Butner Quarry Metal/Non-Metal

Employee was carrying cutting edge and tripped causing a laceration to the palm of the left hand that required three sutures.

Miner was closing a leaking water ball valve when the valve assembly disconnected from the mount striking the miner in the forehead.

Employee was walking under a conveyor when a rock fell from the conveyor striking EE above EE's upper lip. Ee was wearing hard hat and eye protection.

Employee was changing a return roller on conveyor 2 when EE injured EE's left pinky finger. EE was wearing gloves at the time of injury.

The employee was leaving EE's desk when EE struck the corner of an open desk drawer with EE's leg

Employee was operating 772 haul truck and the employee smashed middle and ring finger on right hand between the frame and the seat.

Ee was lifting toggle rods above head when ee felt a pain in right shoulder. EE was placed on restricted duty.

Employee was hitting a striking wrench with a 2 pound sledge hammer and inadvertently hit left hand thumb.

Miner was performing routine maintenance on a conveyor to remove gear reducer. Miner sprained right ring finger while doing so.

Cut right hand ring finger while exiting corrugated metal building.

Lost balance after lifting 55lbs of flocculant. Injured back.

Employee injured back trying to turn bucket wheel with the assistance of other employees during bucket wheel installation. Accident was not reported until 5/7/13.

Ee was removing pin on 972G loader. The bucket and link were removed. Ee was pulling pin out of the top z-bar link where it attaches to the tilt cylinder. Ee pulled pin out and the z-bar shifted because pin was slightly over center. The Ee's thumb was caught between the head of the pin and the bucket leveler bracket.

Ee lost footing while installing j-bolt on screen. Ee slipped scraping his right shin and hit his right hip on 2" channel piece of channel.

EE was assisting in removing pin from a Caterpillar 944 bucket when the pin came out unexpectedly and crushed left hand index finger between pin and bucket.

Ee was pulling on water hose to wash off concrete pad when he stated he felt his wrist pop and noticed pain.

Employees left foot slipped from walkway platform to step causing shin to contact step. Conditions: flat walkway with one step up to another level.

Ee was using sledge hammer on plate to press large bushing into loader (equipment) link. A small piece of metal came off of plate and punctured Ee's left forearm.

Employee lacerated his thigh with a power tool while cutting screen cloth. Injury required five stitches and medication for infection.

Employee sprained ankle on unstable ground (loose gravel) while walking down stairs at scale house.

Employee was turning over the cutting edge of a 972G CAT loader. As he was loosening the right nut/bolt of the cutting edge the center bolt broke free causing the edge to drop suddenly to the ground on his right foot.

Bolt was being knocked from pin on EC 240 LR Excavator. A punch was struck by another employee to remove pin when the working end of punch broke off and hit employee in the neck.

The injured miner was dismounting a haul truck when he slipped and started to fall. As he was falling he was able to regain his grip with his left hand and the weight of his body caused him to strain his left shoulder.

Employee was removing parking brake assembly from heavy equipment when the parking brake assembly shifted and pinched the right ring finger between the parking brake and the frame of the machine.

The injured miner failed to maintain three points of contact and slipped while climbing the ladder of an intregated tool carrier and the tailbone of his lower back contacted the machine. He reported this accident on the following day and refused medical treatment. Medical attention was requested on 3/14/07.

The affected miner had been welding on guards during his shift and had gone home at the end of his shift. Soon after arriving home, both of his eyes started to hurt and swell closed. He sought immediate medical attention and was diagnosed as having welding flash.

The injured miner was throwing rock from a conveyor at the end of his shift and on his way home felt a strain in the area of his left lower back. This was not reported until the morning of 03/14/06.

The injured employee was checking the shims in the toggle block section of the jaw crusher at the primary side of the plant. He began to climb back down after checking the shims and slipped on a step on the front of the jaw crusher mainframe that had a small spot of oil on it. Due to losing his footing, he fell down to the platform below and injured his back.

