Hamburg Quarry Metal/Non-Metal

EE felt a pop in EE's left knee while lifting an I-beam. Did not seek medical treatment until 6/17/2024

EE got debris in right eye. Dr visit 6/7/2024.

The employee was utilizing a torque multiplier tool to remove a tie rod form a hydraulic rock breaker and while releasing tension on the multiplier the ratchet that EE was using broke a tooth, skipped and quickly spun around and caught the employee's hand and caused a laceration.

Employee tripped and fell while walking on the cat walk.

The employee was attempting to open the ladder for the 57's catwalk when EE felt a pop and severe pain in EE's left arm.

While reattaching a guard, the guard slid, pinching the employee's finger.

Employee was performing maintenance on the screen deck of a wash plant. Employee slipped and fell backwards and struck against a chute work on the right side of rib area.

Ee was working on belt. the need was to remove a rock slab from the belt. ee was accompanied by another employee. in process of removing the slab, the slab slipped and landed on ee's left wrist. ee immediatley notified about the incident to plant manager. ee was taken to urgent care location where X-Ray were performed. the X-ray reports came back negative. ee on light duty

Employee parked haul truck to take a break. Employee stated slipped and fell while walking across the haul truck parking area. With all the rain we were getting the area may have been slippery.

On Tuesday 2/14 around 7:10 am EE was rolling up a 24 inch wide conveyor belt when EE slipped and fell, injuring lower back. This incident was not reported until Wednesday 2/15 by text messaging Supervisor at 2:27 am. Supervisor called and informed me about the incident.

While installing an engine on a Caterpillar 992G machine, our Field Service Technician was under the machine installing the drive shaft and hydraulic lines. While attempting to move from under the machine, our Technician hit hard hat on the step located on the side of the machine knocking off hard hat resulting in a scalp laceration requiring stitches.

Employee bending over to fix Bucket Pin on 992G Cat - his hard hat fell off and he hit his head on a steel lock plate - laceration required stitches

EE was working on the 3/4 cross belt - while prying an idler from the conveyor, EE caught his left ring finger between the conveyor and bar. Finger is fractured.

EE slipped on patch of ice causing him to lose his balance and fall backwards on his right ankle. Fibular Fracture - surgery needed.

Employee was operating the loader and when he pulled the shift lever to change gears he strained his neck.

Employee climbed down from loader and stepped into a small hole and twisted his right ankle

Employee was changing screen panels on the Telsmith #2 middle deck. When he rolled over to reach for a panel he felt pain in his chest area. He was taken to the hospital and diagnosed with a pulled chest muscle.

Employee was operating the man lift in order to remove snow from the conveyor belts. As he was elevating the man lift up under a conveyor, the machine cover on the man lift came too close to an "I-Beam" and his hand got caught between the control panel and the underside of the I-Beam. He lacerated his hand requiring 5 stitches and has hairline fractures on 2 fingers. Right Hand.

Employee was injured when he was replacing the side guard on a loader bucket. The mechanic had one of the bolts in place and was using a 4 lb hammer to hit the side guard in order to align the other hole. The hammer struck the side guard and a steel chip flew off and struck his right inner thigh. The piece of steel went through his clothing and had to be surgically removed.

Two steel plates approx. 2'x 4' were set against each other upright near the base of the crusher, when EE was putting a clevis on one plate, they fell over his leg. EE's leg was broken from the weight of the plates.

CHANGING SHAFT AND BEARINGS ON WASTE PUMP AT WASH PLANT, LIFTING SHAFT INTO POSITION TO CHANGE HE INJURED HIS LOWER BACK. TORN LIGAMENT IN LOWER BACK.

EMPLOYEE WAS PREPARING TO LEAVE TRUCK AT END OF SHIFT FOR REPLACEMENT OPERATOR. HE LEFT CAB CARRYING LUNCH BUCKET AND OTHER PERSONAL EFFECTS, WALKING ACROSS CAB-LEVEL PLATFORM TO RIGHT SIDE O F PLATFORM TO ADJUST RIGHT SIDE MIRROR. EMPLOYEE DID NOT PROPERLY USE AVAILABLE HAND RAIL, LOST BALANCE AND FELL TO GROUND.

