW ACCESS TO SHAKER, GUARD FELL ON EE'S THUMB.

EE WAS PUSHING ON THE BASE OF A WELDER TO POSITION ON WELDING TRUCK. HE CAUGHT HIS LEFT INDEX FINGER BETWEEN TWO PIECES OF THE FRAME ON THE WELDER.

EE STRAINED HIS BACK WHILE OPERATING THE 992 C STRIPPING LOADER ON BECH #1. HE IS UNSURE OF THE EXACT TIME OF THE ACCIDENT. HE JARRED HURT BACK WHEN HE HIT HUMPS ON.

EMPLOYEE STATES: SETTING UP SHOT SERVICE DEVELOPED PAIN IN NECK SHOULDER AND JAW. FELL TO THE GROUND.

EE WAS WALKING ACROSS THE GROUND FROM THE WETBIN CONTROL HOUSE TO THE MOTOR CONTROL CENTER AND STEPPED OFF THE GRADED CURB AND SPRAINED HIS ANKLE.

EE WAS ASSISTING WITH BELT REPAIRS. A BELT WAS BEING PULLED BACK ONTO THE CONVEYOR FRAME. THE BELT CABLE GOT HUNG ON THE BELT SCRAPER SO THE INJ EE WENT UNDER THE DRIVE BELT GUARD & BEGAN PULLING ON THE VBELTS-ONCE HE PULLED ON THE BELTS THE CABLE THRU THE BELT SCRAPER & THE SHEAVE MOVED. THE EE'S HANDS WERE PULLED THRU THE SHEAVE.

EE WAS TRYING TO CONTROL THE FALL OF A WOODEN BLOCK & IT MASHED HIS RIGHT RING FINGERTIP. HE WAS BLOCKING THE FRAME OF THE LOADER WITH 8" X 8" X24" BLOCKS. FINGER WAS CUT & NEEDED 6 SUTURES.

EMPLOYEE WAS CHIPPING SLAG FROM A PIECE OF METAL 1 X 4 X 16 TO BE USED FOR FEEDER LINERS. SAFETY GLASSES WERE WORN, BUT SLAG WENT UNDER GLASSES.

EE WAS CUTTING OFF A BLASTING (CARDBOARD) TUBE WITH A POCKET KNIFE. KNIFE GOT HUNG IN CARDBOARD, EE GAVE A HARD PULL AND KNIFE WENT INTO HIS LEG (LEFT UPPER CALF).

EMPLOYEE WAS REMOVING BOLTS FROM ECCENTRIC DRIVE ON CRUSHER. THE EMPLOYEE WAS USING A 1" AIR WRENCH, HE WAS HOLDING THE SOCKET W/LEFT HAND; IT SLIPPED OFF RESULTING IN A CUT TO LEFT HAND BETWE EN THUMB AND INDEX FINGER.(3 STICHES TO HAND).

EMPLOYEE WAS OPERATING DRILL, HYDRAULIC HOSE TO COMPRESSOR CAME LOOSE FROM FITTING SPRAYING HYDRAULIC FLUID ON DRILL. THE HOSE CONTACTED THE COOLER FAN, GENERATING SPARKS WHICH CAUSED THE HYD FLUID TO BURN. FLAMES CAME INSIDE CAB AND BURNED DRILLER'S LEFT FOREARM AS HE WAS EXITING DRILL CAB.

EE WAS DESCENDING STAIRWAY OF CRUSHER RUN CONTROL TOWER; STATED HIS LEFT HAND SPASMED AND CAUSEDHIM TO FALL OVER THE HANDRAIL.

EE WAS USING HAMMER TO TRY & REMOVE FROZEN MATERIAL FROM CHUTE FEEDING CONVEYOR WHEN HAMMER SLIPPED & WAS CAUGHT BETWEEN ROLLER & SKIRT BOARD PLLLING THE EE'S LEFT HAND BETWEEN THE ROLLER & SK IRT BOARD. LEFT HAND WAS FRACTURED

EE WAS ATTEMPTING TO CHANGE DRILL BIT WHEN HIS MIDDLE FINGER ON HIS LEFT HAND WAS PINCHED BETWEEN THE DRILL BIT AND THE DRILL BIT CHECK. (REQUIRED STITCHES)

EMPLOYEE WAS LEAVING TRAINING ROOM IN FORD F150 PICKUP AND TURNED RIGHT OUT OF PARKING LOT AND WAS STRUCK BY CUSTOMER DUMP TRUCK.

