HAVERSTRAW QUARRY & MILL Metal/Non-Metal

While walking to the long reach excavator, employee twisted knee while stepping through ruts in the frozen mud. EE feels some discomfort but refused medical attention at this time. Miner went to EE's doctors on 1/8/2025 and was prescribed physical therapy. No restrictions/ no time lost.

Employee was shoveling overhead onto a conveyor belt. This resulted in discomfort in EE's left shoulder. Employee claims they did not feel the discomfort towards the middle to the end of their shift. After getting an MRI, a tear was revealed in EE's labrum. Employee continued to work until the scheduled surgery on 12/20/2023.

Miners noticed smoke coming from Tower 6 in the secondary. 911 was called and was able to contain the fire from reaching other towers. There were no injuries but substantial loss to equipment.

At about 11:25pm a 2nd shift employee was welding on an arm guard to the primary crusher when EE felt an electric shock in elbow. EE asked the fire watch to turn off the welding machine and found that the leads had worn through grounding to the primary head causing the arc. The employee was brought to the hospital as a precaution and was given prescription medication.

Around 2pm a CSX freight train caused fires in the surrounding areas along the tracks due to a locked up wheel. Around 6:10pm the fires made their way to mine property. No injuries or major damage occurred on mine property but the brush fire burned semi controlled for longer than 30 minutes. MSHA was called at 6:34pm.

Employee was installing cylinders on the primary grapple when they hit their thumb with a hammer. After a week of the small cut not healing they went to a doctor on 3/15/2023 where they were given ointment as a precaution for infection. No restrictions.

While being loaded by an excavator with shot rock, the employee says a rock hit the inner side wall of the dump body causing EE to shift in the seat and hit the inside of the door. Employee was wearing the seatbelt. Employee has pain in their shoulder.

While working in the C39 tunnel the employee rolled left ankle slightly. When the employee's ankle rolled it caused a small fracture in the 5th metatarsal.

While working at Tilcon NY Haverstraw Quarry, employee was fusing pipe and pinched right hand middle & ring fingers resulting in injury to nail area of middle finger & tip of ring finger. Injured party taken to hospital by ambulance.

while using hydraulic torque wrench to tighten eccentric bolts on the primary crusher, the wrench came loose when pressurized. As employee attempted to hold/control the wrench, their right shoulder was extended causing a strained bicep.

Industrial hearing report dated 2/22/18, received priority mail 2/26/18, states: persistent threshold shift as outlined by MSHA/OSHA and must remain on MSHA log. Original hearing threshold shift: 3/20/2017

Foreman went to hand a 2x10x10 wood plank to use for belt splice and stepped in mud and felt pain in right knee. Initially thought it was arthritis but an MRI revealed a meniscal tear in Dec.

Employee assisting with flipping a conveyor belt troughing roller and the roller struck his right hand middle finger tip causing a fracture and also required stitches. He returned back to work same day and able to resume work.

Employee was working with other employee holding a 1/2"x6"x42" plate to be welded to a structure. Other employee placed tack weld and released hold. Weld did not hold and injured employee was left holding weight, felt pain in right arm. Initially no findings until 2/11/13 when it was discovered he had torn bicep. Employee has been working since day of incident.

When closing engine hood on Hitachi Excavator 450EX employee closed hood on left hand finger tip causing laceration

While removing the race from a bearing on a conveyor, injured employee was holding a punch while other employee striking with hammer when hammer slipped and struck right pinky finger resulting in laceration.

Employee went to his supervisor after fueling his equipment and told him that he did not feel well. An ambulance was called for a suspected heart attack.

Employee's leg became stuck in skid steer bucket causing him to fall. He received an injury to his shoulder and was released back to work with no lost days. The pain continued and the employee was scheduled for surgery on 5/6/2009.

Employee was in manlift working at sand plant cutting conveyor belt with knife. While employee was cutting, the belt shifted, causing employee to slip. This caused the knife to strike the employee's hand and cut through the glove.

Operating drill press to fabricate a cover from sheet metal, the metal sheet began spinning and cut through gloved hand.

Replacing belt on motor and blower. Employee was rotating belt onto sheave when his gloved hand was caught and pinched by the sheave.

Lifting a speed reducer with an electric hoist, employee's finger was pinched between the hand rails.

Attempting to connect a welding unit to a truck, the employee felt a strain in his lower back.

Employee was doing repair on an idler at head pulley when the belt moved, causing employee's hand to become lodged. (Stitches left little fingertip; possible fracture.)

Employee was crushed between a screen deck and a hood.

While investigating why a circuit breaker would not reset, the cover was taken off and the employee tried to reset it. A short circuit occured and an electrical arc caused injury to 3 employees of Allbright Electric

While investigating why a circuit breaker would not reset, the cover was taken off and the employee tried to reset it. A short circuit occured and an electrical arc caused injury to 3 employees of Allbright Electric

While investigating why a circuit breaker would not reset, the cover was taken off and the employee tried to reset it. A short circuit occured and an electrical arc caused injury to 3 employees of Allbright Electric

Employee was walking behind another employee when he tripped, striking his leg on the crusher platform.

Ee was standing on a platform at the dock when the dock gave way and he landed in the water.

emp twisted knee stepping off ladder employee became a lost time as of 12/15/2004 when he had surgery for his knee.

EMPLOYEE WAS USING A UTILITY KNIFE TO OPEN A GREASE BARREL WHEN HIS HAND SLIPPED AND HE CUT HIS L PINKY FINGER WITH THE KNIFE.

RIGHT HAND PINNED BETWEEN STEEL PLATE AND RAILING WHILE REMOVING SECTION PREVIOUSLY CUT.

EMPLOYEE WAS LIFTING A HIGH TORK TO MOVE IT, TRIPPED, FELT PULL IN GROIN AREA.

WHILE WORKING ON DANGED CONVEYOR BELT, LOCKING CLAMP HOLDING BELT SECURE SLIPPED AND CAUSED INJURY TO EE S LOWER BACK.

ELECTRIC LACERATION RIGHT HAND RING FINGER.

EMPLOYEE TRIPPED WHILE WALKING DOWN STAIRS.

COUNTERWEIGHT HIT LEFT FOOT.

EE STEPPED OFF CURB OUTSIDE OF DAYROOM TWISTED R ANKLE.

EMPLOYEE WAS CLIMBING OFF A 992 LOADER ONTO THE FUEL DOCK. HE SLIPPED WHILE STEPPING ON RAILING.

WHILE, EE WAS EXITING BOBCAT STEPPED DURING AND TWISTED RIGHT ANKLE ON ROCK.

WHILE CHANGING SREENS IN SECONDARY PLANT, HE WASSWINGING A HAMMER TO DRIVE CENTER PIN TO LINE UPHOLDS AND HIT END OF FINGER ON RIGHT HAND.

EE WAS GUIDING A STEEL PLATE INTO A CHUTE WITH HIS LEFT LEG WHEN HE FELT A SHARP PAIN IN LEFT KNEE.