EMPLOYEE WAS WALKING THRU YARD WHEN HE SPRAINED HIS RIGHT ANKLE.

EMPLOYEE WAS REBUILDING BUCKET ON FRONT-END LOADER. WHILE HE WAS CUTTING PLATE OFF BOTTOM OF BUCKET, IT SLIPPED FROM HIS HANDS AND FELL ON HIS FOOT. EMPLOYEE DID NOT LOSE ANY TIME UNTIL O5-O5- 93. HIS FOOT IS BRUISED.

EMPLOYEE WAS CLIMBING UP ON SIDE OF SCREEN TO VISUALLY CHECK SCREEN CLOTH. (SCREEN WAS NOT RUNNING. BEFORE STARTING PLANT). HIS FOOT SLIPPED AND HE HURT HIS BACK.

EMPL WAS HAULING SCRAP WOOD FROM SHOP RECONSTRUCTION TO DUMP SITE. PIECE OF WOOD STUCK IN BODY OF 35 TON TEREX ROCK TRUCK & EMPL JUMPED INTO BODY TO THROW WOOD OUT BY HAND. WHEN HE JUMPED IN H E SPRAINED LEFT ANKLE.

EMPLOYEE WAS MOVING A DRILL RIG AFTER STOPPING HE WENT TO STEP OFF RIG & STEPPED ON A ROCK & TWISTED HIS ANKLE

EMPLOYEE WAS HELPING ANOTHER EMPLOYEE CHANGE RUBBER SCREEN PANEL IN #1 SCREEN ATTEMPTED TO LIFT A PANEL & PULLED A MUSCLE IN THE GROIN AREA

INJURED EMPLOYEE WAS TRYING TO MOVE A SLURRY PUMP BEARING COVER WHILE CLEANING A BUILDING. THE COVER FELL OVER AND STRUCK HIS RIGHT HAND.

6AT ABOUT 2:00PM, 1 HR BEFORE THE END OF HIS SHIFT HH TOLD HIS SUPERVISOR THAT HIS BACK HURT & THAT HE COULDN'T SHOVE ANYMORE TO CLEAN UP, NO MENTION WAS MADE OF BACK INJURY AT THAT TIME. THE FOLLOWING DAY HE CALLED IN TO REPORT OFF, SAYING HIS BACK HURT. ON 7/11/90 HE WENT TO SEE A DOCTOR, CLAIMING A WORKMANS' COMPENSATION.

HE IMPROPERLY LIFTED A ROCK.

INJURED WAS REPLACING THE BRAKE SHOES ON A MACK DUMP TRUCK. HE WAS SPREADING THE SHOES WHEN THE PRY BAR SLIPPED, CATCHING THE END OF EMPLOYEE'S FINGER. TRUCK WAS JACKED UP IN SHOP AT THE TIME.

EMPL WAS WORKING ALONE IN GARAGE INSTALLING HEADLIGHT BRACKETS ON D6 BULLDOZER. HE WAS USING HAND TAP TO CLEAN OUT THREADED HOLE IN DOZER WHEN SUDDENLY TAP BROKE & PIECE OF TAP STRUCK HIM IN E YE. HE WENT INTO NEXT BAY OF GARAGE & HAD FELLOWEMPL TAKE HIM TO ER.

EMPLOYEE WAS HELPING TO REPLACE A WEAR PLATE IN THE FEED BOX OF 7 FT SHORTHEAD CRUSHER WHEN HE SLIPPED AND HIT HIMSELF IN THE GROIN AREA,OR PULLED A MUSCLE IN THAT AREA.