The injured miner was attempting to remove a bearing cap bolt while performing maintenance on a jaw crusher with a sledge hammer and another hammer used for driving out pins. As he struck the pin-driving hammer with the sledge hammer trying to drive out the cap bolt, a small piece of the pin-driving hammer broke off an became embedded into the calf muscle on his left leg.

EE was assigned the task to dispense diesel fuel into a bulldozer. EE noticed a rock that was hindering him from getting close enough for the fuel nozzle to reach the dozer. EE attempted to move the rock with the help of coworker. EE strained a muscle on the right side of his lower back.

The employee injured his back moving furniture outside of work back in early March. He was cleared to return to work on March 21, 2004. After two weeks (April 7, 2004) he aggrevated the same area in his lower back while he lifted a piece of metal plate onto a conveyor belt (C-5).

EE WAS CUTTING USING A TORCH. HOT SPARKS FLEW ONTO HIS LEFT HAND GLOVE, CATCHING IT ON FIRE.

EE WAS ASSISTING A WELDER. HE WAS TOLD NOT TO LOOK AT THE WELDING ROD, BUT DID SO ANYWAY. HE DID NOT HAVE WELDING GOGGLES ON. HE SUSTAINED MINOR FLASH BURN TO HIS EYE.

EE WAS LIFTING A PIECE OF METAL AT THE SECONDARY. WHEN HE LIFTED THE METAL AND TURNED HE FELT A SHARP PAIN IN HIS LOWER BACK.

EE WAS DISMOUNTING CONVEYOR #8 ONTHE SECONDARY PLANT. HE STEPPED ON AN 8'-10' ROCK & FRACTURED HIS RIGHT ANKLE. HE WAS USING A LADDER TO GET ON& OFF THE CONVEYOR

EE WAS CHECKING THE HYDRAULICS ON THE OMNICONE CRUSHER. HE HAD DISCONNECTED THE LINER & INSTALLED PLUGS TO LOOK FOR ANY LOST PREWSSURE. ON ONE LINE, AS HE REMOVED THE PLUG, HYDRAULIC FLUID SHO T OUT * ONTO EE. HE JUMPED OUT FO THE WAY, STRIKING HIS HAND ON THE CRUSHER CAUSING A SPRAIN & BRUISE TO THE LEFT WRIST.

EMPLOYEE LOST HIS FOOTING ON THE STAIRS WHILE WALKING DOWN FROM #2 SCREEN. HE CAUGHT HIMSELF ON HIS WRIST, RESULTING IN A SPRAIN TO HIS RIGHT WRIST.

EMPLOYEE WAS DISMOUNTING THE TRUCK WHILE PARKED AT THE DUMP HOPPER. AS HE STEPPED ONTO THE GROUND, HE FELL BACKWARDS CATCHING HIMSELF WITH HIS LEFT ARM.

ON 6/27, EE REPORTED TO HIS SUPERVISOR THAT HIS BACK WAS SORE AND HE NEEDED A COUPLE TYLENOL. HE SAID THE 40 TON TEREX HE WAS OPERATING RODE ROUGHER THAN THE CAT 777 HE NORMALLY OPERATED. HE F INISHED THE SHIFT AND WORKED 6/28 WITHOUT INCIDENT. HE REPORTED THE INJURY ON FRIDAY 6/30.

EE WAS HELPING SUPERVISOR ON A DRILL RIG IN THE QUARRY. THE SUPERVISOR TURNED TO SPEAK TO EE AND SAW HIM BACK UP AND TRIP OVER A DIRT PILE OF DRILL CUTTINGS. EE FELL STRIKING RIGHT ARM ON A PI ECE OF DRILL STEEL.

EE WAS POURING CONCRETE ON 7-1-98 AND SPLASHED SOME ON HIS RIGHT PANT LEG. WHEN THE JOB WAS COMPLETE HE NOTICED A RASH ON HIS LEG.EE WORKED THE REST OF THE WEEK. ON 7-6-98 EE REPORTED TO WORK AND INFORMED SUPERVISOR THAT THE RASH WAS STILL ON HIS LEG. HE WENT TO THE DR. ON 7-6-98 AND WAS DIAGNOSED AND TREATED FOR 2ND DEGREE BURNS. EE RETURNED TO WORK NEXT DAY WITH NO RESTRICTIONS.

