Avísenme cuando se presente un nuevo incidente de la MSHA en Butner Quarry.
| Trimestre | Horas trabajadas | Citaciones | S&S | Por 1M hrs |
|---|---|---|---|---|
| 2025 Q4 | 38,302 | 0 | 0 | 0.0 |
| 2025 Q3 | 35,917 | 0 | 0 | 0.0 |
| 2025 Q2 | 32,321 | 0 | 0 | 0.0 |
| 2025 Q1 | 36,307 | 1 | 0 | 27.5 |
| 2024 Q4 | 30,892 | 0 | 0 | 0.0 |
| 2024 Q3 | 30,371 | 5 | 0 | 164.6 |
| 2024 Q2 | 28,600 | 0 | 0 | 0.0 |
| 2024 Q1 | 30,554 | 3 | 0 | 98.2 |
EE was removing large rock from catwalk and smashed finger between handrail and rock. The EE was wearing gloves.
Tech was working on installing new piece of glass, when they were pulling they hit their front tooth and knocked it out
Employee was carrying cutting edge and tripped causing a laceration to the palm of the left hand that required three sutures.
Miner was closing a leaking water ball valve when the valve assembly disconnected from the mount striking the miner in the forehead.
Employee was walking under a conveyor when a rock fell from the conveyor striking EE above EE's upper lip. Ee was wearing hard hat and eye protection.
Employee was changing a return roller on conveyor 2 when EE injured EE's left pinky finger. EE was wearing gloves at the time of injury.
The employee was leaving EE's desk when EE struck the corner of an open desk drawer with EE's leg
Employee was operating 772 haul truck and the employee smashed middle and ring finger on right hand between the frame and the seat.
Ee was lifting toggle rods above head when ee felt a pain in right shoulder. EE was placed on restricted duty.
Employee was hitting a striking wrench with a 2 pound sledge hammer and inadvertently hit left hand thumb.
Miner was performing routine maintenance on a conveyor to remove gear reducer. Miner sprained right ring finger while doing so.
Cut right hand ring finger while exiting corrugated metal building.
Lost balance after lifting 55lbs of flocculant. Injured back.
Employee injured back trying to turn bucket wheel with the assistance of other employees during bucket wheel installation. Accident was not reported until 5/7/13.
Ee was removing pin on 972G loader. The bucket and link were removed. Ee was pulling pin out of the top z-bar link where it attaches to the tilt cylinder. Ee pulled pin out and the z-bar shifted because pin was slightly over center. The Ee's thumb was caught between the head of the pin and the bucket leveler bracket.
Ee lost footing while installing j-bolt on screen. Ee slipped scraping his right shin and hit his right hip on 2" channel piece of channel.
EE was assisting in removing pin from a Caterpillar 944 bucket when the pin came out unexpectedly and crushed left hand index finger between pin and bucket.
Ee was pulling on water hose to wash off concrete pad when he stated he felt his wrist pop and noticed pain.
Employees left foot slipped from walkway platform to step causing shin to contact step. Conditions: flat walkway with one step up to another level.
Ee was using sledge hammer on plate to press large bushing into loader (equipment) link. A small piece of metal came off of plate and punctured Ee's left forearm.
Employee lacerated his thigh with a power tool while cutting screen cloth. Injury required five stitches and medication for infection.
Employee sprained ankle on unstable ground (loose gravel) while walking down stairs at scale house.
Employee was turning over the cutting edge of a 972G CAT loader. As he was loosening the right nut/bolt of the cutting edge the center bolt broke free causing the edge to drop suddenly to the ground on his right foot.
Bolt was being knocked from pin on EC 240 LR Excavator. A punch was struck by another employee to remove pin when the working end of punch broke off and hit employee in the neck.
The injured miner was dismounting a haul truck when he slipped and started to fall. As he was falling he was able to regain his grip with his left hand and the weight of his body caused him to strain his left shoulder.
Employee was removing parking brake assembly from heavy equipment when the parking brake assembly shifted and pinched the right ring finger between the parking brake and the frame of the machine.