EMPLOYEE WAS WORKING AROUND JAW CRUSHER MAKING REPAIRS HE BUMPED AGAINST A LARGE WRENCH LEANING AGAINST CRUSHER THE WRENCH FELL OVER & STRUCK HIM ON LEFT INSTEP BEHIND THE SAFETY TOE CAP HE WO RKED FOR ANOTHER 31/2 HRS BEFORE GOING HOME M

EMPLOYEE WAS WORKING IN JAW CRUSHER DISCHARGE CHUTE MAKING REPAIRS. HE WAS LIFTING STEEL BARS AND STRAINED HIS BACK.

CLIMBING SHORT LADDER UNDER BIN SLIPPED O;N LADDER, FELL 4 FT TO LEVEL GROUND RAINING AND LADDER WET AND POSSIBLY SLIPPERY EMP WAS CARELESS

EMPLOYEE LIFTED TIRE AND WHEELL OFF THE FLOOR OF SHOP BY HIMSELF AND PULLED MUSCLES IN HIS BACK.

HELPING CRUSHER OPERATOR CRUSHER TOGGLE BLOCK CRUSHED HAND.

EMPLOYEE WENT TO CHECK BELTS DRIVING THE MAIN SLURRY PUMP SAND PLANT. HE TOLD PLANT OPERATOR TO SHUT OFF ELECTRIC MOTOR, WHICH WAS DONE. HE REACHED BEHIND GURAD TO CHECK BELTS AND PUMP TURNE D BACKWARDS FROM BACKFLUSHING WATER. THE FINGERS OF RIGHT HAND WERE CAUGHT BETWEEN BELTS AND SHEAVE.

EMPLOYEE WAS HELPING HIS SUPERVSOR AND ANOTHER EMPLOYEE MOVE SOME WIDE FLANGE BEAMS TO MAKE ROOM FOR A CRANE. THE INJURED EMPLOYEE STEPPED BETWEEN TWO OF THE BEAMS IN PREPARTION FOR PLACING A PLATE ON ONE OF THE BEAMS.

EMPLOYEE WAS PREFORMING MAINTENCE WORK ON DISCHARGE CHUTE OF SCREEN. CONDITIONS WERE NORMAL, WETAHER GOOD. EMPLOYEE SLIPPED AND TWISTED HIS LEFT ANKLE, FOR NO APPENRT RESON.

EMPLOYEE WAS HAVING TRUCK TROUBLES TOOK TRUCK TO SHOP.STEPPED OUT OF PASSENGER DOOR,STEPPED ON OLD HYDRAULIC HOSE,AND TWISTED ANKLE.

EMPL WALKING ACROSS RECENTLY SHOT MUCK PILE TO GET TO AIRTRACK TRIPPED ON ROCK FELL,SPRAINED HIS ANKLE.

EMPLOYEE WAS OPERATING BIN GATE TO LOAD TANDEM DUMPS UNDER SCREEN TOWER. EMPLOYEE HAD BEEN INSTRUCTED TO MOVE OUT OF A REA UNTIL TRUCK WAS POSITIONED AND STOPPED COMPLETELY. HE FAILED TO DO T HIS AND WAS PINNED AGAINST SCREEN TOWER WALL BY TRUCK.

EMPLOYEE WAS SHOVELING UNDER SAND PLANT FEEDER WITH OTHER EMPLOYEES TWO DAYS LATER HE COMPLAINED OF PAIN IN RT. ARM WENT TO DOC.AT HOSPITAL G.R.&DR.TOLD HIM TO REST ARM

INJURED WAS WALKING THROUGH SAND PLANT AREA WHEN HE SUDDENLY FELT PAIN IN RIGHT CALF. EMPLOYEE MISSED WORK ON 5-27-88.

INJURED WAS HELPING OTHER DRILLER ATTEMPT TO BREAK DRILL STEEL STRING WHEN STEEL CHIP FLEW FROM COUPLING & PENETRATED RT.ARM OUT PATIENT SURGERY PERFORMED AT HOSPITAL TO REMOVE STEEL CHIP

IST WAS RAINING ON INCLINED STEEL BARS

EMPLOYEE SLIPPED ON GREASE SPOT ON FLOOR WHILE OPENING GARAGE DOOR AND WRENCHED KNEE AND BACK.