EE WAS TRYING TO IGNITE WELDING TORCH. SEVERAL UNSUCESSFUL ATTEMPTS WERE MADE WHEN EE FELT THE HANDLE GETTING HOT. BEFORE HE COULD THROW THE TORCH DOWN, FLAME FLASHED BACK THROUGH THE 02 HOSE, BURNING LEFT HAND AND APPROX 2 FT OF HOSE. EE SUSTAINED 2ND AND 3RD DEGREE BURNS TO LEFT HAND.

EE WAS COMING DOWN THE STEPS IN THE SECONDARY WHEN HIS FOOT SLIPPED OFF A STEP. HE LANDED ON THE NEXT STEP WITH HIS KNEE.

EMPLOYEE WAS BENDING OVER HITTING A STOP WRENCH WITH A HAMMER WHEN HE FELT HIS BACK PULL.

EE STEPPED OFF THE BOTTOM STEP OF A R-35 HAUL TRUCK ONTO THE FUEL HOSE. HE TWISTED HIS ANKLE ANDFELL TO THE GROUND. HE LANDED ON HIS TAILBONE.

EMPLOYEE WAS BENDING DOWN TO PUT A PLUG INA WATER PUMP WHEN HISKNEE GAVE OUT.

EMPLOYEE WAS LIFTING A 20 FOOT PIECE OF CHANNEL WITH ANOTHER EMPLOYEE ONTO A TRUCK TO CUT WHEN HE FELT SOMETHING PULL IN HIS BACK.

EE WAS CLIMBING INTO THE BOTTOM DECK OF SCREEN 1 WHEN THE METAL ANGLE HOLDING THE DOOR OPEN FELL DOWN ON THE EE'S HAND.

EMPLOYEE WAS HOLDING LEFT END OF BELT SCRAPER TO ALLOW EMPLOYEE TO REMOVE THE RIGHT END BOLT. THE LEFT END BOLT HAD ALREADY BEEN REMOVED. EMPLOYEE DID NOT TELL INJURED WHEN HE WAS GOING TO REM OVE THE SECOND BOLT. WHEN EMPLOYEE REMOVED THE SECOND BOLT, THE SCRAPER JERKED INJURED'S SHOULDER BEFORE HE COULD LET GO OF THE SCRAPER. THE ROPE WAS TO LONG TO PREVENT SHORT FALL OF SCRAPER.

WHILE ASSEMBLING A TRACK ADJUSTER ASSEMBLY, EMPLOYEE WAS TAPPING THE IDLER YOKE WITH A HAND HELD SLEDGE HAMMER. AS THE PART STARTED TO GO TOGETHER, THE ASSEMBLY STARTED TO LEAN FORWARD. EMPLOY EE WAS SWINGING HAMMER WITH LEFT HAND AND STRUCKRIGHT HAND THAT WAS HOLDING THE YOKE FROM MOVING FURTHER TOWARDS THE EMPLOYEE.

EE & ANOTHER EE WERE MOVING A WELDING STAND FROMTHE CENTER OF THE SHOP FLOOR TO BE FLUSH WITH THE BACK WALL AND NEXT TO A WORK BENCH. IN POSITIONING THE WELDING STAND, EE CAUGHT HIS HAND BETWE EN THE STAND & BENCH.

EE WAS LIFTING A HEAVY HYDRAULIC CYLINDER TO REMOVE A LIFTING STRAP. PULED MUSCLE IN LOWER BACK WHEN LIFTING.

EE WA SFUELIGN A LOADER. HE WAS CLIMBING UP THE LADDER WITH THE FUEL HOSE IN ONE HAND. HIS FOOT SLIPPED AND HE FELL LANDING ON TOP OF CONCRETE CONTAINMENT WALL. HE BRUISED HIS LEFT RIBS. E E WAS APPROX 6 RUNG SHIGH ON THE LADDER WHEN HE SLIPPED.