The injured miner failed to maintain three points of contact and slipped while climbing the ladder of an intregated tool carrier and the tailbone of his lower back contacted the machine. He reported this accident on the following day and refused medical treatment. Medical attention was requested on 3/14/07.
The affected miner had been welding on guards during his shift and had gone home at the end of his shift. Soon after arriving home, both of his eyes started to hurt and swell closed. He sought immediate medical attention and was diagnosed as having welding flash.
The injured miner was throwing rock from a conveyor at the end of his shift and on his way home felt a strain in the area of his left lower back. This was not reported until the morning of 03/14/06.
The injured employee was checking the shims in the toggle block section of the jaw crusher at the primary side of the plant. He began to climb back down after checking the shims and slipped on a step on the front of the jaw crusher mainframe that had a small spot of oil on it. Due to losing his footing, he fell down to the platform below and injured his back.
The injured miner was attempting to remove a bearing cap bolt while performing maintenance on a jaw crusher with a sledge hammer and another hammer used for driving out pins. As he struck the pin-driving hammer with the sledge hammer trying to drive out the cap bolt, a small piece of the pin-driving hammer broke off an became embedded into the calf muscle on his left leg.
EE was assigned the task to dispense diesel fuel into a bulldozer. EE noticed a rock that was hindering him from getting close enough for the fuel nozzle to reach the dozer. EE attempted to move the rock with the help of coworker. EE strained a muscle on the right side of his lower back.
The employee injured his back moving furniture outside of work back in early March. He was cleared to return to work on March 21, 2004. After two weeks (April 7, 2004) he aggrevated the same area in his lower back while he lifted a piece of metal plate onto a conveyor belt (C-5).
EE WAS CUTTING USING A TORCH. HOT SPARKS FLEW ONTO HIS LEFT HAND GLOVE, CATCHING IT ON FIRE.
EE WAS ASSISTING A WELDER. HE WAS TOLD NOT TO LOOK AT THE WELDING ROD, BUT DID SO ANYWAY. HE DID NOT HAVE WELDING GOGGLES ON. HE SUSTAINED MINOR FLASH BURN TO HIS EYE.
EE WAS LIFTING A PIECE OF METAL AT THE SECONDARY. WHEN HE LIFTED THE METAL AND TURNED HE FELT A SHARP PAIN IN HIS LOWER BACK.
EE WAS DISMOUNTING CONVEYOR #8 ONTHE SECONDARY PLANT. HE STEPPED ON AN 8'-10' ROCK & FRACTURED HIS RIGHT ANKLE. HE WAS USING A LADDER TO GET ON& OFF THE CONVEYOR
EE WAS CHECKING THE HYDRAULICS ON THE OMNICONE CRUSHER. HE HAD DISCONNECTED THE LINER & INSTALLED PLUGS TO LOOK FOR ANY LOST PREWSSURE. ON ONE LINE, AS HE REMOVED THE PLUG, HYDRAULIC FLUID SHO T OUT * ONTO EE. HE JUMPED OUT FO THE WAY, STRIKING HIS HAND ON THE CRUSHER CAUSING A SPRAIN & BRUISE TO THE LEFT WRIST.
EMPLOYEE LOST HIS FOOTING ON THE STAIRS WHILE WALKING DOWN FROM #2 SCREEN. HE CAUGHT HIMSELF ON HIS WRIST, RESULTING IN A SPRAIN TO HIS RIGHT WRIST.
EMPLOYEE WAS DISMOUNTING THE TRUCK WHILE PARKED AT THE DUMP HOPPER. AS HE STEPPED ONTO THE GROUND, HE FELL BACKWARDS CATCHING HIMSELF WITH HIS LEFT ARM.
ON 6/27, EE REPORTED TO HIS SUPERVISOR THAT HIS BACK WAS SORE AND HE NEEDED A COUPLE TYLENOL. HE SAID THE 40 TON TEREX HE WAS OPERATING RODE ROUGHER THAN THE CAT 777 HE NORMALLY OPERATED. HE F INISHED THE SHIFT AND WORKED 6/28 WITHOUT INCIDENT. HE REPORTED THE INJURY ON FRIDAY 6/30.