EMPLOYEE WAS DESCENDING LADDER ON HAUL TRUCK AT THE END OF HIS SHIFT AND APPARENTLY TWISTED HIS ANKLE WHEN HE STEPPED DOWN. \

THE EMPLOYEE WAS REMOVING A PIECE OF 2" AIR PIPING FROM D.M. 45 INGERSOLL RAND DRILL. THE PIPINGWOULD NOT COME LOOSE SO THE EMPLOYEE SHOOK THE PIPING AND IT FELL APPROX 6 INCHES ON HIS SMALL FINGER, RIGHT HAND. FINGER WAS FRACTURED.

EMPLOYEE WAS SHARPENING A DRILL BIT WITH A GRINDING ROCK. A PIECE OF METAL FROM THE DRILL BIT EMBEDDED ITSELF INTO EMPLOYEES RIGHT EYE.

EE WAS INSERTING A BLASTING TUBE INTO DRILL HOLE WHEN HE LOST HIS FOOTING AND FELL FORWARD TO THE GROUND.

EE WAS UNLOADING A PALLET FROM A TRACTOR TRAILER WHEN THE LOAD SHIFTED AND THE EE S RIGHT THUMB WAS CUT BY THE BANDING AROUND THE PALLET.

EMPLOYEE FELL FROM HAUL TRUCK.

EE HIT LEFT DOOR OF CAB WITH LEFT ARM.

EE WAS REPLACING A BEARING AT THE HEAD PULLEY. A PORTAJACK WAS USED TO MOVE TO HEAD PULLEY OUTWARD SO THAT THE PRESSURE COULD BE RELEASED AND THE SEALS COULD BE PLACED INTO POSITION. THE PORTA JACK JUMPED OUT OF PLACE AND CAUGHT THE EE'S HAND BETWEEN THE SEAL AND BEARING HOUSING.

USING A 'DOGGING WEDGE' TO HOLD AR400 IN PLACE BEFORE WELDING. THE DOGGING WEDGE BROKE LOOSE & HIT EE'S THUMB. THE EE WAS TRYING TO GET THE AR4O0O CLOSER TO THE BOTTOM OF THE TRUCK BED BY HITT ING WEDGES INSIDE DOGGING WEDGE WITH SLEDGE HAMMER.

EE WAS REMOVING AN EMPTY OXYGEN CYLINDER FROM A PORTABLE CART & TRANSFERRING IT TO A HAND TRUCK.THE BASE OF THE CYLINDER SLIPPED CAUSING IT TO FALL ONTO HIS LEFT THUMB WHERE HE WAS HOLDING THE HAND TRUCK. HE RECEIVED 3 STITCHES.

AS 85 TON HUAL TRUCK BACKED INTO ANOTHER 85TON HAUL TRUCK PREPARING TO BACK TO A SHOVEL. THE BED OF THE FIRST TRUCK CRUSHED THE CAB OF THE SECOND TRUCK PINNING THE DRIVER. THE DRIVER SUSTAIN ED LACERATION TO HIS RIGHT LEG REQUIRING SEVERAL STITCHES.

WHILE WELDING IN A CHUTE UNDERNEATH NO. 1 SCREEN A PIECE OF SLAGG FELL INTO HIS BOOT, THROUGH HIS PANTS LEG.

DOZER WAS PUSHING DIRT OVER BERM A ROCK ROLLED BEHIND TRACK AS DOZER WAS BACKING UP AND THE TRACK HIT ROCK.

THE INJURED WAS INSTALLING A GRAVITY TAKE-UP PULLEY FRAME TO THE GRAVILTY GUIDE POLES WHEN HE STRAINED HIS LOWER BACK.