EE WAS DIRECTING CRANE OPERATIONS WHEN A CABLE CAME LOOSE & BELL AGAINST HIS BACK CAUSING A CUT.

EE WAS REMOVING BOLTS ON A LOADER AND PULLED MUSCLE IN BACK.

EE WAS STEPPING FROM FUEL TANK STEP FROM MIXER STEPPED ON A 3-4" ROCK WITH LEFT FOOT, DID NOT NOTICE ANY PROBLEM, ABOUT 20 MIN LATER HE WENT TO TIE HIS SHOE AND GOT A SHARP PAIN IN HIS LEFT KN EE.

EE WAS WELDING CHIPING OF SLAGS OFF METAL WENT OVER TOP OF GLASSES CAUSING A SLAG TO GET INTO HIS EYE.

EE WAS MOVING A 55 GALLON OIL BARREL WITH A 2 WHEEL CART, WHILE PULLING BACK ON THE CART HANDLES TO TIP OVER THE BARREL HE PULLED HIS LOWER RIGHT BACK.

TAKING A BAR PULLING ROCK OUT FROM UNDER CONVEYOR BELT, A ROCK FROM OFF THE TOP OF BELT FELL DOWN ON EE'S FINGER CAUSING A BROKEN INDEX FINGER ON RIGHT HAND TIP & MIDDLE BONE FROM TIP.

EE WAS STANDING BACK OBSERVING THE LIFT WHEN THEWELDED LIFTING EYE BEING USED TO PULL A PIN FROMCRUSHER BROKE FREE & STRUCK HIM ON HIS SAFETY GLASSES CUTTING HIM ABOVE HIS EYE.

HE WAS LEANING DOWN TO PICK UP ELECTRIC DRILL AND PULLED A MUSCLE IN THE LOWER BACK.

MR. NAPIER WAS STANDING WITH HIS FOOT INSIDE 992D LOADER WHILE KEN KELLY WAS MARKING OUT WHERE TO CUT. STEVE CATES RAISED THE BUCKET AND THE FRONT EDGE HIT MR. NAPIER ON THE RIGHT KNEE CAP.

INJURED HAD PULLED HAUL TRUCK TO GREASE AND FUEL BAY. HE HAD GREASE GUN IN HIS HAND AND WAS GREASIGN TRUCK. LIGHTNING STRUCK POWER LINE NEXT TOT HE SHOP AND HE WAS SHOCKED BY IT.

INJURED WAS LOADING EXPLOSIVES ON A QUARRY SITE AND WAS OVERCOME BY HEAT.

EMPLOYEE CUT LEFT HAND BETWEEN THUMB AND INDEX FINGER WHILE HE WAS USING PINCH BARS TO HOLD A BELT WHICH HE WAS SPLICING.

EMPLOYEE WAS PASSING FUEL NOZZLE TO ANOTHER EMPLOYEE. HE FELT A SHARP PAIN IN HIS BACK WHEN BENDING OVER. NOZZLE WEIGHED APPROX. 2-4 LBS.

EMPLOYEE WAS WORKING ON 51/2FT CRUSHER & WAS PULLING ON WRENCHES & SWING HAMMER WHEN HE HURT HIS LEFT SHOULDER

INJURED OCCURRED WHEN EMPLOYEE ATTEMPTED TO UNSCREW HEAD FROM DRYRITE PUMP. AIRLINE TO PUMP HEAD WAS UNDER 125 PSI BECAUSE OF PLUGGED LINE. WHEN PUMP HEAD DECOUPLED, AIR LINE STRUCK EMPLOYE ON ELG AND HEAD.

EMPLOYEE WAS UNLOADING STEEL OFF BACK OF A TRUCK. HE SLIPPED ON LOOSE ROCK AND CAUGHT HIS RIGHT HAND BETWEEN THE STEEL AND THE TRUCK.