EMPLOYEE WAS WORKING UNDER PRIMARY IN CRAMPED POATION AND COLD WEATHER FOR SEVERAL HOURS WELDING NEW STEEL HOPPERS. HE MENTIONED SORE BACK TO SUPERVISOR.

EMPLOYEE WAS AT7EMPTING TO CARRY A LENGTH OF ANGLE IRON AND AGGRAVATED A CLAIMED PRIOR INJURY.

CLIMBED UP TO CLEAR JAM STEPPED DOWN ROCKS METAL GAVE WAY TWISTED ANKLE.

HELPING MOVE LADDER UNDER BINS FOREIGN SUBSTANCE BLEW INTO EYE-R- PIECE OF STEEL.

REMOVING STEEL FROM DRILL, HAND CAUGHT BETWEEN STEEL & DRILL

BARGED INTO GREASE BARRELL LID PUNCHTURE WOUND 6 WRIST 5 STITCHES.

CAUGHT FINGER BETWEEN CRANK HANDLE AND BODY OF TRUCK WHILE UNTARPING THE LOAD, BBOLT CUT LEFT SMALL FINGER REQUIRING 5 STITCHES.

STRAIGHTING TIE RODS WITH JACKS AND TURNED WHEEL, FINGER CAUGHT BETWEEN FENDER AND WHEEL.

SITTING ON BELT, CUTTING HOSE WITH KNIFE. KNIFE SLIPPED, CUT LEG. JUMPED FROM CONVEYOR AND INJURED BACK. BACK INJURY NOTIFIED ON TUESDAY JUNE 5, 1984.

REMOVING BROKEN WHEEL STUD W/ENY OUT AND A HAMMER AND ADJUST WRENCH EG YOUR FALL OUT ASST TAPPED WITH HAMMER PIECE OF FOREIGN MATTER FLEW INTO EYE.

CLEANING PARTS, STEEL FRAGMENTS LEFT EYE

DRILLING HIT MUD FLEW INTO L EYE.

WET STEPS-FELL OFF LOADER-JAMMED KNEE ON GROUND.

FOREIGN BODY RT EYE

WHEN CHANGING SCREENS, WIND BLEW DUST INTO EYES

FELL OFF TRUCK

RELEASING TRIP FOR GATE UNDERPRESSURE STRUNG DOWN AND STRUCK ARM HIT UPPER BICEP

WET SURFACE OF SCALPING SCREEN CHUTE. EMPLOYEE SLIPPED AND BUMPED HIS BACK. WORKING IN FINES CHUTE UNDER SCALPING SCREEN.

EMPLOYEE WAS WALKING WHEN HIS FEET BECAME ENTANGLED IN SCREEN CLOTH AND HE TRIPPED AND BROKE HIS ANKLE

EE WAS CLEANING CHUTE OF CONCRETE MIXER WHEN PICK HE WAS USING SLID INTO BARREL OF MIXR & CAUGHT HIS FINGER.

WAS IN GARAGE AND ANOTHER EMPLOYEE WAS GRINDING A METAL GEAR WHEN A PARTICLE OF STEEL FLEW. STRUCK HIM IN THE EYE.

EMPLOYEE WAS HOLDING A PIECE OF STEEL WHILE ANOTHER PERSON WELDED HE SUFFERED WELDING FLASH TO BOTH EYES AS A RESULT

EMPLOYEE WAS LIFTING RAM INTO PLACE ON DOZER WHEN HE PULLED HIS LOWER BACK MUSCLE.

EMPLOYEE WAS INSTALLING A TAKEUP ON A CONVEYOR WHEN IT FELL OFF CONVEYOR AND HIT HIM ON HIS LEFT FOOT. FOOT IS BADLY BRUISED, NO BROKEN BONES.