EE WAS TRAINING EE HOW TO OPERATE A CAT 41 68 BACKHOE EE WAS DEMOSTRATING ITS USE WHILE EE SAT ON THE CAR FENDER AS INSTRUCTED CONTACT WAS MADE WITH SOME WIRING CAUSING EE SHOULDER TO MAKE CON TACT WITH THE ROPS SUPPORT BAR

EMPLOYEE WAS COMPLETING HIS THIRD WEEK OF TRAINING TO OPERATE AN INGERSOLL RAND DM30 DRILL. THE STEEL HUNG UP IN THE HOLE AND IT BECAME HOT WITHEFFORT TO FREE. EE FORGOT THE STEEL WAS HOT AND HE BURNED HIS HAND WHEN HE PUSHED ON THE STEEL TO POSITION IT INTO THE RACK.

EE WAS COLLECTING BELT SAMPLES PLANT OPERATOR HAD SHUT DOWN PLANT & WENT TO FIND EE WHEN WAS TAKING UNUSUALLY LONG TIME FOUND EE LYING FACE DOWN AAT HOUSE OF 6FT STAIRWAY EE HAS NO RECOLLECTIO N OF FALL OR WHAT CAUSED FALL MATERIAL BUILDUP ON STGEPS WAS PRESENT

SEE ATTACHED CONTUSIONS TO NECK & SHOULDER ALLEGED.

EE WAS TIGHTENING BOLTS ON SIDE FRAME OF 95 NW DROPBALL HE WAS USING A 1IN DRIVE RATCHET WITH A 1 1/2IN SOCKET THE SOCKET SLIPPED OFF THE BOLT HEAD THE MOVEMENT OF PUSHING THE RATCHET CARRIED HIS HAND INTO THE SIDE FRAME BEHIND THE BOLT CUTTING HIS FINGER TIP

EMPLOYEE WAS TRYING TO REMOVE THE BUSHING FROM INSIDE THE SHIFTING BRACKET OF A 769 CAT HAUL TRUCK THE BRACKET WAS POSITIONED IN A VISE THE EMPLOYEE WAS HOLDING THE PIN WITH HIS LEFT HAND & ST RIKING THE PIN WITH A BALL PEEN HAMMER EMPLOYEE MISSED THE PIN & STRUCK HIS FINGER CUTTING IT

EE AND FOREMAN HAD OPENED COMPARTMENTS BEHIND OPERATOR CAB TO CHECK FOR BLOWN HYD LINE FOUND LINE AND DETERMINED WHAT TOOLS NEEDED AND AS FOREMAN WAS LEAVING TO GATHER TOOLS EE WALKED ACROSS C OMPARTMENT AREA AND STEPPED OFF INTO OPEN COMPARTMENT AREA.

EMPLOYEES WERE ADDING COOLANT TO THE 85 TON HAUL TRUCKS USING A 5 GALLON PLASTER BUCKET. EMPLOYEE WAS UP ON TOP OF THE ENGINE COMPARTMENT AND ANOTHER ON THE GROUND. EMPLOYEE DROPPED DOWN THE 5 GALLON BUCKET TO OTHER APPROX 2 FT. IN ATTEMPT TO CATCH THE BUCKET THE REMAINING FLUID (APPROX 1 GALLON) SHIFTED AND CAUSED THE BUCKET TO HIT HIM ON THE UPPER LIP AND FRONT UPPER TEETH.

SHARPENING BITS WITH 4 INCH GRINDING DISC ON 1/4 INCH HIGH SPEED DIE GRINDER. THE DISK BROKE AND A PIECE WENT INTO THE LEFT KNEE-RESULTING IN LACERATION AND CONTUSION.

HE WAS HELPING PLANT REPAIRMAN TAKE SPEED REDUCER APART. HE WAS HOLDING THE NUT WITH A BOX END WRENCH WHILE REPAIRMAN WAS TRYING TO LOOSEN BOLT. THE BOLT TURNED AND IT PULLED HIS HAND AND WREN CH UP AGAINST HOUSING.