54736YEE WAS LETTING TOP/PLATE DOOR DOWN. HE WENT TO TAKE THE COME-A-LONG HOOK OFF THE DOOR. T HE DOOR WAS NOT CLOSED COMPELTELY. THE DOOR FELL AND CUAGHT HIS FINGER BETWEENT HE COME-A-LONG 15403HE DOOR.

INSIDE S-4 SCREEN CHECKING FOR HOLES.BACKED UP AND HIT NECK ON THE X-BAR.

HE WAS GETTING INTO HIS TRUCK AFTER GREASING IT. HE HAD GREASE ON HIS FOOT AND SLIPPED OFF THE SECOND STEP. HE FELL BACK TO THE FIRST STEP ON HIS TRUCK AND INJURED HIS BACK.

TIGHTENING NUT WITH HAMMER AND WRENCH. PINCHED FINGER ON GUARD AND WRENCH

EMPLOYEE WAS ON BACK OF FLAT BED TRUCK WITH FUEL TANK AND GREASE APPLICATION ON IT, HE HAD HOSE IN HAND AND STARTED TO GO DOWN HAND RIALS AND LADDER, HE GOT TO THE EDGE OF TRUCK AND HIS RIGHT FOOT SLIPPED OFF AND HIT RIGHT SIDE OF BACK.

SMASHED RIGHT MIDDLE FINGER WITH HAMMER WHILE INSTALLING PVC PIPE.FOUND OUT ABOUT FINGER BROKEN 04-05-91.AT THE TIME OF ACCIDENT HE DID NOT FEEL IT NECESSARY TO GO TO THE DOCTOR OR HOSPITAL TO GET IT CHECKED OUT.

HE WAS STANDING INSIDE OF S-2 SECREEN WHILE REPALCING BOTTOM DECK SCREENS. HE WAS TURNING AROUN WENT TO STEP DOWN AND MISSED THE STEP AND HIT LEFT KNEE AND LEG ON SUPPORT BAY.

EMPL GETTING OIL,STEPPED ONTO ICE-COVERED BOARD SLIPPED OFF BOARD,RESULTING IN BROKEN LEFT ANKLE BONE.

I NAME WAS WELDING ON SCREEN 4. HOT SLAG FROM THE WELDING ROD FELL ON TOP OF HIS LEFT BOOT TONGUE AND BURNED THRU THE TONGUE OR THE BOOT ONTO THE LEFT SIDE OF HIS FOOT.

WHILE EMPLOYEE WAS SANDING NEXT TO CTRUSHED OIL TANK THE CRUSHED OIL TANK LID SLID DOWN STAIRS STRICKING EMPLOYEE ON THE HAND

EMPLOYEE WAS HELPING 3 OTHER MEN TO CHANGE OUT CONVEYOR IDLER.LEFT AHND GOT PINCHED BETWEEN IDLER FRAME AND CONVEYOR FRAME.

EMPL TURNING CONVEYOR BY PULLING ON MOTOR DRIVE BELTS.THE CONVEYOR MOVED EASY AND I.NAME DIDNT LET GO OF BELT IN TIME.IT CAUGHT HAND IN PULLEY AND BROKE LEFT INDEX FINGER.CONVEYOR WAS LOCKED O UT.HE RETURNED FOR LIGHT WORK 2-7-90.

I NAME WAS TAPPING A MACHINE GEAR WITH A HAMMER WHEN A PIECE OF STEEL FLEW INTO HIS RT EYE NEITHER HE OR THE FOREMAN KNEW ABOUT IT UNTIL THE NEXT DAY WHEN HE WAS HAVING PAIN & CLOUDINESS OF TH E EYE PIECE OF STEEL CAUSED A CUT TO THE CORNEA OF THE EYE

HE WAS CLEANING WITH THE WATER HOSE AND HOLDING HOSE BETWEEN HIS LEGS. WHEN THE OTHER HOSE WAS TURNED OFF, PRESSURE BUILT UP ON HIS HOSE. THE PRESSURE ON HIS HOSE HIT HIM ON THE LEFT KNEE CAP KNOCKING IT OUT OF PLACE. NOTE- BOTH OF HIS KNEES HAVE BEEN INJURED BEFORE AT SCHOOL FROM WRESTLING.