THE EE WAS DISASSEMBLING A 90 DEGREE ELBOW FROM A 10 INCH PIPE THE PIPE ROLLED OFF THE 1 FTX 1 DFT X 2 FT BLOCK AND HIT EE S LEFT FOOT.

HE WAS WASHING OUT UNDER THE #1 TOWER AND SOME SMALL ROCK FELL AND HIT HIM ON THE BACK OF THE NECK.

THE EMPLOYEE WAS JARRED WHEN A LARGE ROCK WAS LOADED ON HIS TRUCK.

THE GREASE BRUSH WAS FROZEN INSIDE OF THE GREASE BUCKET SO THE EMPLOYEE WAS CUTTING THE TOP OF THE PLASTIC BUCKET WITH HIS POCKET KNIFE. THE KNIFE SLIPPED AND CUT HIS LEFT THUMB.

MECHANIC WAS WORKING ON A GRILL OF HAUL TRUCK THE GUARD DROPPED DOWN WHEN HE REMOVED THE BOLTS & IT CAUGHT HIS FINGER BETWEEN THE GUARD & THE BUMPER OF THE TRUCK

EMPL WAS DISLODGIN ROCK BETWEEN FEED HOPPER & BOWL HOPPER WHEN ROCK WAS KNOCKED OUT FEED HOPPER MOVED & CAUGHT THUMB ON CLIP & CRUSHED IT. STITCHES WERE REQUIRED.

I,NAME WAS STANDING IN PRIMARY WHILE CONCAVES WERE BEING BROKEN LOOSEN WITH JACK HAMMER. A PIECE OF STEEL FROM THE HAMMER POINT HIT HIM AND IMBEDDED IN THE UNDERSIDE OF HIS CHIN-HE WAS TAKEN T O SHALLOWFORD HOSPITAL FOR TREATMENT.

HE HAD BEEN CLEANING WALKWAY AT AUXILIARY PLANT HE HAD KNELT DOWN & WHEN HE STRAIGHTENED BACK UP HE PULLED MUSCLE IN BACK. MEDICATION FOR PAIN WAS PRESCRIBED AT CLINIC.

SHE WAS HELPING TO UNSTOP CHUTE WHEN A ROCK SLID DOWN ON HER ARM. THE JAGGED EDGE OF THE STONE CUT HER RIGHT FOREARM.

EMPLOYEE WAS PULLING HIMSELF UP ONTO BED OF SERVICE TRUCK-HE SLIPPED AND WHEN HE CAUGHT HIMSELF HE PULLED A STOMACH MUSCLE.

DRIVER BACKED INTO THE FRONT RIGHT LEG AT THE PRIMARY CRUSHED WITH DRIVERS SIDE OF HAUL TRUCK. **MEDICATION REPORTED TO US. TODAY'S DATE 9/8/89 D.NAME GWINNETT MEDICAL CLINIC

DRIVING WATER TRUCK ON RAMP AT PRIMARY TRUCK JUMPED OUT OF GEAR & ATTEMPTS GTO BRAKE DID NOT SLOW IT DOWN. DRIVER JUMPED FROM TRUCK TRUCK THEN HIT PARKED WELDING TRUCK FORCING IT INTO BOOM TRU CK WHICH IN TURN STRUCK ROCK.

EMPLOYEE HADN WAS CAUGHT BETWEEN A LARGE ROCK AND SIDE FRAME OF CONVEYOR WHILE ATTEMPTING TO MOVE THE ROCK FROM THE INSIDE OF CONVEYOR BELRT NEAR HEADPULLEY TO THE TOP SIDE OF CONVEYOR BELT.

HOLDING METAL BRACKET WHILE OTHER EMPLOYEE WAS CUTTING THE BRACKET OFF. HE INADVERTENTLY MOVED TORCH ACROSS HIS HAND BURNING IT.

EMPL WAS TRIMMMING CHUTE LINERS WITH A UTILITY KNIFE IN A DIRECTION AWAY FROM CHEST TOWARD LEG HIS HAND SLIPPED AND THE KNIFE LACERTED SKIN BELOW R KNEE REQUIRED 4 STITCHES

STARTED TO CLIMB UP ON DRILL LOST HIS FOOTING AND FELL TO THE GROUND.