EMPL CUT FINGER HANDLING WIRE SCREEN CLOTH. IT WAS SUCH SMALL CUT THAT HE FELT HE DIDN'T NEED DR. THEN ON 10/03/89 HE NOTICED HE HAD INFECTION SO HE WENT TO DR.

EMPL TRIPPED OVER WATER HOSE & HIT FACE ON DOOR CASING.

I.NAME WAS WORKING WITH EMP 2 ON JOB SITE, AND WAS REMOVING LIFT CYLINDER; HE HAD 2 BOLTS IN CYLINDER. THE CYLINDER BLEW OUT, AND BUCKET STARTED TO FALL. I.NAME JUMPED OFF BACKHOE TO GET OUT O F THE WAY OF THE BUCKET AND CYLINDER WHEN BACKHOE RAN OVER HIS RIGHT FOOT.

I NAME WAS MAKING A SPLICE REPAIR ON CONVEYOR #2 WHEN THE CHAIN LEVER HOIST BEING BACKED OFF ON ANOTHER SECTION OF THE BELT SLIPPED PULLING THE BELT OUT FROM UNDER HIM AFTER MOVING HIM ABOUT 1 5' DOWN THE CONVEYOR RESULTING IN A BRUISED BACK

THE INJURED WAS SITTING ON CONVEYOR #2 BACKING OFF A CHAIN LEVER HOIST WHEN THE HOIST DID NOT HOLD.THE CHAIN HOIST FREE WHEELED LETTING THE BELT COME DOWN AT A FAST RATE WITH HIM ON IT.HIS RIG HT LEG WAS PULLED UNDER A SKIRT BOARD AND DISLOCATED.

HE WAS OPERATING A HAUL TRUCK AND WAS RETURNING FROM THE DIRT DUMP WHEN HE HIT A BUMP CAUSING THE SEAT TO SPRING DOWN THEN BACK UP HITTING HIS HEAD ON THE ROOF OF THE CAB RESULTING IN A NECK S PRAIN.

THE EMPLOYEE WAS CLEANING MUD FROM THE ROCK FEEDER WITH A PICK AXE WHEN HIS HAND CAME INTO CONTACT WITHA PICE OF STEEL METAL WHICH RESULTED IN A CUT MIDDLE FINGER OF THE RIGHT HAND.TWO STITCHE S.

THE EMPLOYEE WAS SHOVELING DIRT AND MUD WHEN SHE PULLED A MUSCLE IN HER LEFT SHOULDER.

THE EMPLOYEE WAS LOOSENING BOLTS ON THE CRUSHER WHEN HIS RIGHT HAND SLIPPED OFF THE WRENCH AND HIT A BOLT RESULTING IN INJURY TO HIS RIGHT THIRD FINGER.

EMPL WAS LIFITNG AND PULLING A WHEELBARROW WHEN HE SUSTAINED A BACK SPRAIN

THE EMPLOYEE WAS SWINGING A SLEDGE HAMMER DRIVING WEDGES IN A 4 1/2 SHORTHEAD CRUSHER WHEN HE TWISTED HIS LEFT KNEE.

EMPLOYEE WAS MOVING MOTOR MOUNT BOLTS WITH HAND WRENCH AND STRAINED TOO MUCH RESULTING IN PULLED MUSCLE TO GROIN AREA.

EMPLOYEE ALLEGES THAT HE WAS INJURED WHILE LOOSENING PIPE CAPS ON WASH TOWER SPRAY BARS WITH A PIPE WRENCH WHICH RESULTED IN A PULLED MUSCLE IN THE UPPER BACK AND NECK AREA INCLUDING A POSSIB LE PINCHED NERVE.

EMP WAS FILLING A SCREW GEAR BOX WITH OIL WILE STANDING IN A LOADER BUCKET. HE SLIPPED ON MUDDY SURFACE OF BUCKET AND INJ HIS BACK.

EMPLOYEE WAS USING A PICK AXE CLEANING A CHUTE AND WAS HANDLING SCREENS AT THE SCREEN TOWER WHEN HE SUSTAINED INJURY TO THE MUSCLES IN THE MIDDLE OF HIS BACK.

EMPLOYEE WAS CUTTING A PIECE OF RUBBER WHEN RAZOR KNIFE SLIPPED CUTTING TOP OF LEFT HAND.

INJ USING COTTER PIN TO REMOVE UPPER CRANKSHAFT BEARINGS,CAUGHT LEFT HAND IN COUNTER-WEIGHTS WHEN BUMPING CRANKSHAFT OVER WITH ELECTRIC STARTER.

INJURED WAS WELDING LIONER IN SURGE IN SHUTE -ROCK FELL DOWN FROM OVERHEAD AREA

EE WAS INJURED 4HILE TURNING AROUND ON STAIRWAY. HE TURNED AROUND & BUMPED INTO HANDRAIL BRUISING HIS RT SHOULDER.

EMPLOYEE WAS HO5DING LIGHT FOR ANOTHER EMPLOYEE WHO WAS OPERATING GRINDER WHEN HE WAS STRUCK IN THE EYE BY A GRINDING CHIP.

MAN WAS LIFTING3DOOR ON WASH SCREEN HOPPER. PULLED MUSCLE IN LEFT SHOULDER AND ARM.

SHOVEL OPERATOR3WAS SWINGING LOAD ONTO TRUCK.WHEN HE RELEASED SWING LEVER,SHOVEL DID NOT STOP CAUSING BUCKET TO HIT BACK OF TRUCK.THREW TRUCK OPERATOR FORWARD IN CAB AND CAUSED WHIPLASH.

EMPLOYEE WAS WE5DING, CHIPPINGH OFF HOT SLAG, WHICH FELL INTO HIS BOOT AND BURNED LEFT EYE & ANKLE.

EMPLOYEE WAS WA5KING BY 4 1/4 CRUSHER,LOOKED UP AND ROCK FELL HITTING HIM IN THE CHIN AND MOUTH.

EMPLOYEE WAS AS8ISTING 2 OTHER PEOPLE IN CARRYING A 48 X 60 PIECE OF 1/4" PLATE INTO SURGE TUNNEL FEEDER. NOTIFIED FOREMAN THAT HE HAD HURT HIS BACK 5:00PM 03-09-87. REPORTED FOR WORK ON FRID AY 03-20-87. WE3T TO DOCTOR ABOUT 8:30 AM.

EMPLOYEE WAS US3NG CUTTING TORCH IN MUDDY AREAS SLIPPED & BURNED RT WRIST WITH ACETYLENE TORCH

WAS USING HANDL9 OF 3 LB HAMMER TO DRIVE SKIRTING DOWN MISSED THE SKIRTING AND HIT 3 RD FINGER ON RIGHT HAND.

EMPLOYEE WAS LO2SENING ADJUSTING NUT ON CONVEYOR DRIVE MOTOR WHEN HE STARTED FORMING THE CENTER BAR WITH A PIECE OF REBAR REBAR SLIPPED AND EMPLOYEE HIT HIMSELF IN THE MOUTH CRACKING A TOOTH A ND LOOSENING AN2THER

EMPLOYEE WAS CH9CKING SHOVEL FOR HYDRLIC LEAK. OPENED OPERATOR CAB DOOR AND HYD LINE BURST HITTING LEFT EYE WITH HYD FLUID.

EMPLOYEE WAS TA5ING ROLLERS OFF OF CONVEYOR BELT WHILE STANDING ON TOP OF VAN. HE STEPPED ON FIBER SUNROOF AND FELL THOUGH.

EMPLOYEE WAS RE4OVING DIRT AND ROCK BETWEEN DOZER TRACKS.SHOVEL HIT ROCK AND EMPLOYEE FELT A POP IN HIS LOWER BACK.

EMPL JUMPED FROM BED OF TRUCK BEING UNLOADED EMPL TWISTED AND BADLY SPRAINED RIGHT ANKLE.