EMPLOYEE WAS UNDER SHOVEL IN CAR BODY HOLDING LEFT SWING TRANSMISSION BOLT WHILE ON HIS BACK WITH HIS FEET PROPPED UP. HIS FEET SLIPPED WHILE REACHING FOR BOLT.

WALKING DOWN SHORT FLIGHT OF STEPS AND SLIPPED AND CAUGHT WITH ARM. HURT SHOULDERS AND BACK.

MAN GOT OFF LADDER AND STEPPED ON BLOCK OF WOOD FALLING ON LEFT KNEE AND BACK.

WHILE H OLDING TAPE MEASURE IN PLACE EMPLOYEE LEANED ON UNSTALE METAL ANGLE AGTAINST HIS BACK METAL ANGLE GAVE WAY & EMPLOYEE FELL BACKWARD BINDING HIS HAND & FOREARM BETWEEN TWO METAL BARS

EMPLOYEE WAS ATTEMPTING TO UNCHOKE FEED CHUTE WHEN FEED MATERIAL FELL LOOSE KNOCKING EMPLOYEE OFF PLATFORM ONTO WALKWAY BELOW.

HE WAS TRYING TO ET #1 BELT TO ROLL BACK HE HAD A BAR IN TAIL PULLEY WHEN IT SLIPPED IT CAUGHT HIM IN BETWEEN 2 BEAMS UNDER HIS ARMS CAUSING A STRAIN ON RT.SHOULDER

MAN HOOKED A CHAIN TO THE MIDDLE OF CROWD TRANSMISSION AS THE CRANE PICKED IT UP THE TRANSMISSION FLIPPED OVER AND CUT HIS LEFT FOREARM.

MAN WAS CUTTING A TUB AND THE KNIFE SLIPPED AND CUT RIGHT LEG.

EMPLOYEE REPORTED INJURY TO FOREMAN DID NOT MAKE REPORT BUT REMEMBERED EMPLOYEE TELLING HIM.EMPLOYEE HAD DEVELOPED PROBLEMS AND WENT TO DOCTOR.NEITHER REMEMBER WHAT HAPPENED WHEN OR WITH WHAT T THEY WERE WORKING.

CUTTING METAL A3D PIECE OF SLAG BURNED RT EYE

LIFTING MOTOR B5SE AND STRAINED BACK.

STANDING ON ANG5E.

2 EMPLOYEES WER9 REMOVING A GUARD FROM A SCREEN WHEN THE GUARD WAS SET DOWN 1 EMPLOYEES FINGER WAS CAUGHT AND THE NAIL TORN OFF

HE WAS HOLDING 1IN HAMMER WHILE OTHER MAN HIT IT WITH ANOTHER HAMMER,HAMMER CHIPPED OFF FAND WENT IN HIS ARM.

HE WAS ATTEMPTI3G TO FLIP #6 LID ON #4 TOWER,ROCK HAD THE LID WEDGED,HE WAS JERKING ON HANDLE TO FREE LID WHEN CAME LOOSE AND FLIPPED CATCHING HIS RIGHT HAND BETWEEN CLIP AND LID CUTTING HIS H AND AT THUMB AN8 WRIST. (STITCHES).

EMPLOYEE WAS CL2SING COWLING DOOR ON AIR COMPRESSOR.HINGE ON CENTER SECTION OF DOOR RELEASED SUDDENLY AND MASHED FINGER BETWEEN DOOR SECTIONS.

ATTEMPTING TO D3SLOADGE STUCK MATERIAL FROM AN MATERIAL BIN. HE WAS USING PRY BAR AND IT SLIPPED AND SMASHED HIS INDEX FINGER.

CHANGING TEETH 2N SHOVEL KEEPER PIN OUT WITH A PIN HAMMER PIECE OF METAL FLEW OFF & PUNCTURED RIGHT HAND. INFECTION & STITCHES.

EE FELL FROM BA7K OF WELDING TRUCK WHILE RIDING TO TIME CLOCK AT END OF SHIFT. EE STRUCK LEFT SIDE OF HEAD CUASING LACERATION TO HIS LEFT EAR REQUIRING STITCHES.

I.NAME AND I.NA4E WERE CHANGING SHANKS ON THE 988B BUCKET I.NAME WAS HAMMERING OUT PINS FROM BUCKET WHEN A PIECE OF METAL FLEW OFF THE HAMMER AND HIT I.NAME IN THE FOREHEAD IT REQUIRED AN INCI SION TO REMOVE 7HE 1/4 IN PIECE OF METAL AND 2 STITCHES TO CLOSE THE WOUND

CHANGING BIT, H2OKED UP FIRST WRENCH AND STEEL ROTATED AND CHAIN LOCKED DOWN GRABBING END OF FINGER. CUT END OF LITTLE FINGER/N LEFT HAND.

MAN JUMPED OFF 6ACK OF PIT TRUCK THERE WAS A BOLT STICKING OUT ON BACK OF TRUCK HIS RT LEG CAUGHT BOLT AND CUT LEG

I,NAME WAS USIN1 A HAMMER TO TAP CONCAVE LOOSE ANDA PIECE OF THE METAL CHIPPED OFF AND HIT HIS LEFT FOREARM CAUSING A PUNCTURE WOUND, METAL WAS REMOVED AND 3 STITCHES TAKEN.

I.NAME JUMPED FROM CAB OF TRUCK.TRUCK WAS DUMPING AT PRIMARY CRUSHER.SEAL ON HOIST CYLINDER BLEW,SPRAYING OIL ON EXHAUST AND CAUSING SMALL FIRE.AUTO FIRE SUPRESSION SYSTEM ACTIVATED.EMPL JUMPE D FROM TRUCK.

SLIPPED ON ROCKS AND FELL - BACK STRAIN

PUTTING SEAL IN A WHEEL,PUSHING SEAL RING IN PLACE AND HAND SLIPPED CUTTING HAND STITCHES WERE REQ.

CUT TO LEFT HAND REQUIRING STITCHES EMPLOYEE WAS LOADING WELDING RODS ON TO THE TRUCK AND THE METAL BOX THAT THE RODS ARE KEPT IN SLIPPED AND CUT HIS HAND

MAN WAS CLIMBING STEPS TO GET IN TRUCK GOING UP THE LADDER TO S ECOND STEP. THE BOTTOM CHAIN SSTEP FLIPPED UP CAUSING MAN TO LOSE BALANCE & FALL ON BUMPER CUTTING HIS LEG.

HE WAS POKING AT THE FIRE AND IT BLEW OUT ON HIS RIGHT HAND AND RIGHT SIDE OF FACE.

CLEANING UP AND REMOVED CABLE FROM MUCK PILE,PIECE OF CABLE STUCK IN RING FINGER ON RIGHT HAND.

PUTTING GEAR IN DRAGLINE WITH BOOM TRUCK, RIGGING UP CABLE AND A PIECE OF CABLE WENT IN RIGHT INDEX FINGER

CHANGING SCREENS & BROKE THUMB ON RIGHT HAND.

WORKING IN BUCKET OF BOOM TRUCK REPAIRING #2 SHOVEL WHEN BUCKET FASTENER BROKE AND MAN FELL WITH BUCKET CAUSING CUTS ON HEAD

MAN PICKED UP ROCK OFF CONVEYOR BELT AND ANOTHER ROCK FELL ON RIGHT HAND MASHING RIGHT HAND RING FINGER.

STANDING BY WARMING FIRE, PANTS WERE GREASY AND THEY CAUGHT ON FIRE BURNING LEFT LEG.

JACK BOLT PULLED OUT AND HIT EMPL IN CHEST.LEFT SIDE OF CHEST-CONTUSION.

EMP WAS SEVICING A LOADER WHEN HE SLIPPED ON SOME GREASE AND FELL HE LANDED WITH HIS BACK AGAINST THE BUCKET ARMS AND THEN FELL FROM THE LOADER TO THE GROUND